Wera Screwdrivers Catalog

02 Screwdrivers
Kraftform Series 900 30
Kraftform Series 300 37
Kraftform Series Comfort 58
Kraftform Series Classic 65
Flagdriver, Stubbies 68
Accessories 70
Kraftform Micro Series 73
400 T-Handle Series 85
VDE Tools 90
Kraftform Series 100
Kraftform Kompakt VDE
Kraftform Series Comfort VDE
Kraftform Series Classic VDE
ESD Tools 113
Screwdrivers
29

32
A hexagon blade made out of
high-quality bit material extends
right through the handle – thereby
ensuring full transfer of force, even
when struck with a hammer. The
ductile tempered material prevents
the blade from splintering or
breaking.
Ever misused a screwdriver?
The Chiseldriver is the solution whenever the job requires more than just screwdriving. It is
suitable for fastening, chiselling and loosening seized screws or screw clamps. The
Wera Chiseldriver: the screwdriver you need when the going gets tough!
An integrated impact cap lengthens
the service life and reduces the
danger of splintering. Nevertheless,
always wear protective goggles.

33
The outstanding design of the
Kraftform handle that ﬁts perfectly
into the hand. Prevents hand
injuries such as blisters and
calluses. Wera Kraftform:
a synonym for "graspable"
ergonomics!
The hexagonal non-roll feature
prevents any annoying rolling
away at the workplace.
Even higher torque can be
transferred by connecting the square
drive version to a T-handle, Zyklop
ratchet or Bit Ratchet.
Greater torque can be transferred
by ﬁtting an open-jaw or ring spanner
over the integrated hex bolster.
The hard materials used for
the handle ensure rapid hand
repositioning without any danger
of the skin "sticking" to the handle.
The softer "anti-slip" zones provide
increased grip, enabling the low–
loss transfer of high forces.
Screwdrivers

?
Code mm mm mm mm mm mm
05018260002 0.6 3.5 4 80 81 9
/64
" 3 1
/8
" 10
05018262002 0.8 4.5 5 8 90 98 0.178" 3 1
/2
" 10
05018264003 1.0 5.5 6 10 100 105 7
/32
" 4" 10
05018266003 1.2 7.0 6 10 125 105 9
/32
" 5" 10
05018268002 1.6 9.0 8 13 150 112 11
/32
" 6" 10
05018270003 1.6 10.0 8 13 175 112 3
/8
" 7" 5
05018272002 2.0 12.0 10 16 200 117 1
/2
" 8" 2
05018274002 2.5 14.0 10 16 250 117 9
/16
" 10" 2
05018300002 0.8 4.5 5 8 100 98 0.178" 4 3
/64
" 10
05018301002 1.0 5.5 6 10 103 105 7
/32
" 4 1
/16
" 10
05018302002 1.2 7.0 6 10 138 105 9
/32
" 5 7
/16
" 10
Code mm mm mm mm
05017005002 PH 1 5 8 80 98 3 1
/8
" 10
05017010002 PH 2 6 10 100 105 4" 10
05017015002 PH 3 8 13 150 112 6" 5
05017020003 PH 4 10 16 200 117 8" 2
34
Kraftform Plus – Series 900
The chiseldriver for fastening and chiselling
932 A Screwdriver for slotted screws
Application: Slotted screws
Blade: Hexagonal throughout with impact cap, hexagonal bolster from
0.8 x 4.5
Design: Chrome-plated, Black Point
Handle: Kraftform with non-roll feature, multi-component, sizes
2.0 x 12.0, 2.5 x 14.0: Kraftform with non-roll feature, WeralitII,
single-component
932 AS Screwdriver for slotted screws
Blade: Hexagonal throughout, impact cap with integrated square
socket for insertion of 1
/4
" blades for higher torque, hexagonal
bolster
Handle: Kraftform with non-roll feature, multi-component
917 SPH Screwdriver for Phillips screws
Application: Phillips screws
Blade: Hexagonal throughout with impact cap, hexagonal bolster for
sizes 1 - 4
Handle: Kraftform with non-roll feature, multi-component, size 4/200:
Kraftform with non-roll feature, Weralit II, single-component
Impact cap with square drive,
directly connected to the blade
Even higher torque can be
transferred by connecting the square
drive version to a T-handle, Zyklop
ratchet or Bit Ratchet.
A screwdriver is very often misused,
in that it is struck with a hammer for
light chiselling jobs or for loosening
rusted screws. This is dangerous
because conventional screwdrivers
are not appropriate for work of that
kind – the grip and/or blade could
splinter and cause injuries. The Wera Chiseldriver has been
developed specifically for these applications. The head of the
handle is fitted with a robust, metal impact cap which is directly
connected to the hexagonal blade that extends right through the
handle. The full force of hammer blows is thereby transferred.
The special, ductile tempering of the blade prevents any
splintering and injuries. Even more force can be transferred when
screwdriving by fitting an open-jaw or ring spanner over the hex
bolster.
Can the screwdriver occasionally be
struck with a hammer?

?
?
Code mm mm mm mm
05017040002 PH 1 5 8 90 98 3 35
/64
" 10
05017041002 PH 2 6 10 113 105 4 29
/64
" 10
Code mm mm mm mm
05017050005 PZ 1 5 8 80 98 3 1
/8
" 10
05017052005 PZ 2 6 10 100 105 4" 10
05017054004 PZ 3 8 13 150 112 6" 5
05017056002 PZ 4 10 16 200 117 8" 2
Code mm mm mm mm
05024400003 TX 15 5 8 80 98 3 1
/8
" 10
05024401003 TX 20 5 8 90 98 3 1
/2
" 10
05024402003 TX 25 6 10 100 105 4" 10
05024403003 TX 27 6 10 125 105 5" 10
05024404003 TX 30 8 13 150 112 6" 10
05024405003 TX 40 8 13 150 112 6" 10
35
917 SPHS Screwdriver for Phillips
screws
Blade: Hexagonal throughout, impact cap with integrated square
/4
" blades for higher torque
918 SPZ Screwdriver for Pozidriv screws
Application: Suitable for Pozidriv*)
screws
Blade: Hexagonal throughout with impact cap, hexagonal bolster for
sizes 1 - 4
Handle: Kraftform with non-roll feature, multi-component, size 4/200:
Kraftform with non-roll feature, Weralit II, single-component
*)
Pozidriv = reg. trademark of Phillips Screw Company.
977 Screwdriver for TORX®
screws
Application: TORX®
socket screws
Blade: Hexagonal throughout with impact cap, hexagonal bolster
Wera makes its Kraftform handles from
several materials with different
properties. The core is made from a
hardwearing plastic that holds the blade
securely even when subjected to great
forces. The colour-coded soft zones of
the external mantle consist of a softer
material with more friction resistance for high torque transfer. The
black areas with a harder surface prevent the hand from sticking to
the handle enabling you to adjust your grip more quickly.
Why is the Kraftform Plus handle
made from several components?
Manual screwdriving can be quite
painful work. Wera has developed
the Kraftform handle with a shape
that ﬁts snugly in the hand. An
optimum positive ﬁt between the
hand and the handle and the choice
of materials prevent blisters, calluses
and excessive strain. You’ll notice the
difference, especially when
repositioning your hand on the handle.
How can I prevent blisters
on my hands?
Screwdrivers

Code
05018283002 1917 SPHS 1 x PH 1x90; 1 x PH 2x113
932 A 1 x 0.6x3.5x80
932 AS 1 x 0.8x4.5x100; 1 x 1.0x5.5x103;
1 x 1.2x7.0x138
Code
05024410003 1977 TORX®
1 x TX 15x80;
1 x TX 20x90; 1 x TX 25x100; 1 x TX 27x125;
1 x TX 30x150; 1 x TX 40x150
Code
05018282006 1917 SPH 1 x PH 1x80; 1 x PH 2x100
932 A 1 x 0.6x3.5x80; 1 x 0.8x4.5x90;
1 x 1.0x5.5x100; 1 x 1.2x7.0x125
36
The chiseldriver for fastening and chiselling
932 S/6 Screwdriver set Kraftform Wera:
Chiseldriver and rack
Application: Slotted and Phillips screws, impact cap with integrated square
/4
" blades for higher torque
Content: 6-piece set and rack in display carton
977/6 TORX®
Screwdriver set Kraftform Wera:
Application: TORX®
932/6 Screwdriver set Kraftform Wera:
Application: Slotted and Phillips screws

37
Kraftform Plus Series 300
Screwdrivers

38
Ever worked in a truly ergonomic manner?
Kraftform Plus prevents injuries – even long-term.
Kraftform Plus screwdrivers enable a higher transfer of force with less eﬀort and relieve
the entire hand-arm system – even with intensive use. Combined with other technical
and practical product advantages such as the Lasertip for a secure fit in the screw head,
Kraftform screwdrivers are the ideal choice for manual screwdriving jobs.

39
The basic idea for the prototype of
the Kraftform handle – that the hand
should dictate the design – has,
right through to today, proved to
be correct. In cooperation with the
internationally recognised Fraunhofer-
Institut, Wera developed a screwdriver
handle designed to match the shape
of the human hand as long ago as
the 1960s. After a long development
phase, the Wera Kraftform handle
was launched to the market in 1968.
It has been optimised through the
years with new technologies, but has
kept its proven shape. After all, the
human hand has not changed either.
The large contact area – with
particularly high friction to the soft
zones – results in high torque
transfer without any bruising
from the edges.
The Kraftform handle functions
superbly in all application situations,
and it really has to. The application
environment often does not allow any
direct tool access.
repositioning without any danger of
the skin "sticking" to the handle. The
surrounding hard zones with large
diameters glide like wheels across
the hand.
Kraftform handle that fits perfectly
into the hand prevents hand
injuries such as blisters and
calluses.
*) Pozidriv = reg. trademark of Phillips Screw Company.
Wera Lasertip "bites" itself into the
screw head and prevents any slips
out of the recess.
It can be used for slotted, Phillips and
Pozidriv*)
screws.
Screwdrivers

40
A precisely-focused laser creates a
sharp-edged surface structure.
This laser treatment results in an
edge hardness of up to 1000 HV 0.3.
prevents any rolling away at the
workplace.
The Wera TORX®
HF profile (HF =
Holding Function) securely holds
TORX®
screws on the tool tip thanks
to its drive geometry and the wedging
forces associated with this. Ideal
for work in difficult-to-access areas
e.g. screw connections in deep blind
holes.
The screw symbol and tip size
identification markings on the handle
make it easier to find the right
screwdriver in the tool case or at the
workplace.
Wera Lasertip reduces the contact
pressure required and enhances
force transfer - meaning less
screwdriving effort is required.
Screwdriving becomes safer and
easier.
The Wera Hex-Plus profile with
its improved geometry prevents
damage to the heads of hexagonal
socket screws. A higher torque
transfer of up to 20 % is possible.
This also makes screwdriving safer
and more convenient.

41
Lasertip is also ideal for oily and
greasy applications, circumstances
that would otherwise favour the
slipping out of the tool from the
screw.
The screwdriver sets are always
supplied with a wall-mountable rack.
This ensures organised storage
and quick access. The rack is also
available as an individual item.
Screwdrivers

?
Code mm mm mm mm mm
05008006002 1)
0.4 2.0 60 70 2.5 5
/64
" 2 3
/8
" 10
05110000004 1)
0.4 2.5 60 70 2.5 3
/32
" 2 3
/8
" 10
05008007003 1)
0.4 2.5 75 70 2.5 3
/32
" 3" 10
05008008002 1)
0.5 3.0 150 81 4.0 1
/8
" 6" 10
05008009002 1)
0.5 3.0 200 81 4.0 1
/8
" 8" 5
05110001004 1)
0.5 3.0 80 81 3.0 1
/8
" 3 1
/8
" 10
05008015003 0.6 3.5 100 81 3.5 9
/64
" 4" 10
05110002002 0.6 3.5 125 81 3.5 9
/64
" 5" 10
05110003002 0.6 3.5 200 81 3.5 9
/64
" 8" 5
05110004004 0.8 4.0 100 98 4.0 5
/32
" 4" 10
05110005002 0.8 4.0 150 98 4.0 5
/32
" 6" 10
05110006002 0.8 4.0 200 98 4.0 5
/32
" 8" 5
05008027004 1)
0.8 4.0 300 98 4.0 5
/32
" 12" 2
05110007003 1.0 5.5 125 98 5.5 7
/32
" 5" 10
05008055002 1.0 5.5 150 98 5.5 7
/32
" 6" 10
05110008002 1.0 5.5 200 98 5.5 7
/32
" 8" 5
05008060002 1)
1.0 5.5 300 98 5.5 7
/32
" 12" 2
05008061002 1.2 6.0 100 105 6.0 5
/16
" 4" 10
Code mm mm mm mm mm
05007610002 0.8 5.0 100 98 5.0 3
/16
" 4" 10
05007620002 1.0 6.0 125 105 6.0 1
/4
" 5" 10
05340330003 1.0 6.0 150 105 6.0 1
/4
" 6" 10
05110010003 1.2 6.5 150 105 6.0 1
/4
" 6" 10
05007635002 1.2 7.0 150 105 7.0 9
/32
" 6" 10
05007621002 1.2 6.5 200 105 7.0 9
/32
" 8" 5
05110011005 1.2 8.0 175 112 7.0 5
/16
" 7" 5
05007640002 1.6 8.0 175 112 7.0 5
/16
" 7" 5
05110104004 1.6 10.0 200 112 9.0 3
/8
" 8" 5
05110105003 1)
2.0 12.0 250 117 10.0 1
/2
" 10" 2
05018274001 2.5 14.0 250 117 16.0 9
/16
" 10" 2
05007670003 0.6 3.5 4 - 75 81 9
/64
" 3" 10
05007671003 0.8 4.0 4 - 90 81 5
/32
" 3 1
/2
" 10
05007672002 0.8 4.5 5 8 90 98 0.178" 3 1
/2
" 10
05007673003 1.0 5.5 6 10 100 98 7
/32
" 4" 10
05007674002 1.2 6.5 6 10 125 105 1
/4
" 5" 10
05007675003 1.2 7.0 6 10 125 105 9
/32
" 5" 10
05007676003 1.6 9.0 8 13 150 112 11
/32
" 6" 10
05007677002 1.6 10.0 8 13 175 112 3
/8
" 7" 5
42
It happens time and time again that
the tip slips out of the screw head
when screwdriving, sometimes
damaging valuable surfaces or
even causing injury. The tips of
the Wera Lasertip screwdrivers are
microscopically roughened by means
of a laser. This rough surface literally "bites" itself firmly into the
screw head. Slipping out becomes a thing of the past.
How to prevent the screwdriver
from slipping out of the screw
head
The right tool for every application
335 Screwdriver for slotted screws
Blade: Round
Design: Chrome-plated, Lasertip
1)
without Lasertip
Blade: Round
Handle: Kraftform with non-roll feature, multi-component, sizes 2.0
x 12.0, 2.5 x 14.0: Kraftform with non-roll feature, Weralit II,
single-component
1)
without Lasertip
334 SK Screwdriver for slotted screws
Blade: Hexagonal with bolster from 0.8 x 4.5

?
Code mm mm mm mm mm
05008069002 0.4 2.5 75 98 2.5 5
/64
" 3" 10
05008070002 0.6 3.5 100 81 3.5 9
/64
" 4" 10
05008075002 0.8 4.0 100 98 4.0 5
/32
" 4" 10
05008080002 1.0 5.5 150 98 5.5 7
/32
" 6" 10
Code mm mm mm
05008705004 1)
PH 0 60 81 3.0 2 3
/8
" 5
05008706002 1)
PH 0 100 81 3.0 4" 5
05008710003 PH 1 80 98 4.5 3 1
/8
" 10
05008712003 PH 1 200 98 4.5 8" 2
05008715002 1)
PH 1 300 98 4.5 12" 2
05008720003 PH 2 100 105 6.0 4" 10
05008723002 PH 2 150 105 6.0 6" 10
05008725002 PH 2 200 105 6.0 8" 2
05008730006 1)
PH 2 300 105 6.0 12" 2
05008735003 PH 3 150 112 8.0 6" 5
05008740002 1)
PH 4 200 112 10.0 8" 2
Code mm mm mm mm
05008750003 1)
PH 0 4 60 81 2 3
/8
" 5
05008751003 PH 1 5 8 80 98 3 1
/8
" 10
05008752003 PH 2 6 10 100 105 4" 10
05008753002 PH 3 8 13 150 112 6" 5
43
Wera makes its Kraftform handles
from several materials with different
hardwearing plastic that holds the
blade securely even when subjected
to great forces. The colour-coded
soft zones of the external mantle
consist of a softer material with more friction resistance for high
torque transfer. The black areas with a harder surface prevent
the hand from sticking to the handle enabling you to adjust your
grip more quickly.
335 FK Screwdriver for slotted screws
Application: Actuating tool for spring-loaded terminal blocks in switch
cabinet construction
Blade: Round
350 PH Screwdriver for Phillips screws
Blade: Round
1)
without Lasertip
350 SK PH Screwdriver for Phillips screws
Blade: Hexagonal, sizes 1 - 3 with bolster
1)
without Lasertip
Screwdrivers

Code
05073700002 31441 2 x 4.5 - 6.0x41.0
350 PH 1 x PH 1x80; 1 x PH 2x100
44
350 PH1/2 + 1441 SB
Application: Attachment with holding function for screws, holds all screw
profiles and sizes securely on the tool, suitable for round and
hexagon blades with a diameter from 4.5 mm to 6 mm
Design: Elastomer
Push the screw gripper onto the tip
of the screwdriver until the end of the
blade protrudes from the rubber blade
holder.
Attach the screw to the tip of the
blade and secure it in the screw
gripper.
Pull the screw gripper towards the
screwdriver handle until the two
arms of the gripper sit against the
head of the screw and are spread
slightly apart. The Wera screw gripper
releases the screw automatically after
it has been fastened.
The two gripper arms spread further
apart as they are pushed against the
surface and automatically snap
back when the head of the screw is
countersunk.
When fastening screws in blind holes
the screw gripper is pushed back,
making it possible to reach even
deep-seated screws.
And this is how the gripper works:

Code mm mm mm
05009305003 1)
PZ 0 60 81 3.0 2 3
/8
" 10
05009310003 PZ 1 80 98 4.5 3 1
/8
" 10
05009312002 PZ 1 200 98 4.5 8" 2
05009313002 1)
PZ 1 300 98 4.5 12" 2
05009315003 PZ 2 100 105 6.0 4" 10
05009317002 PZ 2 200 105 6.0 8" 2
05347743002 PZ 2 250 105 6.0 10" 2
05009319002 1)
PZ 2 300 105 6.0 12" 2
05009320002 PZ 3 150 112 8.0 6" 5
05009325002 1)
PZ 4 200 112 10.0 8" 2
Code mm mm mm mm
05009340002 1)
PZ 0 4 60 81 2 3
/8
" 5
05009341003 PZ 1 5 8 80 98 3 1
/8
" 10
05009342003 PZ 2 6 10 100 105 4" 10
05009343002 PZ 3 8 13 150 112 6" 5
Code
05073701002 31441 2 x 4.5 - 6.0x41.0
355 PZ 1 x PZ 1x80; 1 x PZ 2x100
45
355 PZ Screwdriver for Pozidriv screws
screws
Blade: Round
1)
without Lasertip
*)
355 SK PZ Screwdriver for Pozidriv screws
screws
1)
without Lasertip
*)
355 PZ1/2 + 1441 SB
profiles and sizes securely on the tool, suitable for round and
hexagon blades with a diameter from 4.5 mm to 6 mm
Design: Elastomer
Screwdrivers
Individual grippers please see page 72, 360.

?
Code mm mm mm mm
05023105002 2.0 75 70 3.0 3" 5
05023107002 2.5 75 81 3.0 3" 10
05023110003 3.0 75 81 4.0 3" 10
05023115003 4.0 75 98 5.0 3" 10
05023120003 5.0 80 105 6.0 3 1
/8
" 10
05023125004 6.0 80 105 7.0 3 1
/8
" 5
05023130004 8.0 100 112 10.0 4" 5
05023135002 10.0 100 112 12.0 4" 5
Code mm mm mm
05022795005 1.5 60 70 2 3
/8
" 10
05022800004 2.0 100 70 4" 10
05138070003 2.5 100 81 4" 10
05022805005 3.0 100 81 4" 10
05022810006 4.0 100 98 4" 10
05022815005 5.0 100 105 4" 10
05022820005 6.0 125 105 5" 5
05022825005 8.0 150 112 6" 5
05022830004 10.0 150 112 6" 5
05022835003 12.0 150 117 6" 5
05022905002 5
/32
" 100 98 4" 5
05022910002 3
/16
" 100 105 4" 5
05022915002 7
/32
" 100 105 4" 5
05022920002 1
/4
" 125 105 5" 5
05022925002 5
/16
" 150 112 6" 5
05022930002 3
/8
" 150 112 6" 5
05022935002 1
/2
" 150 117 6" 5
46
The spherical drive profile means
that it is possible to swivel the axis
of the tool to that of the screw,
and therefore enable angled,
"around-the-corner" screwdriving
jobs. This ball tip geometry – often
found on L-keys – is now available
on a number of Wera bits.
TORX®
ball tip and hexagon ball tip
Hexagon socket screws are a
problem, because the contact
surfaces that transfer the force of
the tool to the screw are very
narrow. The consequence: the head
of the screw can be damaged,
usually rounding out the recess.
Hex-Plus tools have larger contact surfaces to prevent this,
driving from the ﬂats of the recess, rather than the corners. Good
to know: Hex-Plus tools fit into every standard hexagon socket
screw!
How to prevent rounded screw
heads with Hex-Plus
354 Screwdriver for hexagon socket screws
Application: Hexagon socket screws
Blade: Round
Design: Hex-Plus, chrome-plated
352 Ball end screwdriver for hexagon socket screws
Blade: Hexagonal
Design: Ball end hexagon, chrome-plated, Black Point
Handle: Kraftform with non-roll feature, multi-component, sizes W/F
12.0, W/F 1
/2
": Kraftform with non-roll feature, Weralit II, single-
component

?
Code mm mm mm
05028048003 TX 8 60 81 3.5 2 3
/8
" 10
05028049003 TX 9 60 81 4.0 2 3
/8
" 10
05028050004 TX 10 80 81 4.0 3 1
/8
" 10
05028051004 TX 15 80 98 4.0 3 1
/8
" 10
05028052004 TX 20 100 98 4.5 4" 10
05028053004 TX 25 100 105 5.0 4" 10
05028054002 TX 27 115 105 5.5 4 9
/16
" 10
05028055004 TX 30 115 105 6.0 4 9
/16
" 10
05028056002 TX 40 130 112 7.0 5 3
/16
" 10
Code mm mm mm
05028070002 TX 20 300 98 4.5 12" 4
05028071002 TX 25 300 105 6.0 12" 4
05028072002 TX 27 300 105 6.0 12" 4
05028073002 TX 30 300 105 6.0 12" 4
Code mm mm mm
05028000003 TX 5 60 70 3.5 2 3
/8
" 10
05028001003 TX 6 60 70 3.5 2 3
/8
" 10
05028002003 TX 7 60 70 3.5 2 3
/8
" 10
05028003003 TX 8 60 81 3.5 2 3
/8
" 10
05028004003 TX 9 60 81 4.0 2 3
/8
" 10
05028005004 TX 10 80 81 4.0 3 1
/8
" 10
05028008004 TX 15 80 98 4.0 3 1
/8
" 10
05028010004 TX 20 100 98 4.5 4" 10
05028012004 TX 25 100 105 5.0 4" 10
05028013004 TX 27 115 105 5.5 4 9
/16
" 10
05028015004 TX 30 115 105 6.0 4 9
/16
" 10
05028020005 TX 40 130 112 7.0 5 1
/8
" 10
05028025004 TX 45 130 112 8.0 5 1
/8
" 10
47
In tight assembly or disassembly
situations, for example in engine
compartments, it is not possible to
securely hold the screw with the
hand on the screwdriver, and the
screw subsequently often gets lost.
Lengthy searches or the loss of the
screw (with the associated danger that could bring about) are
the consequence. The TORX®
HF tools developed by Wera are
ideal because they feature an optimised geometry of the original
TORX®
profile. The wedging forces resulting from the surface
pressure between the drive tip and the screw profile mean that
the screw is securely held on the tool!
What is the purpose of the TORX®
HF proﬁle?
367 TORX®
HF screwdriver with holding function for
TORX®
screws
Application: TORX®
socket screws
Blade: Round
Design: Holding function for TORX®
screws made according to Acument
Intellectual Properties specifications, chrome-plated
367 TORX®
HF screwdriver with holding function for
TORX®
screws
Application: TORX®
socket screws
Blade: Round
Intellectual Properties specifications, chrome-plated, extra long
blade to enable work on low-down, diﬃcult to access screws
367 TORX®
screwdriver for TORX®
screws
Application: TORX®
socket screws
Blade: Round
Screwdrivers

?
Code mm mm mm
05027950004 TX 15 80 98 4.0 3 1
/8
" 5
05027952004 TX 20 100 98 4.5 4" 5
05027954005 TX 25 100 105 5.0 4" 5
05027956004 TX 27 115 105 5.5 4 9
/16
" 5
05027958004 TX 30 115 105 6.0 4 9
/16
" 5
05027960003 TX 40 130 112 7.0 5 3
/16
" 5
05027962002 TX 45 130 112 8.0 5 3
/16
" 5
Code mm mm mm
05138257002 TX 7 60 70 3.5 2 3
/8
" 5
05138258002 TX 8 60 81 3.5 2 3
/8
" 5
05138259002 TX 9 60 81 4.0 2 3
/8
" 5
05138267002 TX 9 300 81 4.0 12" 5
05138260002 TX 10 80 81 4.0 3 1
/8
" 5
05138268002 TX 10 300 81 4.0 12" 5
05138261004 TX 15 80 98 4.0 3 1
/8
" 5
05138269002 TX 15 300 98 4.0 12" 2
05138262004 TX 20 100 98 4.5 4" 5
05138270002 TX 20 300 98 4.5 12" 2
05138263002 TX 25 100 105 5.0 4" 5
05138264002 TX 27 115 105 5.5 4 9
/16
" 5
05138265002 TX 30 115 105 6.0 4 9
/16
" 5
05138266002 TX 40 130 112 7.0 5 3
/16
" 5
Code mm mm mm
05028029003 5 IP 60 70 3.5 2 3
/8
" 5
05028030003 6 IP 60 70 3.5 2 3
/8
" 5
05028031003 7 IP 60 70 3.5 2 3
/8
" 5
05028032003 8 IP 60 70 3.5 2 3
/8
" 5
05028033003 9 IP 60 81 4.0 2 3
/8
" 5
05028034003 10 IP 80 81 4.0 3 1
/8
" 5
05028035003 15 IP 80 98 4.0 3 1
/8
" 5
05028036003 20 IP 100 98 4.5 4" 5
05028037003 25 IP 100 105 5.0 4" 5
05028028002 27 IP 115 105 5.5 4 9
/16
" 5
05028038003 30 IP 115 105 6.0 4 9
/16
" 5
05028039002 40 IP 130 112 7.0 5 3
/16
" 5
48
TORX®
tools with a borehole prevent
the unauthorised unfastening of safety
screws. The screws contain a pin that
protrudes into the drive proﬁle so that
"normal" TORX®
tools cannot be used.
This pin ﬁts into the borehole of TORX®
BO tools allowing safety screws to be
unfastened.
TORX®
with borehole
367 K Ball end TORX®
screws
Application: TORX®
socket screws
Blade: Round
Design: Ball end, chrome-plated, Black Point
367 TORX®
BO screwdriver for tamper-proof TORX®
screws
Application: TORX®
screws with safety pin
(BO = with bore hole)
Blade: Round
Design: Bore hole in TORX®
section, chrome-plated, Black Point
367 TORX PLUS®
screwdriver for TORX PLUS®
screws
Application: TORX PLUS®
socket screws
Blade: Round

TORX®
Code mm mm mm mm
05028130002 6 80 98 4.5 3 1
/8
" 5
05028132002 8 100 105 6.0 4" 5
05028134002 10 100 105 6.0 4" 5
05028136002 1
/4
" 125 112 8.0 5" 5
Code mm mm mm
05117680003 # 00 60 81 3.5 2 3
/8
" 5
05117681003 # 0 60 81 4.0 2 3
/8
" 5
05117682003 # 1 80 98 4.5 3 1
/8
" 5
05117683003 # 1 200 98 4.5 8" 5
05117684003 # 2 100 105 6.0 4" 5
05117685003 # 2 200 105 6.0 8" 5
05117691003 # 2 300 105 6.0 12" 2
05117686003 # 3 150 112 8.0 6" 5
05117687004 # 4 200 112 8.0 8" 5
05117688002 # 01 25 54 4.5 1" 5
05117689002 # 02 25 54 6.0 1" 5
? WeraTORQ-SET®
Mplus
TORQ-SET®
49
Compared with the "normal" TORX®
profile, the elliptical instead of
circular profile enlarges the 6 flanks that transfer torque between
the tool and the screw. This means that the force applied when
screwdriving is spread across a larger surface area. Higher torque
is transferred and, in addition, the service life of the screw and tool
are lengthened. The so-called centre-lock screws on cutting tools
represent a typical use of this type of screw profile. The thermal
influences on such holders for carbide insert tips often "bake"
the retaining screws so firmly that it is important to have a profile
that considerably enhances the loosening torque capability of the
screws. For this reason a torque-stable screw profile is necessary
to avoid any possible damage to the screw and to exclude the
possibility of an otherwise costly machine downtime.
TORX PLUS®
371 TORQ-SET®
Mplus screwdriver for TORQ-SET®
screws
Application: TORQ-SET®
screws
Blade: Round
Design: Mplus for higher breaking torque and longer service life,
chrome-plated
368 Screwdriver for square socket head screws
Application: Square socket screws
Blade: Round
Design: Chrome-plated, Black Point except for sizes 01+02
Handle: Kraftform with non-roll feature, multi-component, # 2/300,
# 01/25, # 02/25: Weralit II, single-component
Wera developed the Mplus profile with stronger flanks compared
with tools with a conventional TORQ-SET®
profile. This results in
approximately 70 % extra torsional strength and greatly extends
the service life of Wera Mplus tools.
How can I prevent frequent
breakages of TORQ-SET®
bits?
Screwdrivers

Code mm mm mm
05028116003 0 80 81 3.5 3 1
/8
" 5
05028118003 1 80 81 3.5 3 1
/8
" 5
05028120004 2 80 98 4.5 3 1
/8
" 5
05028122004 3 80 98 4.5 3 1
/8
" 5
05028124004 4 100 98 6.0 4" 5
05028126003 5 100 98 6.0 4" 5
Code mm mm mm mm
05029460002 5.0 70 98 7.2 2 25
/32
" 5
05029461002 5.5 70 98 7.2 2 25
/32
" 5
05029462002 6.0 70 98 7.2 2 25
/32
" 5
05029463002 7.0 80 105 7.2 3 5
/32
" 5
05029464002 8.0 80 105 9.3 3 5
/32
" 5
05029465002 10.0 80 112 9.3 3 5
/32
" 5
05029466002 13.0 80 112 11.0 3 5
/32
" 5
Code mm mm mm
05029501002 3
/16
" 70 98 7.2 2 25
/32
" 5
05029502002 1
/4
" 70 98 7.2 2 25
/32
" 5
05029503002 5
/16
" 80 105 9.3 3 5
/32
" 5
05029504004 11
/32
" 80 105 9.3 3 5
/32
" 5
05029505002 3
/8
" 80 112 9.3 3 5
/32
" 5
05029506002 7
/16
" 80 112 11.0 3 5
/32
" 5
05029507002 1
/2
" 80 112 11.0 3 5
/32
" 5
?
50
375 TRI-WING®
screwdriver for TRI-WING®
screws
Application: TRI-WING®
screws
Blade: Round
395 HO Nutdriver
Application: Hexagon headed bolts, screws and nuts
Blade: Round
Design: Hollow shaft for protruding threaded rods, chrome-plated
TIP: The hollow shaft enables seized screws or those on long
threads to be tightened and loosened
395 HO Nutdriver, imperial
Blade: Round
Design: Chrome-plated, hollow shaft for protruding threaded rods
A screwdriver with a hollow shaft is
needed whenever there are
screwdriving jobs involving threaded
rods i.e. the threaded rod through the
nut can slip into the hollow shaft of the
screwdriver.
What is the purpose of a
screwdriver with hollow shaft?

Code
05105650006 1334 1 x 1.2x6.5x150
335 1 x 0.5x3.0x80 1)
; 1 x 0.8x4.0x100;
1 x 1.0x5.5x125
350 PH 1 x PH 1x80; 1 x PH 2x100
Code
05007680003 1334 SK 1 x 0.6x3.5x75; 1 x 0.8x4.0x90;
1 x 1.0x5.5x100; 1 x 1.2x6.5x125
350 SK PH 1 x PH 1x80; 1 x PH 2x100
Code
05346278001 1334 1 x 1.2x6.5x150
334 SK 1 x 1.2x6.5x125
335 1 x 0.5x3.0x80 1)
; 1 x 1.0x5.5x150;
1 x 1.2x6.0x100
350 PH 1 x PH 1x80; 1 x PH 2x100
?
51
334/6 Rack screwdriver set Kraftform Plus
Lasertip + rack
Lasertip round blades and rack
1)
without Lasertip
334 SK/6 Rack screwdriver set Kraftform Plus
Lasertip + rack
Lasertip hexagon blades and rack
334/335/350/7 Rack screwdriver set Kraftform Plus
Lasertip + rack
Lasertip round blades + rack
1)
without Lasertip
Hexagon
Wera makes its Kraftform handles
from several materials with different
hardwearing plastic that holds the
blade securely even when subjected
to great forces. The colour-coded
soft zones of the external mantle
consist of a softer material with more friction resistance for high
torque transfer. The black areas with a harder surface prevent
the hand from sticking to the handle enabling you to adjust your
grip more quickly.
Screwdrivers

Code
05346300001 1350 PH 1 x PH 1x80; 1 x PH 2x100; 1 x PH 3x150;
1 x PH 4x200 1)
Stubby PH 1 x PH 02x25
Code
05346301001 1355 PZ 1 x PZ 1x80; 1 x PZ 2x100; 1 x PZ 3x150;
1 x PZ 4x200 1)
Stubby PZ 1 x PZ 02x25
Code
05346302001 1334 1 x 0.8x5.0x100; 1 x 1.2x6.5x150;
1 x 1.2x8.0x175; 1 x 1.6x10.0x200
336 Stubby 1 x 1.2x6.5x25
Code
05347901001 1334 1 x 1.2x6.5x150
335 1 x 0.4x2.5x60 1)
; 1 x 0.5x3.0x80 1)
;
1x0.6x3.5x100;1x0.8x4.0x100;1x1.0x5.5x125
350 PH 1 x PH 0x60 1)
; 1 x PH 1x80; 1 x PH 2x100;
1 x PH 3x150
368 1 x # 1x80; 1 x # 2x100
52
350/5 Screwdriver set Kraftform Plus Lasertip
Content: 5-piece set
1)
without Lasertip
355/5 Screwdriver set Kraftform Plus Lasertip
Application: Pozidriv*) screws
1)
without Lasertip
*)
334/336/5 Screwdriver set Kraftform Plus Lasertip
334/368/12 screwdriver set Kraftform Plus
Application: Slotted, Phillips-Recess and square socket screws
1)
without Lasertip

Code
05347778001 1334 1 x 1.2x6.5x150
335 1 x 0.8x4.0x100
350 PH 1 x PH 1x80; 1 x PH 2x100
368 1 x # 1x80; 1 x # 2x100
Code
05223161002 1367 TORX®
HF 1 x TX 8x60; 1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 27x115; 1 x TX 30x115
Code
05345221001 1367 TORX®
HF 1 x TX 8x60;
1 x TX 10x80; 1 x TX 15x80; 1 x TX 20x100;
1 x TX 25x100; 1 x TX 30x115
Code
05028059003 1367 TORX®
HF 1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 30x115; 1 x TX 40x130
53
334/368/6 Screwdriver set + rack
Application: Slotted, Phillips and square-head screws
367/7 TORX®
HF Kraftform Plus screwdriver set with
holding function and rack
Application: TORX®
367/6 TORX®
holding function
Application: TORX®
367/6 TORX®
holding function and rack
Application: TORX®
Screwdrivers

?
Code
05028074002 1367 TORX HF L 1 x TX 20x300; 1 x TX 25x300;
1 x TX 27x300; 1 x TX 30x300
Code
05028062004 1367 TORX®
1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 30x115; 1 x TX 40x130
Code
05345220001 1367 TORX®
1 x TX 10x80; 1 x TX 15x80; 1 x TX 20x100;
1 x TX 25x100; 1 x TX 30x115
54
In tight assembly or disassembly
situations, for example in engine
compartments, it is not possible to
securely hold the screw with the hand
on the screwdriver, and the screw
subsequently often gets lost. Lengthy
searches or the loss of the screw (with
the associated danger that could bring about) are the consequence.
The TORX®
HF tools developed by Wera are ideal because they
feature an optimised geometry of the original TORX®
profile. The
wedging forces resulting from the surface pressure between the
drive tip and the screw profile mean that the screw is securely held
on the tool!
What is the purpose of the TORX®
HF proﬁle?
367/4 TORX®
holding function and 300 mm-long blades
Application: TORX®
with holding function, extra long (300 mm) blade
367/6 Screwdriver set Kraftform Plus TORX®
and rack
Application: TORX®
367/5 Screwdriver set Kraftform Plus TORX®
Application: TORX®

Code
05138250004 1367 TORX®
BO 1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 30x115; 1 x TX 40x130
Code
05345223001 1367 TORX
PLUS®
1 x 8 IPx60; 1 x 10 IPx80;
1 x 15 IPx80; 1 x 20 IPx100; 1 x 25 IPx100;
1 x 30 IPx115; 1 x 40 IPx130
TORX®
Code
05345222001 1367 TORX
PLUS®
1 x 6 IPx60; 1 x 7 IPx60; 1 x 8 IPx60;
1 x 9 IPx60; 1 x 10 IPx80; 1 x 15 IPx80
55
367/6 TORX®
BO Kraftform Plus TORX®
screwdriver set and rack
Application: TORX®
screws with safety pin (BO = with bore hole)
367/7 IP Screwdriver set Kraftform Plus TORX PLUS®
Compared with the "normal" TORX®
profile, the elliptical instead of
circular profile enlarges the 6 ﬂanks that transfer torque between
the tool and the screw. This means that the force applied when
screwdriving is spread across a larger surface area. Higher torque
is transferred and, in addition, the service life of the screw and tool
are lengthened. The so-called centre-lock screws on cutting tools
represent a typical use of this type of screw profile. The thermal
inﬂuences on such holders for carbide insert tips often "bake"
the retaining screws so firmly that it is important to have a profile
that considerably enhances the loosening torque capability of the
screws. For this reason a torque-stable screw profile is necessary
to avoid any possible damage to the screw and to exclude the
possibility of an otherwise costly machine downtime.
TORX PLUS®
367/6 IP Screwdriver set Kraftform Plus TORX PLUS®
Screwdrivers

?
Code
05029510002 1395 HO 1 x 5.0x70; 1 x 5.5x70; 1 x 6.0x70;
1 x 7.0x80; 1 x 8.0x80; 1 x 10.0x80;
1 x 13.0x80
Code
05345230001 1395 HO Inch 1 x 3/16"x70; 1 x 1/4"x70; 1 x 5/16"x80;
1 x 11/32"x80; 1 x 3/8"x80; 1 x 7/16"x80;
1 x 1/2"x80
Code
05029508002 1395 HO Inch 1 x 3/16"x70; 1 x 1/4"x70; 1 x 5/16"x80;
1 x 3/8"x80; 1 x 7/16"x80; 1 x 1/2"x80
56
A screwdriver with a hollow shaft
is needed whenever there are
screwdriving jobs involving
threaded rods i.e. the threaded
rod through the nut can slip into the
hollow shaft of the screwdriver.
What is the purpose of a
screwdriver with hollow shaft?
395 HO/7 SM Nutdriver set
Content: 7-piece set in display carton
395 HO/7 SZ Nutdriver Set
395 HO/6 SZ Nutdriver Set

Code
05051010003 1160 i VDE 1 x 0.4x2.5x80 1)
; 1 x 0.6x3.5x100
247 1 x 0.5x3.0x70
334 1 x 1.2x6.5x150
335 1 x 0.8x4.0x100; 1 x 1.0x5.5x125
350 PH 1 x PH 1x80; 1 x PH 2x100
355 PZ 1 x PZ 1x80; 1 x PZ 2x100
932 A 1 x 1.0x5.5x100; 1 x 1.2x7.0x125
Rack 2 x 190.0x50,0
Code
05347105001 1160 i VDE 1 x 0.4x2.5x80 1)
; 1 x 0.6x3.5x100
247 1 x 0.5x3.0x70
334 1 x 1.2x6.5x150
335 1 x 0.8x4.0x100; 1 x 1.0x5.5x125
350 PH 1 x PH 1x80; 1 x PH 2x100
368 1 x # 1x80; 1 x # 2x100
932 A 1 x 1.0x5.5x100; 1 x 1.2x7.0x125
Rack 2 x 190.0x50,0
Code
05030005002 10
57
Kraftform XXL
12-piece screwdriver set for all-round applications
1)
without Lasertip
Kraftform XXL 2
12-piece screwdriver set for all-round applications
1)
without Lasertip
With original Kraftform handle
Bottle opener
Screwdrivers

The multi-component Kraftform
handle for quick and low-exertion
working.
identification markings on the handle
screwdriver in the tool case, or at the
workplace.
away.
The bit material used for
manufacturing is subjected to a
specific Wera hardening process,
and this ensures longer product
service life.
The Wera Black Point tip and a refined
hardening process ensure long
service life of the tip, improved
corrosion protection and an exact
fit.
Kraftform Comfort
The Kraftform Comfort series offers a wide and diverse range of screwdrivers for universal
use, with the distinctive Kraftform handle.
58

Kraftform Classic also offers the distinctive Kraftform handle in
a single-component variant.
The ergonomic Kraftform handle
prevents injury to the hand-arm
system.
The Wera Black Point tip and a refined
hardening process ensure long
service life of the tip, improved
corrosion protection and an exact
fit.
The bit material used for
manufacturing is subjected to a
specific Wera hardening process
and this ensures longer product
service life.
Kraftform Classic
Screwdrivers
59

Code mm mm mm mm mm
05031400002 0.4 2.0 60 81 2.5 5
/64
" 2 3
/8
" 10
05031401002 0.4 2.5 75 81 2.5 3
/32
" 3" 10
05031402002 0.5 3.0 80 81 3.0 1
/8
" 3 1
/8
" 10
05031403002 0.5 3.0 150 81 3.0 1
/8
" 6" 10
05031404002 0.5 3.0 200 81 3.0 1
/8
" 8" 5
05031405002 0.6 3.5 100 81 3.5 9
/64
" 4" 10
05031406002 0.6 3.5 125 81 3.5 9
/64
" 5" 10
05031407002 0.6 3.5 200 81 3.5 9
/64
" 8" 5
05031408002 0.8 4.0 100 98 4.0 5
/32
" 4" 10
05031409002 0.8 4.0 150 98 4.0 5
/32
" 6" 10
05031410002 0.8 4.0 200 98 4.0 5
/32
" 8" 5
05031411002 0.8 4.0 300 98 4.0 5
/32
" 12" 2
05345283001 0.8 4.5 100 98 4.5 5
/32
" 4" 10
05031412002 1.0 5.5 125 98 5.5 7
/32
" 5" 10
05031413002 1.0 5.5 150 98 5.5 7
/32
" 6" 10
05031414002 1.0 5.5 200 98 5.5 7
/32
" 8" 5
05031415002 1.0 5.5 300 98 5.5 7
/32
" 12" 2
05031416002 1.2 6.0 100 105 6.0 15
/64
" 4" 10
Code mm mm mm mm
05031420002 0.8 5.0 100 98 3
/16
" 4" 10
05031421002 1.0 6.0 125 105 15
/64
" 5" 10
05031422002 1.2 6.5 150 105 1
/4
" 6" 10
05031423002 1.2 6.5 200 105 1
/4
" 8" 5
05031424002 1.2 7.0 150 105 9
/32
" 6" 10
05031425002 1.2 8.0 175 112 5
/16
" 7" 5
05031426002 1.6 8.0 175 112 5
/16
" 7" 5
05031427002 1.6 10.0 200 112 3
/8
" 8" 5
05031430002 0.6 3.5 4 - 75 81 9
/64
" 3" 10
05031431002 0.8 4.0 4 - 90 81 5
/32
" 3 1
/2
" 10
05031432002 0.8 4.5 5 8 90 98 0.178" 3 1
/2
" 10
05031433002 1.0 5.5 6 10 100 98 7
/32
" 4" 10
05031434002 1.2 6.5 6 10 125 105 1
/4
" 5" 10
05031435002 1.2 7.0 6 10 125 105 9
/32
" 5" 10
05031436002 1.6 9.0 8 13 150 112 11
/32
" 6" 10
05031437002 1.6 10.0 8 13 175 112 3
/8
" 7" 5
Code mm mm mm
05031440002 PH 0 60 81 3.0 2 3
/8
" 5
05031441002 PH 1 80 98 4.5 3 1
/8
" 10
05031442002 PH 1 200 98 4.5 8" 2
05031443002 PH 1 300 98 4.5 12" 2
05031444002 PH 2 100 105 6.0 4" 10
05031445002 PH 2 200 105 6.0 8" 2
05031446002 PH 2 300 105 6.0 12" 2
05031447002 PH 3 150 112 8.0 6" 5
05031448002 PH 4 200 112 10.0 8" 2
Kraftform Comfort
Convenient, safe, good!
Blade: Round
Handle: Kraftform Comfort with non-roll feature, multi-component
Blade: Round
1334 SK Screwdriver for slotted screws
Blade: Hexagonal with bolster from 0.8 x 4.5
Blade: Round
60

Code mm mm mm mm
05031450002 PH 0 4 60 81 2 3
/8
" 5
05031451002 PH 1 5 8 80 98 2 3
/8
" 10
05031452002 PH 2 6 10 100 105 4" 10
05031453002 PH 3 8 13 150 112 4" 5
Code mm mm mm
05031500002 TX 5 60 81 3.5 2 3
/8
" 10
05031501002 TX 6 60 81 3.5 2 3
/8
" 10
05031502002 TX 7 60 81 3.5 2 3
/8
" 10
05031503002 TX 8 60 81 3.5 2 3
/8
" 10
05031504002 TX 9 60 81 4.0 2 3
/8
" 10
05031505002 TX 10 80 81 4.0 3 1
/8
" 10
05031506002 TX 15 80 98 4.0 3 1
/8
" 10
05031507002 TX 20 100 98 4.5 4" 10
05031508002 TX 25 100 105 5.0 4" 10
05031509002 TX 27 115 105 5.5 4 9
/16
" 10
05031510002 TX 30 115 105 6.0 4 9
/16
" 10
05031511002 TX 40 130 112 7.0 5 3
/16
" 10
05031512002 TX 45 130 112 8.0 5 1
/8
" 10
Code mm mm mm
05031520002 TX 7 60 81 3.5 2 3
/8
" 5
05031521002 TX 8 60 81 3.5 2 3
/8
" 5
05031522002 TX 9 60 81 4.0 2 3
/8
" 5
05031523002 TX 10 80 81 4.0 3 1
/8
" 5
05031524002 TX 15 80 98 4.0 3 1
/8
" 5
05031525002 TX 20 100 98 4.5 4" 5
05031526002 TX 25 100 105 5.0 4" 5
05031527002 TX 27 115 105 5.5 4 9
/16
" 5
05031528002 TX 30 115 105 6.0 4 9
/16
" 5
05031529002 TX 40 130 112 7.0 5 1
/8
" 5
1350 SK PH Screwdriver for Phillips screws
1367 TORX®
screws
Application: TORX®
socket screws
Blade: Round
1367 TORX®
BO screwdriver for tamper-proof TORX®
screws
Application: TORX®
socket screws with safety pin
Blade: Round
TORX®
screws. The screws contain a pin
that protrudes into the drive proﬁle so
that "normal" TORX®
tools cannot be
used. This pin ﬁts into the borehole of
TORX®
BO tools allowing safety
screws to be unfastened.
TORX®
with borehole
Screwdrivers
61

Code
05031551002 11334 1 x 1.2x6.5x150
1335 1 x 0.5x3.0x80; 1 x 0.8x4.0x100;
1 x 1.0x5.5x125
1350 PH 1 x PH 1x80; 1 x PH 2x100
Code
05031556002 11334 SK 1 x 0.6x3.5x75; 1 x 0.8x4.0x90;
1 x 1.0x5.5x100; 1 x 1.2x6.5x125
1350 SK PH 1 x PH 1x80; 1 x PH 2x100
Code
05345246001 11334 SK 1 x 1.2x6.5x125; 1 x 1.6x9.0x150
1335 1 x 0.8x4.0x100; 1 x 0.8x4.0x150;
1 x 0.8x4.5x100
1350 PH 1 x PH 1x80; 1 x PH 2x100
Code
05345249001 11334 1 x 1.2x6.5x150
1335 1 x 0.5x3.0x80; 1 x 0.8x4.0x100;
1 x 1.0x5.5x125
1350 PH 1 x PH 1x80; 1 x PH 2x100
1334/6 Screwdriver set Kraftform Comfort
Kraftform Comfort
1334 SK/6 Screwdriver set Kraftform Comfort
1334/1335/1350/7 Screwdriver set Kraftform Comfort
1335/1350/6 Screwdriver set Kraftform Comfort
Hexagon
62

Code
05345248001 11334 1 x 1.2x6.5x150
1335 1 x 0.5x3.0x80; 1 x 0.8x4.0x100
1350 PH 1 x PH 1x80; 1 x PH 2x100
Code
05031554002 11367 TORX®
1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 30x115; 1 x TX 40x130
Code
05345256001 11367 TORX®
1 x TX 6x60; 1 x TX 7x60;
1 x TX 8x60; 1 x TX 9x60; 1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 27x115; 1 x TX 30x115; 1 x TX 40x130
Code
05345255001 11367 TORX®
1 x TX 6x60; 1 x TX 8x60; 1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 27x115; 1 x TX 30x115
1335/1350/5 Screwdriver set Kraftform Comfort
1367/6 TORX®
screwdriver set Kraftform Comfort
Application: TORX®
screws
1367/11 TORX®
Application: TORX®
screws
1367/8 TORX®
Application: TORX®
screws
Screwdrivers
63

Code
05345254001 11367 TORX®
1 x TX 6x60; 1 x TX 7x60; 1 x TX 8x60;
1 x TX 9x60; 1 x TX 10x80; 1 x TX 15x80
Code
05345257001 11367 TORX®
1 x TX 8x60; 1 x TX 10x80; 1 x TX 15x80;
1 x TX 20x100; 1 x TX 25x100
Code
05345258001 11367 TORX®
BO 1 x TX 7x60; 1 x TX 8x60; 1 x TX 9x60;
1 x TX 10x80; 1 x TX 15x80; 1 x TX 20x100;
1 x TX 25x100
1367/6 TORX®
Application: TORX®
screws
Kraftform Comfort
1367/5 TORX®
Application: TORX®
screws
1367/7 TORX®
BO screwdriver set Kraftform Comfort
for tamper-proof TORX®
screws
Application: TORX®
screws with safety pin (BO = with bore hole)
TORX®
drive profiles transfer torque
between tool and screw by line or
surface contact rather than point
contact as many other profiles. This
protects both the screw and the tool
profile. It also increases the amount
of torque and power that can
be transferred.
TORX®
64

Code mm mm mm mm mm
05031209003 0.4 2.5 75 81 2.5 3
/32
" 3" 10
05031210003 0.5 3.0 80 81 3.0 9
/64
" 3 1
/8
" 10
05031211003 0.8 4.0 100 98 4.0 5
/32
" 4" 10
05031212003 1.0 5.5 125 98 5.5 7
/32
" 5" 10
Code mm mm mm mm mm
05031200003 1.2 6.5 150 105 6.0 1
/4
" 6" 10
05031201003 1.2 8.0 175 112 7.0 5
/16
" 7" 5
05031202003 1.6 10.0 200 112 9.0 3
/8
" 8" 5
Code mm mm mm
05031219003 PH 0 60 81 3.0 2 3
/8
" 5
05031220003 PH 1 80 98 4.5 3 1
/8
" 10
05031221003 PH 2 100 105 6.0 4" 10
05031222003 PH 3 150 112 8.0 6" 5
Kraftform Classic
Proven quality over many years!
Blade: Round
Handle: Kraftform Classic with non-roll feature, single-component
Application: For slotted screws
Blade: Round
Blade: Round
Screwdrivers
65

Code
05031280002 11734 1 x 1.2x6.5x150
1735 1 x 0.5x3.0x80; 1 x 0.8x4.0x100;
1 x 1.0x5.5x125
1750 PH 1 x PH 1x80; 1 x PH 2x100
Code mm mm mm
05031300002 TX 8 60 81 3.5 2 3
/8
" 10
05031301002 TX 9 60 81 4.0 2 3
/8
" 10
05031302002 TX 10 80 81 4.0 3 1
/8
" 10
05031303002 TX 15 80 98 4.0 3 1
/8
" 10
05031304002 TX 20 100 98 4.5 4" 10
05031305002 TX 25 100 105 5.0 4" 10
05031308002 TX 27 115 105 5.5 4 9
/16
" 10
05031306002 TX 30 115 105 6.0 4 9
/16
" 10
05031307002 TX 40 130 112 7.0 5 1
/8
" 10
1734/6 Screwdriver set Kraftform Classic
Kraftform Classic
Proven quality over many years!
1767 Screwdriver for TORX®
screws
Application: TORX®
socket screws
Blade: Round
Non-roll feature
The Wera Black Point tip and
a reﬁned hardening process
ensure long service life of the tip,
improved corrosion protection and
an exact ﬁt.
Black Point Tip
66

Code
05345240001 11767 TORX®
1 x TX 6x50; 1 x TX 8x60; 1 x TX 10x80;
1 x TX 15x80; 1 x TX 20x100; 1 x TX 25x100;
1 x TX 27x115; 1 x TX 30x115
1767/8 TORX®
screwdriver set Kraftform Classic
Application: TORX®
screws
TORX®
drive profiles transfer torque
between tool and screw by line or
surface contact rather than point
contact as many other profiles. This
protects both the screw and the tool
profile. It also increases the amount
of torque and power that can
be transferred.
TORX®
Screwdrivers
67

Flagdriver and Stubby Series
1267 A TORX®
flagdriver for TORX®
screws
Application: TORX®
socket screws
Blade: Round
Design: BlackLaser surface
Handle: Multi-component
1267 A TORX PLUS®
flagdriver for TORX PLUS®
screws
socket screws
Blade: Round
Design: BlackLaser surface
1267 B TORX®
combination flagdriver for TORX®
and
hexagon socket screws
Application: TORX®
and hexagon socket screws
Blade: Hexagon
Design: TORX®
and hexagon, BlackLaser surface
1267 B TORX PLUS®
combination flagdriver for TORX PLUS®
Blade: Hexagon
Design: TORX PLUS®
and hexagon, BlackLaser surface
Code mm mm mm
05026350003 TX 6 33 62.0 3.0 1 19
/64
" 10
05026351003 TX 7 33 62.0 3.0 1 19
/64
" 10
05026352002 TX 8 40 69.0 3.0 1 37
/64
" 10
05026353003 TX 9 40 69.0 3.0 1 37
/64
" 10
05026354002 TX 10 40 69.0 3.0 1 37
/64
" 10
Code mm mm mm
05026360002 6 IP 33 62.0 3.0 1 19
/64
" 10
05026361003 7 IP 33 62.0 3.0 1 19
/64
" 10
05026362002 8 IP 40 69.0 3.0 1 37
/64
" 10
05026363003 9 IP 40 69.0 3.0 1 37
/64
" 10
05026364002 10 IP 40 69.0 3.0 1 37
/64
" 10
Code mm mm mm
05026370002 TX 9 3.5 42 81.0 1 5
/8
" 10
05026371002 TX 10 3.5 42 81.0 1 5
/8
" 10
05026372003 TX 15 3.5 47 86.0 1 27
/32
" 10
05026373004 TX 15 4 47 86.0 1 27
/32
" 10
05026374002 TX 20 4 47 86.0 1 27
/32
" 10
Code mm mm mm
05026380003 9 IP 3.5 42 81.0 1 5
/8
" 10
05026381002 10 IP 3.5 42 81.0 1 5
/8
" 10
05026382003 15 IP 3.5 47 86.0 1 27
/32
" 10
05026383003 15 IP 4 47 86.0 1 27
/32
" 10
05026384002 20 IP 4 47 86.0 1 27
/32
" 10
68

336 Stubby/Carburettor screwdriver
Blade: Round
Handle: Kraftform with non-roll feature, Weralit II, single-component
Stubby/Carburettor screwdriver
Blade: Round
Handle: Kraftform, with non-roll feature, Weralit II, single-component
Code mm mm mm mm mm
05110068002 0.6 3.5 25 54 3.5 9
/64
" 1" 5
05110069003 0.8 4.0 25 54 4.0 5
/32
" 1" 5
05110070003 1.0 5.5 25 54 5.5 7
/32
" 1" 5
05110075003 1.2 6.5 25 54 6.5 1
/4
" 1" 5
05110078002 1.2 8.0 25 54 8.0 5
/16
" 1" 5
Code mm mm mm
05008775003 PH 01 25 54 4.5 1" 5
05008780005 PH 02 25 54 6.0 1" 5
05008782002 PH 03 25 54 6.0 1" 5
69
Screwdrivers

Accessories
Indispensable aids for screwdriving jobs
335 MS Slotted screwdriver
Application: Suitable for less demanding screwdriving jobs and for general
uses such as e.g. depth of proﬁle measurements, checking for
signs of rusting, removal of dirt
Blade: Round
Design: Stainless steel for high corrosion protection
Handle: Kraftform with non-roll feature, single-component, cellulose
acetate, equipped with practical clip for attaching e. g. to the
breast pocket
Wera Star - Magnetiser / Demagnetiser
1427 Awl
Handle: Weralit II, single-component
Blade: Extends through handle
?
Code mm mm mm mm mm
05008004002 0.5 3.0 50 70 3.0 1
/8
" 2" 5
Code mm
05073403002 48.0 1
Code mm mm
05027405004 105 92 4 3
/16
" 5
70
The Wera magnetiser/demagnetiser: simply run the tool down the
positive side of the Wera magnetiser/demagnetiser and the tool
immediately becomes magnetised and is able to hold the screw
securely on the blade. To demagnetise the tool, simply run it down
one of the four negative sides.
How to hold any screw securely on
the screwdriver

Rack for Kraftform screwdrivers
Rack for Kraftform Micro screwdrivers
Code mm mm
05134001002 190.0 50,0 1
Code mm mm
05134002002 190.0 80 1
Screwdrivers
71

1441 Screw gripper attachment for screwdriver blades,
long bits and L-keys with holding function for screws
proﬁles and sizes securely on the tool, suitable for round and
hexagon blades with a diameter from 4.5 mm to 6.0 mm
Design: Elastomer
1440/1442 Screw gripper set
hexagon blades with a diameter from 4.5 mm to 6.0 mm and
6.5 mm to 8.0 mm
Construction: Elastomer
Code mm mm
05073681002 4.5-6.0 41.0 1
Code
05073680002 51440 1 x 4.5 - 6.0x41.0
1442 1 x 6.5 - 8.0x41.0
For screw gripper sets see page
44, 45, 101, 351, 353, 355, 360
72
Push the screw gripper onto the tip
of the screwdriver until the end of the
blade protrudes from the rubber blade
holder.
Attach the screw to the tip of the
blade and secure it in the screw
gripper.
Pull the screw gripper towards the
screwdriver handle until the two
arms of the gripper sit against the
head of the screw and are spread
slightly apart. The Wera screw gripper
releases the screw automatically after
it has been fastened.
The two gripper arms spread further
apart as they are pushed against the
surface and automatically snap
back when the head of the screw is
countersunk.
When fastening screws in blind holes
the screw gripper is pushed back,
making it possible to reach even
deep-seated screws.
And this is how the gripper works:
Accessories
Indispensable aids for screwdrivers.

Screwdrivers
73
Kraftform Micro Series

74
The highly precise Wera manufacturing quality is indispensable whenever minimum
dimensions are concerned. The three-zone concept reduces fastening time and distinctly
lowers the cost for each screw connection.
Ever lost patience with precision screw
connections?
Kraftform Micro is the ideal screwdriving partner for electronics or
precision engineering applications.

75
The spinning cap and the fast-turning
zone just below the head allow
rapid twisting. This makes
time-consuming grip adjustments,
as required with other conventional
precision screwdrivers, unnecessary.
The power zone has integrated soft
zones near the blade tip to ensure
high torque transfer for loosening
or tightening screws without losing
contact with the screw.
The precision zone directly above the
blade gives the user a better feel for
the right rotation angle during
fine adjustment work.
The Wera Black Point tip, as well as
a refined hardening process, ensure
long service life and enhanced
corrosion protection.
Multi-component screwdriver handle
for ergonomic working.
Indispensable for many users,
including electronics technicians,
opticians, precision engineers,
jewellers, EDP hardware fitters and
model-makers.
Screwdrivers

???????????????????
Code mm mm mm mm mm
05117990002 0.16 0.8 40 97 2.0 1
/32
" 1 9
/16
" 10
05117991002 0.18 1.0 40 97 2.0 0.04" 1 9
/16
" 10
05117992002 0.20 1.2 40 97 2.0 0.05" 1 9
/16
" 10
05118002003 0.23 1.5 40 97 2.0 1
/16
" 1 9
/16
" 10
05118003002 0.23 1.5 60 97 2.0 1
/16
" 2 3
/8
" 10
05118000002 0.25 1.2 40 97 2.0 0.05" 1 9
/16
" 10
05118001002 0.25 1.2 60 97 2.0 0.05" 2 3
/8
" 10
05117993002 0.30 1.8 40 97 2.0 0.07" 1 9
/16
" 10
05118004002 0.30 1.8 60 97 2.0 0.07" 2 3
/8
" 10
05118017002 0.30 2.0 50 97 2.0 0.07" 2" 10
05118005002 0.40 2.0 40 97 2.5 5
/64
" 1 9
/16
" 10
05345287001 0.40 2.0 50 97 2.5 5
/64
" 2" 10
05118006004 0.40 2.0 60 97 2.5 5
/64
" 2 3
/8
" 10
05118007002 0.40 2.0 100 97 2.5 5
/64
" 4" 10
05117994002 0.40 2.5 50 97 2.5 3
/32
" 2" 10
05118008004 0.40 2.5 80 97 2.5 3
/32
" 3 1
/8
" 10
05118009002 0.40 2.5 100 97 2.5 3
/32
" 4" 10
05117995002 0.50 3.0 50 97 3.0 1
/8
" 2" 10
05118010003 0.50 3.0 80 97 3.0 1
/8
" 3 1
/8
" 10
05118011002 0.50 3.0 100 97 3.0 1
/8
" 4" 10
05117996002 0.50 3.0 150 97 4.0 1
/8
" 6" 10
05118012004 0.60 3.5 80 97 4.0 9
/64
" 3 1
/8
" 10
05118014004 0.80 4.0 80 97 4.0 5
/32
" 3 1
/8
" 10
05118015002 0.80 4.0 100 97 4.0 5
/32
" 4" 10
05118016002 0.80 4.0 150 97 4.0 5
/32
" 6" 10
Code mm mm mm
05118019002 PH 00 40 97 2.5 1 9
/16
" 10
05118020004 PH 00 60 97 3.0 2 3
/8
" 10
05118022004 PH 0 60 97 3.0 2 3
/8
" 10
05118023002 PH 1 60 97 4.0 2 3
/8
" 10
05118024004 PH 1 80 97 4.0 3 1
/8
" 10
05118025002 PH 1 100 97 4.0 4" 10
Code mm mm mm
05118030003 PZ 0 60 97 3.0 2 3
/8
" 10
05118032003 PZ 1 80 97 4.0 3 1
/16
" 10
76
The electronic TORX®
HF screwdriver
with holding function literally presses
the screw onto the screwdriver.
The conical driving ﬂanks that taper
toward the tip of the tool, the optimised
ﬂank base and the ideal engage depth
hold the screw securely on the blade.
How can I hold my TORX®
screw
securely on the screwdriver?
Series Kraftform Micro
The superior screwdriver for electronics technicians
2035 Screwdriver for slotted screws for electronic
applications
Blade: Round
Handle: Kraftform Micro with non-roll feature and rotating cap, multi-
component
2050 PH Screwdriver for Phillips screws for electronic
applications
Blade: Round
component
2055 PZ Screwdriver for Pozidriv screws for electronic
applications
screws
Blade: Round
component
*)

???????????????????
Code mm mm mm
05118180002 TX 4 40 97 2.5 1 9
/16
" 5
05118181002 TX 5 40 97 3.0 1 9
/16
" 5
05118182002 TX 6 40 97 3.0 1 9
/16
" 5
05118183002 TX 7 60 97 3.0 2 3
/8
" 5
05118184002 TX 8 60 97 3.0 2 3
/8
" 5
05118185002 TX 9 60 97 4.0 2 3
/8
" 5
05118186002 TX 10 60 97 4.0 2 3
/8
" 5
05118187002 TX 15 60 97 4.0 2 3
/8
" 5
05118188002 TX 20 60 97 4.0 2 3
/8
" 5
Code mm mm mm
05118035002 TX 1 40 97 2.0 1 9
/16
" 5
05118036002 TX 2 40 97 2.0 1 9
/16
" 5
05118037002 TX 3 40 97 2.0 1 9
/16
" 5
05118039002 TX 4 40 97 2.5 1 9
/16
" 5
05118040003 TX 5 40 97 3.0 1 9
/16
" 5
05118042003 TX 6 40 97 3.0 1 9
/16
" 5
Code mm mm mm
05118044003 TX 7 60 97 3.0 1 9
/16
" 5
05118046003 TX 8 60 97 3.0 2 3
/8
" 5
05118048003 TX 9 60 97 4.0 2 3
/8
" 5
05118050003 TX 10 60 97 4.0 2 3
/8
" 5
05118052003 TX 15 60 97 4.0 2 3
/8
" 5
05118054003 TX 20 60 97 4.0 2 3
/8
" 5
77
The Kraftform Micro, with its three
zones and their specific arrangement,
satisfies these requirements perfectly.
The free-turning cap that provides
support for the hand works with these
advantages, enabling quick and easy
precision work.
How to perform precision
screwdriving jobs quickly whilst still
applying the required degree of force
2067 TORX®
HF Screwdriver for TORX®
screws for
electronic applications with holding function
Application: TORX®
socket screws
Blade: Round
Global Technologies Inc. specifications, chrome-plated, Black
Point
component
2067 TORX®
Screwdriver for TORX®
screws for
electronic applications
Application: TORX®
socket screws
Blade: Round
component
2067 TORX®
BO Screwdriver for tamper-proof TORX®
screws for electronic applications
Application: TORX®
socket screws with safety pin
Blade: Round
Design: Bore hole in TORX®
section, chrome-plated, Black Point
component
Screwdrivers

?
Code mm mm mm mm
05118060003 0.7 40 97 3.0 1 9
/16
" 5
05118062003 0.9 40 97 3.0 1 9
/16
" 5
05118064003 1.3 40 97 3.0 1 9
/16
" 5
05118066002 1.5 60 97 3.0 2 3
/8
" 5
05118068003 2.0 60 97 3.0 2 3
/8
" 5
05118070003 2.5 60 97 4.0 2 3
/8
" 5
05118072003 3.0 60 97 4.0 2 3
/8
" 5
05345284001 0,028" 40 97 3.0 1 9
/16
" 5
05345285001 0,035" 40 97 3.0 1 9
/16
" 5
05118074002 0.05" 40 97 3.0 1 9
/16
" 5
05118076002 1
/16
" 60 97 3.0 2 3
/8
" 5
05118078002 5
/64
" 60 97 3.0 2 3
/8
" 5
05118080002 3
/32
" 60 97 4.0 2 3
/8
" 5
05118082002 7
/64
" 60 97 4.0 2 3
/8
" 5
05118075002 1
/8
" 60 97 4.0 2 3
/8
" 5
Code mm mm mm mm
05118089002 1.3 60 97 3.0 2 3
/8
" 5
05118090002 1.5 60 97 3.0 2 3
/8
" 5
05118092002 2.0 60 97 3.0 2 3
/8
" 5
05118094002 2.5 60 97 4.0 2 3
/8
" 5
05118096002 3.0 60 97 4.0 2 3
/8
" 5
05118098002 1
/16
" 60 97 3.0 2 3
/8
" 5
05118100002 5
/64
" 60 97 3.0 2 3
/8
" 5
05118102002 3
/32
" 60 97 3.0 2 3
/8
" 5
05118106002 7
/64
" 60 97 4.0 2 3
/8
" 5
05118103002 1
/8
" 60 97 4.0 2 3
/8
" 5
Code mm mm mm
05118200002 IP 4 40 97 2.5 1 9
/16
" 5
05118201002 IP 5 40 97 3.0 1 9
/16
" 5
05118202002 IP 6 40 97 3.0 1 9
/16
" 5
05118203002 IP 7 60 97 3.0 2 3
/8
" 5
05118204002 IP 8 60 97 3.0 2 3
/8
" 5
05118205002 IP 9 60 97 4.0 2 3
/8
" 5
05118206002 IP 10 60 97 4.0 2 3
/8
" 5
05118207002 IP 15 60 97 4.0 2 3
/8
" 5
05118208002 IP 20 60 97 4.0 2 3
/8
" 5
78
The Wera magnetiser/demagnetiser: simply run the tool down the
positive side of the Wera magnetiser/demagnetiser and the tool
immediately becomes magnetised and is able to hold the screw
securely on the blade. To demagnetise the tool, simply run it down
one of the four negative sides. See page 70.
How to hold any screw securely on
the screwdriver
2054 Screwdriver for hexagon socket screws for
Blade: Round
Design: Hex-Plus, chrome-plated, Black Point
component
2052 Ball end screwdriver for hexagon socket screws
for electronic applications
Blade: Round
Design: Hexagon ball end, chrome-plated, Black Point
component
2067 TORX PLUS®
screwdriver for TORX PLUS®
screws
for electronic applications
socket screws
Blade: Round
component

?
Code mm mm mm mm
05118108002 1.5 60 97 4.0 2 3
/8
" 5
05118109002 1.8 60 97 4.0 2 3
/8
" 5
05118110002 2.0 60 97 4.0 2 3
/8
" 5
05118112002 2.5 60 97 4.0 2 3
/8
" 5
05118114002 3.0 60 97 5.0 2 3
/8
" 5
05118116002 3.2 60 97 5.0 2 3
/8
" 5
05118118002 3.5 60 97 5.3 2 3
/8
" 5
05118120002 4.0 60 97 5.5 2 3
/8
" 5
05118122002 4.5 60 97 6.2 2 3
/8
" 5
05118124002 5.0 60 97 7.0 2 3
/8
" 5
05118126002 5.5 60 97 7.8 2 3
/8
" 5
05345281001 6.0 60 97 8.5 2 3
/8
" 5
05118128002 3
/32
" 60 97 5.7 2 3
/8
" 5
05118130002 7
/64
" 60 97 5.7 2 3
/8
" 5
05118132002 1
/8
" 60 97 5.7 2 3
/8
" 5
05118134002 9
/64
" 60 97 5.7 2 3
/8
" 5
05118136002 5
/32
" 60 97 5.7 2 3
/8
" 5
05118135002 3
/16
" 60 97 - 2 3
/8
" 5
05118137002 7
/32
" 60 97 - 2 3
/8
" 5
05345282001 1
/4
" 60 97 8.5 2 3
/8
" 5
Code
05118150003 12035 Micro 1 x 0.30x1.8x60; 1 x 0.40x2.0x60;
1 x 0.40x2.5x80; 1 x 0.50x3.0x80
2050 PH Micro 1 x PH 00x60; 1 x PH 0x60
Code
05118152003 12035 Micro 1 x 0.40x2.5x80; 1 x 0.50x3.0x80;
1 x 0.60x3.5x80; 1 x 0.80x4.0x80
2050 PH Micro 1 x PH 0x60; 1 x PH 1x80
79
Every challenging screwdriving job
merits a perfect problem solution.
Therefore, the extent and depth of
the range is aligned to the needs of
professional users.
Why is the Micro range so
extensive?
2069 Nutdriver for electronic applications
Blade: Round
Design: Chrome-plated
component
2035/6 A Screwdriver set and rack for electronic
applications
2035/6 B Screwdriver set and rack for electronic
applications
Screwdrivers

Code
05345270001 12035 Micro 1 x 0.23x1.5x40; 1 x 0.40x2.0x40;
1 x 0.40x2.5x50; 1 x 0.50x3.0x50;
1 x 0.60x3.5x80; 1 x 0.80x4.0x80
Code
05345272001 12035 Micro 1 x 0.40x2.5x50; 1 x 0.40x2.5x100;
1 x 0.50x3.0x100; 1 x 0.50x3.0x150;
1 x 0.80x4.0x100; 1 x 0.80x4.0x150
2050 PH Micro 1 x PH 0x60
Code
05345271001 12035 Micro 1 x 0.23x1.5x40; 1 x 0.30x2.0x50;
1 x 0.40x2.5x50; 1 x 0.50x3.0x50
2050 PH Micro 1 x PH 00x60; 1 x PH 0x60; 1 x PH 1x60
80
2035/6 Screwdriver set for electronic applications
2035/2050 PH 0/7 Screwdriver set for electronic
applications
2035/2050 PH 00 - 01/7 Screwdriver set for electronic
applications

Code
05345276001 12067 TORX®
HF 1 x TX 5x40; 1 x TX 6x40; 1 x TX 7x60;
1 x TX 8x60; 1 x TX 9x60; 1 x TX 10x60;
1 x TX 15x60
Code
05345277001 12067 TORX®
HF 1 x TX 6x40; 1 x TX 7x60; 1 x TX 8x60;
1 x TX 9x60; 1 x TX 10x60; 1 x TX 15x60
???????????????????
81
2067/7 HF TORX®
screwdriver set with holding
function for electronic applications
Application: TORX®
socket screws
2067/6 TORX®
HF TORX®
screwdriver set with holding
function for electronic applications
Application: TORX®
socket screws
The electronic TORX®
HF screwdriver
with holding function literally presses
the screw onto the screwdriver.
The conical driving ﬂanks that taper
toward the tip of the tool, the optimised
ﬂank base and the ideal engage depth
hold the screw securely on the blade.
How can I hold my TORX®
screw
securely on the screwdriver?
Screwdrivers

Code
05345274001 12054 Micro 1 x 0,028"x40; 1 x 0,035"x40; 1 x 0.05"x40;
1 x 1/16"x60; 1 x 5/64"x60; 1 x 3/32"x60;
1 x 7/64"x60; 1 x 1/8"x60
Code
05345273001 12054 Micro 1 x 0.7x40; 1 x 0.9x40; 1 x 1.3x40;
1 x 1.5x60; 1 x 2.0x60; 1 x 2.5x60;
1 x 3.0x60
Code
05118154003 12067 TORX®
BO
Micro
1 x TX 7x60; 1 x TX 8x60; 1 x TX 9x60;
1 x TX 10x60; 1 x TX 15x60; 1 x TX 20x60
?
82
2054/8 Hexagon screwdriver set for electronic
applications
applications
2067/6 TORX®
BO screwdriver set and rack for
Application: TORX®
socket screws with safety pin (BO = with bore hole)
TORX®
screws. The screws contain a pin that
protrudes into the drive proﬁle so that
"normal" TORX®
tools cannot be used.
This pin ﬁts into the borehole of TORX®
BO tools allowing safety screws to be
unfastened.
TORX®
with borehole

Code
05118156003 12052 Micro 1 x 1.5x60; 1 x 2.0x60; 1 x 2.5x60;
1 x 3.0x60
2054 Micro 1 x 0.9x40; 1 x 1.3x40
Code
05345275001 12052 Micro 1 x 1.3x60; 1 x 1.5x60; 1 x 2.0x60;
1 x 2.5x60; 1 x 3.0x60
83
2052/6 Hexagon screwdriver set and rack for
Application: Ball end for hexagon socket screws
applications
Application: Ball end for hexagon socket screws
The multi-component Kraftform Micro
screwdriver handle is perfect for
ergonomic working.
The three-zone concept reduces
fastening time and distinctly
lowers the cost for each screw
connection.
Multi-component handle
The Wera Black Point tip, as
well as a reﬁned hardening
process, ensure long service
life and enhanced corrosion
protection.
Black Point Tip
Screwdrivers

Code
05345278001 12069 Micro 1 x 2.5x60; 1 x 3.0x60; 1 x 3.5x60;
1 x 4.0x60; 1 x 4.5x60; 1 x 5.0x60;
1 x 5.5x60; 1 x 6.0x60
Code
05345279001 12069 Micro 1 x 3/32"x60; 1 x 7/64"x60; 1 x 1/8"x60;
1 x 9/64"x60; 1 x 5/32"x60; 1 x 3/16"x60;
1 x 7/32"x60; 1 x 1/4"x60
Code
05118158003 12069 Micro 1 x 2.0x60; 1 x 2.5x60; 1 x 3.0x60;
1 x 3.5x60; 1 x 4.0x60; 1 x 5.0x60
84
2069/8 2,5mm - 6,0mm Nutdriver set for electronic
applications
2069/8 3
/32" - ¼" Nutdriver set for electronic
applications
2069/6 Screwdriver set and rack for electronic
applications

85
Series 400 T-Handle Screwdrivers

86
The ergonomic design of the
T-handle fills the palm of the hand.
The fingers rest in the soft, rounded
recess, and the whole hand is in
contact with the handle - so there is
no friction loss between the hand and
handle.
The ergonomic design of the handle
enables high torque to be applied
for loosening or tightening jobs.
The blades are made out of special
alloy steels for superior wear
resistance and robustness.
Hex-Plus provides more contact surface
inside the screw head.This reduces
the notching effect to a minimum, and
more or less eliminates the risk of
rounding out the screw head.
The T-handle series is needed whenever particularly high torque for loosening or
tightening jobs needs to be applied. Especially high force can be transferred by using the
blade as an extension of the lower arm. The power is transferred positively, i.e.
there is no frictional loss between the hand and the handle.
Ever needed more leverage?

Code mm mm mm
05013300002 2 100 27 61 4" 5
05013301002 2 200 27 61 8" 5
05013302004 2.5 100 27 61 4" 5
05013303002 2.5 200 27 61 8" 5
05013304002 3 100 33 70 4" 5
05013305002 3 150 33 70 6" 5
05013330002 3 200 33 70 8" 5
05013331002 3 350 33 70 14" 5
05013332003 4 100 33 70 4" 5
05013306002 4 150 33 70 6" 5
05013307002 4 200 33 70 8" 5
05013333002 4 350 33 70 14" 5
05013334002 5 100 44 87 4" 5
05013308002 5 150 44 87 6" 5
05013309002 5 200 44 87 8" 5
05013335002 5 350 44 87 18" 5
05013336002 5 450 44 87 14" 5
05013337002 6 100 44 87 4" 5
05013338002 6 150 44 87 6" 5
05013310002 6 200 44 87 8" 5
05013339002 6 350 44 87 14" 5
05013311002 7 200 44 87 8" 5
05013340002 8 100 44 87 4" 5
05013341002 8 150 44 87 6" 5
05013312002 8 200 44 87 8" 5
05013313002 8 350 44 87 14" 5
05013342002 10 100 44 87 4" 5
05013314002 10 200 44 87 8" 5
87
Hex-Plus tools for hexagon socket screws provide more contact
surface inside the screw proﬁle. This reduces the notching effect
to a minimum and protects the head of the screw.
Series 400 T-Handle
Ideal for high torque
454 T-handle hexdriver
Blade: Hexagon
Design: Hex-Plus, chamfered, chrome-plated
Handle: T-handle, Weralit II, single-component
Screwdrivers

Code mm mm mm
05344536002 3
/32
" 100 27 61 4" 5
05344537002 7
/64
" 100 27 61 4" 5
05344538002 1
/8
" 100 33 70 4" 5
05344546002 9
/64
" 150 33 70 6" 5
05344545002 5
/32
" 150 33 70 6" 5
05344544002 3
/16
" 150 44 87 6" 5
05344543002 7
/32
" 150 44 87 6" 5
05344542002 1
/4
" 200 44 87 8" 5
05344541002 5
/16
" 200 44 87 8" 5
05344540002 3
/8
" 200 44 87 8" 5
Code mm mm mm mm
05013350002 TX 6 100 27 61 4" 3.0 5
05013352002 TX 7 100 27 61 4" 3.0 5
05013354002 TX 8 100 27 61 4" 3.5 5
05013356002 TX 9 100 27 61 4" 3.5 5
05013358002 TX 10 100 27 61 4" 4.0 5
05013360002 TX 15 100 33 70 4" 4.0 5
05013362002 TX 20 100 33 70 4" 4.5 5
05013364003 TX 20 200 33 70 8" 4.5 5
05013366002 TX 25 100 33 70 4" 5.0 5
05013368003 TX 25 200 33 70 8" 5.0 5
05013370003 TX 27 200 44 87 8" 6.0 5
05013372003 TX 30 200 44 87 8" 6.0 5
05013374003 TX 40 200 44 87 8" 8.0 5
05013376003 TX 45 200 44 87 8" 9.0 5
Code mm mm mm
05013250002 1
/4
" 115 44 87 4 9
/16
" 5
05013252004 1
/4
" 230 44 87 9" 5
88
Series 400 T-Handle
Perfect for high torque
454 T-handle hexdriver, imperial
Blade: Hexagon
Design: Hex-Plus, chamfered, chrome-plated
467 T-handle TORX®
driver
Application: TORX®
screws
Blade: Round
410 T-handle ¼" square drive socket adaptor
Application: 1
/4
" drive sockets
Blade: Round
Design: 1
/4
" square drive, chrome-plated

Code mm mm mm
05013390002 1
/4
" 45 44 87 1 25
/32
" 2
Code
05345235001 1467 TORX®
1 x TX 9x100; 1 x TX 10x100; 1 x TX 15x100;
1 x TX 20x100; 1 x TX 25x100; 1 x TX 27x200;
1 x TX 30x200
89
Rapid-in and self-lock
The bit can be pushed into the
adaptor without moving the sleeve.
The lock is activated automatically
as soon as the bit is applied to the
screw. Bits are held securely and
wobble-free.
Rapid-out
Simply push the sleeve forward to
change the bit. The spring
mechanism lifts the bit oﬀ the
magnet and unlocks the tool.
The bit can be easily removed. The
rapid-out function makes it easy to
remove even the smallest bits
without extra tools.
Chuck-all
The Rapidaptor quick-release chucks
hold ¼" DIN 3126-C 6.3 and E 6.3 as
well as Wera series 1 and 4 bits.
Single-hand function
Every function of the Rapidator
quick-release chuck, such as
inserting or releasing bits, can be
carried out with one hand.
This is faster, more economical and
more ergonomic. There are no
unnecessary manoeuvres.
Rapidaptor489 R T-handle Rapidaptor
Application: Suitable for 1
/4
" DIN 3126-C 6.3 and E 6.3 (ISO 1173) hexagon
insert bits und Wera Series 1 and 4
Drive: 1
/4
" hexagon with Rapidaptor rapid-in, rapid-out, rapid-spin,
chuck-all and single-hand technology, magnetic
Handle: T-handle, multi-component
467/7 Screwdriver set T-handle TORX®
driver
Application: TORX®
screws
Screwdrivers

91
VDE Insulated Safety Tools
Kraftform Plus Series 100 94
Kraftform Kompakt VDE 102
Kraftform Comfort VDE 108
Kraftform Classic VDE 112
VDE Tools

92
The individual testing in a
water bath at 10,000 volts, in
accordance with DIN EN 60900 (IEC
60900:2004), ensures safe working
with loads up to 1,000 volts.
Impact strength tested at - 40°C,
guaranteeing safety even under
extreme conditions.
Kraftform handle ensures that it fits
perfectly into the hand, preventing
hand injuries such as blisters and
calluses.
repositioning, without any danger of
the skin "sticking" to the handle. The
softer "anti-slip" zones enable the
low-loss transfer of high forces
– resulting in less screwdriving
effort being required.
Ever had an electric shock?
Kraftform Plus screwdrivers enable a higher transfer of force with less effort, and relieve
the entire hand-arm system – even with intensive use. In addition, the safety issue, always
a top priority at Wera, is very much in focus for series 100 VDE screwdrivers. The quality of
the blades exceeds current standards with regard to hardness and torque strength. Every
tool is tested individually for dielectric strength under a load of 10,000 volts, so as to
ensure safe working with loads up to 1,000 volts.
Wera VDE tools provide more safety than required by current
regulation.

93
identiﬁcation markings on the handle
screwdriver in the tool case or at the
workplace.
Laser treatment burns a micro-rough
surface into the tip of the blade with
an edge hardness of up to 1,000
Vickers. The drive end literally "bites"
into the head of the screw. The
advantages: safer working and
less slipping.
The screwdriver sets are supplied
with a rack that can be attached to
the wall. This ensures organised
storage and quick & easy access.
The rack is also available as an
individual item.
VDE Tools

Code mm mm mm mm
05006100006 1)
0.4 2.5 80 81 3
/32
" 3 1
/8
" 10
05006105005 1)
0.5 3.0 100 81 1
/8
" 4" 10
05006110005 0.6 3.5 100 81 9
/64
" 4" 10
05006115006 0.8 4.0 100 98 5
/32
" 4" 10
05006116002 0.8 4.0 150 98 5
/32
" 6" 5
05006120006 1.0 5.5 125 98 7
/32
" 5" 10
05006121002 1.0 5.5 200 98 7
/32
" 8" 5
05006125007 1.2 6.5 150 105 1
/4
" 6" 10
05006126002 1.2 6.5 200 105 1
/4
" 8" 5
05006130006 1.2 8.0 175 112 5
/16
" 7" 5
05006135002 1.6 8.0 200 112 5
/16
" 8" 5
05006140003 1.6 10.0 200 112 3
/8
" 8" 5
Code mm mm mm mm
05006440002 0.6 3.5 100 81 9
/64
" 4" 10
05006441002 0.8 4.0 100 98 5
/32
" 4" 10
05006442002 1.0 5.5 125 98 7
/32
" 5" 10
Code mm mm
05006150006 1)
PH 0 80 81 3 1
/8
" 5
05006152006 PH 1 80 98 3 1
/8
" 5
05006153002 PH 1 150 98 6" 5
05006154007 PH 2 100 105 4" 5
05006159002 PH 2 200 105 8" 5
05006156005 PH 3 150 112 6" 5
05006158005 1)
PH 4 200 112 8" 2
Code mm mm
05006450002 PH 1 80 98 3 1
/8
" 5
05006451002 PH 2 100 105 4" 5
94
Reduced blade diameter with
integrated protective insulation, allows
sunken screws and spring elements to
be accessed and actuated, individually
tested as per IEC 60900 : 2004.
VDE Insulated screwdriver for slotted
screws with reduced blade diameter
Kraftform Plus – Series 100 VDE
The safety screwdriver when working with live wiring
160 i VDE Insulated screwdriver for slotted screws
Blade: Insulated, individually tested as per IEC 60900 : 2004
Design: Conical tip, Lasertip
1)
without Lasertip
160 iS VDE Insulated screwdriver with reduced blade
diameter for slotted screws
Application: Slotted screws and actuating tool for spring terminals
Blade: Reduced blade diameter with integrated protective insulation,
allows sunken screws and spring elements to be accessed and
actuated, individually tested as per IEC 60900 : 2004
Design: Conical blade, zinc-phosphated
162 i PH VDE Insulated screwdriver for Phillips screws
Design: Lasertip
1)
without Lasertip
162 iS PH VDE Insulated screwdriver with reduced
blade diameter for Phillips screws
allows sunken PH screws to be accessed and actuated,
individually tested as per IEC 60900 : 2004
Design: Blade zinc-phosphated

?
?
Code mm mm
05006460002 PZ 1 80 98 3 1
/8
" 5
05006461002 PZ 2 100 105 4" 5
Code mm mm
05006160005 1)
PZ 0 80 81 3 1
/8
" 5
05006162007 PZ 1 80 98 3 1
/8
" 5
05006163002 PZ 1 150 98 6" 5
05006164008 PZ 2 100 105 4" 5
05006165002 PZ 2 200 105 8" 5
05006166007 PZ 3 150 112 6" 5
05006168004 1)
PZ 4 200 112 8" 2
95
A dielectric strength test under a
10,000 volt load in a water bath is the
only way of reassuring users that their
screwdrivers have been exhaustively
tested for their most important feature:
their insulation. Each individual Wera
VDE screwdriver is subjected to this
test to guarantee safe working up to 1,000 volts.
How do you know a VDE
screwdriver is safe?
It happens time and time again that the
tip slips out of the screw head when
screwdriving, potentially damaging
surfaces, and occasionally even making
contact with live components. The tips
of the Wera Lasertip screwdrivers are
microscopically roughened by means of
a laser. This rough surface literally "bites" itself ﬁrmly into the screw
head – preventing slips. This allows the user to feel secure in their
safety, particularly when working on live wires.
How to prevent the screwdriver from
slipping out of the screw head
165 iS PZ VDE Insulated screwdriver with reduced
blade diameter for Pozidriv screws
screws
allows sunken PZ screws to be accessed and actuated,
Design: Blade zinc-phosphated
*)
165 i PZ VDE Insulated screwdriver for Pozidriv screws
screws
Design: Lasertip
1)
without Lasertip
*)
VDE Tools

Code mm mm
05006455002 # 1 80 98 3 1
/8
" 5
05006456002 # 2 100 105 4" 5
Code mm mm
05006190002 # 1 80 98 3 1
/8
" 5
05006191002 # 2 100 105 4" 5
Code mm mm
05006380002 # 1 80 98 3 1
/8
" 5
05006381002 # 2 100 105 4" 5
96
For the use in terminal blocks, control
cabinets, switches, relays, sockets etc.
PlusMinus screwdrivers
162 iS PH/S VDE Insulated screwdriver for PlusMinus
screws (Phillips/slotted) with reduced blade diameter
Application: PlusMinus screws (Phillips/slotted)
allows sunken PlusMinus screws to be accessed and actuated,
Design: Combination proﬁle Phillips/slotted, blade zinc-phosphated
165 i PZ/S VDE Insulated screwdriver for PlusMinus
screws (Pozidriv/slotted)
Application: For PlusMinus screws (Pozidriv*)
/slotted)
Design: PlusMinus (Pozidriv*)
/slotted)
*)
Reduced blade diameter with
integrated protective insulation, allows
sunken screws and spring elements to
be accessed and actuated, individually
tested as per IEC 60900 : 2004.
VDE Insulated screwdriver for slotted
screws with reduced blade diameter
162 i PH/S VDE Insulated screwdriver for PlusMinus
screws (Phillips/slotted)
Design: PlusMinus (Phillips/slotted)

?
Code mm mm
05006465002 # 1 80 98 3 1
/8
" 5
05006466002 # 2 100 105 4" 5
Code mm mm
05006181002 TX 5 80 81 3 1
/8
" 5
05006182002 TX 6 80 81 3 1
/8
" 5
05006183002 TX 7 80 81 3 1
/8
" 5
05006184002 TX 8 80 81 3 1
/8
" 5
05006169002 TX 9 80 81 3 1
/8
" 5
05006170003 TX 10 80 81 3 1
/8
" 5
05006172003 TX 15 80 98 3 1
/8
" 5
05006174003 TX 20 80 98 3 1
/8
" 5
05006176003 TX 25 100 105 4" 5
05006177002 TX 27 100 105 4" 5
05006178003 TX 30 100 105 4" 5
05006179002 TX 40 150 112 6" 5
Code mm mm mm
05004650002 2.5 80 98 3 1
/8
" 5
05004655002 3.0 80 98 3 1
/8
" 5
05004660002 4.0 80 98 3 1
/8
" 5
05004665002 5.0 80 105 3 1
/8
" 5
05004670002 6.0 100 105 4" 5
05004675002 8.0 100 112 4" 5
Code mm mm
05004780003 # 1 80 98 3 1
/8
" 5
05004783002 # 1 150 98 6" 5
05004781003 # 2 100 105 4" 5
05004784002 # 2 200 105 8" 5
05004782002 # 3 150 112 6" 5
97
All Kraftform Plus screwdrivers are
marked with their drive proﬁle and
size. This enables faster and more
reliable selection of the correct tool
from the tool case.
How to ﬁnd the correct
screwdriver quickly
165 iS PZ/S VDE Insulated screwdriver for PlusMinus
screws (Pozidriv/slotted) with reduced blade diameter
Application: For PlusMinus screws (Pozidriv*)
/slotted)
allows sunken PlusMinus screws to be accessed and actuated,
Design: PlusMinus (Pozidriv*)
/slotted), blade zinc-phosphated
*)
167 i VDE Insulated TORX®
screwdriver
Application: TORX®
socket screws
Design: Zinc-phosphated
164 i VDE Insulated hexagon screwdriver
168 i VDE Insulated screwdriver for square socket head
screws
Application: Square socket head screws
VDE Tools

?
Code mm mm mm mm
05005300004 5.5 125 98 11.0 5" 5
05005305002 6.0 125 98 12.0 5" 5
05005310003 7.0 125 105 14.0 5" 5
05005315002 8.0 125 105 15.0 5" 5
05005320003 9.0 125 105 16.0 5" 5
05005325002 10.0 125 112 17.0 5" 5
05005330003 11.0 125 112 19.0 5" 5
05005335003 12.0 125 112 20.0 5" 5
05005340003 13.0 125 112 21.0 5" 5
05104900002 3
/16
" 125 98 11.0 5" 10
05345280001 7
/32
" 125 98 12.0 5" 10
05104905002 1
/4
" 125 98 13.0 5" 10
05104901003 5
/16
" 125 105 15.0 5" 10
05104906003 3
/8
" 125 105 17.0 5" 10
05104902003 7
/16
" 125 112 19.0 5" 10
05104904002 1
/2
" 125 112 21.0 5" 10
05104903002 9
/16
" 125 112 23.0 5" 10
05104907002 5
/8
" 125 112 25.0 5" 10
Code mm mm mm mm
05005655008 0.5 3.0 70 3.0 1
/8
" 2 3
/4
" 5
Code
05006145006 1160 i VDE 1 x 0.4x2.5x80 1)
; 1 x 0.6x3.5x100;
1 x 0.8x4.0x100; 1 x 1.0x5.5x125
162 i PH VDE 1 x PH 1x80; 1 x PH 2x100
98
Wera produces the Kraftform handle
out of several materials with diﬀerent
properties. A resistant plastic is used
for the core which ensures that the
blade is held securely even under
high strain. A softer material is used
for the coloured soft zones, which
provides high frictional resistance and allows the transfer of
high forces – resulting in less required screwdriving eﬀort. The
red sections with their hard surfaces prevent any "sticking" of
the hand to the handle, making rapid repositioning of the hand
possible.
made out of several components?
190 i VDE Insulated nutdriver
Blade: Insulated, individually inspected as per IEC 60900 : 2004
247 UL Single-pole voltage tester
Application: Voltage testing
Standard: ISO 57680/6 and VDE 0680/6 for 80 to 250 V
160 i/6 Rack Screwdriver Set Kraftform Plus Series 100
+ Rack
Kraftform: The safety screwdriver. Lasertip blade + rack
Application: For slotted and Phillips screws
Content: 6-pieces set and rack in display carton
1)
without Lasertip

?
Code
05073600002 1162 i PH/S VDE 1 x # 1x80; 1 x # 2x100
Code
05073601003 1165 i PZ/S VDE 1 x # 1x80; 1 x # 2x100
99
VDE tools are often used under
extreme conditions, such as very
low temperatures. Safety must
be guaranteed even under these
conditions. The plastics used for the
handle of Wera VDE screwdrivers
are guaranteed to meet the most
stringent test requirements for
low-temperature impact strength
at -40 °C.
Where can I ﬁnd tools that are
resistant to extreme temperatures?
162 i PH/S # 1+2 Screwdriver set
Content: 2-piece set in display pack
165 i PZ/S # 1+2 Screwdriver set
Application: PlusMinus screws (Pozidriv*)
/slotted)
Content: 2-piece set in display pack
*)
VDE Tools

Code
05347777001 1160 i VDE 1 x 0.6x3.5x100; 1 x 1.0x5.5x125
162 i PH VDE 1 x PH 1x80; 1 x PH 2x100
168 i VDE 1 x # 1x80; 1 x # 2x100
?
Code
05347900001 1160 i VDE 1 x 0.4x2.5x80 1)
; 1 x 0.5x3.0x100 1)
;
1x0.6x3.5x100;1x0.8x4.0x100;1x1.0x5.5x125;
1 x 1.2x6.5x150
162 i PH VDE 1 x PH 0x80 1)
; 1 x PH 1x80; 1 x PH 2x100;
1 x PH 3x150
168 i VDE 1 x # 1x801)
; 1 x # 2x1001)
Code
05346279001 11440 1 x 4.5 - 6.0x41.0
1442 1 x 6.5 - 8.0x41.0
160 i VDE 1 x 0.8x4.0x100; 1 x 1.0x5.5x125;
1 x 1.2x6.5x150
162 i PH VDE 1 x PH 1x80; 1 x PH 2x100
168 i VDE 1 x # 2x100
247 UL 1 x 0.5x3.0x70
100
160 i/168 i/6 Rack Screwdriver set Kraftform Plus
Series 100 + Rack
Kraftform: The safety screwdriver. Lasertip blade + rack
Application: For slotted, Phillips and square socket screws
All Kraftform screwdrivers have a
non-roll feature at the lower end of
the handle. The hexagonal design
prevents any annoying rolling away of
the screwdriver at the workplace.
How to prevent the screwdriver
from rolling away
160 i/12 screwdriver set Kraftform Plus Series 100
Kraftform: The safety screwdriver with Lasertip blade
Application: Slotted, Phillips and square socket head
screws
1)
without Lasertip
160 i/162 i/168 i/7 Rack Screwdriver set Kraftform
Plus Series 100 + voltage tester+ rack + screw gripper
Kraftform: The safety screwdriver. Lasertip blade + screw
gripper + voltage tester + rack
Application: Slotted, Phillips and square socket head screws, screw gripper
with holding function for screws; ﬁxes all screw proﬁles and
sizes securely to the screw
*)

Code
05073690002 51440 1 x 4.5 - 6.0x41.0
1442 1 x 6.5 - 8.0x41.0
162 i PH VDE 1 x PH 1x80; 1 x PH 2x100
Code
05345200001 1190 i VDE 1 x 7/32"x125; 1 x 1/4"x125;
1 x 5/16"x125; 1 x 3/8"x125; 1 x 1/2"x125
Code
05345201001 1190 i VDE 1 x 3/16"x125; 1 x 7/32"x125;
1 x 1/4"x125; 1 x 5/16"x125; 1 x 3/8"x125;
1 x 7/16"x125; 1 x 1/2"x125
?
101
162 PH1/2 + 1440/1442 SB Screwdriver set
hexagon blades with a diameter from 2.5 mm to 4.5 mm and
4.5 mm to 6 mm
Construction: Elastomer
190 i/5 Nutdriver set Kraftform Plus Series
Kraftform: The safety screwdriver
190 i/7 Nutdriver set Kraftform Plus Series
Kraftform: The safety screwdriver
Our screwdrivers are tested for
dielectric strength under a 10,000 volt
load in a water bath to make sure that
their most important property, their
insulation, has been exhaustively
tested. Each individual Wera VDE
screwdriver is subjected to this test to
guarantee safe working up to
1,000 volts.
Where can I ﬁnd a safe
VDE screwdriver?
VDE Tools

103
The tools can be stored and carried
in a robust belt pouch, keeping them
always to hand.
The handle/interchangeable blade
system allows rapid exchange of the
blades required for a wide range of
applications.
Each Kraftform Kompakt VDE set has
been tested individually in a water
bath at 10,000 volts, in accordance
with DIN EN 60900 (IEC 60900:2004).
This ten-times-higher testing load
guarantees safe working at their
maximum permitted load of 1,000
volts.
The 18-piece set includes blades for
PlusMinus screws, various keys for
switch cabinets and a voltage tester.
Kraftform Kompakt VDE sets come with
an insulated handle and insulated
interchangeable blades, that can be
exchanged without any special tools.
Versatile tools for work on live wiring
VDE Tools

?
Code
05003470003 1817 VDE 1 x 9x102
KK 60 i 1 x 0.4x2.5x154; 1 x 0.6x3.5x154;
1 x 0.8x4.0x154; 1 x 1.0x5.5x154
KK 62 i 1 x PH 1x154; 1 x PH 2x154
Code
05003473002 1817 VDE 1 x 9x102
KK 60 i 1 x 0.6x3.5x154; 1 x 1.0x5.5x154
KK 62 i 1 x PH 1x154; 1 x PH 2x154
KK VDE 68 i 1 x # 1x154; 1 x # 2x154
Code
05003471008 1817 VDE 1 x 9x102
247 UL 1 x 0.5x3.0x70
KK 60 i 1 x 0.4x2.5x154; 1 x 0.6x3.5x154;
1 x 0.8x4.0x154; 1 x 1.0x5.5x154
KK 62 i 1 x PH 1x154; 1 x PH 2x154
KK 62 i PH/S 1 x # 1x154; 1 x # 2x154
KK 65 i PZ 1 x PZ 1x154; 1 x PZ 2x154
KK 65 i PZ/S 1 x # 1x154; 1 x # 2x154
KK 96 VK 6,3 1 x 6.3x89
KK 97 VK 8,1 1 x 8.1x89
KK 98 DK 1 x 89
KK 99 FL 1 x 89
104
Kraftform Kompakt VDE sets come with
an insulated handle and insulated
interchangeable blades, that can be
exchanged without any special tools.
Kraftform Kompakt VDE sets
Versatile tools for work on live wiring
Kraftform Kompakt VDE 60 i/7
1 Kraftform hand-held bit holder 817 VDE for Wera interchangeable blades
VDE interchangeable blades (each 154 mm long)
7-piece set
Kraftform Kompakt VDE 60 i/68 i/7
1 Kraftform hand-held bit holder 817 VDE for Wera VDE interchangeable blades
7-piece set
Kraftform Kompakt VDE 60 i/62 i/65 i/18
1 Kraftform hand-held bit holder 817 VDE for Wera VDE interchangeable blades
Single-pole voltage tester
18-piece set

Wera Screwdrivers Catalog

Recommandé

Recommandé

Contenu connexe

Tendances

Tendances (20)

Similaire à Wera Screwdrivers Catalog

Similaire à Wera Screwdrivers Catalog (20)

Plus de Carbide Processors

Plus de Carbide Processors (16)

Dernier

Dernier (9)

Wera Screwdrivers Catalog