Configuring Sametime Unified Telephony Lite in IBM Connections
•Download as PPTX, PDF•
0 likes•415 views
The document discusses configuring and using Sametime Unified Telephony Lite (SUT Lite) within IBM Connections. SUT Lite allows for basic point-to-point calling between Sametime clients but has limitations compared to the full SUT capability. It requires enabling awareness in Sametime and configuring the SIP proxy on the Sametime media server to define routing rules for calls. Enabling SUT Lite for users involves configuring the necessary licenses, policies and dialplan to facilitate calls between Sametime softphones and other SIP endpoints.
Recommended
More Related Content
Similar to Configuring Sametime Unified Telephony Lite in IBM Connections
Similar to Configuring Sametime Unified Telephony Lite in IBM Connections (20)
Configuring Sametime Unified Telephony Lite in IBM Connections
- 1. Calling Sametime Adding telephony to IBM Connections ? Social Connections IV - 30/11/2012 - Amsterdam
- 2. Introduction What is SUT Lite Sametime and Connections SUT Lite and Connections
- 3. “What can I do with Sametime Unified Telefony Lite within IBM Connections”
- 4. Introduction What is SUT Lite Sametime and Connections SUT Lite and Connections
- 5. What is SUT Lite
- 6. Certified equipment http://www- 10.lotus.com/ldd/stwiki.nsf/dx/Sametime_Unified_Telephony_Lite_Inter operability_Testing_Program
- 7. Architecture
- 8. Limitations • Only point-to-point calls • Only Sametime Connect Client is supported • Users cannot dial into a Sametime meeting • NAT traversal is not supported.
- 9. SUT vs. SUT Lite
- 10. Introduction What is SUT Lite Sametime and Connections SUT Lite and Connections
- 11. Awareness Server Based Using Sametime Proxy Server Client Based Using the Sametime Connect Client
- 12. Client requirements • Sametime Client 8.0.2 + • When using SSL: • Sametime Connect 8.5 + • Lotus Notes 8.5.1 + • Users must be logged into Sametime from the same machine as where they access Connections and with the same account
- 13. Check the Client
- 14. Server configuration • Open the file profiles-config.xml • Locate the sametimeAwareness element • Set enabled to true • Restart Profiles
- 15. The Result
- 16. Introduction What is SUT Lite Sametime and Connections SUT Lite and Connections
- 17. Start a call
- 18. Calling
- 19. “What can I do with Sametime Unified Telefony Lite within IBM Connections”
- 20. ?
- 21. Introduction What is SUT Lite Sametime and Connections SUT Lite and Connections Configuring SUT Lite
- 22. Configure the server • Install the SUT Lite license • Enable SUT Lite on the Media Manager from the System Console • Optional: disable encryption
- 23. Enable users • Enable SIP Trunk capability on the Media Manager policy
- 24. Dialplan Dial String SIP endpoint Phone/Device 3118255517X Sametime Sametime Softphone 316XXXXXXXX FreePBX PBX (soft)phone @mcu.silverside.nl MCU Media Server Video Conferencing
- 25. Configure the SIP Proxy • In the System Console open the configuration of the SIP Proxies and Registrars of the Media Server • Open the Proxy Administration
- 26. Define the rules Configure the conditions
- 27. Define the rules Set the destination
- 28. Define the rules Example: Route all calls where the SIP Request URI starts with “+316” to 192.168.0.214 via TCP
- 29. Define the rules Example: Route all incoming calls from 192.168.0.214 to the Media Manager via TCP.
- 30. ?
Editor's Notes
- Wie ben ik, wat doe ik bij Silverside.ADOPTIE STRATEGIE Volgende slide
- When I heared what products were included with the IBM Connections Suite I understood most of them. They made sense. The only one that made me wondering was Sametime Unified Telephony Lite. This question will be the guideline through my session today. At the end I hope you can also answer this question.
- Introduced with 8.5.2Enable the SIP capabilities of Connect (softphone)Audio VideoMake and receive calls
- Direct SIP connection to the SIP Proxy of the Media ManagerNo additional hardwareNo additional software at clients
- 2 ways of connectingWhen combined only server based is usedOnlyConnect is support with SUTLite Client Based
- For SSL connections additional configuration of the client needs to be doneSSL is automatically used when Connections is accessed via HTTPS (mixed content)When using Lotus Notes the webapi of Connect needs to be enabled
- HTTP - Port 59449 HTTPS – Port 59669
- Awareness is only running with Profiles (profiles pages and business cards)When SSL is enabled for Connections, but not for Connect use HTTP for both urls
- Looking at the Driving Innovation video of the Connections Suite there should be a Call button. It’s not there. Only when using SUT it’s there and working as demonstrated.
- From my experience there is no real integration. Only for SUT. But having SUT Lite still has added value when used from Connect.
- Only a few 100K file with an install scriptTLS is fully supported, but it’s recommended to do the initial install without and enable afterwards
- Usually only INVITEFix available to prevent ST requests to route into the wrong direction
- “Push a route” to leave the Request URI and add a route field“Replace the Request-URL” to modify the URL. Req. For phonenumbers
- Not limited to numbering. You can also use names within the SIP Request. Usefull for non-telephony equipment
- Not limited to numbering. You can also use names within the SIP Request. Usefull for non-telephony equipment