Recommandé
Contenu connexe
Tendances
Tendances (20)
En vedette
Similaire à Raw Material Handling in Fasteners Manufacturing Process by Rupal Jyotishi
Similaire à Raw Material Handling in Fasteners Manufacturing Process by Rupal Jyotishi (20)
Dernier
Dernier (20)
Raw Material Handling in Fasteners Manufacturing Process by Rupal Jyotishi
- 1. Fasteners Manufacturing By Rupal Jyotishi Fasteners Manufacturing Rupal Jyotishi…
- 2. Fasteners Manufacturing By Rupal Jyotishi Manufacturing process flowchart Wire Drawing Forming Threading Heat Treatment Finishing Packaging & Dispatch Bolt forming
- 3. Fasteners Manufacturing By Rupal Jyotishi Manufacturing process flowchart Nut forming Wire Drawing Forming Tapping Heat Treatment Finishing Packaging & Dispatch
- 4. Fasteners Manufacturing By Rupal Jyotishi Module 1.1 Raw Material Handling Note:- “Before starting this we need to identify few areas...”& for this I designed a “Level 1 – Technique” _write me on rupaljyotishi@gmail.com to get a copy of “Level 1-Tech” ..
- 5. Fasteners Manufacturing By Rupal Jyotishi Fastener Material.. • There is no one fastener material that is right for every environment. Selecting right material from vast array of material is important from technical and commercial perspective. • Apart from the cost and availability, careful consideration may need to be given to strength, temperature , corrosion, vibration, fatigue and many other variables.
- 6. Fasteners Manufacturing By Rupal Jyotishi Terms Used to describe the Strength of Fastener Material Are:- 1. Tensile strength 2. Yield stress 3. Proof load stress 4. Ultimate tensile stress 5. Fatigue strength 6. Tensional strength 7. Hardness 8. Ductility 9. Toughness
- 7. Fasteners Manufacturing By Rupal Jyotishi Mechanical Properties… • Tensile Strength:- is an expression of the maximum capacity of a particular material to stretch under tensile load , prior to failure. Its normally expressed in :- Pound/Tons - inch terms Kilo Newton – metric terms • Yield Stress:- is an expression of the theoretical point of stress (pressure) beyond which the material losses its elasticity and becomes permanently stretched. Its normally expressed in :- ibf/ in2 - inch term N/ mm2 - metric terms
- 8. Fasteners Manufacturing By Rupal Jyotishi • Proof Load Stress:- is an expression of the minimum stress a material must achieve, prior to permanent elongation and, the stress which would be applied to test and re-measure a specific fastener to prove it had not permanently stretched and that it will carry the required load. Its normally expressed in :- ibf/ in2 N/ mm2 Approximately between 80% and 90% of the theoretical yield stress. • Ultimate Tensile strength:- is the theoretical minimum point at which the material will fracture. It is expressed in the same terms as yield stress and proof load stress. These properties used to calculate the Proof Load and Breaking load for each diameter of each grade or class of product. Its normally expressed in :- Pounds force - inch terms Kilo Newton (KN)- metric terms Mechanical Properties…(cont.)
- 9. Fasteners Manufacturing By Rupal Jyotishi • Fatigue Strength:- is a maximum stress a fastener can withstand for a specified number of repeated cycles prior to its failure. • Torsional Strength:- is a load usually expressed in terms torque, at which fasteners fails by being twisted of about its axis. • Ductility:- is a measure of the degree of plastic deformation that has been sustained at fracture. In other words , it is the ability of material to deform before it fracture. • Toughness:- is defined as a material’s ability to absorb impact or shock loading. Impact strength toughness is rarely a specification requirement. Mechanical Properties…(cont.)
- 10. Fasteners Manufacturing By Rupal Jyotishi Stress-Strain………
- 11. Fasteners Manufacturing By Rupal Jyotishi Stress-Strain Diagram:-
- 12. Fasteners Manufacturing By Rupal Jyotishi Material used in Fasteners Manufacturing Alloy Brass Bronze Aluminum Magnesium Low carbon Stainless steel
- 13. Fasteners Manufacturing By Rupal Jyotishi Stainless steel…. • Stainless steel is a family of iron-based alloy that must contain at least 10.5% chromium . The presence of chromium creates an invisible surface film that resists oxidation and makes the material “passive” or corrosion resistant. Stainless steel can be simply and logically divided into three classes on the basis of their microstructure:- Austenitic :- * 300 series contains nickel * Not heat treatable * Strength through cold-working Martensitic :- * 400 series contains no nickel * Responds to heat treat Ferritic :- * 400 series (430)contains no nickel * Not heat treatable * Strength through cold working
- 14. Fasteners Manufacturing By Rupal Jyotishi Stainless Steel 302 • Most common grade available in HQ (with Cu) • Excellent salt spray resistance • Strength as received 75 ksi (app. 517.10 Mpa) • Work hardenable to 110 ksi (app. 758.42 Mpa ) • Becomes slightly magnetic when cold worked • Tendency to gall Note:- 1 ksi=6.89 Mpa • Common heat treatable grade used for high strength • Hardenable to range 35-45 HRC • Magnetic • Average corrosion resistance • High K factor • Similar corrosion resistance to heavy zinc plating Stainless Steel 410
- 15. Fasteners Manufacturing By Rupal Jyotishi Aluminum • Common alloys are 2024,6061 and 380 (for casting) • Tensile strength range from 45 ksi to 75 ksi • Softness can cause some heading problems (build-up vs wear) • For grade 8 fasteners consideration needs to be given to under head bearing stress to reduce embedment* • When used with stainless steel screws aluminum has a high probability of galling. • If aluminum is combined with stainless steel in a corrosive environment, the aluminum will corrode due to galvanic action. *(Embedment is a phenomenon in mechanical engineering in which the surfaces between mechanical members of a loaded joint embed)
- 16. Fasteners Manufacturing By Rupal Jyotishi Magnesium • Very good strength to weight ratio • Very low formability • High galling tendency • Tensile strength around 40ksi • Strongly attacked by galvanic corrosion.
- 17. Fasteners Manufacturing By Rupal Jyotishi Carbon Steel Majority of fasteners manufactured are out of steel. Steel is readily available, less expensive, excellent workability, offers a wide range of attainable strength properties. • Low carbon steel:- Contains less than 0.25% carbon Some are heat treatable (Generally boron based low carbon steels) Most commonly used AISI 1006-1022 • Medium Carbon Steel:- Carbon contains 0.25% to 0.60% Heat treatable Most commonly used AISI 1030,1035,1045 and 1541 • Alloy Steel:-Steel with one or more mix elements./ <2% carbon etc. Heat Treatable Most commonly used AISI 4037,4140,4135 and SCM435
- 18. Fasteners Manufacturing By Rupal Jyotishi Processes of Material Handling.. Raw material handling in a fasteners industry contains several steps before going to next operation as input. The processes are:- 1. Pre-cleaning 2. Phosphating 3. Wire drawing 4. Annealing 5. Storage by assigning color code
- 19. Fasteners Manufacturing By Rupal Jyotishi Wire Process… Input • CHQ wire • CHQ Bar Pickling • H2SO4 & HCL • Hydro Lime Drawing • By using drawing machine Annealing • To remove internal stress /increase ductility/soften the material Pickling & Coating • To remove scale (if any) and coating(phosphating) for corrosion resistance Finished lots • Send to raw material inventory by assigning colour coding
- 20. Fasteners Manufacturing By Rupal Jyotishi For detailed description of these processes, you can write an email to me on _ rupaljyotishi@gmail.com 1.Pre-cleaning 2.Phosphating 3.Wire drawing 4.Annealing 5.Storage by assigning color code Facebook:- https://www.facebook.com/fastenersmanufacturingbyRj1/
- 21. Fasteners Manufacturing By Rupal Jyotishi Thank You