53302372 config-gns3

QUEMU QUEDA TAL COMO ESTA

Arrastramos las imagens que requerimos routers y switch

Seleccionamos los 2 routers y click derecho sobre uno de ellos y elegimos configure

Y nos sale el siguiente menu

Vamos a slot y cambiamos donde dice wic 0 y elegimos WIC-2T

Apply y OK

Luego damos click en add link

Damos click sobre alguno de los objetos y nos muestra las interfaces para seleccionar ,
elegimos y apare automáticamente el cable para conectar a otro objeto a alguna de sus
interfaces

Una vez realizados las conexiones damos click en el icono que tiene la forma de un triangulo
verde

Al aparecer todos los puntos en verde significa que la estructura esta trabajando con
normalidad.

Luego damos click en le botón consoletoalldevice

Y aparece las siguientes ventanas

Nos percatamos que el rendimiento es pésimo del S.O. por lo cual, primero damos click en el
botón add link para que vuelva a su icono original, luegoselecionamos una de los routers y
damos click en Idle PC , aparece un cuadro y damos YES

Aparece un cuadro como el de la imagen

Damos click en la pestaña y seleccionamos alguno de los números que empiezan con *
damos aply y luego OK y con esto se reduce el consumo del CPU.

Username: cisco

Password:cisco

R1>enable

Password:class

R1#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

R1(config)#interface f0/0

R1(config-if)#

R1 con0 is now available

Press RETURN to get started.

ACCESO RESTRINGIDO - SOLO PERSONAL AUTORIZADO - TODAS LAS CONEXIONES SON
REGISTRADAS

banner motd

User Access Verification

Username: cisco1

Password:

R1>R1>

% Unknown command or computer name, or unable to find computer address

R1>R1>Password:


R1>% Unknown command or computer name, or unable to find computer address

^

% Invalid input detected at '^' marker.

R1>R1>Password:



^


R1>R1>R1>enable



^


R1>R1>Password:



^


R1>R1>R1#conf term

^


R1> ^


R1>% Invalid input detected at '^' marker.

^


R1>

R1>R1>Enter configuration commands, one per line. End with CNTL/Z.

^


R1> ^



^


R1>

R1>R1>R1(config)#username cisco password cisco

^


R1> ^



^


R1>

R1>R1>R1(config)#username cisco1 password cisco1

^


R1> ^



^


R1>

R1>

R1>enable

Password:

Password:

R1#disable

R1>

REGISTRADAS

banner motd


Username: cisco

Password:

R1>enable

Password:




R1(config-if)#

R1#

*Mar 1 00:40:09.047: %SYS-5-CONFIG_I: Configured from console by cisco on console

R1#

R1#ip address 192.168.1.1 255.255.255.0

^


R1#enable




R1(config-if)#ip address 192.168.1.1 255.255.255.0

R1(config-if)#no shut

R1(config-if)#

*Mar 1 00:43:13.567: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

*Mar 1 00:43:14.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,
changed state to up

R1(config-if)#exit

R1(config)#line console 0

R1(config-line)#logg

% Incomplete command.

R1(config-line)#logging syn

R1(config-line)#logging synchronous

R1(config-line)#interface s0

% Incomplete command.

R1(config)#interface s0/0


R1(config-if)#no shutdown

R1(config-if)#

*Mar 1 00:46:02.807: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up

R1(config-if)#

*Mar 1 00:46:03.811: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed
state to up

R1(config-if)#

state to down

R1(config-if)#

state to up

R1(config-if)#


*Mar 1 00:56:01.255: %SYS-5-CONFIG_I: Configured from console by cisco on console

Connected to Dynamips VM "R2" (ID 1, type c2691) - Console port
Press ENTER to get the prompt.

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]:

% Please answer 'yes' or 'no'.

Would you like to enter the initial configuration dialog? [yes/no]:

% Please answer 'yes' or 'no'.

Would you like to enter the initial configuration dialog? [yes/no]: n

Would you like to terminate autoinstall? [yes]:

Press RETURN to get started!

*Mar 1 00:00:04.347: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0
, changed state to up

*Mar 1 00:00:04.347: %LINEPROTO-5-UPDOWN: Line protocol on Interface IPv6-mpls,
changed state to up





*Mar 1 00:00:05.351: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0,
changed state to up

changed state to up

changed state to up

changed state to up

changed state to down



*Mar 1 00:01:14.883: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state
to administratively down

*Mar 1 00:01:15.139: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state
to administratively down


*Mar 1 00:01:15.883: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0/1, changed state to down

et0/0, changed state to down

*Mar 1 00:01:16.703: %LINK-5-CHANGED: Interface Serial0/0, changed state to
administratively down




*Mar 1 00:01:19.339: %IP-5-WEBINST_KILL: Terminating DNS process

*Mar 1 00:01:20.627: %SYS-5-RESTART: System restarted --

Cisco IOS Software, 2600 Software (C2691-ADVENTERPRISEK9-M), Version 12.4(25), R
ELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Tue 21-Apr-09 10:48 by prod_rel_team

*Mar 1 00:01:20.639: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing
a cold start

Router>y

Translating "y"...domain server (255.255.255.255)

(255.255.255.255)

Translating "y"...domain server (255.255.255.255)


Router>

Router>ena

Router#hostname R2

^


Router#configure terminal


Router(config)#hostname R2

R2(config)#



*Mar 1 00:12:29.755: %SYS-5-CONFIG_I: Configured from console by console

R2>

R2>

R2>

R2>

R2>



R2>enable



R2(config)#line console 0

R2(config-line)#logginsynchronous

R2(config-line)#interface f0/0



R2(config-if)#

*Mar 1 00:47:51.399: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t
o up

et0/0, changed state to up

R2(config-if)#interface s0/0



R2(config-if)#


R2(config-if)#

changed state to up

R2(config-if)#end

R2#

*Mar 1 00:49:16.295: %SYS-5-CONFIG_I: Configured from console by console

R2#show ipinterface brief

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 192.168.3.1 YES manual up up

Serial0/0 192.168.2.2 YES manual up up

FastEthernet0/1 unassigned YES unset administratively down down

Serial0/1 unassigned YES unset administratively down down

Serial0/2 unassigned YES unset administratively down down

Serial0/3 unassigned YE S unset administratively down down

R2#ping 192.168.2.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/13/32 ms

R2#

R2#show iproute

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C 192.168.2.0/24 is directly connected, Serial0/0

C 192.168.3.0/24 is directly connected, FastEthernet0/0

R2#

R2#telnet 192.168.2.1

Trying192.168.2.1 ... Open

REGISTRADAS

bannermotd


Password:

R1>enable

Password:

R1#show ip interface

FastEthernet0/0 is up, line protocol is up

Internet address is 192.168.1.1/24

Broadcast address is 255.255.255.255

Address determined by setup command

MTU is 1500 bytes

Helper address is not set

Directed broadcast forwarding is disabled

Outgoing access list is not set

Inbound access list is not set

Proxy ARP is enabled

Local Proxy ARP is disabled

Security level is default

Split horizon is enabled

ICMP redirects are always sent

ICMP unreachables are always sent

ICMP mask replies are never sent

IP fast switching is enabled

IP fast switching on the same interface is disabled

IP Flow switching is disabled

IP CEF switching is enabled

IP CEF Fast switching turbo vector

IP multicast fast switching is enabled

IP multicast distributed fast switching is disabled

IP route-cache flags are Fast, CEF

Router Discovery is disabled

IP output packet accounting is disabled

IP access violation accounting is disabled

TCP/IP header compression is disabled

RTP/IP header compression is disabled

Policy routing is disabled

Network address translation is disabled

BGP Policy Mapping is disabled

WCCP Redirect outbound is disabled

WCCP Redirect inbound is disabled

WCCP Redirect exclude is disabled

Serial0/0 is up, line protocol is up

Internet address is 192.168.2.1/24

Broadcast address is 255.255.255.255

Address determined by setup command

MTU is 1500 bytes

Helper address is not set

Directed broadcast forwarding is disabled

Outgoing access list is not set

Inbound access list is not set

Proxy ARP is enabled

Local Proxy ARP is disabled

Security level is default

Split horizon is enabled

ICMP redirects are always sent

ICMP unreachables are always sent

ICMP mask replies are never sent

IP fast switching is enabled

IP fast switching on the same interface is enabled

IP Flow switching is disabled

IP CEF switching is enabled

IP CEF Fast switching turbo vector

IP multicast fast switching is enabled

IP multicast distributed fast switching is disabled

IP route-cache flags are Fast, CEF

Router Discovery is disabled

IP output packet accounting is disabled

IP access violation accounting is disabled

TCP/IP header compression is disabled

RTP/IP header compression is disabled

Policy routing is disabled

Network address translation is disabled

BGP Policy Mapping is disabled

WCCP Redirect outbound is disabled

WCCP Redirect inbound is disabled

WCCP Redirect exclude is disabled

FastEthernet0/1 is administratively down, line protocol is down

Internet protocol processing disabled

Serial0/1 is administratively down, line protocol is down

Internet protocolprocessingdisabled





R1#

R1#

R1#

R1#

R1#

R1#

R1#

R1#

R1#

R1#show ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C 192.168.1.0/24 is directly connected, FastEthernet0/0

C 192.168.2.0/24 is directly connected, Serial0/0

R1#

53302372 config-gns3

Recommandé

Recommandé

Contenu connexe

Similaire à 53302372 config-gns3

Similaire à 53302372 config-gns3 (20)

Plus de Rokitta Apollonia

Plus de Rokitta Apollonia (6)

53302372 config-gns3