1. Tutorial 1 Surface Modeling 1
Copyright 2006 JD Mather
Inventor 11 TUTORIAL 1
Lofted Surfaces
Learning Objectives
After completing this tutorial, you will be able to:
• Construct and use surface features in solid modeling
• Incorporate surface features in part design when appropriate
• Construct Lofted surfaces
• Control point mapping when lofting
Required Competencies
Before starting this tutorial, you should have been able to:
• Construct, constraint and dimension sketches
• Project geometry on sketch planes
• Extrude sketched profiles
• Revolve sketched profiles
• Loft sketched profiles
• Understand the concepts of work and placed features
• Understand how to manipulate the history tree in the browser
Figure 1: Mold Core Insert
2. 2 Surface Modeling
The model in Figure 1 could be done with only the Inventor solids tools, but we will use
surfaces to create the solid in order to become more familiar with working with surfaces.
The Design Intent for the part is to use it as a core insert in a plastic injection mold.
1. Open the file named MOLD CORE INSERT.ipt and drag the EOP marker down
step‐by‐step and study the sketches.
Figure 2
2. Loft a surface using Sketch4 and Sketch6 as sections and select each rail in
Sketch5. (In previous versions rails had to be on separate sketches.)
Figure 3
3. Tutorial 1 Surface Modeling 3
Copyright 2006 JD Mather
3. Loft a surface using Sketch1 and Sketch7 as sections and Sketch2 and Edges1 as
rails. (Edges1 is the edge of the previous surface created and is automatically numbered in
order of pick so your number could be different.)
Figure 4
4. Loft all the remaining surfaces as shown in Figure 5.
(Remember – if you have trouble picking an edge or sketch Click to add in the dialog box.)
Figure 5
4. 4 Surface Modeling
5. Stitch the surfaces into a solid. The easiest way to pick them is select the first one in
the browser, hold down the Shift key and click on the last one. This will select all of the
surfaces in between the first and last pick.
Figure 6
6. Alternatively you could use the new Sculpt tool in Inventor 11. The advantage of
using the Sculpt tool is that the surfaces could be overlapping rather than meeting at
exact edges.
Figure 7
5. Tutorial 1 Surface Modeling 5
Copyright 2006 JD Mather
7. From the drop down analysis tools select New Draft Analysis.
Figure 8
8. Change the Style to Draft and select the y-axis as the Pull direction.
Notice the two end faces are not planar. (Tip: Each analysis is now retained in an
Analysis folder in the Browser, thus the word “New” in the command.)
Figure 9
6. 6 Surface Modeling
9. Undo back to the beginning and let’s try a different method. Loft the two end faces
as shown.
Figure 10
10. This time let’s Loft by selecting the lofted surfaces to pick all of their edges in one
pick on each face. In order to pick the surfaces you might have to move the mouse
close to an edge and wait for the select other box to come up to cycle through the
possible selections.
Figure 11
7. Tutorial 1 Surface Modeling 7
Copyright 2006 JD Mather
11. Select the rails and then click OK.
Figure 12
12. Everything looks fine but occasionally you may have to manually map the point
transitions?
Figure 13
8. 8 Surface Modeling
13. In the browser RMB on the last lofted surface and select Edit Feature. In the Loft
dialog box click on the Transitions tab and un‐check Automatic Mapping. Notice
that vectors showing the mapping of the point sets.
Figure 14
14. If it were necessary to remap a Point Set select the set and click on one of the points
in the set and then click at the location where it should be re‐mapped.
Figure 15
9. Tutorial 1 Surface Modeling 9
Copyright 2006 JD Mather
15. Undo everything and Loft a surface across the top and bottom. Try lofting between
these surfaces
Figure 16
16. Sculpt or Stitch the surfaces to a solid and make all of the sketches visible. Exercise
the model by changing some of the dimensions.
Figure 17
