THE WORKSHOP:
This workshop aims to familiarise the participants with the requirements laid down in the standard AS/NZS 3000:2007, commonly known as Australia-New Zealand Wiring Rules. For those installations covered in the scope of this standard, its provisions are mandatory and must be followed. Any engineer involved in planning and design of electrical systems, their installation or maintenance must have a clear idea about the various requirements contained in the standard.
The primary purpose of this standard, like many of its various other equivalent national standards, is to ensure the safety of personnel against the dangers arising from the use and handling of electrical equipment and appliances. The introductory modules of this workshop outline the basic principles that should be understood for a better appreciation of the standard. These include modules, which illustrate the calculation for the power demand of a system and the computation of earth fault current as discussed in the appendices of the standard, which are informative in nature but yet are very important in making an electrical system safe for operation. The actual provisions of the standard are then discussed in detail in the subsequent modules.
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur Escorts
Â
Practical Electrical Wiring Standards
1. Register NOW: Email the registration form to us at idc@idc-online.com
For more information contact 1300 138 522 or visit www.idc-online.com
Practical
Electrical Wiring
Standards â AS/NZS 3000:2007
MELBOURNE
18 & 19 May 2015
sydney
21 & 22 May 2015
Been to an IDC workshop before?
- Attend this workshop and youâll receive 5% off the registration price!
TechnologyTraining that Works
Roger Royal
Dip EE (C&G) Grad.Dip Rob.
Senior Engineer
A 2-day practical workshop presented by:
AUSTRALIA ⢠CANADA ⢠india ⢠IRELAND
Malaysia ⢠NEW ZEALAND ⢠SINGAPORE ⢠SOUTH AFRICA
UNITED KINGDOM ⢠UNITED STATES ⢠VIETNAM
EARLY BIRD
BOOKING OFFER
TOTAL VALUE TO YOU - $835
Book by 20 April 2015 and
you will receive 20% off the full
registration price + 4 ebooks
each with hundreds of pages of
engineering knowledge
4-for-3
BOOKING OFFER
plus
our
Only
$
1995 per person
including GST
⢠Practical HV Cable Jointing and
Terminations for Engineers and
Technicians
⢠Practical Electrical Substation
Safety
⢠Electrical Drawings and Schematics
⢠Practical Earthing, Bonding,
Lightning and Surge Protection
You will learn how to:
⢠Identify the various sections and requirements of the standards
⢠Understand these requirements and apply them in your day-to-day
functioning
⢠Appreciate the importance of fulfilling the requirements for safe use of
electrical equipment and systems
⢠Have a clear knowledge of earthing and its importance in safety
⢠Make simple calculations to check the adequacy of conductors and
protective earthing components to ensure safe operation
⢠List the periodic checks and verification measures to be carried out in an
electrical installation as mandated by the standard
who should attend:
⢠Building service designers
⢠Consulting engineers
⢠Data systems planners and
managers
⢠Electrical and instrumentation
technicians
⢠Electrical contractors
⢠Electrical engineers
⢠Electrical inspectors
⢠Electricians
⢠Instrumentation and control
engineers
⢠Maintenance engineers
⢠Power system protection and
control engineers
⢠Project engineers
⢠Safety professionals
2. Roger has built up a solid 40 years of hard won experience in the
electrical power industry and this is apparent in his instructing. He has
a passion for teaching and has achieved outstanding results over the
past ten years with his courses on circuit breakers and switchgear,
earthing, bonding, lightning, surge protection, power systems protection
and transformers throughout the world.
He commenced his career in the design and construction of transformers, power cables and
switchgear with Alstom (GEC); this work included a significant degree of R&D. Roger has since
worked for numerous blue chip companies in the classical design of power systems,
transformers and switchgear. More recently, he has spent considerable time in maintenance
operations of electrical engineering assets.
Roger has carefully prepared for the presentation of this workshop, to ensure that you will walk
away with the skills you can immediately apply to your work. He is looking forward to meeting
all participants and being able to pass on his experience and knowledge.
Practical Electrical Wiring Standards
An intensive, practical 2-day workshop presented by
Roger Royal Dip EE (C&G) Grad.Dip Rob. Senior Engineer
Free reference manual
as a hard-copy and eBook (Valued at $223.90)
Our delegates donât just receive photocopied notes!
You will receive the comprehensive fully illustrated reference manual,
as a hard-copy and eBook version, filled with hundreds of pages of
tables, charts, figures and handy hints.
Discount Offer
SAVE $1995
* discounted and free registration to be
used for the same workshop
in the same venue
Book four delegates
pay for three!
Register three people on a
public two-day workshop and
receive your fourth registration
FREE
About IDC Technologies
Visit our WEB SITE
www.idc-online.com to download
FREE software and technical information
With a portfolio of over 300 workshops
specialising in the fields of industrial data
communications, electrical and mechanical
engineering, automation and control, we have
trained over 500,000 engineers, technicians
and technologists over the last 20 years.
Wehaveanenthusiasticteamofprofessionals
in offices conveniently located around the
world, who are committed to providing the
highest quality of engineering and technical
training.
On-Site Training
All IDC Technologies training workshops are
available on an on-site basis, presented at
the venue of your choice, saving delegates
travel time and expenses, thus providing
your company with even greater savings.
SAVE MORE THAN 50% OFF
the per person cost!
2-day courses start from $6,000
FOR UP TO 6 PEOPLE and can be
customised to your needs.
Have the training delivered
WHEN AND WHERE you need it!
For more information or a FREE detailed
proposal contact:
Kevin Baker on 1300 138 522 or
email: training@idc-online.com
PLUS 5 eBooks of
your choice!
Every delegate will also receive
5 eBooks of their choice
from IDCâs technical library
â valued at $420!
the workshop
This workshop aims to familiarise the participants with the requirements laid down in the
standard AS/NZS 3000:2007, commonly known as Australia-New Zealand Wiring Rules. For
those installations covered in the scope of this standard, its provisions are mandatory and
must be followed. Any engineer involved in planning and design of electrical systems, their
installation or maintenance must have a clear idea about the various requirements contained
in the standard.
The primary purpose of this standard, like many of its various other equivalent national
standards, is to ensure the safety of personnel against the dangers arising from the use and
handling of electrical equipment and appliances. The introductory modules of this workshop
outline the basic principles that should be understood for a better appreciation of the
standard. These include modules, which illustrate the calculation for the power demand of a
system and the computation of earth fault current as discussed in the appendices of the
standard, which are informative in nature but yet are very important in making an electrical
system safe for operation. The actual provisions of the standard are then discussed in detail
in the subsequent modules.
Pre-requisites
A working knowledge of basic electrical engineering principles is required. Experience in
planning, installation and maintenance of electrical equipment and systems will enable the
workshop to be placed in context.
The fee for each workshop covers all materials
including workshop manual, lunches
and refreshments
practical sessions
This is a practical, hands-on workshop enabling you to work through exercises which reinforce
the concepts discussed.
To gain full value from this workshop, please bring your laptop/notebook computer.
Please bring a current copy of the AS/NZS3000:2007 Wiring Rules, either as a hard copy or
on your computer to the workshop.
3. â AS/NZS 3000:2007
The program
Day ONE
INTRODUCTION
⢠Evolution of electrical distribution systems
⢠Electrical insulation
⢠Current limits of conductors based on
insulation
⢠Current ratings based on installation
methods
⢠Earthing and its importance in safety
⢠Methods adopted for system earthing
⢠Earth fault sensing methods
⢠Other hazards
⢠AS/NZS 3000:2007 preface and contents
AS/NZS 3000:2007 STANDARD - SCOPE
AND DEFINITIONS
⢠Application areas
⢠Learning a few terms
⢠Alterations, additions and repairs
alternative arrangements
⢠Protection for safety
⢠Design of an electrical installation
⢠Selection and installation of electrical
equipment
⢠Inspection and testing
SELECTION AND INSTALLATION OF
SWITCHGEAR AND CONTROLGEAR
⢠Arrangement and control of electrical
installation
⢠Devices for isolation and switching
⢠Fault protection
⢠Devices for protection against overcurrent
and short circuit
⢠Coordination and discrimination
⢠Protection against earth leakage current,
overvoltage and undervoltage
⢠Switchboards
⢠Circuit arrangements, protection
coordination, limits of LV feeder lengths for
proper earth fault detection (as per AS/
NZS 3000:2007)
⢠Calculating the demand of electrical
systems for proper conductor sizing (as per
AS/NZS 3000:2007)
⢠The degree of protection of an item of
enclosed equipment (as per AS/NZS
3000:2007)
PRACTICAL WORK â CALCULATIONS
SELECTION AND INSTALLATION OF WIRING
SYSTEMS
⢠Types of wiring systems, external influences,
current-carrying capacity, sizing of conductors,
voltage drop considerations in sizing
⢠Electrical connections, identification of
wires and cables, installation, enclosure of
cables, underground wiring systems, aerial
wiring systems
⢠Cables supported by a catenary
⢠Emergency systems
⢠Busbar trunking systems and rising mains
⢠Earth sheath return system
⢠Sinking depth and sizes of support
structures for private aerial lines (as per
appendix D of AS/NZS 3000:2007)
⢠Application of the WS classification of
wiring systems in accordance with AS/NZS
3013 (as per appendix H of AS/NZS
3000:2007)
Day TWO
PRACTICAL WORK â CALCULATIONS
SELECTION AND INSTALLATION OF
APPLIANCES AND ACCESSORIES
⢠Protection against thermal effects
⢠Socket outlets
⢠Lighting equipment and accessories
⢠Cooking appliances
⢠Heaters
⢠Motors
⢠Capacitors
⢠Transformers
⢠Batteries
REQUIREMENTS FOR EARTHING IN
ELECTRICAL INSTALLATIONS
⢠Earthing arrangements
⢠Multiple Earthed Neutral (MEN) system
⢠Earthing conductors
⢠Earthing system components
⢠Equipment earthing and equipotential
bonding
⢠Earth fault loop impedance
⢠Earthing requirements for other (non-
electrical) systems
REQUIREMENTS FOR SPECIAL
ELECTRICAL INSTALLATIONS/ LOCATIONS
⢠Locations containing baths, showers or
other fixed water containers
⢠Swimming pools, paddling pools and spa
pools or tubs
⢠Locations containing sauna heaters
⢠Refrigeration rooms
⢠Locations where general hosing down
operations are carried out
⢠Fountains and water features
⢠Extra-low voltage electrical installations
⢠High voltage electrical installations
⢠Hazardous areas
⢠Emergency systems
⢠Requirements of AS/NZS 3000 within AS
2067 for HV installations
TESTING AND VERIFICATION
REQUIREMENTS OF THE STANDARD
⢠Visual inspection
⢠Testing
⢠Common inspection and test methods for
low voltage, Multiple Earthed Neutral
(MEN) electrical installation as per AS/
NZS 3017
⢠Periodic verification of existing electrical
installations of low voltage AC supply
system as per AS/NZS 3019
SUMMARY, OPEN FORUM
AND CLOSING
4. ABN 78 003 263 189
Web Site:
www.idc-online.com
Email:
idc@idc-online.com
Mail:
IDC Technologies
POâBox 1093
West Perth WA 6872
Fax:
1300 138 533
Register
Now:
Enquiries:
Phone:
1300 138 522
Practical Electrical Wiring Standards â AS/NZS 3000:2007
Workshop details
⢠Workshops start at 8:30am and finish at 5:00pm daily.
⢠Registration is from 8:00am on the first day.
⢠Theworkshopfeesareperdelegateandincludeareference
manual, handouts, lunches and all refreshments.
⢠Fullpaymentisrequiredpriortothecommencementofthe
workshop.
Early Bird BOOKINGâOffer
Please note that the Early Bird Booking Offer is only available
to those registrations received by 20 April 2015 and paid
prior to the commencement of the workshop.
Confirmation
Confirmation of receiving your registration will be sent within
48 hours. Official confirmation and details of the workshop
will be sent to you prior to the workshop date. Please wait for
official confirmation before making accommodation and/or
travel arrangements.
Cancellation
A fee of 20% will apply for written cancellations received
7-14 days prior to the commencement of the workshop.
Cancellations received less than 7 days prior to the workshop
are not refundable however substitutes are welcome.
Please Note
Venuestobeconfirmeduponregistration.Venuesaresubject
to change. Instructors may change without notice.
IDC Technologies has no affiliation with suppliers or
manufacturersandthereforepresentsacompletelyunbiased
factual view of the industry.
100% MONEY BACK GUARANTEE
IDC Technologiesâ engineers have put considerable time and
experience into ensuring that you derive the maximum value
from each workshop. If you feel by lunch time of the first day
that the workshop is not appropriate, please let us know so
that we can arrange a 100% refund of your fee.
Privacy Information
If your address details are incorrect, or you wish to remove
your name from our mailing list, please contact us by phone,
fax or email.
At times we make use of lists that cannot be cross-checked
against our own database and you may receive a duplicate.
If so, please pass this on to an interested colleague.
Continuing Professional Development (CPD)
This program is designed to meet your continuing
professional development requirements. A certificate
documenting your attendance will be awarded at the
end of the workshop. This serves as important evidence
of your continuing professional commitment to your
career. This workshop may count towards fulfilling
your Engineers Australia CPD obligations â Engineers
Australiaâs CPD Policy can be found at their website:
http://www.engineersaustralia.org.au/
Contact: Company Name:
Company Address:
Suburb: State: Post Code:
Phone: Fax: Email:
Mr/Ms: Job Title: Email:
Mr/Ms: Job Title: Email:
Mr/Ms: Job Title: Email:
Mr/Ms: Job Title: Email:
Should you have more people interested in attending this workshop, please contact us via email: idc@idc-online.com
Delegate Details
Attendees:
Melbourne - 18 & 19 May 2015
Hotel Ibis (on Therry Street), Melbourne
Sydney - 21 & 22 May 2015
Rydges Camperdown, Sydney
Please register by 27 April
to avoid disappointment
Workshop Details
Register three people on a public two-day workshop and
receive your fourth registration FREE
* discounted and free registration to be used for the same
workshop in the same venue.
Discount offer - save $1995
- book 4 delegates, pay for 3!
Received a brochure in the mail
Received an email from IDC
Searched online (Google, Yahoo etc)
Recommended by a friend/colleague
Other (please specify) ________________________
______________________________________________
How did you hear about this
workshop? (PLEASE TICK)
1
3
BOOKING FOR ONE DELEGATE: $1995 x ______ delegates = $______________
BOOKING FOR four DELEGATES: $1995 x ______ delegates = $______________
The fourth participant is FREE
Early bird booking offer: (if booking on or before 20 April 2015)
YES, I qualify and would like to receive my 4 FREE eBooks
PLUS 20% OFF the registration price less 20% = $______________
Total = $______________
On the reverse of your card, above the signature,
is a security number. In order to authorise your
card transaction, we require the last 3 digits:
If the Cardholder's address
is not the same as shown
above please tick this box:
Please Note: Full payment is required prior to the commencement of the workshop.
Payment Details Note: Prices are INCLUSIVE of GST
I wish to pay by Cheque, made payable to IDC Technologies
Company Order Number: __________________________________
Please charge my Mastercard Visa Expiry Date: ____/_____
______________________________________________________________
Cardholderâs Name:
Cardholderâs Signature
My billing information is the same as above in 'DELEGATE DETAILS'
Please send invoice to: Company Name:
Company Address:
Suburb: State: Post Code:
billing information (PLEASE invoice to)
1
3