This document summarizes an experiment measuring the rate of heat transfer using different materials as containers. The materials tested were styrofoam, foam, metal, and paper. It was predicted that metal would transfer heat the fastest due to being a conductor, but the results showed that paper transferred heat the fastest, with a rate of 4.4°C/min. The experiment concluded that inconsistencies in room temperature and difficulty maintaining the starting water temperature of 60°C affected the results. More precise temperature control could improve the experiment.
1. Paul Laohapiengsak
Geoscience
Ms. Perkins
Period 2
Heat Transfer
Introduction:
Energy refers to “the capacity of a physical system to do work”. Nowadays, energy
plays a vital role in humans’ lives. It provides mankind with a convenience life style ranging
from transportation to many electronic devices. According to the law of conservation of
energy, “Energy can never be created or destroyed, only transformed from one form to
another”. Nevertheless, energy transfer can result in heat. Furthermore, energy can also be in
various forms such as kinetic, potential, sound, gravitational, and elastic energy.
There are mainly two forms of energy, which are renewable and renewable source of
energy. The examples of renewable energy source are wind and water while the
nonrenewable sources of energy arecoals and gasoline. Although energy are extremely
beneficial to human beings, nevertheless some sources of energy when consumed can result
in many negative impacts to the environment such as burning coals will create air pollution.
For this reason, human beings should consider not only preserving energy but also beware of
the negative impacts it will cause upon nature.
The purpose of this lab is to measure rate of heat transfer. In this investigation, many
objects will be used as containers of heat energy, in this case “hot water”, which are metal,
foam, paper, and Styrofoam. The temperature of each container will be recorded carefully
base on the amount of time it takes for the temperature of the objects to decrease. The starting
temperature of a 50 milliliters hot water will be 60° Celsius. As metal has the property of
faster heat transfer, it is predicted that, it will cool down faster than the other objects. For this
reason, it is predicted that objects that is a heat conductor will have a high rate of heat
transfer.
Research Question: What type of container has the capability of fastest heat transfer?
Variables:
Independent Variables: Types of container
Dependent Variables: Temperature of water in the given container, the cooling rate
Controlled Variables: Starting temperature, amount of time given for heat transfer, the room
temperature where the investigation is conducted, and the amount of hot water
2. Materials:
Water
Hot plate or Water Heater
Containers: Styrofoam, Foam, Metal, and Paper (3 containers per each type).
Beaker – 1000 milliliters
Beaker – 250 milliliters
Thermometer
Pipette
Stop Watch
Procedure:
1. Fill in the 1000 milliliters beaker with water until it is almost full
2. Place the 1000 milliliters beaker on the hot plate
3. Turn on the hot plate and heat the water
4. Measure the water in the beaker until it is 60 degrees Celsius
5. Pour the heated water from the 1000 milliliters beaker into the 250 milliliters
beakers until it is 50 milliliters depth
6. Use the pipette to adjust the amount of water in the 250 milliliters beakers as close
as possible to 50 milliliters depth
7. Pour the water from the 250 milliliters beakers into the containers
8. Place thermometers into each containers
9. Start the timer
10. (After 5 minutes) Record the temperature of water in each container
11. Repeat steps 4-10 with new containers for 3 times
12. Collect the data carefully
Data Collection:
During the observation, it was noticed that at 60 degrees Celsius, there are plenty of water
vapor. The vapor can be seen very easily when it rose against the surface of the medal
container.
Table 1: Temperature of Water
Types of Container Temperature of Water (°C) ± 0.5 Uncertainties Average Temperature of Water (°C)
Test 1 Test 2 Test 3
Styrofoam 48.0°C 49.0°C 49.0°C ± .5°C 48.0°C
Foam 45.0°C 47.0°C 43.0°C ± 2.0°C 45.0°C
Metal 33.0°C 37.0°C 35.0°C ± 2.0°C 35.0°C
Paper 38.0°C 34.0°C 33.0°C ± 2.5°C 34.6°C
Table 2: Heat Transfer Rate
Type of Container Transfer Rate of Heat (°C / Min) Uncertainties
Styrofoam 2.0°C ± 1%
Foam 2.6°C ± 3%
Metal 4.2°C ± 3%
Paper 4.4°C ± 4%
3. Sample Calculations:
Average temperature of water Heat Transfer Rate Uncertainty
Styrofoam = (48 + 47 + 49) / 3 Styrofoam = (60 – 48) / 5 Styrofoam (49-48) / 2
= 48.00°C = 2.4°C = ± .5°C
Graph 1: The transfer rate of heat of each container
Transfer Rate of Heat (°C / Min)
8
7
6
5
4 Transfer Rate of Heat (°C /
3 Min)
2
1
0
Styrofoam Foam Metal Paper
The graph shown above demonstrates the rate of heat transfer in each container. Note that
Paper has the highest rate of transfer while Styrofoam has the lowest. The uncertainty is
shown in the graph above to indicate the range of values of rate of heat transfer. The tests of
heat transfer were tested for three times.
Conclusion and evaluation:
According to the data collection, the metal container did not have the fastest rate of
heat transfer as predicted. It can be seen form the data collection that paper has the fastest rate
of heat of 4.4°C when compared to the Styrofoam which has the lowest rate of heat transfer
of only about 2.0°C. In addition, metal, the object that was predicted to have the fastest heat
transfer rate was fairly close with 4.4°C rate of heat transfer.
The uncertainties in this investigation are calculated for the fact that there are ranges
of values in each investigation. It was quite extraordinary how the paper which has the
starting temperature of 60°C where its temperature dropped to about 34°C within only five
minutes. Paper was not predicted to have the fastest heat transfer for the fact that it is not a
conductor of heat. On the other hand, metal, which could be seen in various occasions to
attract large amount of heat such as cars that are out in the sun, was predicted to have fastest
heat transfer is because it is a better conductor. Nevertheless, after the investigation, it was
strange to have had found out that paper has the faster heat transfer rate.
4. The major weaknesses of this investigation are the room temperature that is not
constant. This inconstant room temperature maybe the root cause of temperature changes
where the data was collected within two days period. In addition, because the water
temperature changes all the time, it cannot be kept at constant rate of 60°C. Therefore, it is
difficult to make sure that the starting temperature is 60°C in every trials. To improve this
investigation, the trials should be conducted in one day to make sure that there will be least
room temperature changes. Also, more efficient tools can be used to control the temperature
as precise as possible such as special room that has constant room temperature.