Kdc bt8044 u

CD-RECEIVER

KDC-BT8044U
KDC-BT8044UY
KDC-W7544U
KDC-W7644UY
KDC-W7044U
KDC-W7144UY
INSTRUCTION MANUAL

© B64-4421-00/00 (EW/E2W)

Contents

Before use 3 Audio Adjustments 27
Audio Control
Basic Operation 4 Audio Setup
Hands-free phoning
Sound Setup 28
Function Control 6 Cabin selection
Display Settings 11 Speaker setting
DTA (Digital Time Alignment) setting
Display Type Selection X’Over setting
Text Display Selection Preset Equalizer curve select
Illumination Color Selection Manual Equalizer Control
Auxiliary Input Display Setting Preset position selection
Music disc/Audio file Operation 14 Manual position setting
Audio Preset Memory
Music Search Audio Preset Recall
Music Search for iPod
Searching for Music by Initial Favorite Control 33
All Random Favorite Preset Memory
iPod Control by Hand Mode Favorite Preset Recall
Direct Music Search Favorite Preset Memory Delete
Direct Disc Search Favorite Name Setting
Basic Operation of Disc Changer (Optional)
Bluetooth Setup 35
Tuner Operation 17
Registering Bluetooth device
Auto Memory Entry Registering Special Bluetooth device
Station Preset Memory Registering PIN Code
Preset Tuning Downloading the Phone Book
Direct Access Tuning Selecting the Bluetooth device You Wish to Connect
PTY (Program Type) Deleting a Registered Bluetooth device
Program Type Preset Displaying the Firmware Version
Changing Language for PTY Function Adding a voice dialing command
Operation of hands-free phoning 19 Setting a Voice Command for Category
SMS (Short Message Service)
Before Use Downloading the SMS
Receiving a call
During a call Basic Operations of remote control 40
Call waiting
Other functions Appendix 42
Making a call
Dial a number Accessories/ Installation Procedure 47
Speed dialing (Preset dial)
Calling a number in the Phone Book
Connecting Wires to Terminals 48
Calling a number in the call log Installation/Removing the Unit 49
Make a voice dialing call
Registering to the Preset Dial Number List Troubleshooting Guide 51
Display of phone number type (category)
Bluetooth Audio Operation 23 Specifications 54
Before Use
Basic Operation
Other Functions 24
Activating Security Code
Deactivating Security Code
Manual Clock Adjustment
Date Adjustment
Date Format Selection
AMP Control
Demonstration mode setting
Theft Deterrent Faceplate

2 | KDC-BT8044U/ KDC-BT8044UY/ KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/ KDC-W7144UY

Before use

2WARNING • If you experience problems during installation,
To prevent injury or fire, take the following consult your Kenwood dealer.
precautions: • When you purchase optional accessories, check with
• To prevent a short circuit, never put or leave any your Kenwood dealer to make sure that they work
metallic objects (such as coins or metal tools) inside with your model and in your area.
the unit. • Characters that conform to ISO 8859-1 can be
displayed.
Do not use this unit before canceling • Characters that conform to ISO 8859-5 or ISO 8859-
1 can be displayed. Refer to “MENU” > “Russian” of
Demonstration mode!
<Function Control> (page 6).
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the • The RDS feature won’t work where the service is not
<Demonstration mode setting> (page 26). supported by any broadcasting station.
• In this document, the description indicator will light
means a status is displayed. Refer to <Display Type
How to reset your unit
Selection> (page 11) for the details of the status
• If this unit or the connected unit (disc auto changer,
display.
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset • The illustrations of the display and the panel
button is pressed. appearing in this manual are examples used to
explain more clearly how the controls are used.
Reset button Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.

Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
Cleaning the Unit • Clean from the center of the disc and move
If the faceplate of this unit is stained, wipe it with a outward.
dry soft cloth such as a silicon cloth. • When removing CDs from this unit, pull them out
If the faceplate is stained badly, wipe the stain off with horizontally.
a cloth moistened with neutral cleaner, then wipe it
• If the CD center hole or outside rim has burrs,
again with a clean soft dry cloth.
use the CD only after removing the burrs with a
¤ ballpoint pen etc.
• Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or CDs that cannot be used
using a volatile liquid such as thinner or alcohol may scratch • CDs that are not round cannot be used.
the surface or erases characters.

Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
• CDs with coloring on the recording surface or CDs
Lens Fogging that are dirty cannot be used.
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the • This unit can only play the CDs with
.
CD player of the unit. Called lens fogging, this This unit may not correctly play discs which do not
condensation on the lens may not allow CDs to play. have the mark.
In such a situation, remove the disc and wait for the • You cannot play a CD-R or CD-RW that has not
condensation to evaporate. If the unit still does not been finalized. (For the finalization process refer to
operate normally after a while, consult your Kenwood your CD-R/CD-RW writing software, and your CD-R/
dealer. CD-RW recorder instruction manual.)
English | 3

Basic Operation
Release [ ] [SRC] Microphone

AUX

Auxiliary [ ] [AUD] [FNC] Control USB Terminal
input [TI] knob

General functions Auxiliary input
Connect a portable audio device with mini-plug
Power/Source Select button: [SRC] cable (3.5 ø).
Turns on the power.
When the power is ON, select a source. ⁄
SRC Select mode 1: Press the [SRC] button and then • Use the mini-plug cable which is stereo type and does not
have any resistance.
turn the Control knob or push it toward up or down.
• The auxiliary input requires the setting made in “MENU” >
To determine the selected source, press the Control
“AUX” of <Function Control> (page 6).
knob.
SRC Select mode 2: Pressing this button each time Text/Title scroll: Control knob
switches between sources. Scrolls the CD and audio file text display when
Tuner (“TUNER”) , USB or iPod (“USB” or “iPod”), pushing toward up for at least 2 seconds.
CD (“CD”) , Auxiliary input (“AUX”), and Standby Muting volume upon reception of phone call
(“STANDBY”) When there is a call, “CALL” is displayed and the audio
Press at least 1 second to turn off the power. system is paused.
⁄ When the call ends, “CALL” disappears and the audio
• The SRC Select mode can be set in “MENU” > “SRC Select” of system comes back on.
<Function Control> (page 6). The audio system comes back on when [SRC] is
• Auxiliary input source is initially set to “OFF”. Set “Built in pressed during a call.
AUX” described in <Function Control> (page 6) to “ON”. ⁄
: Select “MENU” > “Built in AUX”
• To use the TEL Mute feature, you need to hook up the MUTE
• When an optional accessory is connected, the source name
wire to your telephone using a commercial telephone
for each device appears.
accessory. Refer to <Connecting Wires to Terminals> (page
• This unit automatically turns full power OFF after 20
48).
minutes lapses in Standby mode in order to save the
vehicle’s battery. The time until full power OFF can be set in Function Control : [FNC]
“Power OFF” of <Function Control> (page 6). Pressing this button allows you to set various
• When connection of the iPod is recognized, the source functions using the Control knob. Refer to <Function
display changes from “USB” to “iPod”. Control> (page 6).
• USB (iPod) source is recognized as CD source on the Category Function of setup item
connected unit. MENU Allows you to set up the environment.
Volume control: [AUD] knob SETUP Allows you to set up the display and color.
Turn the knob to adjust the volume. SOUND Allows you to set up the sound environment.
Subwoofer output: Control knob BT Allows you to set up the Bluetooth function.
Switches between ON (“SUBWOOFER ON”) and OFF — Allows you to set up the .
(“SUBWOOFER OFF”) each time pushing toward down
Favorite Control : Control knob
for at least 2 seconds.
• You can do this function when “SWPRE” in <Function
You can recall the various registered functions by
Control> (page 6) is set to “SW”. turning the Control knob.


For example, you can recall and playback the playlist ⁄
in iPod while listening to Tuner. • 3 inch (8 cm) CD cannot be used. Attempt to insert using
Refer to <Favorite Control> (page 33). an adapter can cause malfunction.
Disc ejection: [0]
Tuner functions ⁄
FM band: Control knob • You can eject the disc for 10 minutes after switching off the
Switches between FM1, FM2, and FM3 each time engine.
pushing toward up. USB device/iPod play: USB Terminal
AM band: Control knob Connecting a USB device starts playback.
Switches to AM when pushing toward down. ⁄
• For the playable audio file, media, and devices, refer to
Tuning: Control knob
<About Audio file> (page 42).
Changes the frequency when pushing toward left or
right. Pause and play: Control knob
Switches between pause and play each time this
⁄ button is pressed.
• Use the “MENU” > “SEEK” of <Function Control> (page 6) to
change the frequency switching. USB device removing: [0]
• During reception of stereo stations the “ST” indicator is ON. Press this button for 2 seconds or longer to select the
remove mode, and the remove the USB device.
Traffic information : [TI] During the remove mode, “USB REMOVE” is displayed.
• For KDC-BT8044U/ KDC-BT8044UY: Turns ON or OFF
the Traffic Information function when pressing for at Music search: Control knob
least 1 second. Changes the music when pushing toward left or right.
• For KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/ Fast reverses or forwards the music while keeping
KDC-W7144UY: Turns ON or OFF the Traffic pushing toward left or right. (No sound is output
Information function when pressing. while playing audio file.)
When the function is turned ON, “TI” indicator is ON. Folder search: Control knob
If traffic bulletin starts when the function is ON, Changes the folder containing the audio file when
“Traffic INFO” is displayed and traffic information is pushing toward up or down.
received. • For the operation on iPod, enter <Music Search for iPod>
⁄ (page 14) is first to enter the search mode.
• If the volume is adjusted during reception of traffic Search mode: [ ]
information, the adjusted volume is memorized After pressing [ ] button, you can quickly search
automatically. The memorized volume will be applied next songs with the Control knob. See <Music Search>
time the Traffic Information function is turned ON. (page 14) for details.

Disc & Audio file play functions Hands-free phoning
Drop open the faceplate: Release Microphone:
⁄ (Accessory of KDC-BT8044U/ KDC-BT8044UY)
The microphone for the hands free phone is supplied.
• Push the faceplate on the left side, and return it to its
former position. When your voice cannot be recognized due to the
low microphone volume or noises in the vehicle,
Disc play: Disc slot adjust the microphone settings by selecting “MENU”
Starts playing when a disc is inserted. >“Mic Gain” of <Function Control> and “MENU” >“NR
When a CD is inserted, the “CD-IN” indicator is ON. Level” of <Function Control> (page 6).

English | 5

Function Control
Functions in the table below can be set up by using Function Control.

1 Enter Function Control mode Displayed item is depending on currently selected
Press the [FNC] button. source or mode. The mark in Condition column
shows the condition to which the item is displayed.
2 Select a Function group. : Can be set in other than standby state.
Push the Control knob towards right or left. : Can be set in standby state.
Pushing the Control knob towards left allows you : Can be set while Audio file source of CD/USB/iPod.
to set the preference items (“MENU”, “SETUP”, or : Can be set while Audio file source of CD/USB
“SOUND”). (excluding iPod).
Pushing the Control knob towards right allows you : Can be set while CD/ Disc changer source.
to set the currently selected source function item : Can be set while CD source.
: Can be set while Disc changer source.
ON/OFF.
: Can be set during Tuner source.
3 Select your desired setup item : Can be set during FM reception.
: Can be set while accessing AUX source.
Operation type Operation
: Can be set only during playback of the iPod source.
Movement between items Turn the Control knob. : Can be set for sources other than the standby
Selection of item Press the Control knob. source by setting “2 ZONE” of <Audio Setup> (page
Return to previous item Press the [FNC] button. 27) to “ON”.
Select “Return” at the bottom of the item list. : Can be set while a cell-phone is connected.
Repeat selection and determination until your : Sets “ILM MSC SYNC” in the menu to “OFF”..
: Refer to the reference page.
desired setup item is selected.
— : Can be set during all sources.
Example:
The Control knob is used for entry, but how to use
the knob varies depending on the setting items.
: Press the Control knob to switch the settings.
: Push the Control knob towards left or right to
switch the settings.
: Turn the Control knob to switch the settings.
1 sec. : Press the Control knob for 1 second to enter into
the setting mode.
In this manual, the above selection is 2 sec. : Press the Control knob for 2 seconds to enter into
indicated as the setting mode.
Select “MENU” > “DEMO Mode”.
Each item’s ”&” will be ”✓” when the source function ⁄
is set to ON. • Refer to the respective page for information on how to
set the items with reference page number.
4 Make a setting • Only the items available to the current source are
Push the Control knob towards up or down. displayed.
Press the Control knob to set the source function • The “SOUND” setting cannot be performed while the
item ON/OFF. Dual Zone function is used.
• Some items require you to keep pressing the
Control knob for 1 or 2 seconds so that you can
make a setting. For these items, the time during
which you need to keep pressing the Control
knob is displayed in the Entry column in seconds.
*Factory setting
• For the functions accompanied by the * Function of KDC-BT8044U.
description of the setting procedure and so forth, * Function of KDC-BT8044UY.
* Function of KDC-W7544U.
the reference page numbers are displayed. * Function of KDC-W7644UY.
* Function of KDC-W7044U.
5 Exit Function Control mode * Function of KDC-W7144UY.
Press the [FNC] button for at least 1 second. * Refer to <Menu Glossary> (page 44).


Source function item
Function Setting Entry Setting overview Condition Page
“iPod BY HAND” “ON”/ “OFF”* When set to “ON”, allows you to operate iPod with the 15
control on the iPod.
“FILE SCAN” “ON”/ “OFF”* When set to “ON”, plays the intro of the music in the —
folder successively.
“FOLDER RDM” “ON”/ “OFF”* When set to “ON”, plays the music in the folder —
randomly.
“ALL RANDOM” “ON”/ “OFF”* When set to “ON”, all songs in iPod are played at 15
random.
“FILE REPEAT” “ON”/ “OFF”* When set to “ON”, plays the music repeatedly. —

“FOLDER REP” “ON”/ “OFF”* When set to “ON”, plays the music in the folder —
repeatedly.
“TRACK SCAN” “ON”/ “OFF”* When set to “ON”, plays the intro of the music on the —
disc successively.
“DISC RANDOM” “ON”/ “OFF”* When set to “ON”, plays the music on the disc randomly. —

“MAGAZINE RDM” “ON”/ “OFF”* When set to “ON”, plays the music in the disc changer —
randomly.
“TRACK REPEAT” “ON”/ “OFF”* When set to “ON”, plays the music repeatedly. —

“DISC REPEAT” “ON”/ “OFF”* When set to “ON”, plays the music on the disc —
repeatedly.
“PTY SEARCH” Select the Program Type and search for a station. 18

“AUTO MEMORY” Memorizes 6 stations with good reception 17
automatically.

Preference item
Category Item Setting Entry Setting overview Condition Page
“MENU” “Security Set”/ — Sets/Resets security code. 24
1 sec.
“Security Clear”
“SRC Select” “1”*/ “2” Sets the source selection method. *
“Skip Search” “0.5%”*/ Sets the ratio of skip performed with <Music Search 14
“1%”/ “5%”/ for iPod>.
“10%”
“Device Regist”** — 1 sec. Register a Bluetooth device (pairing). 35
“SPCL DVC Select”** — Allow registration of a special device that cannot be 35
1 sec.
registered normally.
“Phone Selection”** — 1 sec. Select a cell-phone subject to hands-free connection. 36
“Audio Selection”** — 1 sec. Select the Bluetooth audio player to be connected — 36
“Device Delete”** — 1 sec. Cancel registration of the Bluetooth device. 37
“BT DVC Status”** — 1 sec. Display the status of the Bluetooth device. — *
“PIN Code Edit”** — Specify the PIN code required when registering this unit 36
1 sec.
using the Bluetooth device.
“Auto Answer”** “OFF”/ “0S” – Answer a call automatically after lapse of the preset *
“8S”* – “99S” time interval for automatic answer.
“Mic Gain”** “–2” – “0”* – Adjusts the sensitivity of the built-in microphone for a — *
“+2” telephone call.

Next page 3

English | 7

Function Control
“NR Level”** “–2” – “0”* – Reduces the noises generated by the surrounding — *
“+2” environment without changing the microphone
volume.
“SP Select”** “Front”*/ Specify the voice output speaker. *
“F-R”/ “F-L”
“Call Beep”** “ON”*/ “OFF” Output a beep from the speaker when a call comes in. *
“BT F/W Update”** — 1 sec. Display the firmware version and update the firmware. 37
“Beep” “OFF”/ “ON”* Setting the operation check sound (beep sound) ON/ —
OFF.
“Clock Adjust” — 1 sec. Sets the clock. — 25
“Date Adjust” — 1 sec. Sets the date. 25
“Date Mode” 7 types 1 sec. Sets the date display mode. 25
“SYNC” “OFF”/ “ON”* —

“DSI” “OFF”/ “ON”* DSI (Disabled System Indicator) of the unit blinks when —
the faceplate is removed.
“Illumi DIM” “OFF”/ “Auto”* Sets whether the illumination is dimmed in conjunction *
/ “MNAL1” / with the light switch of the vehicle or it is dimmed
“MNAL2” constantly.
“ILM Effect” “OFF”/ “ON”* KDC-BT8044U/ KDC-W7544U/ KDC-W7644UY: —
Sets whether the key illumination color is changed in
conjunction with the key operation.
KDC-BT8044UY/ KDC-W7044U/ KDC-W7144UY:
Sets whether the key illumination brightness is
changed in conjunction with the key operation.
“ILM MSC SYNC” “OFF”*/ “ON” KDC-BT8044U/ KDC-W7544U/ KDC-W7644UY: — —
Sets whether the key illumination color is changed in
conjunction with the sound volume.
KDC-BT8044UY/ KDC-W7044U/ KDC-W7144UY:
Sets whether the key illumination brightness is
changed in conjunction with the sound volume.
“Display” “OFF”/ “ON”* Turns off the display when no operation is performed. — *
“DISP DIM “ “OFF”/ “Auto”* Dims the display part in conjunction with the light *
/ “MNAL1” / switch of the vehicle.
“MNAL2”
“Contrast” “1” - “10” Adjusting the display contrast. —
“DISP N/P” “POSI 1”/ “2” Switches the panel display between positive or *
/ “NEGA 1”/ “2” negative.
“SWPRE”** “Rear”*/ Sets the preout output. *
“Sub-W”
“AMP” “OFF”/ “ON”* Turns on/off the built-in amplifier. *
“Zone2” “Rear”*/ “Front” Specifies the destination of AUX input sound when the *
Dual Zone function is turned on.
“AMP Control” — Controls the connected LX amplifier. — 25
“News” “OFF”*/ “00” Turns ON/OFF the News Bulletin Automatic Reception *
– “90” function and sets the news bulletin interrupt disabled
time.
“Local Seek” “OFF”*/ “ON” Only stations whose reception is good are searched in —
auto seek tuning.
“Seek Mode” “Auto1”*/ Selects the tuning mode of the radio. *
“Auto2”/
“Manual”


“AF” “OFF”/ “ON”* When station reception is poor, automatically switches *
to the station that is broadcasting the same program
over the same RDS network.
“Regional” “OFF”/ “ON”* Sets whether to switch to the station only in the —
specific region using the “AF” control.
“Auto TP Seek” “OFF”/ “ON”* When traffic information station reception is poor, —
automatically searches for a station that can be
received better.
“MONO” “OFF”/ “ON”* You can reduce the noise when stereo broadcasts are —
received as monaural.
“Name Set” — 1 sec. Sets the display when switched to AUX source. 13
“Russian”*** “OFF”/ “ON”* Selects Russian as the display language. *
“Scroll” “Auto”*/ Specifies whether the text is scrolled automatically. — —
“Manual”
“Favorite Delete” — 1 sec. Deletes Favorite Preset Memory. 33
“Built in AUX” “OFF”*/ “ON” Sets whether to display AUX during source selection. —
“Power OFF” “-----”/ Turns off the power when the preset time has lapsed in *
“20min”*/ the Standby mode.
“40min”/
“60min”
“CD Read” “1”*/ “2” Sets the CD read mode. *
“DEMO Mode” “OFF”/ “ON”* 2 sec. Specifies whether to enable demonstration. — 26
“SETUP” “Display “Ttpe Select” “DISP TYPE Sets the display pattern. — 11
Select” [A] – [D]”
“Graphic Select” “Graphic 1 –2” Sets the Type C spectrum analyzer display. — —
“Side Select” 3 types Sets the Type A side display. — —
“Text Select” — Sets the Type A/B/C text display. — 11
“Status” Appear/ Sets the Type A Status display. — 11
Disappear
“DISP Out — Sets the vehicle-side display when it is connected. — —
Select”***
“Color “All” “Variable Sets the panel and display illumination color. 12
Select”** Scan”*/
“Display” “Color 1” – Sets the display illumination color.
“Color 10”/
“Right” “User” Sets the right side of panel illumination color.
“Left” Sets the left side of panel illumination color.
“SOUND” “Control” “EQ” — Sets the sound quality. 30
“Bass Boost” “OFF”*/ Sets the Bass Boost level in two steps. —
“STEP1”/ “2”
“HIGHWAY- “OFF”/ “STEP1” Compensates the low volume or bass sound being lost *
SOUND” / “2”/ “3”* by road noises to make vocal sound clearer.
“Supreme+” “ON”*/ “OFF” Turns ON/OFF the Supreme plus function. *

“Position” — Compensates the sound environment in accordance 31
with the listening position.
“Setup” “Cabin” “Compact” etc. Selects the car type to compensate the distance 28
difference between each speaker.

Next page 3
English | 9

Function Control
“Speaker” — Sets the connected speaker, speaker size, and 28
installation position.
“DTA” — Makes fine adjustment of the compensation value 29
specified at Cabin.
“X’Over” — Makes fine adjustment of the X’Over value specified at 29
Speaker.
“Preset” “Recall” — Registering the value setup by Sound Control. Recalling 32
the sound setup registered by <Audio Preset Memory>.
“Memory” — Registering the value setup by Sound Control. 32
“DPS Set” “Bypass”/ Setting “BYPASS” passes the DSP function. —
“Through”* Setting “THROUGH” activates the DSP function.
“BT” “Voice Recognize” — Calls by recognizing the registered voice. 22

“Voice Tag” “PB Name Edit” — Registers voice for voice recognition. 38

“PN Type Edit” — Registers voice to select the Phone number category 38
in Phonebook.
“SMS” “SMS — Download a short message. 39
Download”
“SMS Inbox” — Display the received short message. 39

⁄
• The connected cell-phone must have the SMS function to
use the “SMS” function.
• Location played with “FILE SCAN”
- Audio file: First 10 seconds
- Music Editor media: First 10 seconds or the part picked by
Intro Skip.
During Intro Skip, turn the control knob left or right to
change the song.
The scan method depends on the Music Editor setting.
See the Music Editor help for details.


Display Settings

Display Type Selection Text Display Selection
Shown below are examples of display types. Changes displayed information on each source
Display Display Type following;
“TYPE [A]” Displays 4 to 5 lines of text. In Tuner source
“TYPE [B]” Displays a line of text and video. Information Display
“TYPE [C]” Displays a line of text and the spectrum analyzer. Frequency & Program Service name (FM) “Frequency/PS”
“TYPE [D]” Displays the clock. Title & Artist name* (FM) “Title/Artist”
Station name* (FM) “Station Name”
1 Enter Display type selection mode Radio text plus* (FM) “Radio Text Plus”
Select “SETUP” > “Display Select” > “Type Radio text (FM)* “Radio Text”
Select”. Frequency (MW,LW) “Frequency”
For how to select Function Control item, refer to Spectrum analyzer & Clock (“TYPE [A]/[B]”) “Speana/Clock”
<Function Control> (page 6). or Clock (“TYPE [C]”) or “Clock”
2 Select the Display type Date “Date”
Turn the Control knob. Blank “Blank”
* Information of Radio text plus is displayed.
3 Exit Display type selection mode
Press the [FNC] button.
In CD & External disc source
⁄ Information Display
• For how to switch the text display information, refer to Disc title “Disc title”
<Text Display Selection> (page 11). Track title “Track title”
• When “TYPE [A]” is selected, the status (ON/OFF indicator Play time “P-Time”
of each function) can be displayed on the first line, and Spectrum analyzer & Clock (“TYPE [A]/[B]”) “Speana/Clock”
the icon of the currently selected source and the text or Clock (“TYPE [C]”) or “Clock”
information title can be displayed on the left side by the Date “Date”
following <Function Control> (page 6) operation.
Blank “Blank”
Status display: Select “SETUP” > “Display Select” > “Status”
Side display: Select “SETUP” > “Display Select” >
In Audio file/ iPod source
“Side Select”
• When “TYPE [C]” is selected, the spectrum analyzer can Information Display
be switched by the following <Function Control> (page Title & Artist name “Title/Artist”
6) operation. Album & Artist name “Album/Artist”
: Select “SETUP” > “Display Select” > “Graphic Select” Folder name “Folder name”
File name “File name”
Play time “P-Time”
Play time bar (iPod only)* “Time Bar”
Spectrum analyzer & Clock (“TYPE [A]/[B]”) “Speana/Clock”
or Clock (“TYPE [C]”) or “Clock”
Date “Date”
Blank “Blank”
* Can be displayed only on the bottom line of “TYPE [A]”
text.
In Standby/ Auxiliary input source
Information Display
Source name “Source Name”
Clock “Clock”
Date “Date”
Blank “Blank”

Next page 3
English | 11

Display Settings

1 Enter Text display selection mode Function of KDC-W7544U/ KDC-W7644UY
Select “SETUP” > “Display Select” > Illumination Color Selection
“Text Select”.
Selecting the Illumination Color of the panel.
For how to select Function Control item, refer to
<Function Control> (page 6). 1 Enter Illumination color selection mode
2 Select the text display part Select “SETUP” > “Color Select”.
Push the Control knob towards up or down. For how to select Function Control item, refer to
The selected text display part blinks. <Function Control> (page 6).

3 Select the text 2 Select the place where you want to set the
Turn the Control knob. Illumination Color

4 Exit Function Control mode Place Display
Press the [FNC] button. All “All”
Display “Display”
⁄ Right “Right”
• If the selected display item does not have any Left “Left”
information, alternative information is displayed.
• When LX-AMP is connected, the item setup by the Turn the Control knob and push the center
Display mode of LX-AMP is displayed. when the desired item is displayed.
• Some items cannot be selected depending on the
display type and row.
3 Select the Illumination Color
• When selecting “Folder name” while playing with Turn the Control knob and push the center
iPod, names will be displayed depending on currently when the desired item is displayed.
selected browsing items. Select the color from “Variable Scan”/ “Color1” —
• If the iPod Control by Hand Mode is set to on while “Color 10”/ “User”.
playing the iPod, “iPod by Hand Mode” is displayed.
• If all characters cannot be displayed while playing with
Creating “User” color
iPod, the file number in the list is displayed. You can create your original color during the
Information Display selection from “Color1” — “Color10.”
Music title “TITLE***” The color you created can be called when you
Folder name “FLD***” select “User”.
File name “FILE***” 1. Press the Control knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
To select the color to adjust. Push the Control knob towards right
(red, green, or blue) or left.
To adjust color. Turn the Control knob or push it
(Range: 0 – 9) towards up or down.
3. Press the Control knob.
Exit the detail color adjustment mode.
4 Exit Illumination color selection mode


Auxiliary Input Display Setting
Selects the display when changing to Auxiliary
input source.

1 Select the AUX source
Press the [SRC] button.
2 Enter Auxiliary input display setting mode
Select “MENU” > “Name Set”.
For how to select Function Control item, refer to
3 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
4 Select the Auxiliary input display
Turn the Control knob.
“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”
5 Exit Auxiliary input display setting mode

⁄
• When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
• The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is
displayed by default.
• AUX source is initially set to “OFF”. Before display setting,
set “Built in AUX” described in <Function Control> (page
6) to “ON”.
: Select “MENU” > “Built in AUX”

English | 13

Music disc/Audio file Operation

Function of Audio file/ Internal CD source Function of iPod
Music Search Music Search for iPod
Selecting the music you want to listen to from the Search for the song (in iPod) you want to play.
device or media being played now.
1 Enter Music Search mode
1 Enter Music Search mode Press the [ ] button.
Press the [ ] button.
2 Search for music
“SEARCH” is displayed.
Displays the current Audio file name. Operation type Operation
Movement between items Turn the Control knob.
2 Search for music Skip Search *1 Push the Control knob towards right or left.
Audio file Selection of item Press the Control knob.
Return to previous item Push the Control knob towards up.
Return to Top menu Push the Control knob towards up for at
Movement between Turn the Control knob or push it towards least 1 second.
folders/files up or down.
Search by initial Push the Control knob towards down. Refer
Selection of folder/file Press the Control knob or push it towards to the next section <Searching for Music
right. by Initial>.
Return to previous folder Push the Control knob towards left.
Return to root folder Push the Control knob towards left for at Scroll bar is displayed on the right side of the
least 1 second. screen.
“8” or “7” beside the displayed folder name Cancelling the Music Search mode
indicates that this folder is preceded or followed by Press the [ ] button.
another folder. ⁄
File name is displayed with “¡” indicator. • *1 Skip Search: The number of songs to be skipped is
Internal CD source determined by the ratio of the total number of songs
in the list which is selected now. Set the ratio with
Operation type Operation “Skip Search” in <Function Control> (page 6). Keep
Movement between track Turn the Control knob or push it towards pushing Control knob for 3 seconds or longer skips
up or down. songs at 10% irrespective of the setting.
Selection of track Press the Control knob. • Characters that are included in a song name but cannot
Return to first track Push the Control knob towards left for at be displayed are left blank. If no character included in a
least 1 second. song name cannot be displayed, the browse item name
and digits are displayed.
Cancelling the Music Search mode Items Display Items Display
Press the [ ] button. Playlists “PLIST***” Podcasts “PDCT***”
⁄ Artists “ART***” Genres “GEN***”
• Music Search cannot be performed during Random play. Albums “ALB***” Composers “COM***”
Songs “PRGM***”

Function of iPod
Searching for Music by Initial
You can select an alphabetic character from the list
in the browse item (artist, album, etc.) selected now.

1 Enter Music Search mode


2 Start the alphabet search Function of iPod
Push the Control knob towards down. iPod Control by Hand Mode
“A B C …” is displayed.
Allows you to operate iPod with the control on the
• If you can not search for a song by an alphabetic
character in the browse item selected now, the data on iPod.
the screen does not change.
Enter iPod Control by Hand Mode
3 Select the initial to be searched for Select “iPod BY HAND”.
Operation type Operation For how to select Function Control items, refer to
Move to the next character. Turn the Control knob or push it towards <Function Control> (page 6).
right or left. ⁄
Move to the next row. Push the Control knob towards up or • iPod will be paused when Hand mode is turned ON
down. during playback.
• In the iPod Control by hand mode, iPod cannot be
4 Determine the selected initial operated using this unit.
Press the Control knob. • This mode is not compatible with music information
Start search. When search is completed, the music display. The display will show “iPod by Hand Mode”.
search mode is selected again at the selected • iPod can be operated when it conforms to the iPod
character position. control function.

Cancelling the alphabet search
Function of remote control
⁄
• The time of search by alphabet may become long Direct Music Search
depending on the number of songs in iPod or the folder Searchs the music by entering the track number.
structure.
• When selecting an initial in the alphabet search, entering 1 Enter the music number
“*” searches symbols and entering “1” searches digits. Press the number buttons on the remote
• If the first character string begins with an article “a”, “an”, control.
or “the” in the alphabet search mode, it is searched for in
defiance of the article. 2 Search the music
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [38] button.
Function of iPod
⁄
All Random • Direct Music Search cannot be performed during playing
All songs in iPod are played at random. of iPod, “Music Editor” media, Random play, or scan play.

Enter All random mode
Select “ALL RANDOM”.
For how to select Function Control items, refer to
⁄
• The time required to turn on the all random function
may become longer depending on the number of songs
in iPod or the folder structure.
• Turning on the all random function changes the iPod
browse item to “Songs”. This browse item will not change
even if the all random function is turned off.

English | 15

Music disc/Audio file Operation

Function of disc changers with remote control
Direct Disc Search
Searchs the disc by entering the disc number.

1 Enter the disc number
Press the number buttons on the remote
control.
2 Search the disc
Press the [FM+] or [AM–] button.
Cancelling Direct Disc Search
Press the [38] button.
⁄
• Direct Disc Search cannot be performed during playing
of Random play or scan play.
• Input “0” to select disc 10.

Basic Operation of Disc Changer
(Optional)
Selecting CD changer source
Select the “CD CHANGER” display.
Music search
Push the Control knob towards right or left.
Disc Search
Push the Control knob towards up or down.


Tuner Operation

Auto Memory Entry Preset Tuning
Putting stations with good reception in the memory Recalling the stations in the memory.
automatically.
1 Enter Preset Tuning Select mode
1 Enter Auto Memory Entry mode Press the [ ] button.
Select “AUTO MEMORY”.
2 Select a desired station in the memory
3 Recall the station
2 Open Auto Memory Entry Press the Control knob.
Turn the Control knob to select “YES”, and then
press the Control knob. Cancelling Preset Tuning
When 6 stations that can be received are put in the Press the [ ] button.
memory, auto memory entry closes.

Function of remote control
Station Preset Memory
Direct Access Tuning
Putting a station in the memory.
Entering the frequency and tuning.
1 Select the frequency to put in the memory
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
2 Enter Preset Memory mode control.
Press the [ ] button. “– – – –” is displayed.
3 Select the number to put in the memory 2 Enter the frequency
Turn the Control knob. Press the number buttons on the remote
4 Determine the number to put in the memory control.
Press the Control knob for at least 2 seconds. Example:

Cancelling the Preset Memory mode Desired frequency Press button
Press the [ ] button. 92.1 MHz (FM) [0], [9], [2], [1]
810 kHz (AM) [0], [8], [1], [0]

Cancelling Direct Access Tuning
control.
⁄
• You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.

English | 17

Tuner Operation

PTY (Program Type) Program Type Preset
Selecting the Program Type below and searching Putting the Program Type in the Preset button
for a station; memory and quick recall.
Program Type Display Program Type Display Presetting the Program Type
Speech “Speech” Serious Classical “Classics”
Music “Music” Other Music “Other M” 1 Select the Program Type to preset
News “News” Weather “Weather” Refer to <PTY (Program Type)> (page 18).
Current Affairs “Affairs” Finance “Finance” 2 Enter Program Type Preset mode
Information “Info” Children’s programs “Children” Press the [ ] button.
Sport “Sport” Social Affairs “Social”
Education “Educate” Religion “Religion” 3 Select the number to put in the memory
Drama “Drama” Phone In “Phone In” Turn the Control knob.
Culture “Culture” Travel “Travel” 4 Determine the number to put in the memory
Science “Science” Leisure “Leisure” Press the Control knob for at least 1 second.
Varied “Varied” Jazz Music “Jazz”
Pop Music “Pop M” Country Music “Country” Recalling the preset Program Type
Rock Music “Rock M” National Music “Nation M” 1 Enter PTY mode
Easy Listening “Easy M” Oldies Music “Oldies” Refer to <PTY (Program Type)> (page 18).
Music Folk Music “Folk M”
Light Classical “Light M” Documentary “Document” 2 Enter Program Type Preset mode
• Speech and Music include the Program type shown
below. 3 Select a desired Program Type in the memory
Music: Black character item. Turn the Control knob.
Speech: White character item.
4 Recall the Program Type
1 Select PTY mode Press the Control knob.
Select “PTY SEARCH”.
2 Select the Program Type Changing Language for PTY Function
Selecting the Program Type display language as
3 Search for the selected Program Type station follows;
Language Display Language Display
4 Exit PTY mode English “English” Norwegian “Norwegian”
Press the Control knob. Spanish “Spanish” Portuguese “Portuguese”
⁄ French “French” Swedish “Swedish”
• This function cannot be used during a traffic bulletin or Dutch “Dutch” German “German”
AM reception.
• When the selected Program Type is not found, “No PTY” 1 Enter PTY mode
is displayed. Select another Program Type. Refer to <PTY (Program Type)> (page 18).
2 Enter Changing Language mode
3 Select the language
4 Exit Changing Language mode


Function of KDC-BT8044U/ KDC-BT8044UY
KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/ KDC-W7144UY with KCA-BT200 (Optional Accessory)
Operation of hands-free phoning

Before Use your cell-phone to return to the hands-free talk mode.

• For details on the Bluetooth cell-phone with the Adjusting the Voice Volume during a Call
hands-free function, see <About the Cell-Phone> Turn the [AUD] knob.
(page 43).
• You need to register your cell-phone before using
it with this unit. For more details, see <Registering
Bluetooth device> (page 35).
• If you have registered two or more cell-phones, Call waiting
you need to select one of them. For more details,
see <Selecting the Bluetooth device You Wish to Answering Another Incoming Call with the
Connect> (page 36). Current Call Suspended
• To use the Phone Book, it must be downloaded to 1 Press the [AUD] button.
this unit in advance. For details, see <Downloading
the Phone Book> (page 36).
2 Turn the Control knob or push it towards up
or down. Select the “ANSWER” display.
• “BT” indicator is lit when a cell-phone is connected
to this unit. 3 Press the [AUD] button.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button or press the [ ] button
Receiving a call for at least 1 second.
Continuing the Current Call
Answering a Phone Call
Press the [AUD] button. 1 Press the [AUD] button.
⁄ 2 Turn the Control knob or push it towards up
• The following operations disconnect the line: or down. Select the “REJECT” display.
- Insert a CD. 3 Press the [AUD] button.
- Connect a USB device.
• The name of the calling party is displayed if it has already Answering the Waiting Call after Terminating
been registered in the Phone Book. the Current Call
Rejecting an Incoming Call for at least 1 second.
for at least 1 second. Switching between the Current Call and Waiting
Call
Press the [AUD] button.
Each pressing of this knob switches the calling
party.
During a call
Disconnecting a Call
for at least 1 second. Other functions
Switching to the Private Mode
Clearing the Disconnection Message
Press the Control knob.
KDC-BT8044U/ KDC-BT8044UY:
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/
⁄ KDC-W7144UY:
• Depending on the type of your cell-phone, switching Press the [ ] button for at least 1 second.
to the private talk mode may select the source that was “HF Disconnect” disappears.
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate
English | 19


Making a call Speed dialing (Preset dial)
1 Enter dialing method mode 1 Enter dialing method mode
KDC-BT8044U/ KDC-BT8044UY: KDC-BT8044U/ KDC-BT8044UY:
Press the [ ] button. Press the [ ] button.
KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/ KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/
KDC-W7144UY: KDC-W7144UY:
Press the [ ] button for at least 1 second. Press the [ ] button for at least 1 second.
2 Select a dialing method 2 Press the Control knob.
Press the Control knob. Select the “DIAL”, “PHONE BOOK”, “OUT-CALL”,
“DIAL” » “INITIAL” » “PHONE BOOK” » “OUT-CALL” » “IN-CALL”, or “MISSED CALLS” display.
“IN-CALL” » “MISSED CALLS” 3 Enter preset dial mode
Methods of operations in the above modes are Press the [ ] button.
described below.
4 Select the number you want to recall from the
3 Exit the dialing method mode memory
Press the [ ] button. Turn the Control knob or push it towards up or
down.
5 Press the Control knob.
Phone number is displayed.
Dial a number 6 Exit preset dial mode
1 Enter dialing method mode
KDC-BT8044U/ KDC-BT8044UY:
7 Make a call
KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/ ⁄
KDC-W7144UY: • You need to register the preset dial number. (page 22)
Press the [ ] button for at least 1 second.
2 Select the number dial mode
Select the “DIAL” display.
3 Enter a phone number
Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
4 Make a call
controller.
To erase the entered phone number digit by
digit:
Press the [4] button on the remote controller.
⁄
• You can input max 32 digits.


Calling a number in the Phone Book Calling a number in the call log
1 Enter dialing method mode 1 Enter dialing method mode
KDC-BT8044U/ KDC-BT8044UY: Press the [ ] button.
2 Select the call log mode
KDC-W7544U/ KDC-W7644UY/ KDC-W7044U/
KDC-W7144UY:
Select the “OUT-CALL” (outgoing call), “IN-CALL”
Press the [ ] button for at least 1 second.
(incoming call), or “MISSED CALLS” (missed call)
2 Select the Phone Book mode display.
3 Select a name or phone number
Select the “INITIAL” display, proceed to step 3.
Turn the Control knob or push it towards up or
Select the “PHONE BOOK” display, proceed to step
down.
4.
Switching between Display Modes
3 Select the initial to be searched for Press the [FNC] button.
Operation type Operation Pressing this button each time switches between
Move to the next character. Turn the Control knob or push it towards name and telephone number.
right or left.
Move to the next row. Push the Control knob towards up or 4 Make a call
down. Press the Control knob for at least 1 second.
Determine the selected initial. Press the Control knob. ⁄
• The outgoing call list and the incoming call list, and the
4 Select the name missed call list are the lists of calls originated from and
Operation type Operation received at this unit. They are not the ones stored in the
Move to the next phone Turn the Control knob or push it cell-phone memory.
number. towards up or down.
Move to the next name. Push the Control knob towards right
or left.

Switching between Display Modes
Pressing this button each time switches between
name and telephone number.
5 Make a call
⁄
• During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.

English | 21


Make a voice dialing call Registering to the Preset Dial Number
List
1 Enter voice recognize mode
Select “BT” > “Voice Recognize”. 1 Enter the phone number you wish to register
For how to select Function Control item, refer to Enter the phone number with reference to the
<Function Control> (page 6). following:
“Ready” is displayed. Dial a number/ Calling a number in the call log/
2 Press the Control knob. Calling a number in the Phone Book
“PB Name?” is displayed. 2 Enter Preset Memory mode
When a beep is heard, utter the name within 2 Press the [ ] button.
second.
3 Select the number to put in the memory
3 “PN Type” is displayed. Turn the Control knob or push it towards up or
When a beep is heard, utter the category within 2
down.
second.
4 Determine the number to put in the memory
4 Make a call Press the Control knob for at least 1 second.
• This step is the same as step 3 of the procedure in Exit the Preset Memory mode
<Calling a number in the Phone Book>. You can make a Press the [ ] button.
call or select a category.
⁄
• If your voice cannot be recognized, a message is
displayed. Pressing the Control knob allows you to retry Display of phone number type
voice input. (page 52) (category)
• Both the name and category requires registration of a
voice tag. (page 38)
The category items in the Phone Book are displayed
• Audio sound is not output during voice recognize. as follows:

Display Information
“GENERAL” / “ ” General
“HOME” / “ ” Home
“OFFICE” / “ ” Office
“MOBILE” / “ ” Mobile
“OTHER” / “ ” Other


Bluetooth Audio Operation

Before Use
• For details on the Bluetooth Audio player which
can be connected, see <About the Bluetooth Audio
player> (page 43).
• You need to register your Bluetooth Audio player
before using it with this unit. For more details, see
<Registering Bluetooth device> (page 35).
• You to select the Bluetooth audio player you wish to
connect. Refer to <Selecting the Bluetooth device
You Wish to Connect> (page 36).

Basic Operation
Selecting Bluetooth Audio source
Select the “BT Audio” display.
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
Pause and play
Music Search
⁄
• All or some of the operations above cannot be
performed if the Bluetooth audio player is not ready for
remote control.
• Switching between Bluetooth audio sources does
not start or stop playback automatically. Perform the
operation for starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.

English | 23

Other Functions

Activating Security Code Deactivating Security Code
⁄ To deactivate the Security Code function.
• You can set the Security Code with a 4 digit number of your 1 Select Security code mode
choice.
Select “MENU” > “Security Clear”.
• The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
1 Select Security code mode
Select “MENU” > “Security Set”. 2 Enter Security Code mode
For how to select Function Control item, refer to Press the Control knob for at least 1 second.
<Function Control> (page 6). When “Enter” is displayed, “[–][–][–][–]” is also
displayed.
2 Enter Security Code mode
Press the Control knob for at least 1 second. 3 Enter Security Code
When “Enter” is displayed, “[–][–][–][–]” is also Operation type Operation
displayed. Select the digits to enter Push the Control knob towards right
or left.
3 Enter Security Code Select the Security Code Turn the Control knob or push it
Operation type Operation numbers towards up or down.
Select the digits to enter Push the Control knob towards right
or left. 4 Press the Control knob for at least 3 seconds.
Select the Security Code Turn the Control knob or push it “Clear” is displayed.
numbers towards up or down. The Security Code function deactivates.
5 Exit Security Code mode
4 Confirm the Security Code Press the [FNC] button.
Press the Control knob for at least 3 seconds.
When “Re-Enter” is displayed, “[–][–][–][–]” is also
displayed.
5 Do the step 3 through 4 operation, and reenter
the Security Code.
“Approved” is displayed.
The Security Code function activates.
⁄
• If you enter the wrong Code in steps 3 through 4, repeat
from step 3.

6 Exit Security Code mode
Entering Security Code
The Security Code is required to use the audio unit
when the unit is first used after removed from the
battery power source or the Reset button is pressed.
1 Turn the power ON.
2 Do the step 3 through 4 operation, and enter
the Security Code.
“Approved” is displayed.
Now, you can use the unit.


Manual Clock Adjustment Date Format Selection
1 Select Clock adjustment mode 1 Select Date format mode
Select “MENU” > “Clock Adjust”. Select “MENU” > “Date Mode”.
For how to select Function Control items, refer to For how to select Function Control items, refer to
<Function Control> (page 6). <Function Control> (page 6).
2 Enter Clock adjustment mode 2 Enter Date format mode
Press the Control knob for at least 1 second. Press the Control knob for at least 1 second.
The clock display blinks. The date is displayed.
3 Adjusting Clock 3 Adjusting Date
Operation type Operation Turn the Control knob.
Selecting the item (hours or Push the Control knob towards right Select from 7 types.
minutes) or left. 4 Exit Date format mode
Adjust each item Turn the Control knob or push it Press the [FNC] button.
towards up or down.

4 Exit Clock adjustment mode
When LX AMP unit connecting
⁄
• You can do this adjustment when “MENU” > “SYNC” in AMP Control
<Function Control> (page 6) is set to “OFF”. You can control the LX AMP connected to the unit.

1 Select AMP Control mode
Select “MENU” > “AMP Control”.
Date Adjustment <Function Control> (page 6).

1 Select Date adjustment mode 2 Enter AMP Control mode
Select “MENU” > “Date Adjust”. Press the Control knob for at least 1 second.
For how to select Function Control items, refer to 3 Select the AMP Control item for adjustment
<Function Control> (page 6). Turn the Control knob or push it towards up or
2 Enter Date adjustment mode down.
Press the Control knob for at least 1 second. ⁄
The date display blinks. • For the details on the AMP Control item, see the
Instruction manual attached to the LX AMP.
3 Adjusting Date
4 Adjust the AMP Control item
Operation type Operation Push the Control knob towards right or left.
Selecting the item (month, day, Push the Control knob towards right
or year) or left. 5 Exit AMP Control mode
Adjust each item Turn the Control knob or push it Press the [FNC] button.
towards up or down.

4 Exit Date adjustment mode

English | 25

Kdc bt8044 u

Recommandé

Recommandé

Contenu connexe

Tendances

Tendances (20)

Similaire à Kdc bt8044 u

Similaire à Kdc bt8044 u (20)

Kdc bt8044 u