6. Field Assembly Optical Connector
Features
Field assembly with simple tools
Easy and quick assembly without polishing and epoxy
Low insertion loss & reflection loss
Applications
Fiber Optic Telecommunication
Optical Fiber Distributer
Optical Cable interconnection
Fiber Distribution Frame
Connector: SC, LC, FC.
UPC/APC
Specification
Parameter FAOC
Insertion Loss Max. < 0.4dB Avg. < 0.3dB
Reflection Loss > 50 dB
Operating Temperature 20 ~ 60 °C
Storage Temperature - 40 ~ 80 °C
7. AFL Fast Connectors (Pre-Polish Connectors)
Features
Pre-stubbed, factory-polished ferrule
No epoxy required
Precision mechanical alignment insures low loss
Fiber can be reseated
3.0mm, 2.0mm, and 900μm boot provided with each connector
VFI can be used to confirm fiber is installed properly
Meets TIA/EIA 568A performance requirements
Meets TIA/EIA 604 (focis) connector interface requirements
Applications
Premise environments
Connections at the desk for LAN environments
Patch panels
Direct equipment termination
Fiber to the Subscriber (FTTx) applications
Repair/replacement requirements
Equipment test leads
Specification
Insertion Loss: Maximum: 0.5 dB, Average: 0.2 dB (SM), Average: 0.1 dB (MM)
Return Loss: Maximum: 45 dB, Average: 56.4 dB
Operating Temperature: -40 ~ +75 °C
8. Fixed Connector Attenuator
Features
• Wavelength insensitive
• Modal noise suppression
• Low polarization dependent loss
• High laser power endurance
Applications
• Telecommunication systems
• Cable television networks
• Test equipment
Specification
Attenuation (dB) PC, APC 1~30dB, 1dB Incremental
Operating wavelength (nm) 1310 and 1550
Return loss (dB) PC <-50
APC <-60
Tolerance on attenuation (dB) 1~10dB <±0.5
>10dB <±1.0
Polarization dependent loss (dB) <0.5
Operating temperature -40~+75°C
9. AFL Splice Connect (Mechanical Splice)
AFL Telecommunications’ Splice Connect is a mechanical splice that provides an inexpensive,
quick alternative to mating fibers. Using V-groove technology, this splice maintains physical
contact between the fibers. An assembly tool is used to ensure the fibers are mated correctly,
resulting in <0.1dB insertion loss (typical for single-mode).
The Splice Connect secures both fiber and coating independently with the U-shaped sleeve,
enhancing the strength against fiber twist.
Features
• Quick splicing time
• Minimal tools
• 250μm and/or 900μm fiber capabilities
• Both fiber and coating are secured independently.
Applications
• Restoration
• Premise environments
• Fiber-to-the-Subscriber (FTTx) applications
10. PLC Splitter
Description
The planar light wave circuit (PLC) splitter is wave guide device based on substrates of
quartz, silicon or other materials, which is used for power coupling and reallocation of optical
signals. It features low wavelength sensitivity, small size, high reliability, per fed splitting
uniformity. Wide wavelength range, and so on, and is especially applicable to OLT and ONT
connection and splitting of optical signals over FTTX passive optical networks.
Features
Perfect splitting uniformity
Small polarization dependent loss
High reliability and better fail failure mode
Small size, compact structure ,easy integration
Multi-channel. Large cost reduction space, facilitating batch production.
12. Outdoor FTB 2/4 fiber (TN-4FFTTH)
Descrabtion
The FTB 2/4 from TENAS Factory is rugged. low profile interconnection between central office
and multi-dwelling units of FTTx application
The design of FTB 2/4 splitter terminal combines the functionality of a local convergence
cabinet with FTB 2/4
Is multi-layer design allows installers to access only the components necessary for initial
installation or subscriber turn-up. It can house the splitter and allows for pigtail splicing of
distribution drop cables as needed.
Features
• Indoor or outdoor rated.
• You can use 1x2, 1x4, 2x4 and 1x8 splitter.
• Max. up 8 pcs of FTTH drop cable or pigtails.
• Suitable for Wall-mounting or pole mounting application
• 2pcs of inlet ports and 8x2 pcs of outlet ports
• You can use LC or SC connectors
• Dust and splash-proof: IP65
Application
• FTTH, FTTB, FTTC.
• Telecommunication network.
• CATV.
13. Outdoor FTB 12/24 fiber (TN – 24 FTTH)
Descrabtion
The FTB 12/24 from TENAS Factory is rugged. Low profile interconnection between central
office and multi-dwelling units of FTTx application
The design of FTB 12/24 splitter terminal combines the functionality of a local convergence
cabinet with FTB 12/24
Is multi-layer design allows installers to access only the components necessary for initial
installation or subscriber turn-up. It can house the splitter and allows for pigtail splicing of
distribution drop cables as needed.
Features
• Indoor or outdoor rated.
• You can use 1x4, 1x8, 1x16 splitter as well as 2x4,2x8,2x16 splitter.
• Max. up 32 pcs of FTTH drop cable or pigtails.
• Suitable for Wall-mounting or pole mounting application
• 2pcs of inlet ports and 8x2 pcs of outlet ports
• You can use LC or SC connectors
• Dust and splash-proof: IP65
Application
• FTTH, FTTB, FTTC.
• Telecommunication network.
• CATV.
14. ODB Indoor types
Description
The fiber distribution box is applicable to optical terminals. It completes the connection,
distribution and scheduling between subscriber cable and optical fiber terminals and is widely
applied to optical fiber communication network projects.
The product series are wall-mounted and easy to use and maintain.
features
Used in indoor.
Dust and splash-proof: IP55
Wall-mounted or pole-mounted, Single door, front operation
Made of high quality steel sheet, spraying for surface treatment
Applicable to pigtails 0.9mm; length: 0.5--1m
Available in FC, LC and SC connector
Protection and grounding
Perfect optical route design to ensure good bend radius of fiber
Indoor ODB 12 Fiber
16. ODF Optical Distribution Frame
Description
ODF is a modular encapsulation of Optical Splitters
in a rack mountable unit, with a patch panel for
input and output adapters.
features
Rack-mount, 19 inch (483mm) & ETSI rack.
Adjustable Distance (0/30mm) between installations.
Ear or guide ring plate and unit front cover.
Made of high-quality steel sheet, surface.
Electrostatic spray, pleasant appearance.
We can supply 24,48,72,96 and 144 fiber
17. Optical Splitter Box (OSB)
Description
Optical Splitter Box from TENAS Factory is passive optical
device that divides one input of optical power into
two or more outputs.
features
Used in indoor
Wall mounted, Single door, front facing operation
Material: high quality steel sheet, spraying for surface treatment
Optional various optical splitters
Compatible with PLC and PBT optical splitters
Applicable to pigtails of splitter: 0.9mm; length: 0.5--1m
Available in LC & simplex.
Plug-in inlet optical cable
We can supply with PLC splitter 1x16 and 1x32
18. Optical Splitter Frame (OSF)
Description
Optical Splitter Frame from TENAS Factory is passive optical device that divides
one input of optical power into two or more outputs.
OSF, 4 x 1:2, LC/APC connector
OSF, 4 x 1:4, LC/APC connector
OSF, 1:32, LC/APC connector
OSF 16 x 1:2, LC/APC connector
OSF, 8 x 1:2, LC/APC connector
OSF, 2:32, LC/APC connector
19. Fiber Optic Socket
OVERVIEW
It is the final project of FTTH access. It provides solutions to ONT (or home gateway)
installation, inlet of indoor optical cables and indoor cabling. The project involves products such
as the household information box , field connector and mechanical splice used for connection
of single-fiber drop cables, and patch cord. When the ONT (or home gateway) needs to be
installed in a box, the household information box is adopted usually. When the ONT (or home
gateway) needs to be installed on the desktop, the fiber socket is adopted usually.
Socket-outlet
Features
Independent use.
Quality polycarbonate (PC) material, with perfect fireproof performance.
Allowing storage of a small quantity of redundant fibers.
Face Plate
Features
Independent use.
Quality polycarbonate (PC) material, with perfect fireproof performance.
SC simplex or LC duplex ,
20. Fiber Optic Closure
Description
Fiber Optic Closure from TENAS Factory is specialized designed for FTTx application.
The product adopts Heat shrinkable sleeve, it can be used for straight-through
and branching-off application, as well as passive Optical fiber distribution.
GJS-01-12- 72 Fiber Optic Closure
Application
FTTH,FTTB,FTTC
Telecommunication Network
CATV
Local Area Network
GJS03A- 96—1 Fiber Optic Closure
Description
The GJS03A-96-1 from TENAS Factory
is specialized designed for FTTx application.
The product adopts Heat shrinkable sleeve,
it can be used for straight-through
and branching-off application, as well as passive
Optical fiber distribution.
21. Specification
Height: 53cm, Net Weight: 1.64kg,
Base diameter: 16cm, closet ring dia.:21cm
4 small holes +1 oval hole
The diameter of the small holes is 2.0cm.
The major axis of the oval hole(inside wall)
is 6.cm,and the shorter axis of the oval hole is 4.cm.
Application
FTTH,FTTB,FTTC
Telecommunication Network
CATV
Local Area Network
GJS03S- JF144--1 Fiber Optic Closure
Description
The GJS03S-JF144-1 from TENAS Factory
is specialized designed for FTTx application.
The product adopts Heat shrinkable sleeve,
it can be used for straight-through
and branching-off application, as well as passive
optical fiber distribution.
Specification
Weight: 1.78kg Height: 42cm
Base diameter:16cm , closet ring dia. :21cm
4 small holes +1 oval hole
The diameter of the small holes is 2.0cm.
The major axis of the oval hole(inside wall)
is 6.cm,and the shorter axis of the oval hole is 4.cm.
Application
FTTH,FTTB,FTTC
Telecommunication Network
CATV
Local Area Network
22. GJS03F-JF192Fiber Optic Closure
Description
The GJS03D-JF96 from TENAS Factory
is specialized designed for FTTx application.
The product adopts Heat shrinkable sleeve,
it can be used for straight-through and branching-off application,
as well as passive Optical fiber distribution
Specification
Weight: 1.85kg, Height: 53cm
Base diameter: 16cm, closet ring dia.:21cm
4 small holes +1 oval hole
The diameter of the small holes is 2.0cm.
The major axis of the oval hole (inside wall)
is 6.cm,and the shorter axis of the oval hole is 4.cm.
Application
FTTH,FTTB,FTTC
Telecommunication Network
CATV
Local Area Network
GJS03E-288Fiber Optic Closure
Description
The GJS03E-288 from TENAS Factory
is specialized designed for FTTx application.
The product adopts Heat shrinkable sleeve,
it can be used for straight-through
and branching-off application, as well as passive
optical fiber distribution.
23. Specification
Height: 71cm Weight:7.4kg
Base diameter:28cm closet ring
dia.:29.6cm5 small holes +1 oval hole
The diameter of the small holes is 3.3 cm.
The oval hole is the same as GJS03A
Application
FTTH,FTTB,FTTC
Telecommunication Network
CATV
Local Area Network
GPJ-04V7 Fiber Optic Splice Closure
For FAT and BF-FAT
GPJ-04V7
25. Features
Nonmetal case to effectively prevent condensation
One and Double door operation on one side
Available in splicing &termination tray
Lead-in cable trays by areas after cable fixed –stripping –protection
Available in duplex LC adapter
26. Small Form-Factor Pluggable (SFP) Transceiver
Description
Small Form-Factor Pluggable (SFP) is a compact, hot-pluggable transceiver used for both
telecommunication and data communication application. It interfaces network device mother
board (for a switch, router, media converter or similar device) to fiber optic or copper
networking cable. It is a popular industry format supported by many network component
vendors.
SFP transceivers are designed to support SONET, Gigabit Ethernet, Fiber Channel, and other
communication standards. The standard is expanding to SFP+ which will be able to support
data rates up to 10.0Gbit/s (that will include the data rates for 8gigabit Fiber channel, and
10GbE). SFP+ module versions for optical as well as copper are being introduced. In comparison
to Xenpak, X2 or XFP type of modules, SFP+ module leave some of the circuitry to be
implemented on the host board instead of inside the module.
27. Media converter types
1.
10/100/1000Base-SX/LX Smart
Application
The planet GST-80x provides advanced Media conversion technology- 10/100/1000Base-T and
SX/LX interfaces to fulfill different kinds of demand as the current network grows and
expanding. The GST-80x provides diverse fiber connect type options for different network
applications. It is very flexible for the GST-80x working as a standalone device or being installed
in the central Web Smart/Management media converter chassis for centralized management.
When working with the Web Smart/Management media converter chassis the GST-80x is hot
swappable to avoid network downtime. The GST-80 is the ideal solution for building a network
solution of FTTH or FTTC and FTTB for ISPs, campuses and enterprise.
2.
10/100Base-TX to 100Base-FX Smart
28. 3.
10/100Base-T to 100Base-SX/LX Gigabit
Application
With high performance of data transmission and easy installation, the GT-80x can build the ISP
network solution of FTTH or FTTC and FTTB, also for small office network environment of
enterprises.
4.
Managed Gigabit Ethernet
29. FURUKAWA Splicer Machine S178A
Features
Rugged and compact hand held design to endure any kind of environmental conditions
Fast splice (7 sec) at super low loss and Fast Heating (25 sec)*1200 cycles (Splicing & Heating) with 2
batteries
Available for All METRO/LAN/FTTx fibers including ultra bend-insensitive fibers (e.g.EZ-Bend™)
Applicable for Splice-on-connector(SOC) – Both Seiko Galen Connectors and Diamond Connectors available
Easy maintenance – Easy electrode replacement /mirror free alignment system
Auto-start shrink sleeve oven feature
Improved GUI to further enhance ease-of-use
Large memory for storing data(2,000 splice data) and image(100 images)
RoHS and Telcordia (GR-765-Core) compliant
Specification
Applicable fibers SMF, MMF, DSF, NZDSF, BIF/UBIF(Bend insensitive fiber)
Fibers cleave length 5 - 16 mm for 250 um fiber, 10 -16 mm for 900um tight buffer
Cladding Diameter 80 -150um
Coating Diameter 160 - 900um
Typical Insertion Loss 0.02dB for SMF, 0.01dB for MMF
( similar fiber splicing) 0.03dB for NZDSF, 0.04dB for EZ-Bend
Splice Programs Up to 150
Automatic splicing selection SM: SMF, DSF, NZDSF, BIF/UBIF(Bend insensitive fiber)
MM: MMF
Heat Program Up to 18
Auto heating start available
Dimension 127W x 199D x 105H mm (Not including shock absorber)
159W x 231D x 130 H mm (Including shock absorber)
Fiber Holding Tight Holder (Loose tube applicable)
30. or Fiber Holder System
Weight 1.9 kg (without battery), 2.3kg (with two batteries)
Splice time 7 seconds (Semi-auto mode), 9 seconds (Regular mode)
Applicable Sleeves 40/60mm
Heating time 25 seconds for 40mm and 60 mm sleeves 31 seconds
for 40mm and 60 mm sleeves (Regular mode)
Return loss >60dB
Tension Test 1.96 N
Magnification 101x, 304x or 608x
Monitor 3.5" color LCD monitor
Video output/Data interface USB 2.0
Splice memory maximum 2000 splices
Image capture capacity Last 100 images to be automatically captured + Up to 24
Display user interface GUI
Battery capacity 80 splice/heat cycles with single battery
200 splice/heat cycle with dual batteries
Displaying language 20 languages (e.g. English, Spanish, Japanese, Chinese)
Operating temperature -10 to + 50 degree C (without excessive humidity)
Storage temperature -40 to +60 degree C (without excessive humidity)
Power source AC 100 to 240V (50/60Hz), DC Input 11 to 17 V
Worktable Available
31. FURUKAWA Fiber Optic Cleaver S325A
Features
One-Step Action
Cleave Anywhere! - In Your Palm or on Your Desktop
Easy Fiber Loading
Simple Operation
High Capacity Waste Fiber Collection
Durable Design
Easy Maintenance on-Site
Specifications
Fiber Types All fiber types, single to 12-fiber ribbons
Clad Diameter 0.125mm
Dimensions/Weight 93W x 68D x 52H [mm], 330 grams
Ribbon Fiber: 10mm Fixed Length
Coating Diameter 0.25mm and 0.9mm for single fiber
Cleave Length Single Fiber: Fixed Length - 10 & 16mm
Variable Length - 3 to 20mm
32. Fiber Optic Test Equipment
1- OPTICAL TIME DOMAIN REFLECTOMETERS (OTDRs) AND FAULT LOCATORS:
OTDR from AFL with deferent models for SM or MM applications to meet all fiber optic requirements to
perform all loss measurements and fault location.AFL recently produced allots of products For FTTx
Projects like OFL280 with two deferent models to perform the construction and maintenance for FTTx
networks also this device is integrated with power meter & light source & VFL
2- OPTICAL LOSS TEST KITS:
Power meter and light source test kit from AFL for SM or MM applications to measure total losses over
the link and optical power.AFL provides deferent models depending on fiber applications.
33. 3- OPTICAL FIBER IDENTIFIERS:
Optical Fiber Identifier from AFL designed to identify the presence or absence of fiber optic signal and to
define direction of traffic and tone detection.
AFL produced OFI-FTTx to identify the presence or absence of an active Optical Network Terminal (ONT)
Thus the OFI-FTTx can verify whether a splitter pigtail at the FDH is connected to an active circuit before
it is disconnected for fault location or re-use.
4- INSPECTION MICROSCOPES AND VIDEOSCOPES:
Optical Fiber Scope from AFL is used for inspection of optical fiber connectors for scratches, dirt, or other
problems normally associated with poor transmission performance.
34. 5- FIBER OPTIC TALK SETS
FTS1 & FTS 2 Fiber Optic Talk Sets are designed for voice communication over spare fibers, and provide
full duplex, hands-free operation.
The FTS-20C, a clip-on coupler, is available for bare fiber access where terminated ends are not available.
6- VISUAL FAULT IDENTIFIER & LOCATOR (VFL)
The HiLite and VFI 2 are compact but powerful visible red laser sources designed to identify faults in fiber
optic jumper cables, distribution frames, patch panels, and splice trays.
35. 7- VARIABLE FIBER OPTIC ATTENUATORS
Provide technicians with a controlled means of attenuating or adjusting an optical signal level down from
the transmitted level. Applications include field and laboratory testing of system performance over a
range of attenuation values (network loads) and tuning and verifying performance of new transmitters
to specific networks at time of installation. AFL offers a range of attenuators providing test options to
technicians.
8- QUAD OTDR and CERTICIATION TEST KIT
The Noyes C860 QUAD Certification and OTDR Test Kit from AFL Telecommunications includes one
handheld C840 QUAD OLTS Tester and one C850 QUAD OTDR/OLTS with built-in auto test functionality.
With this kit, technicians can troubleshoot and perform both Tier 1 and Tier 2 certification tests of MM
and SM fiber networks, store results and create professional test reports.
36. 9- FIBER OPTIC LOSS & TEST SET
The OLTS 5 Optical Loss Test Set series offers end-to-end single-mode testing at either 1310/1550 nm
(OLTS 5-3 model) or 1550/1625 nm (OLTS 5-5 model).
10- FIBER OPTIC LOSS & RETURN LOSS TEST SET
The NOYES TURBOTEST 500B from AFL offers a single-mode bi-directional test solution for measuring
both optical loss and return loss. Five compact models are available featuring dual and triple wavelength
combinations. An optional digital full-duplex talk set option is available
38. • Compact fan-less Gigabit Ethernet switch with integrated power supply
• Integrated management with web-, SNMP,- and Telnet-interface
• 8x 10/100/1000Base-T, 2x SFP uplink-slots
• Data prioritization according to IEEE802.3p/Q, VLAN support
• 802.1x port-based network access control (Authentication)
• STP/RSTP according to IEEE802.1d & 802.1w
• IGMP-Snooping, bandwidth management, port mirroring
Fast Ethernet Installation Switch
Optimised compact and fanless design
• Ports
• 1x 100Base-FX fiber uplink
• 4x 10/100Base-TX Twisted Pair RJ-45 ports
• 1x 10/100Base-TX Twisted Pair RJ-45 downlink (optional)
• Power-over-Ethernet functionality on all RJ-45 ports (optional)
• Integrated network management (optional)
39.
40. Fast Ethernet Bridging Converter 10/100Base-T/100Base-FX
The Bridging Converter offers easy and cost effective media conversion from fiber optic
to copper in Fast Ethernet networks. This product family is specially designed to
minimize costs.
A special feature is the possibility to configure the Bridge in Converter mode for
applications with low latency requirements.
• Compact and cost effective design
• Robust metal housing
• Bridging (10/100) or Converter Mode (100)
• Multimode max. 2 km, Single Mode
Fast and Gigabit Ethernet Bridging Converter
• Fast Ethernet and Gigabit Ethernet converter
• Auto negotiation for speed and duplex mode
• Copper port supports auto MDI/MDIX
• Link Through function integrated
• SFP-slot for 1000Base-X
Gigabit Ethernet 8 Port Desktop Switch
With the 8 port Gigabit Ethernet switch, MICROSENS offers an universal device for
professional use in small, Medium and large networks. Based on the comprehensive
Management functionality with Web, CLI and SNMP access, the device satisfies all
demands.
The Gigabit Ethernet Switch is flexible and offers the best solution for creating and expanding
your networks. It has an integrated power supply unit and is fan-less. Additionally, the switch
offers an unbeatable price/performance ratio.