STI 7552 Instruction Manual
•
0 j'aime•225 vues
Buy the STI 7552 at JMAC Supply. https://www.jmac.com/STI_7552_p/sti-7552.htm?=slideshare
Recommandé
Recommandé
Contenu connexe
Tendances
Tendances (7)
Similaire à STI 7552 Instruction Manual
Similaire à STI 7552 Instruction Manual (20)
Plus de JMAC Supply
Plus de JMAC Supply (20)
Dernier
Dernier (20)
STI 7552 Instruction Manual
- 1. INSTALLATION OF STI-7552, STI-7553 AND STI-7553AED PROTECTIVE CABINET All specifications and information shown were current as of publication and are subject to change without notice. 7552/53/53AEDIS MAY08 Safety Technology International, Inc. 2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: info@sti-usa.com Web: www.sti-usa.com Safety Technology International (Europe) Ltd. Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire • B98 0HU • England Tel: 44 (0) 1527 520 999 • Fax: 44 (0) 1527 501 999 E-mail: info@sti-europe.com • Web: www.sti-europe.com INSTALLATION OF CABINET 1. Insert the (5) mounting tabs fully into back box mounting tab slots. Use rubber mallet if necessary. 2. After selecting a suitable location, place cabinet in closed position, against the wall. Mark and drill (5) 1/4 in. diameter holes. Insert the (5) 19033 anchors. 3. Select (1) of the (2) shelf mounting locations, install shelf. Close and lock cabinet. 4. Place cabinet in position making sure the (2) switch wires are not pinched between the wall and cabinet. Drive in the (5) screws. Cabinet is now secure. Electronic warranty form at www.sti-usa.com/wc14 INSTALLATION OF ALARM ASSEMBLY 1. Place the alarm mounting plate on the top center of cabinet. Select at least two of the four optional mounting holes. Mark and drill 3/16 in. holes and install the 19018 anchors. 2. Fish the magnetic switch wires through the alarm mounting plate and the siren backplate (View A). Next, drive the two alarm mounting screws into the previous installed anchors. 3. Install the two magnetic switch wires following the terminal switch diagram (View B on reverse side). 4. Install the alarm cover using the (2) tamperproof screws and provided tool. CLEANING INSTRUCTIONS Rinse with water to remove abrasive dust and dirt. Wash with soap or mild detergent, using a soft cloth. (Do not scrub or use brushes or abrasives.) Rinse once more, then dry using a soft cloth or chamois. To remove grease or wet paint, rub gently with a cloth wetted thoroughly with naphtha (do not use razor blades or gasoline) then wash and rinse. STOPEMERGENCY USE ONLY ALARM SOUNDS WHEN CABINET IS OPENED 19039 #6 x 1 1/4 in. PAN HEAD SCREW (4) PROVIDED TERMINAL BLOCK SEE CIRCUIT BOARD SET-UP FOR CONNECTION & OPERATION DETAILS SIREN BACKPLATE ALARM MOUNTING PLATE REED SWITCH WIRES 19018 #8-10 PLASTIC ANCHOR (4) PROVIDED 9 VOLT BATTERY 19011 #8-32 x 3/8 in. TRUSS HEAD TAMPERPROOF SCREW 19016 TAMPER WRENCH POLYCARBONATE COVER MAGNET MAGNETIC CONTACT REED SWITCH ON UNITS WITH ALARM OPTIONAL TAB MOUNTING LOCATION ROTARY ACTION LATCH (2) PROVIDED SHOWN WITH COVER CLOSED19033 ANCHOR (6) PROVIDED 19002 SCREW #8-32 x 3/8 in. (4) PROVIDED 6297550 GASKET 19013 SCREW #10 x 1 1/2 in. (6) PROVIDED 06297T MOUNTING TABS (6) PROVIDED AED 07550WR WIRE SHELF 04876 MOUNTING PLATE 19002 SCREW #8-32 x 3/8 in. (4) PROVIDED OPTIONAL 07551WR WIRE RACK ATTACH WITH (4) 19002 SCREWS AND (4) 19055 #8-32 KEPS NUTS PROVIDED ALARM MOUNTING PLATE CABINET WIRE ACCESS HOLE ROUTE THE 2 SWITCH WIRES THROUGH THE HOLE AS SHOWN VIEW A OPTIONAL MOUNTING HOLES (4) EMERGENCY USE ONLY AED 27.5 in.(699mm) 19.75 in. (502mm) 24.75 in. (629mm) FRONT R.H. SIDE STI-7553AED 2.25 in. (57mm) 7.31 in. (186mm) 3/8” DIA. STOPEMERGENCY USE ONLY ALARM SOUNDS WHEN CABINET IS OPENED 19039 #6 x 1 1/4 in. PAN HEAD SCREW (4) PROVIDED TERMINAL BLOCK SEE CIRCUIT BOARD SET-UP FOR CONNECTION & OPERATION DETAILS SIREN BACKPLATE ALARM MOUNTING PLATE REED SWITCH WIRES 19018 #8-10 PLASTIC ANCH (4) PROVIDED 9 VOLT BA 19011 #8- TRUSS HEA TAMPERPR SCREW 19016 TA POLYCARBONATE COVER MAGNET MAGNETIC CONTACT REED SWITCH ON UNITS WITH ALARM OPTIONAL MOUNTING ROTARY AC LATCH (2) PR SHOWN WITH CO19033 ANCHOR (6) PROVIDED 19002 SCREW #8-32 x 3/8 in. (4) PROVIDED 6297550 GASKET 19013 SCREW #10 x 1 1/2 in. (6) PROVIDED 06297T MOUNTI (6) PROV AED 07550WR WIRE SHELF 04876 MOUNTING PLATE 19002 SCREW #8-32 x 3/8 in. (4) PROVIDED OPTIONAL 07551WR WIRE RACK ATTACH WITH (4) 19002 SCREWS AND (4) 19055 #8-32 KEPS NUTS PROVIDED ALARM MOUNTING PLATE CABINET WIRE ACCESS HOLE ROUTE THE 2 SWITCH WIRES THROUGH THE HOLE AS SHOWN VIEW A OPTIONAL MOUNTING HOLES (4) EMERGENCY USE ONLY AED 27.5 in.(699mm) 19.75 in. (502mm) 24.75 in. (629mm) FRONT R.H. SIDE STI-7553AED 2.25 in. (57mm) 7.31 in. (186mm) 3/8” DIA. STOPEMERGENCY USE ONLY ALARM SOUNDS WHEN CABINET IS OPENED 19039 #6 x 1 1/4 in. PAN HEAD SCREW (4) PROVIDED TERMINAL BLOCK SEE CIRCUIT BOARD SET-UP FOR CONNECTION & OPERATION DETAILS SIREN BACKPLATE ALARM MOUNTING PLATE REED SWITCH WIRES 19018 #8-1 PLASTIC ANC (4) PROVIDE 9 VOLT B 19011 #8 TRUSS HEA TAMPERP SCREW 19016 T POLYCARBONATE COVER MAGNET MAGNETIC CONTACT REED SWITCH ON UNITS WITH ALARM OPTIONAL MOUNTIN ROTARY A LATCH (2) P SHOWN WITH C19033 ANCHOR (6) PROVIDED 19002 SCREW #8-32 x 3/8 in. (4) PROVIDED 6297550 GASKET 19013 SCREW #10 x 1 1/2 in. (6) PROVIDED 06297T MOUNT (6) PRO AED 07550WR WIRE SHELF 04876 MOUNTING PLATE 19002 SCREW #8-32 x 3/8 in. (4) PROVIDED OPTIONAL 07551WR WIRE RACK ATTACH WITH (4) 19002 SCREWS AND (4) 19055 #8-32 KEPS NUTS PROVIDED ALARM MOUNTING PLATE CABINET WIRE ACCESS HOLE ROUTE THE 2 SWITCH WIRES THROUGH THE HOLE AS SHOWN VIEW A OPTIONAL MOUNTING HOLES (4) EMERGENCY USE ONLY AED 27.5 in.(699mm) 19.75 in. (502mm) 24.75 in. (629mm) FRONT R.H. SIDE STI-7553AED 2.25 in. (57mm) 7.31 in. (186mm) 3/8” DIA.