SlideShare une entreprise Scribd logo
1  sur  11
Télécharger pour lire hors ligne
International Journal of Engineering Science Invention
ISSN (Online): 2319 – 6734, ISSN (Print): 2319 – 6726
www.ijesi.org Volume 2 Issue 12ǁ December 2013 ǁ PP.59-69

A Study of Zenner – Holomon Parameter Variation with Pass
Reduction in Steel Rolling
1,

Okediran, I.K., 2,Alamu, O.J. and 3,Durowoju, M.O.

Department of Mechanical Engineering, Osun State University, Osogbo, Nigeria.

ABRSTRACT : An attempt is made in this work to establish mathematical relationships between the Zener –
Hollomon Parameter and rolling reduction per pass in the hot rolling of Type 316 High Carbon Stainless Steel
(HCSS316). The hot rolling simulation of steel based on the Reverse Sandwich Model and that based on the
Sims‟ theory were used with the hot rolling experimental data for HCSS316, to generate results which reveal the
dependency of the two rolling parameters on each other. These results were then processed with the EXCEL
Package to arrive at a quantitative description of the observed relationship. The Zener–Hollomon parameter (Z)
was
found
to
be
a
non
linear
function
of
rolling
reduction
(r):
( Log 10Z   ar  br  cr  d ;...... a, b, c, d  cons tan ts ) for High Carbon Stainless Steel hot flat
rolled at low strain rates. The results compare favourably with experimental inferences.
3

2

KEY WORD: Zener-Hollomon Parameter, rolling reduction, simulation]
I.

INTRODUCTION

Rolling nowadays accounts for about 90% of all metals produced by metal working processes. It was
first developed in the late 1500s. Traditionally, the initial material form for rolling was an ingot. By far the
largest amount of finished steel production is achieved by rolling. The Semi-finished products cast from the
steelmaking furnace are reheated to the austenising range and passed through a series of mills with rolls of the
required profile to force the hot steel into the finished shape. (Graham, 1993) Developed in the mid – 1800s two
high and three high rolling mills are still used today for initial breakdown passes on cast ingots. However, this
practice is now being rapidly replaced by continuous casting and rolling, with much higher efficiency and lower
cost.The advent of continuous casters has necessitated hot flat rolling at low strain rates (0.01 – 1.55) s-1 and low
reduction ( 10%) (Aiyedun, 1986). Under such rolling condition, the contact time in the roll gap increases and
heat loss from the pre-heated ingot to the surroundings and the rolls increases. This variation in temperature
induces a non-uniform deformation pattern in the through-thickness of the rolled steel. The deformation, by
virtue of the un-even re-crystallization and grain refinement, as a result creates in the material a low-temperature
harder surface and a high-temperature softer core (Alamu and Aiyedun, 2003, Ojediran and Alamu, 2003).(see
Fig.1)The prevailing situation has been investigated by authors. Barbosa, (1983), Leduc, (1983), and Aiyedun
(1984) referred to the observed effect as “Reverse Sandwich” or Roll chilling, as the through-thickness hardness
variation presents a direct opposite of what obtains in a sandwich rolling process, where harder metals are
sandwiched between layers of softer metals to effect rolling of very hard and high strength metals into thin
strips without rupture in the rolls (Afonja and Sansome, 1973).
Studies abound in literatures on deformation in sandwich rolling and the reverse sandwich effect or roll
chilling. The adoption of computer simulation in modeling engineering systems further expands this area of
study. The Zener-Hollomon parameter is uniquely related to stresses, and gives an indication of deformation in a
material. Researchers (Zener and Hollomon, 1944; Aiyedun, 1984) have long established that deformation
increases with decreasing Zener – Hollomon parameter value. Alamu and Taiwo, (2002) employed computer
simulation to study deformation pattern in the hot rolling of High Carbon Stainless Steel type 316 (HCSSS316)
using a reverse Sandwich Model developed by Shobowale (1998). In the work, the reverse sandwich model was
simulated incorporating strain rate and Zener-Hollomon parameter computation for different zones along the
thickness of HCSS316 during hot flat rolling, thus permitting a study of the deformation pattern of this material
during hot rolling.In this work, the relationship between deformation rate, in terms of the Zener-Hollomon
parameter and rolling reduction per pass in the hot rolling of HCSS316 is investigated, using the reverse
sandwich model and Sims‟ theory of hot flat rolling, with hot flat rolling experimental data earlier obtained by
researchers for HCSS316.

www.ijesi.org

59 | Page
A Study Of Zenner – Holomon Parameter Variation…

II. MATERIALS AND METHOD
Deformation in hot rolling is temperature dependent. In this process the strength of a metal decreases as
temperature rises, and its grains can be distorted more easily. In line with Sims‟ theory, hot rolling process is
characterized by “sticking throughout the roll gap” (Sims, 1954). However, this is not entirely true for hot
rolling of HCSS316 at low strain rates; here, the rolling surfaces are sufficiently chilled leading to a mixed
sliding –sticking condition in the roll gap (Aiyedun, 1986).

THEORIES OF METAL ROLLING
Lennard (1980), and Usamah and Lennard (1980), amongst other literatures have reported that,
Orowan‟s theory is the most comprehensive among the many theories of rolling. According to Lennard, (1980),
the approach requires mathematical descriptions of material behaviour and deformation as well as assumptions
of frictional conditions at the roll – metal interface and mode of roll deformation. The complexity of the method
of solution of Orowan‟s equation caused later researchers, notably, Sims, Bland and Ford, Alexander, Alexander
and Ford and Atreya and Lennard to develop solutions based on simplifying assumptions.
1.

Orowan’s Theory:
According to Lennard, (1980) Orowan‟s theory can be summarized in the differential equation:

d
hs  2k   tan    2 R`s.sin    cos 
d
where:



……………..

(1)

interfacial shear stress,
roll pressure,
thickness of the strip in the roll gap,
yield strength in shear of the material,
current radius of curvature of the roll at a particular location,
independent variable (angle) measured from the centre line in the
roll gap.
The instantaneous yield stress, k, depends on rolling temperature, strain and strain rate, and must be determined
s
h
k
R`


=
=
=
=
=
=

before evaluating the mean yield stress, K , for subsequent computation of rolling parameters of interest such as
load and torque.
2.

Sims’ Theory of Hot Flat Rolling:

According to Sims (1954), the only practicable method of allowing for the elastic deformation of the rolls is that
due to Hitchcock, who replaced the actual distribution of pressure over the roll surface with an elliptical
distribution giving the same total load. The roll, in its arc of contact with the material, is then of constant radius
of curvature. Sims‟ hot flat rolling theory assumes a circular arc of contact, which is flattened in accordance
with Hitchcok‟s formular:

 C .P 
R` Ro1 

  .W 

……………………………… (2)

where:
R‟ = radius of curvature of the elastically deformed roll, (mm)
Ro = un-deformed roll radius, (mm),
P = vertical roll pressure, (N/mm2 )
W = width of the material, (mm),
C = constant, and,

C 8

1  v 
2

E

…………………………………(3)

also,

= 0.0223 mm2 kN-1 for steel rolls,
= 0.0247 mm2 kN-1 for chilled C.I. rolls
2
P =132KN/ mm (Sims, 1954; Aiyedun, 1984)
However, several authors have questioned the validity of this approach.

3.

The Bland and Ford’s Theory:

The Bland and Fords theory is basically a theory for cold rolling, where sliding takes place throughout the arc
of contact but has been found applicable to hot rolling of HCSS316, where there is a mixed sticking - sliding
condition (Aiyedun 1984). This is the situation for hot rolling of HCSS316 at (900 – 1200)oC, (0 – 15) %
reduction, (0.07 – 1.5) s-1 strain rates.

www.ijesi.org

60 | Page
A Study Of Zenner – Holomon Parameter Variation…
THE ROLL CHILLING EFFECT
A detailed description of the Reverse Sandwich Model based on the „Roll Chilling Effect‟, which
characterizes hot rolling of HCSS316 has been presented elsewhere; (Shobowale, (1998), Alamu, (2001), Alamu
and Aiyedun, (2003)). The reverse sandwich rolling presents a situation whereby a high strength - metal clads a
low strength metal. The strength variation being a direct consequence of drastic temperature changes during
rolling. The reverse sandwich model predicts rolling temperatures, temperature distribution corresponding to
different heights (17 Zones), the Zener-Hollomon parameter, yield stresses, rolling load and torque for
HCSS316 rolled at low strain rates and low reduction.
DEFORMATION IN MATERIAL AND ROLLING TEMPERATURE
Extensive research work has been carried out on deformation modeling using the Zener-Hollomon
parameter. A general drop in the Zener-Hollomon parameter from the rolling surfaces (lowest temperature zone)
towards the core (temperature peak) of the material was observed by Alamu and Taiwo, (2002), implying that
the material deforms increasingly towards the centre. The conclusion drawn was corroborated with the fact that
metals deform at a greater rate at elevated temperatures (Early, 1977)
PASS REDUCTION AND THE ZENER – HOLLOMON PARAMETER
Reduction per pass during metal rolling process is given as:
……………………………………. (4)
  Hf  Ho
where;  = rolling reduction, (mm),
Hf = final specimen thickness, (mm),
Ho = initial specimen thickness, (mm).
Expressed as a percentage, we have:

r

Hf  Ho
 100%
Ho

…………………………………… (5)

The Zener-Hollomon parameter was determined using the proposition of Zener and Hollomon, (1944):



 Q 



  f    exp
   f (Z )

RT 


……………………. (6)

 = strain rate
R = universal constant, (J /mol..K),
T = absolute temperature, (OC)
Z = Zener-Hollomon parameter.
Q = energy supplied by the thermal fluctuation to overcome obstacles such as dislocations.
The Z-values are uniquely related to the stress, and, hence the deformation of the material. For HCSS316 at
(900 – 1200)oC, (0 – 15) % reduction, and (0.07 – 1.5) s-1 strain rates, Q = 460kJ / mol (Aiyedun, 1984).
where;

III.

MEAN STRAIN RATE

The resistance to deformation of hot metal is both strain and strain rate dependent. For this reason it is
necessary to define the mean strain rate in the rolling pass.
According to Orowan and Pascal, mean strain rate is given as;


 

Vn
Rh1

1  3 r 
4
r
1 r 



…………………………(7)

where;
=
rolling velocity at the neutral position.
Vn
Ford and Alexander expressed it in the form:


 

Vn
Rh1

 4  3r 
r
2 
 2  r  

…………………..(8)

The form of mean strain rate estimation adopted by Sims, R. B. is given as:


 

Vn

 1 
ln 
r
1  r 


1

Rh1

……………………(9)

Integration of equation (9) into equation (6) above gives the basis of Zener – Hollomon Parameter computation
adopted by Sims. (Aiyedun, (1984)
According to Sellars, (1981) instantaneous strain rate in the roll gap is


  2v

h1  h 2 0.5
R 0 .5 h

www.ijesi.org

……………………(10)

61 | Page
A Study Of Zenner – Holomon Parameter Variation…
He further stated that the best mean strain rate will be one that gives a correct mean flow stress. Farag and
Sellars, (1973) thus obtained an approximate empirical equation of the form:

 2 0.25    h1  0.45
  1.08V   
 ln


R`0.5  0.5  h1h 2   h 2 




……………………………… (11)

where:

=
reduction
V
=
peripheral velocity of rolls (mms -1)
The above equation due to Farag and Sellars was adopted in the Reverse Sandwich Model for computation of
mean strain rate, which was then used in equation (6) to estimate the Zener - Hollomon Parameter (The quantity
used to model deformation).

IV. MODEL SIMULATION AND VALIDATION
The computer code developed using FORTRAN 77 for Zener - Hollomon Parameter computation at
different rolling reduction using the Reverse sandwich model is as provided. Fig. 2 shows the flow chart for the
simulation. The Program is user friendly and interactive, accepting input manually from the screen and
outputting results to user-defined file. Validation of the program was accomplished using data from hot rolling
experimental work carried out by authors on HCSS316 using 2 high reversing laboratory rolling mills.
For the material under study, experimental data abound in literatures for hot rolling based on Sims‟ theory of hot
flat rolling (Aiyedun, 1984; Shobowale, 1998; Alamu, 2001). The composition and thermo-mechanical history
of the specimen is presented in Table I, while the input data for the simulation is as shown in Table II.

V.

RESULTS AND DISCUSSION

The Output of the computer program, run with an IBM compatible Pentium (r) Processor, is presented
in Tables III - VI. The tables show the Zener – Hollomon Parameter values corresponding to different rolling
reduction characterized in different specimen. Also, the tables present the mean rolling temperature for each hot
rolling schedule to enable further validation of the program via a comparison between simulated and
experimental mean temperatures. This comparison is presented in Fig. 4. Similar data, from literatures, for hot
flat rolling of HCSS316 adopting Sims‟ theory is presented in Table VII. These sets of data, processed with
EXCEL package gave the polynomials shown in Fig. 3From the tables, variation of the Zener – Hollomon
Parameter with rolling reduction is evident. This is in agreement with earlier works of authors (Shobowale,
1998; Alamu and Taiwo, 2002). In other words, the rate of deformation in HCSS316 during hot rolling is a
function of the rolling reduction per pass. The possible relationship between these two parameters, as evident in
Fig. 3, takes the form of a non-linear polynomial, and is consistent in the two approaches; the Reverse sandwich
Model and Sims‟ theory.
From the two approaches investigated, the Zener – Hollomon Parameter as a function of rolling reduction takes

the form: ( Log 10Z   ar  br  cr  d ;...... a, b, c, d  cons tan ts ). For Sims‟ theory, a = -0.1833, b =
1.45, c = -2.8667, d = 21; while for Reverse Sandwich Model; a = 0.1367, b = -1.28, c = 3.9833, and, d =
16.82.
3

2

Fig. 4 reveals an agreement between simulated mean temperature and experimental values. Similar comparisons
have been used in other works (Shobowale, 1998; Alamu and Aiyedun, 2002, Ojediran and Alamu, 2002) to
confirm the validity of the output of the computer program. Hence, results obtained compares favourably with
experimental inferences as well as earlier works of researchers.

VI.

CONCLUSION

In the hot rolling of HCSS316 at low strain rates, (0.01 – 1.55) s-1 and low reductions,
( 10%), the Zener – Hollomon Parameter, (Z), has been found to be dependent on rolling reduction, (r), per

pass. For Sims‟ theory, Log 10Z   0.1833 r  1.45 r  2.8667 r  21 ; while using the Reverse
3

2

sandwich Model, Log 10Z   0.1367 r  1.28 r  3.9833 r  16 .82 for hot rolling computations.
3

2

www.ijesi.org

62 | Page
A Study Of Zenner – Holomon Parameter Variation…

[1]
[2]
[3]
[4]

[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]

REFERENCES
Afonja, A. A. and Sansome, D. H. (1973), “A Theoretical Analysis of the Sandwich Rolling Process”
Int. J. Mech. Sci., 15 (1): 1 – 14.
Aiyedun, P. O. (1984) “A Study of Loads and Torques for Light Reduction in Hot Flat Rolling” Ph. D.
Thesis, University of Sheffield.
Aiyedun, P. O. (1986), “Hot Flat Rolling Simulation by Use of the Bland and Ford‟s Cold Rolling
Theory for HCSS316 at Low Reduction and Low Strain Rates”, Proc, Int. AMSE Conf., 3 (1): 14 – 36.
Alamu, O. J. (2001) “Integration of the Reverse Sandwich Model into the Hot Rolling Bland and
Ford‟s Theory for Load and Torque Calculations”, M. Sc. Project Report, University of Ibadan, Ibadan,
Nigeria.
Alamu, O. J. and Aiyedun, P. O. (2003) “A Comparison of Temperature Gradient in Hot Rolling at
Low and High Strain Rates” JSET, 10 (1) (In Press)
Alamu, O. J. and Taiwo, A. “Computational Approach to a Study of Deformation in HCSS316 During
Hot Rolling, The Nigerian Academic Forum, (In Press)
Barbosa, R. A. N. M., (1983), Ph. D. Thesis, University of Sheffield.
Early, J.G. (1977) “Elevated Temperature Mechanical Behaviour of a Carbon-Manganese Pressure
Vessel Steel” Journal of Engineering Materials and Technology, pp. 359 – 365.
Farag, M. M. and Sellars, C. M., (1979) “Hot Working and Forming Process”, Paper presented at
Metals Society Conference, Sheffield.
Graham, W. O., Peter, R. K. and Partrick, J. D. (1993) Steel Designer‟s Manual, 5th ed. Blackwell
Scientific Publishers, London
Leduc, L. A., (1980), Ph. D. Thesis, University of Sheffield.
Lenard, J.G. (1980) “Roll Deformation in Cold Strip Rolling” Journal of Engineering Materials and
Technology, 102 (1):382 – 383.
Ojediran, J. O and Alamu, O. J (2002) “A study of Core Temperature Characteristics of Hot flat Rolled
HCSS 316” International Journal of Research in Science and Education 2(2)
Sellars, C. M. (1981) Paper presented at Colloque de Metallurgie, Institut National des Science et
Technique Nucleaires, Sanclay.
Shobowale, B. (1998) “The Reverse Sandwich Effect in HCSS316 Hot Flat Rolled at Low Strain Rates
and Low Reductions”, M. Sc. Project Report, University of Ibadan, Ibadan, Nigeria.
Sims, R.B. (1954) “The Calculation of Roll Force and Torque in Hot Rolling Mills” J.I.S.I. Pp. 191 –
200.
Usamah, S. and Lenard, J. G. (1980) “A Comparison of Cold Rolling Theories Based on the
Equilibrium Approach” Journal of Engineering Materials and Technology, 102 (1): 223 – 228.
Zener, C. and Hollomon, J.H., (1944), Journal of Applied Physics, 15, 22.

C------------------------------------------------------------------C Program : HOT ROLLING DEFORMATION BASED ON RSM MODEL
C___________________________________________________________________
IMPLICIT REAL*8(A-H,O-Z)
DIMENSION T(17),H(17),PLOT(17)
CHARACTER RSM*20, SPNO*6,CONTD
DATA IN/'N'/,IY/'Y'/
Q=460000.0
GKR=8.314
P=132.0
C=0.02474
RO=139.70
AZEN = 0.0
C

FILES CREATION AND INTERACTIVE DATA ENTRY
WRITE(*,*)'Enter a Filename for the Result.'
READ(*,25)RSM
OPEN(UNIT=7,FILE=RSM,STATUS='NEW')

10 WRITE(*,*)'Supply the Specimen Identification Number.'
READ(*,12)SPNO

www.ijesi.org

63 | Page
A Study Of Zenner – Holomon Parameter Variation…
WRITE(*,*)'Enter the Rolling Speed,(mm/s).'
READ(*,*)V
WRITE(*,*)'Supply the Furnace Temperature (Deg.Celcius).'
READ(*,*)TF
WRITE(*,*)'Supply the Initial Specimen Height,(mm).'
READ(*,*)HO
WRITE(*,*)'Enter the Final Specimen Height,(mm).'
READ(*,*)HF
WRITE(*,*) 'Enter the Width of the Specimen,(mm).'
READ(*,*) W
WRITE(7,*)
WRITE(7,100)SPNO
100 FORMAT(1X,'OUTPUT FOR SPECIMEN 'A4)
WRITE(7,*)'------------------------------------------'
12 FORMAT(A4)
20 FORMAT(A1)
25 FORMAT(A4)
C RELATIONSHIP BETWEEN ROLLING SPEED(V) AND THE REVERSE SANDWICH
C ROLLING MODEL CONSTANT(K)
IF(V.LE.10.0) THEN
AK=1.59
ELSE IF(V.LE.45.0) THEN
AK=1.40
ELSE IF(V.LE.100.0) THEN
AK=1.19
ELSE IF(V.LE.180.0) THEN
AK=1.16
ELSE IF(V.LE.250.0) THEN
AK=1.12
ELSE
WRITE(7,*) "AK IS UNDEFINED"
STOP
END IF
C CALCULATION OF REDUCTION(DEL), PERCENTAGE REDUCTION(DELPER) AND
C DEFORMED ROLL RADIUS(DR)
DEL = HO-HF
DELPER=((HO-HF)/HO)*100
DR = RO*(1+(C*P)/(DEL*W))
C
C
C

COMPUTATION OF MEAN TEMPERATURE(TMEAN),SURFACE TEMPERATURE(TE),
TEMPERATURE DISTRIBUTION(TDIST), MIDDLE TEMPERATURE(TMID) AND
TEMPERATURE VARIATION ALONG THICKNESS (T1.....T17)

TMEAN = (TF+(TF/AK))/2.0
TMID = (TMEAN+TF)/2.0
TE = TF/AK
TDIST = TMID-TE
T(1) =TE
DO 7 J=1,4
7 T(J+1) = T(J)+0.2*TDIST
DO 8 J=5,7
8 T(J+1) = T(J) +0.04*TDIST
T(9) = (TMEAN+TF)/2.0
M=0
DO 9 J=8,5,-1

www.ijesi.org

64 | Page
A Study Of Zenner – Holomon Parameter Variation…
M=M+1
9 T(J*2)=T(M*2)
M1=3
DO 11 J=15,11,-2
T(J)=T(M1)
11 M1=M1+2
T(17)=T(1)
C COMPUTATION OF STRAIN RATE
SRT = ((1.08*V)/(DR*DEL)**0.5)*((DEL/(HO*HF))**0.25)*(ALOG(HO/HF)
1)**0.45
C
C

ESTIMATION OF THICKNESS VARIATION CORRESPONDING TO TEMPERATURE
VARIATION (H1..............H17) ALONG HEIGHT

H(1) = 0
H(2) = HO/17.0
DO 13 J=2,16
IF(J.EQ.8) THEN
H(J+1) = HO/2.0
ELSE IF (J.EQ.16) THEN
H(J+1) = HO
ELSE
H(J+1) = H(J)+1
END IF
13 CONTINUE
C ESTIMATION OF ZENER HOLLOMON PARAMETER ALONG THICKNESS
C (Z1.........Z17)
DO 15 J = 1,17
PLOT(J) = ALOG10(SRT*DEXP(Q/(GKR*(T(J)+273))))
15 CONTINUE

DO 35 J = 1,17
35 AZEN = AZEN+PLOT(J)
CONTINUE
AZEN = AZEN/17.0
26 FORMAT(1X,'SPECIMEN NO.
= 'A4)
27 FORMAT(1X,'MEAN TEMPERATURE,('C)
= 'F7.2)
37 FORMAT(1X,'ZENER-HOLLOMON PARAMETER(LOG) = 'F5.2)
40 FORMAT(1X,'ROLLING REDUCTION,(%)
= 'F5.2)
WRITE(7,26)SPNO
WRITE(7,27)TMEAN
WRITE(7,40)DELPER
WRITE(7,37)AZEN
WRITE(7,*)'_____________________________________________'
WRITE(*,29)RSM
29 FORMAT(1X,13HEnter, edit ,A14,14Hfor the output)
30 WRITE(*,*)'DO YOU WISH TO CONTINUE?(Y/N)'
READ(*,20)CONTD
IF(CONTD.EQ.IY) GO TO 10
IF(CONTD.EQ.IN) GO TO 31
WRITE(*,*)'INVALID RESPONSE !! ENTER (Y/N) USING UPPERCASE LETTER'
GO TO 30
31 STOP
END

www.ijesi.org

65 | Page
A Study Of Zenner – Holomon Parameter Variation…
Table I: Chemical Compositions and Thermo-mechanical Data for HCSS316
Element in
HCSS316
C
S
Mo
Ni
Si
Cr
W
Mn
Nb
V
Ti
Co
Cu
N
O

Percentage
Composition (%wt)
0.054
0.016
2.050
11.300
0.540
17.400
<0.020
1.370
0.100
0.070
0.040
0.140
0.320
524ppm
122ppm

Preliminary
Measurement
Mean Grain Size,
(m)
Aspect Ratio
Micro hardness HV
(kg/mm2)
Temperature,
(OC)
0.2% P. S.,
(N/mm2)
Ultimate Tensile Strength,
(N/mm2)
Elongation,
(%)
Reduction in Area,
(%)

Value
39.30
1.02
165.00
20.00
246.00
595.00
67.00
66.00

TABLE II: The Reverse Sandwich Rolling Experimental Data*.
S/N SPEC. FURN. THICKNESS WIDTH ROLLING
NO. TEMP. INIT. FINL.
SPEED
(OC) (mm) (mm) (mm) (mm/s)
1
2
3
4

H50
H51
H52
H53

1120 14.17 12.73 75.17
1128 12.03 10.82 75.20
1123 10.04 09.09 75.20
1122 08.03 07.40 75.23
*(Aiyedun,1984)

009.32
009.32
009.32
009.32

TABLE III:
OUTPUT FOR SPECIMEN H50
-------------------------------------SPECIMEN NO.
= H50
MEAN TEMPERATURE,('C)
= 912.20
ROLLING REDUCTION,(%)
= 10.16
ZENER-HOLLOMON PARAMETER(LOG) = 19.66
______________________________________
TABLE IV:
OUTPUT FOR SPECIMEN H51
-------------------------------------SPECIMEN NO.
= H51
MEAN TEMPERATURE,('C)
= 918.72
ROLLING REDUCTION,(%)
= 10.06
ZENER-HOLLOMON PARAMETER(LOG) = 20.76
______________________________________
TABLE V:
OUTPUT FOR SPECIMEN H52
-------------------------------------SPECIMEN NO.
= H52
MEAN TEMPERATURE,('C)
= 914.64
ROLLING REDUCTION,(%)
= 9.46
ZENER-HOLLOMON PARAMETER(LOG) = 20.94
______________________________________

www.ijesi.org

66 | Page
A Study Of Zenner – Holomon Parameter Variation…
TABLE VI:
OUTPUT FOR SPECIMEN H53
-------------------------------------SPECIMEN NO.
= H53
MEAN TEMPERATURE,('C)
= 913.83
ROLLING REDUCTION,(%)
= 7.85
ZENER-HOLLOMON PARAMETER(LOG) = 21.02
______________________________________
Table VII: *Values Obtained for the Specimens
Using Sims‟ Theory.
S /N

1
2
3
4

Specimen
Identification
Number
H50
H51
H52
H53

Rolling
Reduction
(%)
10.16
10.06
9.46
7.85

Log10(Z)

19.40
19.60
20.50
21.00

*Shobowale,(1998)

Frictional
force

Normal
force

Hard
Matrix

HO

Soft Clad

Hard
Matrix

Hf

Roll

FIG. 1 Schematic Illustration of Reverse Sandwich Rolling Process.

www.ijesi.org

67 | Page
A Study Of Zenner – Holomon Parameter Variation…

START

READ:

SP.NO, V, Tf, H0, W, Hf

NO
NO

NO

NO

NO

IS
V< 250?

IS
V< 180?

IS
V< 100?

IS
V< 45?

YES

YES

K = 1.59

K = 1.40
COMPUTE

YES

YES

YES

IS
V< 10?

K = 1.19

RED
= HO - HF
% RED = ((HO - HF) /HO))*100
DR
= RO*(1+(C*P)/(RED*W))
Tm
= (Tf+(Tf / K))/2
TCORE = (TM+ TF)/2
TS
= Tf / K
TDIST = TCORE - TS
0.25 
  h1  0.45
1.08V   2 
 ln
  0.5 0.5 


R`   h1h 2   h 2 




K = 1.16


 Q 
LogZ  Log   exp



 RT  


K = 1.12

COUNTER J = 0
K = UNDEFINED
COMPUTE J, T(J), H(J), LogZ
NO

YES
IS J = 17 ?

J =J+1
NO

NO

ALL SPECIMEN
CONSIDERED?

WRITE SP NO,Tm,
,%RED, LogZMEAN

YES

STOP

Fig. 2: Flow Chart for the RSM Simulation

www.ijesi.org

68 | Page
A Study Of Zenner – Holomon Parameter Variation…
21.5

Zener - Hollomon Parameter

21

3

2

y = 0.1367x - 1.28x + 3.9833x + 16.82
R2 = 1

20.5
y = -0.1833x3 + 1.45x2 - 2.8667x + 21
R2 = 1
20

19.5
RSM

19
10.16

SIMS

Poly. (RSM)

Poly. (SIMS)

10.06

9.46

7.85

Rolling Reduction, (%)

FIG.3: DEPENDENCE OF ZENER - HOLLOMON PARAMETER ON ROLLING REDUCTION BASED ON
DIFFERENT ROLLING THEORIES

930

925

O

Temperature, ( C)

920

915

910

MEAN; EXPERIMENTAL

MEAN; SIMULATED

905

900
H50

H51

H52

H53

High Carbon Stainless Steel 316 Specimen.

Fig. 4: VALIDATION OF SIMULATED RESULTS USING MEAN ROLLING TEMPERATURE ESTIMATION

www.ijesi.org

69 | Page

Contenu connexe

Tendances

Structural Integrity Analysis: Chapter 2 Fracture Mechanics
Structural Integrity Analysis: Chapter  2 Fracture MechanicsStructural Integrity Analysis: Chapter  2 Fracture Mechanics
Structural Integrity Analysis: Chapter 2 Fracture MechanicsIgor Kokcharov
 
A refined energy-based model for friction stir processing of Al- Zn-Mg alloy
A refined energy-based model for friction stir processing of Al- Zn-Mg alloyA refined energy-based model for friction stir processing of Al- Zn-Mg alloy
A refined energy-based model for friction stir processing of Al- Zn-Mg alloyIJERA Editor
 
formability limit diagram
formability limit diagramformability limit diagram
formability limit diagramPravinkumar
 
FEA based Dissipation Energy and Temperature Distribution of Rubber Bushing
FEA based Dissipation Energy and Temperature Distribution of Rubber BushingFEA based Dissipation Energy and Temperature Distribution of Rubber Bushing
FEA based Dissipation Energy and Temperature Distribution of Rubber BushingIJERA Editor
 
Materials lec 4
Materials lec 4Materials lec 4
Materials lec 4Iqra Tariq
 
Computational buckling of a three lobed crosection cylindrical shell with var...
Computational buckling of a three lobed crosection cylindrical shell with var...Computational buckling of a three lobed crosection cylindrical shell with var...
Computational buckling of a three lobed crosection cylindrical shell with var...prjpublications
 
TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING
TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING
TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING IAEME Publication
 
Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...
Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...
Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...IJMER
 
Case Study on Failure Due to Fatigue
Case Study on Failure Due to FatigueCase Study on Failure Due to Fatigue
Case Study on Failure Due to FatigueAbhijit Debnath
 
Numerical analysis on residual stress on plate girder
Numerical analysis on residual stress on plate girderNumerical analysis on residual stress on plate girder
Numerical analysis on residual stress on plate girderTEJASKRIYA PRADHAN
 
Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...
Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...
Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...iosrjce
 
Mi 291 chapter 4 (learning from failure)
Mi 291 chapter 4 (learning from failure)Mi 291 chapter 4 (learning from failure)
Mi 291 chapter 4 (learning from failure)varun teja G.V.V
 
01 fundamentals of metalworking
01 fundamentals of metalworking01 fundamentals of metalworking
01 fundamentals of metalworkingajit_singh206
 
Friction stir welding of aluminium 5086 alloys
Friction stir welding of aluminium 5086 alloysFriction stir welding of aluminium 5086 alloys
Friction stir welding of aluminium 5086 alloyseSAT Journals
 
Investigation of Effect of Process Parameters on Maximum Temperature during F...
Investigation of Effect of Process Parameters on Maximum Temperature during F...Investigation of Effect of Process Parameters on Maximum Temperature during F...
Investigation of Effect of Process Parameters on Maximum Temperature during F...IJSRD
 

Tendances (19)

Structural Integrity Analysis: Chapter 2 Fracture Mechanics
Structural Integrity Analysis: Chapter  2 Fracture MechanicsStructural Integrity Analysis: Chapter  2 Fracture Mechanics
Structural Integrity Analysis: Chapter 2 Fracture Mechanics
 
A refined energy-based model for friction stir processing of Al- Zn-Mg alloy
A refined energy-based model for friction stir processing of Al- Zn-Mg alloyA refined energy-based model for friction stir processing of Al- Zn-Mg alloy
A refined energy-based model for friction stir processing of Al- Zn-Mg alloy
 
formability limit diagram
formability limit diagramformability limit diagram
formability limit diagram
 
FEA based Dissipation Energy and Temperature Distribution of Rubber Bushing
FEA based Dissipation Energy and Temperature Distribution of Rubber BushingFEA based Dissipation Energy and Temperature Distribution of Rubber Bushing
FEA based Dissipation Energy and Temperature Distribution of Rubber Bushing
 
Materials lec 4
Materials lec 4Materials lec 4
Materials lec 4
 
Computational buckling of a three lobed crosection cylindrical shell with var...
Computational buckling of a three lobed crosection cylindrical shell with var...Computational buckling of a three lobed crosection cylindrical shell with var...
Computational buckling of a three lobed crosection cylindrical shell with var...
 
Fatigue Mechanics of Materials
Fatigue Mechanics of MaterialsFatigue Mechanics of Materials
Fatigue Mechanics of Materials
 
TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING
TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING
TENSILE BEHAVIOUR OF ALUMINIUM PLATES (5083) WELDED BY FRICTION STIR WELDING
 
Engg mat
Engg mat Engg mat
Engg mat
 
Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...
Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...
Buckling Analysis of Cold Formed Steel Compression Members at Elevated Temper...
 
D04102016020
D04102016020D04102016020
D04102016020
 
Case Study on Failure Due to Fatigue
Case Study on Failure Due to FatigueCase Study on Failure Due to Fatigue
Case Study on Failure Due to Fatigue
 
Numerical analysis on residual stress on plate girder
Numerical analysis on residual stress on plate girderNumerical analysis on residual stress on plate girder
Numerical analysis on residual stress on plate girder
 
Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...
Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...
Experimental Investigation of Friction Stir Welding Of Aluminum Aa6061 Alloy ...
 
Friction stir welding
Friction stir weldingFriction stir welding
Friction stir welding
 
Mi 291 chapter 4 (learning from failure)
Mi 291 chapter 4 (learning from failure)Mi 291 chapter 4 (learning from failure)
Mi 291 chapter 4 (learning from failure)
 
01 fundamentals of metalworking
01 fundamentals of metalworking01 fundamentals of metalworking
01 fundamentals of metalworking
 
Friction stir welding of aluminium 5086 alloys
Friction stir welding of aluminium 5086 alloysFriction stir welding of aluminium 5086 alloys
Friction stir welding of aluminium 5086 alloys
 
Investigation of Effect of Process Parameters on Maximum Temperature during F...
Investigation of Effect of Process Parameters on Maximum Temperature during F...Investigation of Effect of Process Parameters on Maximum Temperature during F...
Investigation of Effect of Process Parameters on Maximum Temperature during F...
 

En vedette

8 марта
8 марта8 марта
8 мартаElena-Sh
 
DRIVE BY ACTING EXERCISE.
DRIVE BY ACTING EXERCISE.DRIVE BY ACTING EXERCISE.
DRIVE BY ACTING EXERCISE.runicfalcon
 
Field Guide to transforming HR through video
Field Guide to transforming HR through videoField Guide to transforming HR through video
Field Guide to transforming HR through videoCorporate Television
 
Lessons of oil by howard marks
Lessons of oil by howard marksLessons of oil by howard marks
Lessons of oil by howard marksFrank Ragol
 
Паспорт проблемы
Паспорт проблемыПаспорт проблемы
Паспорт проблемыWikiHelpTV
 

En vedette (6)

8 марта
8 марта8 марта
8 марта
 
DRIVE BY ACTING EXERCISE.
DRIVE BY ACTING EXERCISE.DRIVE BY ACTING EXERCISE.
DRIVE BY ACTING EXERCISE.
 
Field Guide to transforming HR through video
Field Guide to transforming HR through videoField Guide to transforming HR through video
Field Guide to transforming HR through video
 
USDA Home Loan Application buyer package
USDA Home Loan Application buyer packageUSDA Home Loan Application buyer package
USDA Home Loan Application buyer package
 
Lessons of oil by howard marks
Lessons of oil by howard marksLessons of oil by howard marks
Lessons of oil by howard marks
 
Паспорт проблемы
Паспорт проблемыПаспорт проблемы
Паспорт проблемы
 

Similaire à I021201059069

detalied analysis of warm rolled steels.docx
detalied analysis of warm rolled steels.docxdetalied analysis of warm rolled steels.docx
detalied analysis of warm rolled steels.docxsudhakargeruganti
 
INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...
INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...
INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...Journal For Research
 
A refined energy-based model for friction stir processing of AlZn-Mg alloy
A refined energy-based model for friction stir processing of AlZn-Mg alloy A refined energy-based model for friction stir processing of AlZn-Mg alloy
A refined energy-based model for friction stir processing of AlZn-Mg alloy IJERA Editor
 
IJCER (www.ijceronline.com) International Journal of computational Engineerin...
IJCER (www.ijceronline.com) International Journal of computational Engineerin...IJCER (www.ijceronline.com) International Journal of computational Engineerin...
IJCER (www.ijceronline.com) International Journal of computational Engineerin...ijceronline
 
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...ijeljournal
 
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...ijeljournal
 
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...ijeljournal
 
12-2-Publication-Experimental Analysis of Explosive Forming
12-2-Publication-Experimental Analysis of Explosive Forming12-2-Publication-Experimental Analysis of Explosive Forming
12-2-Publication-Experimental Analysis of Explosive FormingSaeed Jabalamelian
 
Design &Analysis of Pure Iron Casting with Different Moulds
Design &Analysis of Pure Iron Casting with Different MouldsDesign &Analysis of Pure Iron Casting with Different Moulds
Design &Analysis of Pure Iron Casting with Different MouldsIJMER
 
3 dimensional nonlinear finite element analysis of both thermal and mechanica...
3 dimensional nonlinear finite element analysis of both thermal and mechanica...3 dimensional nonlinear finite element analysis of both thermal and mechanica...
3 dimensional nonlinear finite element analysis of both thermal and mechanica...Alexander Decker
 
Natural convection heat transfer from two parallel horizontal cylinders embed...
Natural convection heat transfer from two parallel horizontal cylinders embed...Natural convection heat transfer from two parallel horizontal cylinders embed...
Natural convection heat transfer from two parallel horizontal cylinders embed...Ahmed Al-Sammarraie
 
Natural convection heat transfer inside inclined open cylinder
Natural convection heat transfer inside inclined open cylinderNatural convection heat transfer inside inclined open cylinder
Natural convection heat transfer inside inclined open cylinderIAEME Publication
 
Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...
Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...
Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...Ijripublishers Ijri
 
Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...
Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...
Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...IOSR Journals
 
Computational buckling of a three lobed crosection
Computational buckling of a three lobed crosectionComputational buckling of a three lobed crosection
Computational buckling of a three lobed crosectionprj_publication
 
Journal Publication - Elsevier
Journal Publication - ElsevierJournal Publication - Elsevier
Journal Publication - Elsevierpreetish09
 
Paper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Paper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxPaper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Paper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxaljabbery
 

Similaire à I021201059069 (20)

Im2515171522
Im2515171522Im2515171522
Im2515171522
 
detalied analysis of warm rolled steels.docx
detalied analysis of warm rolled steels.docxdetalied analysis of warm rolled steels.docx
detalied analysis of warm rolled steels.docx
 
INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...
INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...
INVESTIGATION OF RESIDUAL STRESSES IN WELDING AND ITS EFFECT ON MECHANICAL BE...
 
A refined energy-based model for friction stir processing of AlZn-Mg alloy
A refined energy-based model for friction stir processing of AlZn-Mg alloy A refined energy-based model for friction stir processing of AlZn-Mg alloy
A refined energy-based model for friction stir processing of AlZn-Mg alloy
 
IJCER (www.ijceronline.com) International Journal of computational Engineerin...
IJCER (www.ijceronline.com) International Journal of computational Engineerin...IJCER (www.ijceronline.com) International Journal of computational Engineerin...
IJCER (www.ijceronline.com) International Journal of computational Engineerin...
 
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
 
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
 
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
Anisotropy of Coercive Force of Single Crystals and Sheets of Silicon Iron wi...
 
12-2-Publication-Experimental Analysis of Explosive Forming
12-2-Publication-Experimental Analysis of Explosive Forming12-2-Publication-Experimental Analysis of Explosive Forming
12-2-Publication-Experimental Analysis of Explosive Forming
 
Design &Analysis of Pure Iron Casting with Different Moulds
Design &Analysis of Pure Iron Casting with Different MouldsDesign &Analysis of Pure Iron Casting with Different Moulds
Design &Analysis of Pure Iron Casting with Different Moulds
 
30120130406018 2-3
30120130406018 2-330120130406018 2-3
30120130406018 2-3
 
3 dimensional nonlinear finite element analysis of both thermal and mechanica...
3 dimensional nonlinear finite element analysis of both thermal and mechanica...3 dimensional nonlinear finite element analysis of both thermal and mechanica...
3 dimensional nonlinear finite element analysis of both thermal and mechanica...
 
Natural convection heat transfer from two parallel horizontal cylinders embed...
Natural convection heat transfer from two parallel horizontal cylinders embed...Natural convection heat transfer from two parallel horizontal cylinders embed...
Natural convection heat transfer from two parallel horizontal cylinders embed...
 
Natural convection heat transfer inside inclined open cylinder
Natural convection heat transfer inside inclined open cylinderNatural convection heat transfer inside inclined open cylinder
Natural convection heat transfer inside inclined open cylinder
 
Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...
Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...
Experimental Investigation on Heat Transfer By Natural Convection Over A Cyli...
 
Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...
Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...
Experimental Investigation and Analysis of Extrusion of Lead from Round Secti...
 
L1303059097
L1303059097L1303059097
L1303059097
 
Computational buckling of a three lobed crosection
Computational buckling of a three lobed crosectionComputational buckling of a three lobed crosection
Computational buckling of a three lobed crosection
 
Journal Publication - Elsevier
Journal Publication - ElsevierJournal Publication - Elsevier
Journal Publication - Elsevier
 
Paper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Paper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxPaper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Paper88933-938.pdfxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
 

Dernier

HELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptx
HELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptxHELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptx
HELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptxHelene Heckrotte
 
Developing Coaching Skills: Mine, Yours, Ours
Developing Coaching Skills: Mine, Yours, OursDeveloping Coaching Skills: Mine, Yours, Ours
Developing Coaching Skills: Mine, Yours, OursKaiNexus
 
To Create Your Own Wig Online To Create Your Own Wig Online
To Create Your Own Wig Online  To Create Your Own Wig OnlineTo Create Your Own Wig Online  To Create Your Own Wig Online
To Create Your Own Wig Online To Create Your Own Wig Onlinelng ths
 
Data skills for Agile Teams- Killing story points
Data skills for Agile Teams- Killing story pointsData skills for Agile Teams- Killing story points
Data skills for Agile Teams- Killing story pointsyasinnathani
 
ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...
ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...
ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...ISONIKELtd
 
Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)
Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)
Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)tazeenaila12
 
AMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdf
AMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdfAMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdf
AMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdfJohnCarloValencia4
 
Graham and Doddsville - Issue 1 - Winter 2006 (1).pdf
Graham and Doddsville - Issue 1 - Winter 2006 (1).pdfGraham and Doddsville - Issue 1 - Winter 2006 (1).pdf
Graham and Doddsville - Issue 1 - Winter 2006 (1).pdfAnhNguyen97152
 
IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...
IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...
IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...AustraliaChapterIIBA
 
Trauma Training Service for First Responders
Trauma Training Service for First RespondersTrauma Training Service for First Responders
Trauma Training Service for First RespondersBPOQe
 
Plano de marketing- inglês em formato ppt
Plano de marketing- inglês  em formato pptPlano de marketing- inglês  em formato ppt
Plano de marketing- inglês em formato pptElizangelaSoaresdaCo
 
NewBase 25 March 2024 Energy News issue - 1710 by Khaled Al Awadi_compress...
NewBase  25 March  2024  Energy News issue - 1710 by Khaled Al Awadi_compress...NewBase  25 March  2024  Energy News issue - 1710 by Khaled Al Awadi_compress...
NewBase 25 March 2024 Energy News issue - 1710 by Khaled Al Awadi_compress...Khaled Al Awadi
 
PDT 88 - 4 million seed - Seed - Protecto.pdf
PDT 88 - 4 million seed - Seed - Protecto.pdfPDT 88 - 4 million seed - Seed - Protecto.pdf
PDT 88 - 4 million seed - Seed - Protecto.pdfHajeJanKamps
 
The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...
The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...
The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...Brian Solis
 
Amazon ppt.pptx Amazon about the company
Amazon ppt.pptx Amazon about the companyAmazon ppt.pptx Amazon about the company
Amazon ppt.pptx Amazon about the companyfashionfound007
 
Anyhr.io | Presentation HR&Recruiting agency
Anyhr.io | Presentation HR&Recruiting agencyAnyhr.io | Presentation HR&Recruiting agency
Anyhr.io | Presentation HR&Recruiting agencyHanna Klim
 
Scrum Events & How to run them effectively
Scrum Events & How to run them effectivelyScrum Events & How to run them effectively
Scrum Events & How to run them effectivelyMarianna Nakou
 
Upgrade Your Banking Experience with Advanced Core Banking Applications
Upgrade Your Banking Experience with Advanced Core Banking ApplicationsUpgrade Your Banking Experience with Advanced Core Banking Applications
Upgrade Your Banking Experience with Advanced Core Banking ApplicationsIntellect Design Arena Ltd
 
Personal Brand Exploration Presentation Eric Bonilla
Personal Brand Exploration Presentation Eric BonillaPersonal Brand Exploration Presentation Eric Bonilla
Personal Brand Exploration Presentation Eric BonillaEricBonilla13
 

Dernier (20)

HELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptx
HELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptxHELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptx
HELENE HECKROTTE'S PROFESSIONAL PORTFOLIO.pptx
 
Developing Coaching Skills: Mine, Yours, Ours
Developing Coaching Skills: Mine, Yours, OursDeveloping Coaching Skills: Mine, Yours, Ours
Developing Coaching Skills: Mine, Yours, Ours
 
To Create Your Own Wig Online To Create Your Own Wig Online
To Create Your Own Wig Online  To Create Your Own Wig OnlineTo Create Your Own Wig Online  To Create Your Own Wig Online
To Create Your Own Wig Online To Create Your Own Wig Online
 
Data skills for Agile Teams- Killing story points
Data skills for Agile Teams- Killing story pointsData skills for Agile Teams- Killing story points
Data skills for Agile Teams- Killing story points
 
ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...
ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...
ISONIKE Ltd Accreditation for the Conformity Assessment and Certification of ...
 
WAM Corporate Presentation Mar 25 2024.pdf
WAM Corporate Presentation Mar 25 2024.pdfWAM Corporate Presentation Mar 25 2024.pdf
WAM Corporate Presentation Mar 25 2024.pdf
 
Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)
Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)
Harvard Business Review.pptx | Navigating Labor Unrest (March-April 2024)
 
AMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdf
AMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdfAMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdf
AMAZON SELLER VIRTUAL ASSISTANT PRODUCT RESEARCH .pdf
 
Graham and Doddsville - Issue 1 - Winter 2006 (1).pdf
Graham and Doddsville - Issue 1 - Winter 2006 (1).pdfGraham and Doddsville - Issue 1 - Winter 2006 (1).pdf
Graham and Doddsville - Issue 1 - Winter 2006 (1).pdf
 
IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...
IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...
IIBA® Melbourne - Navigating Business Analysis - Excellence for Career Growth...
 
Trauma Training Service for First Responders
Trauma Training Service for First RespondersTrauma Training Service for First Responders
Trauma Training Service for First Responders
 
Plano de marketing- inglês em formato ppt
Plano de marketing- inglês  em formato pptPlano de marketing- inglês  em formato ppt
Plano de marketing- inglês em formato ppt
 
NewBase 25 March 2024 Energy News issue - 1710 by Khaled Al Awadi_compress...
NewBase  25 March  2024  Energy News issue - 1710 by Khaled Al Awadi_compress...NewBase  25 March  2024  Energy News issue - 1710 by Khaled Al Awadi_compress...
NewBase 25 March 2024 Energy News issue - 1710 by Khaled Al Awadi_compress...
 
PDT 88 - 4 million seed - Seed - Protecto.pdf
PDT 88 - 4 million seed - Seed - Protecto.pdfPDT 88 - 4 million seed - Seed - Protecto.pdf
PDT 88 - 4 million seed - Seed - Protecto.pdf
 
The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...
The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...
The End of Business as Usual: Rewire the Way You Work to Succeed in the Consu...
 
Amazon ppt.pptx Amazon about the company
Amazon ppt.pptx Amazon about the companyAmazon ppt.pptx Amazon about the company
Amazon ppt.pptx Amazon about the company
 
Anyhr.io | Presentation HR&Recruiting agency
Anyhr.io | Presentation HR&Recruiting agencyAnyhr.io | Presentation HR&Recruiting agency
Anyhr.io | Presentation HR&Recruiting agency
 
Scrum Events & How to run them effectively
Scrum Events & How to run them effectivelyScrum Events & How to run them effectively
Scrum Events & How to run them effectively
 
Upgrade Your Banking Experience with Advanced Core Banking Applications
Upgrade Your Banking Experience with Advanced Core Banking ApplicationsUpgrade Your Banking Experience with Advanced Core Banking Applications
Upgrade Your Banking Experience with Advanced Core Banking Applications
 
Personal Brand Exploration Presentation Eric Bonilla
Personal Brand Exploration Presentation Eric BonillaPersonal Brand Exploration Presentation Eric Bonilla
Personal Brand Exploration Presentation Eric Bonilla
 

I021201059069

  • 1. International Journal of Engineering Science Invention ISSN (Online): 2319 – 6734, ISSN (Print): 2319 – 6726 www.ijesi.org Volume 2 Issue 12ǁ December 2013 ǁ PP.59-69 A Study of Zenner – Holomon Parameter Variation with Pass Reduction in Steel Rolling 1, Okediran, I.K., 2,Alamu, O.J. and 3,Durowoju, M.O. Department of Mechanical Engineering, Osun State University, Osogbo, Nigeria. ABRSTRACT : An attempt is made in this work to establish mathematical relationships between the Zener – Hollomon Parameter and rolling reduction per pass in the hot rolling of Type 316 High Carbon Stainless Steel (HCSS316). The hot rolling simulation of steel based on the Reverse Sandwich Model and that based on the Sims‟ theory were used with the hot rolling experimental data for HCSS316, to generate results which reveal the dependency of the two rolling parameters on each other. These results were then processed with the EXCEL Package to arrive at a quantitative description of the observed relationship. The Zener–Hollomon parameter (Z) was found to be a non linear function of rolling reduction (r): ( Log 10Z   ar  br  cr  d ;...... a, b, c, d  cons tan ts ) for High Carbon Stainless Steel hot flat rolled at low strain rates. The results compare favourably with experimental inferences. 3 2 KEY WORD: Zener-Hollomon Parameter, rolling reduction, simulation] I. INTRODUCTION Rolling nowadays accounts for about 90% of all metals produced by metal working processes. It was first developed in the late 1500s. Traditionally, the initial material form for rolling was an ingot. By far the largest amount of finished steel production is achieved by rolling. The Semi-finished products cast from the steelmaking furnace are reheated to the austenising range and passed through a series of mills with rolls of the required profile to force the hot steel into the finished shape. (Graham, 1993) Developed in the mid – 1800s two high and three high rolling mills are still used today for initial breakdown passes on cast ingots. However, this practice is now being rapidly replaced by continuous casting and rolling, with much higher efficiency and lower cost.The advent of continuous casters has necessitated hot flat rolling at low strain rates (0.01 – 1.55) s-1 and low reduction ( 10%) (Aiyedun, 1986). Under such rolling condition, the contact time in the roll gap increases and heat loss from the pre-heated ingot to the surroundings and the rolls increases. This variation in temperature induces a non-uniform deformation pattern in the through-thickness of the rolled steel. The deformation, by virtue of the un-even re-crystallization and grain refinement, as a result creates in the material a low-temperature harder surface and a high-temperature softer core (Alamu and Aiyedun, 2003, Ojediran and Alamu, 2003).(see Fig.1)The prevailing situation has been investigated by authors. Barbosa, (1983), Leduc, (1983), and Aiyedun (1984) referred to the observed effect as “Reverse Sandwich” or Roll chilling, as the through-thickness hardness variation presents a direct opposite of what obtains in a sandwich rolling process, where harder metals are sandwiched between layers of softer metals to effect rolling of very hard and high strength metals into thin strips without rupture in the rolls (Afonja and Sansome, 1973). Studies abound in literatures on deformation in sandwich rolling and the reverse sandwich effect or roll chilling. The adoption of computer simulation in modeling engineering systems further expands this area of study. The Zener-Hollomon parameter is uniquely related to stresses, and gives an indication of deformation in a material. Researchers (Zener and Hollomon, 1944; Aiyedun, 1984) have long established that deformation increases with decreasing Zener – Hollomon parameter value. Alamu and Taiwo, (2002) employed computer simulation to study deformation pattern in the hot rolling of High Carbon Stainless Steel type 316 (HCSSS316) using a reverse Sandwich Model developed by Shobowale (1998). In the work, the reverse sandwich model was simulated incorporating strain rate and Zener-Hollomon parameter computation for different zones along the thickness of HCSS316 during hot flat rolling, thus permitting a study of the deformation pattern of this material during hot rolling.In this work, the relationship between deformation rate, in terms of the Zener-Hollomon parameter and rolling reduction per pass in the hot rolling of HCSS316 is investigated, using the reverse sandwich model and Sims‟ theory of hot flat rolling, with hot flat rolling experimental data earlier obtained by researchers for HCSS316. www.ijesi.org 59 | Page
  • 2. A Study Of Zenner – Holomon Parameter Variation… II. MATERIALS AND METHOD Deformation in hot rolling is temperature dependent. In this process the strength of a metal decreases as temperature rises, and its grains can be distorted more easily. In line with Sims‟ theory, hot rolling process is characterized by “sticking throughout the roll gap” (Sims, 1954). However, this is not entirely true for hot rolling of HCSS316 at low strain rates; here, the rolling surfaces are sufficiently chilled leading to a mixed sliding –sticking condition in the roll gap (Aiyedun, 1986). THEORIES OF METAL ROLLING Lennard (1980), and Usamah and Lennard (1980), amongst other literatures have reported that, Orowan‟s theory is the most comprehensive among the many theories of rolling. According to Lennard, (1980), the approach requires mathematical descriptions of material behaviour and deformation as well as assumptions of frictional conditions at the roll – metal interface and mode of roll deformation. The complexity of the method of solution of Orowan‟s equation caused later researchers, notably, Sims, Bland and Ford, Alexander, Alexander and Ford and Atreya and Lennard to develop solutions based on simplifying assumptions. 1. Orowan’s Theory: According to Lennard, (1980) Orowan‟s theory can be summarized in the differential equation: d hs  2k   tan    2 R`s.sin    cos  d where:  …………….. (1) interfacial shear stress, roll pressure, thickness of the strip in the roll gap, yield strength in shear of the material, current radius of curvature of the roll at a particular location, independent variable (angle) measured from the centre line in the roll gap. The instantaneous yield stress, k, depends on rolling temperature, strain and strain rate, and must be determined s h k R`  = = = = = = before evaluating the mean yield stress, K , for subsequent computation of rolling parameters of interest such as load and torque. 2. Sims’ Theory of Hot Flat Rolling: According to Sims (1954), the only practicable method of allowing for the elastic deformation of the rolls is that due to Hitchcock, who replaced the actual distribution of pressure over the roll surface with an elliptical distribution giving the same total load. The roll, in its arc of contact with the material, is then of constant radius of curvature. Sims‟ hot flat rolling theory assumes a circular arc of contact, which is flattened in accordance with Hitchcok‟s formular:  C .P  R` Ro1     .W  ……………………………… (2) where: R‟ = radius of curvature of the elastically deformed roll, (mm) Ro = un-deformed roll radius, (mm), P = vertical roll pressure, (N/mm2 ) W = width of the material, (mm), C = constant, and, C 8 1  v  2 E …………………………………(3) also, = 0.0223 mm2 kN-1 for steel rolls, = 0.0247 mm2 kN-1 for chilled C.I. rolls 2 P =132KN/ mm (Sims, 1954; Aiyedun, 1984) However, several authors have questioned the validity of this approach. 3. The Bland and Ford’s Theory: The Bland and Fords theory is basically a theory for cold rolling, where sliding takes place throughout the arc of contact but has been found applicable to hot rolling of HCSS316, where there is a mixed sticking - sliding condition (Aiyedun 1984). This is the situation for hot rolling of HCSS316 at (900 – 1200)oC, (0 – 15) % reduction, (0.07 – 1.5) s-1 strain rates. www.ijesi.org 60 | Page
  • 3. A Study Of Zenner – Holomon Parameter Variation… THE ROLL CHILLING EFFECT A detailed description of the Reverse Sandwich Model based on the „Roll Chilling Effect‟, which characterizes hot rolling of HCSS316 has been presented elsewhere; (Shobowale, (1998), Alamu, (2001), Alamu and Aiyedun, (2003)). The reverse sandwich rolling presents a situation whereby a high strength - metal clads a low strength metal. The strength variation being a direct consequence of drastic temperature changes during rolling. The reverse sandwich model predicts rolling temperatures, temperature distribution corresponding to different heights (17 Zones), the Zener-Hollomon parameter, yield stresses, rolling load and torque for HCSS316 rolled at low strain rates and low reduction. DEFORMATION IN MATERIAL AND ROLLING TEMPERATURE Extensive research work has been carried out on deformation modeling using the Zener-Hollomon parameter. A general drop in the Zener-Hollomon parameter from the rolling surfaces (lowest temperature zone) towards the core (temperature peak) of the material was observed by Alamu and Taiwo, (2002), implying that the material deforms increasingly towards the centre. The conclusion drawn was corroborated with the fact that metals deform at a greater rate at elevated temperatures (Early, 1977) PASS REDUCTION AND THE ZENER – HOLLOMON PARAMETER Reduction per pass during metal rolling process is given as: ……………………………………. (4)   Hf  Ho where;  = rolling reduction, (mm), Hf = final specimen thickness, (mm), Ho = initial specimen thickness, (mm). Expressed as a percentage, we have: r Hf  Ho  100% Ho …………………………………… (5) The Zener-Hollomon parameter was determined using the proposition of Zener and Hollomon, (1944):   Q      f    exp    f (Z )  RT   ……………………. (6)  = strain rate R = universal constant, (J /mol..K), T = absolute temperature, (OC) Z = Zener-Hollomon parameter. Q = energy supplied by the thermal fluctuation to overcome obstacles such as dislocations. The Z-values are uniquely related to the stress, and, hence the deformation of the material. For HCSS316 at (900 – 1200)oC, (0 – 15) % reduction, and (0.07 – 1.5) s-1 strain rates, Q = 460kJ / mol (Aiyedun, 1984). where; III. MEAN STRAIN RATE The resistance to deformation of hot metal is both strain and strain rate dependent. For this reason it is necessary to define the mean strain rate in the rolling pass. According to Orowan and Pascal, mean strain rate is given as;    Vn Rh1 1  3 r  4 r 1 r    …………………………(7) where; = rolling velocity at the neutral position. Vn Ford and Alexander expressed it in the form:    Vn Rh1  4  3r  r 2   2  r   …………………..(8) The form of mean strain rate estimation adopted by Sims, R. B. is given as:    Vn  1  ln  r 1  r   1 Rh1 ……………………(9) Integration of equation (9) into equation (6) above gives the basis of Zener – Hollomon Parameter computation adopted by Sims. (Aiyedun, (1984) According to Sellars, (1981) instantaneous strain rate in the roll gap is    2v h1  h 2 0.5 R 0 .5 h www.ijesi.org ……………………(10) 61 | Page
  • 4. A Study Of Zenner – Holomon Parameter Variation… He further stated that the best mean strain rate will be one that gives a correct mean flow stress. Farag and Sellars, (1973) thus obtained an approximate empirical equation of the form:  2 0.25    h1  0.45   1.08V     ln   R`0.5  0.5  h1h 2   h 2     ……………………………… (11) where:  = reduction V = peripheral velocity of rolls (mms -1) The above equation due to Farag and Sellars was adopted in the Reverse Sandwich Model for computation of mean strain rate, which was then used in equation (6) to estimate the Zener - Hollomon Parameter (The quantity used to model deformation). IV. MODEL SIMULATION AND VALIDATION The computer code developed using FORTRAN 77 for Zener - Hollomon Parameter computation at different rolling reduction using the Reverse sandwich model is as provided. Fig. 2 shows the flow chart for the simulation. The Program is user friendly and interactive, accepting input manually from the screen and outputting results to user-defined file. Validation of the program was accomplished using data from hot rolling experimental work carried out by authors on HCSS316 using 2 high reversing laboratory rolling mills. For the material under study, experimental data abound in literatures for hot rolling based on Sims‟ theory of hot flat rolling (Aiyedun, 1984; Shobowale, 1998; Alamu, 2001). The composition and thermo-mechanical history of the specimen is presented in Table I, while the input data for the simulation is as shown in Table II. V. RESULTS AND DISCUSSION The Output of the computer program, run with an IBM compatible Pentium (r) Processor, is presented in Tables III - VI. The tables show the Zener – Hollomon Parameter values corresponding to different rolling reduction characterized in different specimen. Also, the tables present the mean rolling temperature for each hot rolling schedule to enable further validation of the program via a comparison between simulated and experimental mean temperatures. This comparison is presented in Fig. 4. Similar data, from literatures, for hot flat rolling of HCSS316 adopting Sims‟ theory is presented in Table VII. These sets of data, processed with EXCEL package gave the polynomials shown in Fig. 3From the tables, variation of the Zener – Hollomon Parameter with rolling reduction is evident. This is in agreement with earlier works of authors (Shobowale, 1998; Alamu and Taiwo, 2002). In other words, the rate of deformation in HCSS316 during hot rolling is a function of the rolling reduction per pass. The possible relationship between these two parameters, as evident in Fig. 3, takes the form of a non-linear polynomial, and is consistent in the two approaches; the Reverse sandwich Model and Sims‟ theory. From the two approaches investigated, the Zener – Hollomon Parameter as a function of rolling reduction takes the form: ( Log 10Z   ar  br  cr  d ;...... a, b, c, d  cons tan ts ). For Sims‟ theory, a = -0.1833, b = 1.45, c = -2.8667, d = 21; while for Reverse Sandwich Model; a = 0.1367, b = -1.28, c = 3.9833, and, d = 16.82. 3 2 Fig. 4 reveals an agreement between simulated mean temperature and experimental values. Similar comparisons have been used in other works (Shobowale, 1998; Alamu and Aiyedun, 2002, Ojediran and Alamu, 2002) to confirm the validity of the output of the computer program. Hence, results obtained compares favourably with experimental inferences as well as earlier works of researchers. VI. CONCLUSION In the hot rolling of HCSS316 at low strain rates, (0.01 – 1.55) s-1 and low reductions, ( 10%), the Zener – Hollomon Parameter, (Z), has been found to be dependent on rolling reduction, (r), per pass. For Sims‟ theory, Log 10Z   0.1833 r  1.45 r  2.8667 r  21 ; while using the Reverse 3 2 sandwich Model, Log 10Z   0.1367 r  1.28 r  3.9833 r  16 .82 for hot rolling computations. 3 2 www.ijesi.org 62 | Page
  • 5. A Study Of Zenner – Holomon Parameter Variation… [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] REFERENCES Afonja, A. A. and Sansome, D. H. (1973), “A Theoretical Analysis of the Sandwich Rolling Process” Int. J. Mech. Sci., 15 (1): 1 – 14. Aiyedun, P. O. (1984) “A Study of Loads and Torques for Light Reduction in Hot Flat Rolling” Ph. D. Thesis, University of Sheffield. Aiyedun, P. O. (1986), “Hot Flat Rolling Simulation by Use of the Bland and Ford‟s Cold Rolling Theory for HCSS316 at Low Reduction and Low Strain Rates”, Proc, Int. AMSE Conf., 3 (1): 14 – 36. Alamu, O. J. (2001) “Integration of the Reverse Sandwich Model into the Hot Rolling Bland and Ford‟s Theory for Load and Torque Calculations”, M. Sc. Project Report, University of Ibadan, Ibadan, Nigeria. Alamu, O. J. and Aiyedun, P. O. (2003) “A Comparison of Temperature Gradient in Hot Rolling at Low and High Strain Rates” JSET, 10 (1) (In Press) Alamu, O. J. and Taiwo, A. “Computational Approach to a Study of Deformation in HCSS316 During Hot Rolling, The Nigerian Academic Forum, (In Press) Barbosa, R. A. N. M., (1983), Ph. D. Thesis, University of Sheffield. Early, J.G. (1977) “Elevated Temperature Mechanical Behaviour of a Carbon-Manganese Pressure Vessel Steel” Journal of Engineering Materials and Technology, pp. 359 – 365. Farag, M. M. and Sellars, C. M., (1979) “Hot Working and Forming Process”, Paper presented at Metals Society Conference, Sheffield. Graham, W. O., Peter, R. K. and Partrick, J. D. (1993) Steel Designer‟s Manual, 5th ed. Blackwell Scientific Publishers, London Leduc, L. A., (1980), Ph. D. Thesis, University of Sheffield. Lenard, J.G. (1980) “Roll Deformation in Cold Strip Rolling” Journal of Engineering Materials and Technology, 102 (1):382 – 383. Ojediran, J. O and Alamu, O. J (2002) “A study of Core Temperature Characteristics of Hot flat Rolled HCSS 316” International Journal of Research in Science and Education 2(2) Sellars, C. M. (1981) Paper presented at Colloque de Metallurgie, Institut National des Science et Technique Nucleaires, Sanclay. Shobowale, B. (1998) “The Reverse Sandwich Effect in HCSS316 Hot Flat Rolled at Low Strain Rates and Low Reductions”, M. Sc. Project Report, University of Ibadan, Ibadan, Nigeria. Sims, R.B. (1954) “The Calculation of Roll Force and Torque in Hot Rolling Mills” J.I.S.I. Pp. 191 – 200. Usamah, S. and Lenard, J. G. (1980) “A Comparison of Cold Rolling Theories Based on the Equilibrium Approach” Journal of Engineering Materials and Technology, 102 (1): 223 – 228. Zener, C. and Hollomon, J.H., (1944), Journal of Applied Physics, 15, 22. C------------------------------------------------------------------C Program : HOT ROLLING DEFORMATION BASED ON RSM MODEL C___________________________________________________________________ IMPLICIT REAL*8(A-H,O-Z) DIMENSION T(17),H(17),PLOT(17) CHARACTER RSM*20, SPNO*6,CONTD DATA IN/'N'/,IY/'Y'/ Q=460000.0 GKR=8.314 P=132.0 C=0.02474 RO=139.70 AZEN = 0.0 C FILES CREATION AND INTERACTIVE DATA ENTRY WRITE(*,*)'Enter a Filename for the Result.' READ(*,25)RSM OPEN(UNIT=7,FILE=RSM,STATUS='NEW') 10 WRITE(*,*)'Supply the Specimen Identification Number.' READ(*,12)SPNO www.ijesi.org 63 | Page
  • 6. A Study Of Zenner – Holomon Parameter Variation… WRITE(*,*)'Enter the Rolling Speed,(mm/s).' READ(*,*)V WRITE(*,*)'Supply the Furnace Temperature (Deg.Celcius).' READ(*,*)TF WRITE(*,*)'Supply the Initial Specimen Height,(mm).' READ(*,*)HO WRITE(*,*)'Enter the Final Specimen Height,(mm).' READ(*,*)HF WRITE(*,*) 'Enter the Width of the Specimen,(mm).' READ(*,*) W WRITE(7,*) WRITE(7,100)SPNO 100 FORMAT(1X,'OUTPUT FOR SPECIMEN 'A4) WRITE(7,*)'------------------------------------------' 12 FORMAT(A4) 20 FORMAT(A1) 25 FORMAT(A4) C RELATIONSHIP BETWEEN ROLLING SPEED(V) AND THE REVERSE SANDWICH C ROLLING MODEL CONSTANT(K) IF(V.LE.10.0) THEN AK=1.59 ELSE IF(V.LE.45.0) THEN AK=1.40 ELSE IF(V.LE.100.0) THEN AK=1.19 ELSE IF(V.LE.180.0) THEN AK=1.16 ELSE IF(V.LE.250.0) THEN AK=1.12 ELSE WRITE(7,*) "AK IS UNDEFINED" STOP END IF C CALCULATION OF REDUCTION(DEL), PERCENTAGE REDUCTION(DELPER) AND C DEFORMED ROLL RADIUS(DR) DEL = HO-HF DELPER=((HO-HF)/HO)*100 DR = RO*(1+(C*P)/(DEL*W)) C C C COMPUTATION OF MEAN TEMPERATURE(TMEAN),SURFACE TEMPERATURE(TE), TEMPERATURE DISTRIBUTION(TDIST), MIDDLE TEMPERATURE(TMID) AND TEMPERATURE VARIATION ALONG THICKNESS (T1.....T17) TMEAN = (TF+(TF/AK))/2.0 TMID = (TMEAN+TF)/2.0 TE = TF/AK TDIST = TMID-TE T(1) =TE DO 7 J=1,4 7 T(J+1) = T(J)+0.2*TDIST DO 8 J=5,7 8 T(J+1) = T(J) +0.04*TDIST T(9) = (TMEAN+TF)/2.0 M=0 DO 9 J=8,5,-1 www.ijesi.org 64 | Page
  • 7. A Study Of Zenner – Holomon Parameter Variation… M=M+1 9 T(J*2)=T(M*2) M1=3 DO 11 J=15,11,-2 T(J)=T(M1) 11 M1=M1+2 T(17)=T(1) C COMPUTATION OF STRAIN RATE SRT = ((1.08*V)/(DR*DEL)**0.5)*((DEL/(HO*HF))**0.25)*(ALOG(HO/HF) 1)**0.45 C C ESTIMATION OF THICKNESS VARIATION CORRESPONDING TO TEMPERATURE VARIATION (H1..............H17) ALONG HEIGHT H(1) = 0 H(2) = HO/17.0 DO 13 J=2,16 IF(J.EQ.8) THEN H(J+1) = HO/2.0 ELSE IF (J.EQ.16) THEN H(J+1) = HO ELSE H(J+1) = H(J)+1 END IF 13 CONTINUE C ESTIMATION OF ZENER HOLLOMON PARAMETER ALONG THICKNESS C (Z1.........Z17) DO 15 J = 1,17 PLOT(J) = ALOG10(SRT*DEXP(Q/(GKR*(T(J)+273)))) 15 CONTINUE DO 35 J = 1,17 35 AZEN = AZEN+PLOT(J) CONTINUE AZEN = AZEN/17.0 26 FORMAT(1X,'SPECIMEN NO. = 'A4) 27 FORMAT(1X,'MEAN TEMPERATURE,('C) = 'F7.2) 37 FORMAT(1X,'ZENER-HOLLOMON PARAMETER(LOG) = 'F5.2) 40 FORMAT(1X,'ROLLING REDUCTION,(%) = 'F5.2) WRITE(7,26)SPNO WRITE(7,27)TMEAN WRITE(7,40)DELPER WRITE(7,37)AZEN WRITE(7,*)'_____________________________________________' WRITE(*,29)RSM 29 FORMAT(1X,13HEnter, edit ,A14,14Hfor the output) 30 WRITE(*,*)'DO YOU WISH TO CONTINUE?(Y/N)' READ(*,20)CONTD IF(CONTD.EQ.IY) GO TO 10 IF(CONTD.EQ.IN) GO TO 31 WRITE(*,*)'INVALID RESPONSE !! ENTER (Y/N) USING UPPERCASE LETTER' GO TO 30 31 STOP END www.ijesi.org 65 | Page
  • 8. A Study Of Zenner – Holomon Parameter Variation… Table I: Chemical Compositions and Thermo-mechanical Data for HCSS316 Element in HCSS316 C S Mo Ni Si Cr W Mn Nb V Ti Co Cu N O Percentage Composition (%wt) 0.054 0.016 2.050 11.300 0.540 17.400 <0.020 1.370 0.100 0.070 0.040 0.140 0.320 524ppm 122ppm Preliminary Measurement Mean Grain Size, (m) Aspect Ratio Micro hardness HV (kg/mm2) Temperature, (OC) 0.2% P. S., (N/mm2) Ultimate Tensile Strength, (N/mm2) Elongation, (%) Reduction in Area, (%) Value 39.30 1.02 165.00 20.00 246.00 595.00 67.00 66.00 TABLE II: The Reverse Sandwich Rolling Experimental Data*. S/N SPEC. FURN. THICKNESS WIDTH ROLLING NO. TEMP. INIT. FINL. SPEED (OC) (mm) (mm) (mm) (mm/s) 1 2 3 4 H50 H51 H52 H53 1120 14.17 12.73 75.17 1128 12.03 10.82 75.20 1123 10.04 09.09 75.20 1122 08.03 07.40 75.23 *(Aiyedun,1984) 009.32 009.32 009.32 009.32 TABLE III: OUTPUT FOR SPECIMEN H50 -------------------------------------SPECIMEN NO. = H50 MEAN TEMPERATURE,('C) = 912.20 ROLLING REDUCTION,(%) = 10.16 ZENER-HOLLOMON PARAMETER(LOG) = 19.66 ______________________________________ TABLE IV: OUTPUT FOR SPECIMEN H51 -------------------------------------SPECIMEN NO. = H51 MEAN TEMPERATURE,('C) = 918.72 ROLLING REDUCTION,(%) = 10.06 ZENER-HOLLOMON PARAMETER(LOG) = 20.76 ______________________________________ TABLE V: OUTPUT FOR SPECIMEN H52 -------------------------------------SPECIMEN NO. = H52 MEAN TEMPERATURE,('C) = 914.64 ROLLING REDUCTION,(%) = 9.46 ZENER-HOLLOMON PARAMETER(LOG) = 20.94 ______________________________________ www.ijesi.org 66 | Page
  • 9. A Study Of Zenner – Holomon Parameter Variation… TABLE VI: OUTPUT FOR SPECIMEN H53 -------------------------------------SPECIMEN NO. = H53 MEAN TEMPERATURE,('C) = 913.83 ROLLING REDUCTION,(%) = 7.85 ZENER-HOLLOMON PARAMETER(LOG) = 21.02 ______________________________________ Table VII: *Values Obtained for the Specimens Using Sims‟ Theory. S /N 1 2 3 4 Specimen Identification Number H50 H51 H52 H53 Rolling Reduction (%) 10.16 10.06 9.46 7.85 Log10(Z) 19.40 19.60 20.50 21.00 *Shobowale,(1998) Frictional force Normal force Hard Matrix HO Soft Clad Hard Matrix Hf Roll FIG. 1 Schematic Illustration of Reverse Sandwich Rolling Process. www.ijesi.org 67 | Page
  • 10. A Study Of Zenner – Holomon Parameter Variation… START READ: SP.NO, V, Tf, H0, W, Hf NO NO NO NO NO IS V< 250? IS V< 180? IS V< 100? IS V< 45? YES YES K = 1.59 K = 1.40 COMPUTE YES YES YES IS V< 10? K = 1.19 RED = HO - HF % RED = ((HO - HF) /HO))*100 DR = RO*(1+(C*P)/(RED*W)) Tm = (Tf+(Tf / K))/2 TCORE = (TM+ TF)/2 TS = Tf / K TDIST = TCORE - TS 0.25    h1  0.45 1.08V   2   ln   0.5 0.5    R`   h1h 2   h 2     K = 1.16   Q  LogZ  Log   exp     RT    K = 1.12 COUNTER J = 0 K = UNDEFINED COMPUTE J, T(J), H(J), LogZ NO YES IS J = 17 ? J =J+1 NO NO ALL SPECIMEN CONSIDERED? WRITE SP NO,Tm, ,%RED, LogZMEAN YES STOP Fig. 2: Flow Chart for the RSM Simulation www.ijesi.org 68 | Page
  • 11. A Study Of Zenner – Holomon Parameter Variation… 21.5 Zener - Hollomon Parameter 21 3 2 y = 0.1367x - 1.28x + 3.9833x + 16.82 R2 = 1 20.5 y = -0.1833x3 + 1.45x2 - 2.8667x + 21 R2 = 1 20 19.5 RSM 19 10.16 SIMS Poly. (RSM) Poly. (SIMS) 10.06 9.46 7.85 Rolling Reduction, (%) FIG.3: DEPENDENCE OF ZENER - HOLLOMON PARAMETER ON ROLLING REDUCTION BASED ON DIFFERENT ROLLING THEORIES 930 925 O Temperature, ( C) 920 915 910 MEAN; EXPERIMENTAL MEAN; SIMULATED 905 900 H50 H51 H52 H53 High Carbon Stainless Steel 316 Specimen. Fig. 4: VALIDATION OF SIMULATED RESULTS USING MEAN ROLLING TEMPERATURE ESTIMATION www.ijesi.org 69 | Page