1. Phoenix Thermo Electric USA LLC
Presents the Greenest, Highest Efficiency Electrical Power In the
World
2. Phoenix Thermo Electric USA LLC
Power generation by alternative technologies in recent decades it has held a leading role in the
economic, political and social environment. Having a clean energy production has been a priority for
many governments, even though till now, there is not an alternative technology in the market which
can be profitable enough to implement massive productions without requiring a government
subside .
4. Phoenix Thermo Electric USA LLC
After 25 years of continuous research Phoenix Thermo Electric has developed a Solid-state
electrical generator, whose technology can achieve an efficiency and profitability exceeding
any current scheme electric energy production by alternative means.
The Solid State Electric Generator has no moving parts except a small fan that distributes heat
flow on a set of thermal electric exchangers. This generator is also a multiple choice
generator, in reference to a heat source power generation, this mean it can use any heat
source as Thermo Solar Energy, , thermal energy or any combustible to generate heat as
Natural Gas, Carbon, bio-fuels, Diesel, etc.
5. The Thermoelectric technology based on the principle of heat exchange to generate electricity it
is not a new concept in the market, however no other recently technological innovations of
electricity generation fields have created a cost-effective option for alternative mass generation
of electricity, that needs no government subsides.
Phoenix Thermo Electric USA LLC
Phoenix Thermo Electric USA uses the
Seebeck principle - Horton effect have
achieved the Solid State Electric Generator
development by using metal heat
exchangers made of alloys that have been
optimized over 25 years of research. Those
optimized alloys in combination with the
arrangement and circular configuration
thereof, allows to generate energy in
quantities never before achieved under this
principle with high efficiency.
7. Horton Engine
Heat and Current Flow Diagram
Titanium rod for air circulator penetrates here
Cooling Cooling
Insulated Barrier
Termoeléctric Wafers create Voltage
here as heat moves upward across the
heated transfer fins
“Hot” end of heat
transfer fins
Heating
14,000 Amp
Current Flow
Tensioned Metal
Binding
Fan ( Not Shown)
8. Control
Module
ThermoElectric Generator
Electrical Output
Insulation Layer
Heated Matrix
With Air Gaps
Heating Coil
Electrical Input
Closed System:
(1) Energy Stored in Matrix
as heat.
(2) Heat drawn up as
superheated air.
(3) Creates a heat Flow
through solid state
generator
(4) And is pushed back into
storage matrix.
(5) Grid-Matched AC or DC
current output from
Control Module
Heat Store
Heat Store Mechanics
10. CONVENTIONAL SOLAR ENERGY
Current Solar Thermo Technologies, harness energy from the sun by reflecting concentrators sunlight
captured (from all angles), to a central tube containing water, which later pushes that heated steam from a
turbine to generate electricity. This process involves the need for a large amount of solar energy to produce
the necessary steam pressure in order to achieve the trigger pulse for the power generating turbine.
The turbine requires special facilities and has a high maintenance cost. The vapor transport facilities require
high maintenance: NOTE : Phoenix Technology does not use this principles.
This technology only woks when there is sun
11. P T E TECHNOLOGICAL INNOVATIONS
Within the field of Solar Thermo Power Generation Phoenix Thermo Electric has developed four
major technological advances to set a difference with current alternative Power Generating
technologies, those allow us to produce more electricity at lower cost:
1. - The tube where the solar energy is reflected does not contains water, it only carries heated
air which will provide the necessary heat source for power generation.
2. – The Electric Power Generation is performed based on thermal exchange between the
generator materials, which means that there is no needs of large amounts of energy to
produce electricity, as the one needed to move a turbine. In addition to the previous the energy
production is enhancing by the circular arrangement and double connection (Series and Circular).
3. - Introduction of the concept of heat storage, allowing it to maintain continuous and total
electricity production capacity for a minimum period of three days, even when there is no sun.
4 – PTE technology is multimodal or multiple as to the heat source used for power generation,
it can be used interchangeably solar energy, natural gas, LPG, coal etc. Either individually or any
combination thereof.
12. Advantages of Phoenix Thermo Electric
Compared to any alternative technology and even with conventional PTE Generator
System have a lower cost and faster implementing time.
The power energy produced by Phoenix Solid State Generator is significantly less expensive
than any alternative means, up to the point where it can compete with the
conventional energy production systems without requiring government subsidies to be
profitable.
Energy Production Plants developed by Phoenix Thermo Electric USA are modular and can
be adapted from 1 MW to the extent necessary for production according to the needs or
requirements of energy delivery.
PTE Generators have a low maintenance cost
Generator life is longer than the any other technology
13. Continue Electricity Production, supported by the heat storage.
Multi option heat resource, it is not limited.
Populations can be electrified easily without long transmission lines and without
great voltage drops
The electricity generated can be 100% clean Green energy.
Does not require large civil works adapted for operation.
Phoenix Thermo Electric USA LLC
14. Phoenix Thermo Electric vs. Wind
Power
Wind Power $1.75 per Watt for
PTE Power $1.50 per Watt
Wind Power 30 %
PTE Power 80 %
15. Phoenix Thermo Electric vs. Natural Gas
Burning Generation
Natural Gas Generator $2.75 per Watt
PTE Power $1.50 per Watt
Natural Gas Power 50 to 60 %
PTE Power 80 %
16. Phoenix Thermo Electric vs. Solar Power
Solar Panels Power $6.25 per Watt
PTE Power $1.50 per Watt
Solar Power 14 to 22 %
PTE Power 80 %
17. Phoenix Thermo Electric vs. Steam
Power
Steam Power $1.88 per Watt
PTE Power $1.50 per Watt
Steam Power 41.97 %
PTE Power 80 %
18. Phoenix Thermo Electric LLC
• To Produce Mega Watt PTE needs 1.2 acres of land
• Tested by the US Army’s Fort Monmouth Laboratory in New Jersey, based on their
findings, a large government contract will be awarded to PTE for power supply for the
defense department. Test results (unit will last for 50 years, reflector array for 20
years)
first three days 100 %, day 4 - 95 %, day 5 - 90
%, day 6 – 85 %, day 7 – 80 %, day 8 – 75 %, day 9 – 70 %, day 10 – 65 %, day 11 – 60
%, day 12 – 55 %, day 13 – 50 %, and so on (5 % decrease per day).
• due to cloud cover cost would be 2 to 3
cents per kWH
19. • Cost is 0.00216 USD per Kwh
• , the
generator requires 896,000 Btu-hours or 262,709 Watt-hrs of heat to make
one MW-hr of electricity for an hour
•In distance less than ¼ mile it is not necessary for a transformer to deliver
the energy to the distribution network.
Phoenix Thermo Electric LLC