Powerful Google developer tools for immediate impact! (2023-24 C)
Paper02
1. Frequency Peaking Compensation
of the GX414 and GX424
by J. Ian Ridpath, Senior Applications Engineer, Video/Broadcast Products
APPLICATION NOTE
INTRODUCTION
In video switching applications, the crosspoint switch must The transfer function of this network is:
meet several critical specifications which include differential
1
phase, differential gain and frequency response flatness. Vo LC .......1
The GX4 family of crosspoint switches exceed broadcast Ts = =
requirements for the above specifications. For wide band- Vi s2 + s R + 1
L LC
width and high bit rate data applications, the frequency/
This transfer function has a pair of complex conjugate poles
flatness performance of these devices can be easily ex-
with
tended using information in this application note. Information 1
fo = ....... 2
presented gives the system designer two methods of fre- 2 LC
quency compensating a system using the GX414 and GX424
1 L
Video Crosspoint Switches. and Q = ....... 3
R C
The first method uses a small value series resistor placed in
the output of each device. The second method utilises the The frequency response peaks when Q >1/√2 at a frequency
frequency roll-off characteristics of the external video buffer equal to fo, but it is maximally flat when Q = 1/√2.
amplifier.
In the above equations, the capacitance C, represents the
CHARACTERISTICS OF THE GX414 AND GX424 load capacitor external to the device. With any value of C, a
value of R can be found which will make Q = 1/√2, thus
The GX414 and GX424 are bipolar video crosspoint switches flattening the response. Practically, this can be accomplished
configured as shown in Figure 1. Each analog switch has an by placing an external resistor in series with the output of the
emitter follower input, some level shifting and clamping device.
circuits and an emitter follower output. The four switch outputs
are tied together and brought out to one common pin. At In video routing or matrix switching applications, the load
frequencies above 1 MHz, the emitter follower switches nat- capacitance on the output bus is determined by how many
urally exhibit frequency response peaking. devices are connected to the bus. A typical example as
shown in Figure 3, uses five GX414s or five GX424s wired as
+Vcc a 20 x 1 matrix.
CS
IN 1
1 TO OUTPUT
BUFFER
IN
OUT 2
5 - GX414's
CS #2 3
CS 3 mA #3 CL = 4 x 15pF
#4 = 60pF
4
-VEE
5
Fig.1 Enabled Crosspoint Equivalent Circuit IN 20
The output impedance is roughly modelled as shown in Fig. Fig.3 20 x 1 Matrix
L
R VO
For any single selected crosspoint, four of the devices will be
+ 44 Ω 180 nH
disabled and one will be enabled (selected). The output
Vi
CLOAD
capacitance of a disabled device is approximately 15 pF
resulting in the total load capacitance seen by the selected
device as approximately 60 pF. Assuming stray capacitance
adds a further 5 pF to the system output, the total external
Fig.2 Output Impedance Model
510 - 39 - 00
2. Method 1. Adding Series Resistance to the Output
Using equation 3), the value of R which will cause Q to equal Precise modelling has been done yielding far more accurate
1/√2 will be; results. The effect on the frequency response of any seriescom-
R = ( √2 ) . √180 nH pensating resistor can be computer simulated using these
ohms
√65pF models. Figure 6 is an engineer-generated model of the
which yields; R = 74.4 ohms GX414 or GX424 device. This model has been simulated
using 'PSpice' (software by MicroSim Corporation) and com-
Since the equivalent series output resistance of the device is pared to measured results. A PSpice NETLIST is available on
44 Ω (as shown in Figure 2), an additional 30.4 Ω must be floppy disk from Gennum for assisting the systems engineer
added in series with the output in order to make the total and designer. The input and output impedance parameters
resistance equal to 74.4 Ω. Figure 4 shows the frequency are specified for frequencies up to 70 or 80 MHz and will
response of the above set-up along with the uncompensated produce accurate frequency response results for load ca-
response. For this graph, a 33 Ω resistor was used and a 60 pacitances between 10 pF and 100 pF.
pF load capacitor simulated the additional disabled devices.
IN 100 12 70n 12 12 76n OUT
12
2.5
50p
2.0 0.4 p 100
100 50p
RS = 0 Ω 2K 2.5p
V1 V2
1.5 CL = 60 pF 1.5 p + 20p
+ 50p
21p 14p
1.0 125 0.1p V1
40 100
2.2 p 0.998 x V2 20
0.5 1.74 M 2K 2.5p
GAIN (dB)
0
-0.5
R = 33Ω
-1.0
S Fig. 6 Engineer-generated Model of GX414 or GX424
-1.5
Figure 7 is an approximate model of a disabled crosspoint
-2.0
switch showing some of the circuit potentials and more
-2.5 importantly, the various capacitances associated with a disa-
0 10 100
bled switch.
FREQUENCY (MHz)
Fig. 4 Frequency and Uncompensated Responses
+8
With the same 33 Ω resistor in the circuit, the load capacitors
600 Ω
were changed to 47 pF and 27 pF in order to see their effects
on the frequency response. The 47pF capacitor closely V IN
+
0.65 V
simulates a 16 x 1 crosspoint circuit while the 27 pF approxi-
0.7pF 0.7pF 0.7pF
mates a 10 x 1 situation. Figure 5 shows the results of these
changes. 0.7pF
1.5pF
1.2K 2pF V OUT
2.5
+ 16pF
2.0 1.3 V
12pF
1.5
´
1.0 RS = 33 Ω
27 pF
GAIN (dB)
0.5
Fig. 7 Disabled Crosspoint Equivalent Circuit
0
47 pF
The input capacitance of a disabled switch varies with the DC
-0.5 bias voltage from 2.1 pF at -1 volt to 2.5 pF at +1.5 volts.
-1.0 Futhermore, there is a slight change in CIN between the
disabled state ( 2.2 pF at 0 volts bias ) and enabled state ( 2.0
-1.5
pF at 0 volts bias ). The slight variations would only be
-2.0
significant if the input driver source impedance is high. The
-2.5 output capacitance of the disabled chip is made up of four
0 10 100
times 0.7 pF, for the four output transistors, plus 12 pF which
FREQUENCY (MHz)
is common to all outputs, giving a total of approximately 15 pF.
Fig. 5 Frequency Responses due to a Change
of Capacitor Values
510 - 39 - 00
3. Method 2. Frequency Compensation by the Output
Buffer Stage.
The only drawback of using a series resistor to compensate for Figure 8 shows a 16 x 1 system that is set up using four GX414's
the peaking response of the GX414 and GX424 is the slight and two popular buffer amplifiers. The first is an Elantec EL-
degredation of differential phase through the switch and resis- 2020 and the second is a Signetics NE-5539. The EL-2020 is
tor. Since the outputs are eventually buffered at the bus by an a 50 MHz current feedback amplifier specifically designed for
operational amplifier or a specifically designed video buffer, it use in video applications. The NE-5539 is an ultra-wideband
seems reasonable to compensate at this point in the system. operational amplifier having an external frequency
compensation pin.
INPUTS FOUR GX414s BINARY ADDRESS
0.1 +8V DECODER
1 IN 0 14
V0 +V
2 13 A0
GND A0
3 IN 1 A 1 12 A1
V1 4
GND CS 11
5 10
V2 IN 2 OUT
6 9
GND NC
7 -V 8
V3 IN 3
4 3
0.1 A2
75 75
75 75 -8V 5 1 2
2 A3
+8V 6 74HC139 1
0.1 ENABLE
7
V4 1 IN 0 +V 14
2 GND A 0 13
V5 3 IN 1 A 1 12 LOGIC Vcc < 5V
4 11
GND CS
5 10
V6 IN 2 OUT
6
GND NC 9
V7 7
IN 3 -V 8
0.1 +8V
75 75
75 75
-8V 5 - 70pF
0.1
0.1 +8V
330 12
1 + 10
1 IN 0 14 75
V8 +V NE5539
2 GND 13 2-10pF 14
A0 - 3
3 12 7
V9 IN 1 A1 470
4 82
GND CS 11 FREQ.
V 10 5 10
IN 2 OUT COMP.
6 9
GND NC 22
7 -V 8 0.1
V 11 IN 3
75 75 0.1 -8V
75 75 100
GAIN
-8V
0.1 +8V
+8V
1 14
V 12 IN 0 +V
2 13 0.1
GND A 0
3 12
V 13 IN 1 A1 330
4 GND 11 3 7
CS + 75
5 IN 2 10 EL2020 6
V14 OUT 2
6 GND 9 2-10pF - 4
NC
7 8
V15 IN 3 -V 680
FREQ.
75 0.1 COMP.
75
75 75 330
-8V 0.1
-8V
500
GAIN
NOTES
Pin 9 is NC ( no connection - pin is floating).
Unless otherwise shown all capacitors are in µF
and all resistors are in ohms.
Fig. 8 16 x 1 Video Crosspoint Circuit
510 - 39 - 00
4. Several combinations of resistor values were used in order to adjusted to flatten the frequency response. The frequency
set the gain of each amplifier to 6 dB and yet maintain stability. response was observed and measured using the test set-up
A small trimmer capacitor in conjunction with a series resistor as shown in Figure 9.
was used as a lag-circuit at the amplifier input. Along with this
circuit, in the case of the NE-5539, a compensating trimmer Initially, the buffer amplifiers were set up having as wide a
capacitor was connected to the compensation pin. bandwidth as possible. Results approaching those shown in
the manufacturer's data book were achieved. The crosspoint
Each buffer amplifier was then independently connected to the switches were then placed in the circuit and obvious amounts
16 x 1 crosspoint circuit and the variable circuit elements were of frequency peaking were noticed.
ADDRESS 701
ADDRESS 723
HP IB ADDRESS 706
INPUT
HP3478A
HP2225A DIGITAL MULTIMETER
PRINTER
BNC CABLE CONNECTOR J1 HP59301A
HP8754A ASCII-TO-PARELLEL
NETWORK MAG/PHASE CONVERTER
ANALYZER OUTPUT
08748-60006
HP9816
DESK COMPUTER PROGRAMMING
50Ω TERMINATION CONNECTORS
8120-2883
REFERENCE
PLANE EXTENSION
CABLE PROGRAMMING
CONNECTOR
HP8748A
S-PARAMETER
DUT TEST SET
ADDRESS 707 HP8656A
SIGNAL GENERATOR
Fig. 9 Test Set-up
510 - 39 - 00