Fanuc 16i 18i alarms

Fanuc 16i 18i Alarms Codes
You can Join at Our Group
Facebook : CNC INDONESIA or Email :soekarno.gempar@gmail
Fanuc 16i 18i Alarms Codes for CNC machinists.
These Fanuc alarm code applies to following Fanuc CNC controls
 Fanuc 16i/18i Model A
 Fanuc 16i/18i Model B
 Fanuc 16iLModel A
 Fanuc 16iP Model A
 Fanuc 16iP/18iP Model B
FANUC 18i-MB
Contents
 Fanuc 16i 18i Alarms
o Program errors (P/S alarm)
o Laser alarms
o Background edit alarm
o Absolute pulse coder (APC) alarms
o Serial pulse coder (SPC) alarms
o Servo alarms
o Over travel alarms
o Overheat alarms

o Rigid tapping alarms
o Serial Spindle alarms
o Safety zone alarms
o System alarms
Fanuc 16i 18i Alarms

Program errors (P/S alarm)
 0 PLEASE TURN OFF POWER
 1 TH PARITY ALARM
 2 TV PARITY ALARM
 3 TOO MANY DIGITS
 4 ADDRESS NOT FOUND
 5 NO DATA AFTER ADDRESS
 6 ILLEGAL USE OF NEGATIVE SIGN
 7 ILLEGAL USE OF DECIMAL POINT
 9 ILLEGAL ADDRESS INPUT
 10 IMPROPER G–CODE
 11 NO FEEDRATE COMMANDED
 14 CAN NOT COMMAND G95 (M series)
 14 ILLEGAL LEAD COMMAND (T series)
 15 TOO MANY AXES COMMANDED (M series)
 15 TOO MANY AXES COMMANDED (T series)
 20 OVER TOLERANCE OF RADIUS
 21 ILLEGAL PLANE AXIS COMMANDED
 22 NO CIRCLE RADIUS
 23 ILLEGAL RADIUS COMMAND (T series)
 25 CANNOT COMMAND F0 IN G02/G03 (M series)
 27 NO AXES COMMANDED IN G43/G44 (M series)
 28 ILLEGAL PLANE SELECT
 29 ILLEGAL OFFSET VALUE (M series)
 29 ILLEGAL OFFSET VALUE (T series)
 30 ILLEGAL OFFSET NUMBER (M series)
 30 ILLEGAL OFFSET NUMBER (T series)
 31 ILLEGAL P COMMAND IN G10
 32 ILLEGAL OFFSET VALUE IN G10
 33 NO SOLUTION AT CRC (M series)
 33 NO SOLUTION AT CRC (T series)
 34 NO CIRC ALLOWED IN ST–UP /EXT BLK (M series)
 34 NO CIRC ALLOWED IN ST–UP /EXT BLK (T series)
 35 CAN NOT COMMANDED G39 (M series)
 35 CAN NOT COMMANDED G31 (T series)
 36 CAN NOT COMMANDED G31 (M series)
 37 CAN NOT CHANGE PLANE IN CRC (M seires)
 37 CAN NOT CHANGE PLANE IN NRC (T seires)
 38 INTERFERENCE IN CIRCULAR BLOCK (M seires)
 38 INTERFERENCE IN CIRCULAR BLOCK (T series)
 39 CHF/CNR NOT ALLOWED IN NRC (T series)
 40 INTERFERENCE IN G90/G94 BLOCK (T series)
 41 INTERFERENCE IN CRC (M seires)
 41 INTERFERENCE IN NRC (T seires)
 42 G45/G48 NOT ALLOWED IN CRC (M series)

 43 ILLEGAL T–CODE COMMAND (Fanuc 16iLModel A)
 44 G27–G30 NOT ALLOWED IN FIXED CYC (M series)
 45 ADDRESS Q NOT FOUND (G73/G83) (M series)
 46 ILLEGAL REFERENCE RETURN COMMAND
 47 ILLEGAL AXIS SELECT
 48 BASIC 3 AXIS NOT FOUND
 49 ILLEGAL OPERATION (G68/G69) (M series)
 50 CHF/CNR NOT ALLOWED IN THRD BLK (M series)
 50 CHF/CNR NOT ALLOWED IN THRD BLK(T series)
 51 MISSINGMOVE AFTER CHF/CNR (M series)
 51 MISSINGMOVE AFTER CHF/CNR (T series)
 52 CODE IS NOT G01 AFTER CHF/CNR (M series)
 52 CODE IS NOT G01 AFTER CHF/CNR (T series)
 53 TOO MANY ADDRESS COMMANDS (M series)
 53 TOO MANY ADDRESS COMMANDS (T seires)
 54 NO TAPER ALLOWED AFTER CHF/CNR (T series)
 55 MISSINGMOVE VALUE IN CHF/CNR (M series)
 55 MISSINGMOVE VALUE IN CHF/CNR (T series)
 56 NO END POINT & ANGLE IN CHF/CNR (T series)
 57 NO SOLUTION OF BLOCK END (T series)
 58 END POINT NOT FOUND (M series)
 58 END POINT NOT FOUND (T series)
 59 PROGRAM NUMBER NOT FOUND
 60 SEQUENCE NUMBER NOT FOUND
 61 ADDRESS P/Q NOT FOUND IN G70–G73 (T series)
 62 ILLEGAL COMMAND IN G71–G76 (T series)
 63 SEQUENCE NUMBER NOT FOUND (T series)
 64 SHAPE PROGRAMNOT MONOTONOUSLY(T series)
 65 ILLEGAL COMMAND IN G71–G73 (T series)
 66 IMPROPER G–CODE IN G71–G73 (T series)
 67 CAN NOT ERROR IN MDIMODE (T series)
 69 FORMAT ERROR IN G70– G73 (T series)
 70 NO PROGRAM SPACE IN MEMORY
 71 DATA NOT FOUND
 72 TOO MANY PROGRAMS
 73 PROGRAM NUMBER ALREADY IN
 74 ILLEGAL PROGRAMNUMBER
 75 PROTECT
 76 ADDRESS P NOT DEFINED
 77 SUB PROGRAM NESTING ERROR
 78 NUMBER NOT FOUND
 79 PROGRAM VERIFY ERROR
 80 G37 ARRIVAL SIGNAL NOT ASSERTED (M series)
 80 G37 ARRIVAL SIGNAL NOT ASSERTED (T series)
 81 OFFSET NUMBER NOT FOUND IN G37 (M series)
 81 OFFSET NUMBER NOT FOUND IN G37 (T series)

 82 H–CODE NOT ALLOWED IN G37 (M series)
 82 T–CODE NOT ALLOWED IN G37 (T series)
 83 ILLEGAL AXIS COMMAND IN G37 (M series)
 83 ILLEGAL AXIS COMMAND IN G37 (T series)
 85 COMMUNICATIONERROR
 86 DR SIGNAL OFF
 87 BUFFER OVERFLOW
 88 LAN FILE TRANS ERROR (CHANNEL–1)
 89 LAN FILE TRANS ERROR (CHANNEL–2)
 90 REFERENCE RETURN INCOMPLETE
 91 REFERENCE RETURN INCOMPLETE
 92 AXES NOT ON THE REFERENCE POINT
 94 P TYPE NOT ALLOWED (COORD CHG)
 95 P TYPE NOT ALLOWED (EXT OFS CHG)
 96 P TYPE NOT ALLOWED (WRK OFS CHG)
 97 P TYPE NOT ALLOWED (AUTO EXEC)
 98 G28 FOUND IN SEQUENCE RETURN
 99 MDI EXEC NOT ALLOWED AFT. SEARCH
 100 PARAMETERWRITE ENABLE
 101 PLEASE CLEAR MEMORY
 109 FORMAT ERROR IN G08 (M series)
 110 DATA OVERFLOW
 111 CALCULATED DATA OVERFLOW
 112 DIVIDED BY ZERO
 113 IMPROPER COMMAND
 114 FORMAT ERROR IN MACRO
 115 ILLEGAL VARIABLE NUMBER
 116 WRITE PROTECTED VARIABLE
 118 PARENTHESIS NESTING ERROR
 119 ILLEGAL ARGUMENT
 122 FOUR FOLDMACROMODAL– CALL
 123 CAN NOT USE MACRO COMMAND IN DNC
 124 MISSING END STATEMENT
 125 FORMAT ERROR IN MACRO
 126 ILLEGAL LOOP NUMBER
 127 NC, MACRO STATEMENT IN SAME BLOCK
 128 ILLEGALMACRO SEQUENCE NUMBER
 129 ILLEGAL ARGUMENT ADDRESS
 130 ILLEGAL AXIS OPERATION
 131 TOO MANY EXTERNALALARMMESSAGES
 132 ALARM NUMBER NOT FOUND
 133 ILLEGAL DATA IN EXT. ALARM MSG
 135 ILLEGAL ANGLE COMMAND (M series)
 135 SPINDLE ORIENTATION PLEASE (T series)
 136 ILLEGAL AXIS COMMAND (M series)
 136 C/H–CODE & MOVE CMD IN SAME BLK. (T series)

 137 M–CODE & MOVE CMD IN SAME BLK.
 138 SUPERIMPOSEDDATA OVERFLOW
 139 CAN NOT CHANGE PMC CONTROL AXIS
 141 CAN NOT COMMAND G51 IN CRC (M series)
 142 ILLEGAL SCALE RATE (M series)
 143 SCALEDMOTION DATA OVERFLOW(M series)
 144 ILLEGAL PLANE SELECTED (M series)
 145 ILLEGAL CONDITIONS IN POLAR COORDINATE INTERPOLATION
 146 IMPROPER G CODE
 148 ILLEGAL SETTING DATA (M series)
 149 FORMAT ERROR IN G10L3 (M series)
 150 ILLEGAL TOOL GROUP NUMBER
 151 TOOL GROUP NUMBER NOT FOUND
 152 NO SPACE FOR TOOL ENTRY
 153 T–CODE NOT FOUND
 154 NOT USING TOOL IN LIFE GROUP (M series)
 155 ILLEGAL T–CODE IN M06 (M series)
 155 ILLEGAL T–CODE IN M06 (T series)
 156 P/L COMMAND NOT FOUND
 157 TOO MANY TOOL GROUPS
 158 ILLEGAL TOOL LIFE DATA
 159 TOOL DATA SETTING INCOMPLETE
 160 MISMATCHWAITINGM–CODE (T series (At two–path))
 160 G72.1 NESTING ERROR (M series))
 161 ILLEGAL P OF WAITINGM–CODE (T series (three–path control)
 161 G72.1 NESTING ERROR (M series)
 163 COMMAND G68/G69 INDEPENDENTLY T series (At two–path)
 169 ILLEGAL TOOL GEOMETRY DATA (At two–path) (Fanuc 16i/18i Model A)
 175 ILLEGAL G107 COMMAND
 176 IMPROPER G–CODE IN G107 (M series)
 176 IMPROPER G–CODE IN G107 (T series)
 177 CHECK SUM ERROR (G05 MODE)
 178 G05 COMMANDED IN G41/G42 MODE
 179 PARAM. (NO. 7510) SETTING ERROR
 180 COMMUNICATIONERROR (REMOTE BUF)
 181 FORMAT ERROR IN G81 BLOCK (Hobbingmachine, EGB) (M series)
 182 G81 NOT COMMANDED (Hobbingmachine) (M series)
 183 DUPLICATE G83 (COMMANDS) (Hobbingmachine) (M series)
 184 ILLEGAL COMMAND IN G81 (Hobbingmachine, EGB) (M series)
 185 RETURN TO REFERENCE POINT (Hobbingmachine) (M series)
 186 PARAMETER SETTING ERROR (Hobbing machine, EGB) (M series)
 190 ILLEGAL AXIS SELECT (M series)
 194 SPINDLE COMMAND IN SYNCHRO–MODE
 195 MODE CHANGE ERROR (Fanuc 16iLModel A)
 197 C–AXIS COMMANDED IN SPINDLE MODE
 199 MACROWORD UNDEFINED

 200 ILLEGAL S CODE COMMAND
 201 FEEDRATE NOT FOUND IN RIGID TAP
 202 POSITION LSI OVERFLOW
 203 PROGRAMMISS AT RIGID TAPPING
 205 RIGID MODE DI SIGNAL OFF
 206 CAN NOT CHANGE PLANE (RIGID TAP) (M series)
 207 RIGID DATA MISMATCH
 210 CAN NOT COMANDM198/M199
 211 G31 (HIGH) NOT ALLOWED IN G99
 212 ILLEGAL PLANE SELECT (M series)
 212 ILLEGAL PLANE SELECT (T series)
 213 ILLEGAL COMMAND IN SYNCHRO–MODE
 213 ILLEGAL COMMAND IN SYNCHRO–MODE (T series)
 214 ILLEGAL COMMAND IN SYNCHRO–MODE
 217 DUPLICATE G51.2 (COMMANDS) (T series)
 218 NOT FOUND P/Q COMMAND IN G251 (T series)
 219 COMMAND G250/G251 INDEPENDENTLY(T series)
 220 ILLEGAL COMMAND IN SYNCHR–MODE(T series)
 221 ILLEGAL COMMAND IN SYNCHR–MODE(T series)
 222 DNC OP. NOT ALLOWED IN BG.–EDIT (M series)
 224 RETURN TO REFERENCE POINT (M series)
 224 RETURN TO REFERENCE POINT (T series)
 225 SYNCHRONOUS/MIXED CONTROL ERROR (T series (At two–path))
 226 ILLEGAL COMMAND IN SYNCHRO– MODE (T series (At two–path))
 229 CAN NOT KEEP SYNCHRO–STATE (T series)
 230 R CODE NOT FOUND (Grindingmachine) (M series)
 231 ILLEGAL FORMAT IN G10 OR L50
 232 TOO MANY HELICALAXIS COMMANDS
 233 DEVICE BUSY
 239 BP/S ALARM
 240 BP/S ALARM
 241 ILLEGAL FORMAT IN G02.2/G03.2 (M series)
 242 ILLEGAL COMMAND IN G02.2/G03.2 (M series)
 243 OVER TOLERANCE OF END POINT (M series)
 244 P/S ALARM(T series)
 245 T–CODE NOT ALOWEE IN THIS BLOCK (T series)
 246 ENCODE PROGRAM NUMBER ERROR
 247 ILLEGAL CODE USED FOR OUTPUT
 250 Z AXIS WRONG COMMAND (ATC) (M series)
 251 ATC ERROR (M series)
 252 ATC SPINDLE ALARM (M series)
 253 G05 IS NOT AVAILABLE (M series)
 4000 P/S ALARM (Fanuc 16iLModel A)
 4002 UNAVAILABLE G–CODE IN SEARCH (Fanuc 16iLModel A)

 4004 3–D COORD. CONV. ALARM (Fanuc 16iLModel A)
 4010 3–D TRANSFORMFORMAT ERROR (Fanuc 16iLModel A)
 4011 CANNOTMAKE MATRIX (Fanuc 16iLModel A)
 4012 CANNOT CONVERT (Fanuc 16iLModel A)
 4500 REPOSITIONING INHIBITED
 4502 ILLEGAL COMMAND IN BOLT HOLE
 4503 ILLEGAL COMMAND IN LINE AT ANGLE
 4504 ILLEGAL COMMAND IN ARC
 4505 ILLEGAL COMMAND IN GRID
 4506 ILLEGAL COMMAND IN SHARE PROOFS
 4507 ILLEGAL COMMAND IN SQUARE
 4508 ILLEGAL COMMAND IN RADIUS
 4509 ILLEGAL COMMAND IN CUT AT ANGLE
 4510 ILLEGAL COMMAND IN LINE-PUNCH
 4511 ILLEGAL COMMAND IN CIRCLE-PUNCH
 4520 T, M INHIBITED IN NIBBLING-MODE
 4521 EXCESS NIBBLINGMOVEMENT (X, Y)
 4522 EXCESS NIBBLINGMOVEMENT (C)
 4523 ILLEGAL COMMAND IN CIRCLE-NIBBL
 4524 ILLEGAL COMMAND IN LINE-NIBBL
 4530 A/BMACRO NUMBER ERROR
 4531 U/V MACRO FORMAT ERROR
 4532 IMPROPER U/V MACRO NUMBER
 4533 U/V MACROMEMORY OVERFLOW
 4534W MACRO NUMBER NOT FOUND
 4535 U/V MACRO NESTING ERROR
 4536 NO W, Q COMMAND IN MULTI-PIECE
 4537 ILLEGAL Q VALUE IN MULTI-PIECE
 4538W NO. NOT FOUND IN MULTI-PIECE
 4539 MULTI-PIECE SETTING IS ZERO
 4540 MULTI-PIECE COMMANDWITHIN MACRO
 4542 MULTI-PIECE COMMAND ERROR
 4543 MULTI-PIECE Q COMMAND ERROR
 4544 MULTI-PIECE RESTART ERROR
 4549 ILLEGAL TOOL DATA FORMAT
 4600 T, C COMMAND IN INTERPOLATION
 4601 INHIBITED T, M COMMAND
 4602 ILLEGAL T-CODE
 4603 C AXIS SYNCHRONOUS ERROR

 4605 NEED ZRN
 4606 A T COMMANDWAS ISSUED (Fanuc 16iP Model A/B – 18iP Model B)
 4630 ILLEGAL COMMAND IN LASER MODE
 4631 ILLEGAL COMMAND IN PUNCHMODE (Fanuc 16i/18i Model A)
 4650 IMPROPER G-CODE IN OFFSETMODE
 4700 PROGRAM ERROR (OT +)
 4701 PROGRAM ERROR (OT –)
 5000 ILLEGAL COMMAND CODE (M series)
 5003 ILLEGAL PARAMETER (HPCC) (M series)
 5004 HPCC NOT READY
 5006 TOO MANYWORD IN ONE BLOCK (M series)
 5007 TOO LARGE DISTANCE (M series)
 5009 PARAMETER ZERO (DRY RUN) (M series)
 5010 END OF RECORD
 5011 PARAMETER ZERO(CUTMAX) (M series) (Fanuc 16i/18i Model A)
 5012 G05 P10000 ILLEGAL START UP (HPCC) (M series)
 5013 HPCC: CRC OFS REMAIN AT CANCEL (M series)
 5014 TRACE DATA NOT FOUND (M series)
 5015 NO ROTATION AXIS (M series) (M series)
 5016 ILLEGAL COMBINATIONOFM CODE
 5018 POLYGON SPINDLE SPEED ERROR (T series)
 5020 PARAMETER OF RESTART ERROR
 5030 ILLEGAL COMMAND (G100) (T series)
 5031 ILLEGAL COMMAND (G100, G102, G103) (T series)
 5032 NEW PRG REGISTERED IN B– AXS MOVE (T series)
 5033 NO PROG SPACE IN MEMORY B– AXS (T series)
 5034 PLURAL COMMAND IN G110 (T series)
 5035 NO FEEDRATE COMMANDED B–AXS (T series)
 5036 ADDRESS R NOT DEFINED IN G81–G86 (T series)
 5037 ADDRESS Q NOT DEFINED IN G83 (T series)
 5038 TOO MANY STARTM–CODE COMMAND (T series)
 5039 START UNREGISTERED B–AXS PROG (T series)
 5040 CAN NOT COMMANDED B–AXS MOVE (T series)
 5041 CAN NOT COMMANDED G110 BLOCK (T series)
 5043 TOO MANY G68 NESTING (M series)
 5044 G68 FORMAT ERROR (M series)
 5044 G68 FORMAT ERROR (T series)
 5046 ILLEGAL PARAMETER (ST.COMP)
 5050 ILL–COMMAND IN CHOPPINGMODE (M series)
 5051 M–NET CODE ERROR
 5052 M–NET ETX ERROR

 5053 M–NET CONNECT ERROR
 5054 M–NET RECEIVE ERROR
 5055 M–NET PRT/FRT ERROR
 5057 M–NET BOARD SYSTEM DOWN
 5058 G35/G36 FORMAT ERROR (T series)
 5059 RADIUS IS OUT OF RANGE
 5060 ILLEGAL PARAMETER IN G02.3/G03.3 (M series)
 5061 ILLEGAL FORMAT IN G02.3/G03.3 (M series)
 5062 ILLEGAL COMMAND IN G02.3/G03.3
 5063 IS NOT PRESET AFTER REF. (M series)
 5064 DIFFERRENT AXIS UNIT (IS– B, IS–C)
 5065 DIFFERENT AXIS UNIT (PMC AXIS) (M series)
 5067 (HPCC) (M series)
 5068 G31 FORMAT ERROR (M series)
 5069WHL–C:ILLEGAP–DATA (M series)
 5073 NO DECIMAL POINT
 5074 ADDRESS DUPLICATIONERROR
 5082 DATA SERVER ERROR
 5085 SMOOTH IPL ERROR 1
 5096 MISMATCHWAITINGM–CODE
 5110 NOT STOP POSITION
 5111 IMPROPERMODAL G–CODE (G05.1 G1) (M series)
 5112 G08 CAN NOT BE COMMANDED(G05.1 G1) (M series)
 5113 CAN NOT ERROR IN MDIMODE (Fanuc 16i/18i Model A)
 5114 NOT STOP POSITION (G05.1 Q1) (M series)
 5115 SPL : ERROR (M series)
 5122 ILLEGAL COMMAND IN SPIRAL (M series)
 5123 OVER TOLERANCE OF END POINT (M series)
 5124 CAN NOT COMMAND SPIRAL (M series)
 5134 FSSB : OPEN READY TIME OUT
 5135 FSSB : ERROR MODE
 5136 FSSB : NUMBER OF AMPS IS SMALL
 5137 FSSB : CONFIGURATIONERROR
 5138 FSSB : AXIS SETTING NOT COMPLETE
 5139 FSSB : ERROR
 5155 NOT RESTART PROGRAM BY G05
 5156 ILLEGAL AXIS OPERATION (M series)
 5157 PARAMETER ZERO (M series)
 5195 DIRECTION CAN NOT BE JUDGED (T series)
 5196 ILLEGAL OPERATION (HPCC) (M series)
 5197 FSSB : OPEN TIME OUT
 5198 FSSB : ID DATA NOT READ
 5199 FINE TORQUE SENSING PARAMETER

 5212 SCREEN COPY : PARAMETER ERROR
 5213 SCREEN COPY : COMMUNICATIONERROR
 5214 SCREEN COPY : DATA TRANSFER ERROR
 5218 ILLEGAL PARAMETER (INCL. COMP)
 5220 REFERENCE POINT ADJUSTMENTMODE
 5222 SRAM CORRECTABLE ERROR
 5227 FILE NOT FOUND
 5228 SAME NAME USED
 5229WRITE PROTECTED
 5231 TOO MANY FILES
 5232 DATA OVER– FLOW
 5235 COMMUNICATIONERROR
 5237 READ ERROR
 5238WRITE ERROR
 5242 ILLEGAL AXIS NUMBER (M series)
 5243 DATA OUT OF RANGE (M series)
 5244 TOO MANY DI ON (M series)
 5245 OTHER AXIS ARE COMMANDED (M series)
 5251 ILLEGAL PARAMETER IN G54.2 (M series)
 5252 ILLEGAL P COMMAND IN G54.2 (M series)
 5257 G41/G42 NOT ALLOWED IN MDIMODE (M series)
 5257 G41/G42 NOT ALLOWED IN MDIMODE (T series)
 5303 TOUCH PANEL ERROR
 5306 MODE CHANGE ERROR
 5307 INTERNALDATA OVER FLOW (M series)
 5400 SPL:ILLEGAL AXIS COMMAND (M series)
 5401 SPL:ILLEGAL COMMAND (M series)
 5402 SPL:ILLEGAL AXIS MOVING (M series)
 5403 SPL:CAN NOT MAKE VECTOR (M series)
 5405 ILLEGAL PARAMETER IN G41.2/ G42.2 (M series)
 5406 G41.3/G40 FORMAT ERROR (M series)
 5407 ILLEGAL COMMAND IN G41.3 (M series)
 5408 G41.3 ILLEGAL START_UP (M series)
 5409 ILLEGAL PARAMETER IN G41.3 (M series)
 5411 NURBS:ILLEGALORDER (M series)
 5412 NURBS:NO KNOT COMMAND (M series)
 5413 NURBS:ILLEGALAXIS COMMAND (M series)
 5414 NURBS:ILLEGALKNOT (M series)
 5415 NURBS:ILLEGALCANCEL (M series)
 5416 NURBS:ILLEGALMODE (M series)
 5417 NURBS:ILLEGALMULTI–KNOT (M series)
 5418 NURBS:ILLEGALKNOT VALUE (M series)
 5420 ILLEGAL PARAMETER IN G43.4/ G43.5 (M series)
 5421 ILLEGAL COMMAND IN G43.4/ G43.5 (M series)
 5422 EXCESS VELOCITY IN G43.4/ G43.5 (M series)
 5425 ILLEGAL OFFSET VALUE (M series)

 5430 ILLEGAL COMMAND IN 3–D CIR (M series)
 5432 G02.4/G03.4 FORMAT ERROR (M series)
 5433 MANUAL INTERVENTION IN 3–D CIR (M series)
 5435 PARAMETER OUT OF RANGE (TLAC) (M series)
 5436 PARAMETER SETTING ERROR 1 (TLAC) (M series)
 5437 PARAMETER SETTING ERROR 2 (TLAC) (M series)
 5440 ILLEGAL DRILLING AXIS SELECTED (M series)
 5445 CRC:MOTION IN G39 (M series)
 5446 CRC:NO AVOIDANCE (M series)
 5447 CRC:DANGEROUSAVOIDANCE (M series)
 5448 CRC:INTERFERENCETO AVD. (M series)
 5452 IMPROPER G–CODE (5AXIS MODE) (M series)
 5453 NOTE: G68 IS CANCELED (HPCC) (M series)
 5455 ILLEGAL ACC. PARAMETER (M series)
Laser alarms
Fanuc 16iL Model A
 4050 CONTOUR DATA ERROR
 4051 ASSIST GAS DATA ERR.
 4052 TRACE DATA ERROR
 4053 PIERCING DATA ERROR
 4054 E CODE DATA ERROR
 4055 E CODE NOT COMMANDED
 4056 OPT. PATH NOT SET
 4057 G25 DATA ERROR
 4058 G26 DATA ERROR
 4060 TRACE ERROR EXCESS
 4061 A/D CONVERTER–1
 4063 RF POWER SUPPLY
 4065 SHUTTER ACTION
 4066 DISCHARGING
 4067 LASER CABINET OH
 4068 BEAM REFLECTION
 4069 LASER IF PCB
 4070 CHILLER NOT READY
 4071 ASSIST GAS NOT READY
 4072 CHILL FLOW
 4073 LASER GAS PRES.
 4074 ROOTS BLOWER TEMP.
 4075 CHILL TEMP.
 4076 LASER POWER DOWN
 4077 ABSORBER TEMP.
 4078 LASER TUBE PRES.

 4079 PUSH RESET KEY
 4080 LASER TUBE EXHAUST
 4081 GAS PRES. CONTROL
 4082 TUBE PRES. SENSOR
 4083 SHUTTER NOT OPEN
 4085 MIRROR CLEANING
 4086 CALL FOR SERVICE
 4087 SHUTTER OH
 4088 LASER VOLTAGE DOWN
 4089 ASSIST GAS NO SELECT
 4090 LASER NOT GENERATE
 4091 INVERTER
 4093 BLOWER GREASE
 4094 VANE PUMP
 4096 UNDER TRACING
 4097 TRACE AXIS SELECT
 4098 TRACE AXIS & PLANE
 4099 GAS PRES. NOT REACH
 4100 INVERTER 1
 4101 OUT OF FREQUENCY 1
 4102 OUT OF VIBRATION 1
 4103 T.B NOT STOPPING 1
 4104 TURBO OVER CURRENT 1
 4105 TURBO TEMP. 1
 4106 BLOWER OIL SHORTAGE
 4107 MIRROR NOT INSTALLED
 4110 INVERTER 2
 4111 OUT OF FREQUENCY 2
 4112 OUT OF VIBRATION 2
 4113 T. B NOT STOPPING 2
 4114 TURBO OVER CURRENT 2
 4115 TURBO TEMP. 2
 4130 STEP TIME NOT SET
 4131 INCORRECT STEP DISTANCE SETTING
 4132 PARAMETERWAS CHANGED
 4136 INTERNAL PRESSURE TOO HIGH
 4137 MIXER POWER FAILURE
 4138 INSUFFICIENT DEGREE OF VACUUM
 4139 MIXER PRESSURE SWITCH ERROR
 4140 OSCILLATOR NOT READY
 4141 INITIAL LOADING
 4142 DATA RECEIVING ERROR
 4143 OVER CURRENT ERROR
 4144 DATA SENDING ERROR
 4145 TOUCH DISPLAY

 4146 POWER OVER ERROR
 4148 REG NO. NOT COMMAND
 4149 SHUTTER OPEN
Background edit alarm
BP/S alarm– BP/S alarm occurs in the same number as the P/S alarm that occurs in ordinary
program edit. (070, 071, 072, 073, 074 085,086,087 etc.)
 140 BP/S alarm
Absolute pulse coder (APC) alarms
 300 n AXIS NEED ZRN
 301 APC ALARM:n AXIS COMMUNICATION
 302 APC ALARM:n AXIS OVER TIME
 303 APC ALARM:n AXIS FRAMING
 304 APC ALARM:n AXIS PARITY
 305 APC ALARM:n AXIS PULSEMISS
 306 APC ALARM:n AXIS BATTERY ZERO
 307 APC ALARM:n AXIS BATTERY DOWN 1
 308 APC ALARM:n AXIS BATTERY DOWN 2
 309 APC ALARM:n AXIS ZRN IMPOSSIBLE
Serial pulse coder (SPC) alarms
 360 n AXIS : ABNORMALCHECKSUM (INT)
 361 n AXIS : ABNORMALPHASE DATA (INT)
 362 n AXIS : ABNORMALREV.DATA (INT)
 363 n AXIS : ABNORMALCLOCK (INT)
 364 n AXIS : SOFT PHASE ALARM (INT)
 365 n AXIS : BROKEN LED (INT)
 366 n AXIS : PULSE MISS (INT)
 367 n AXIS : COUNTMISS (INT)
 368 n AXIS : SERIAL DATA ERROR (INT)
 369 n AXIS : DATA TRANS. ERROR (INT)
 380 n AXIS : BROKEN LED (EXT)
 381 n AXIS : ABNORMALPHASE (EXT LIN)
 382 n AXIS : COUNTMISS (EXT)
 383 n AXIS : PULSE MISS (EXT)
 384 n AXIS : SOFT PHASE ALARM(EXT)
 385 n AXIS : SERIAL DATA ERROR (EXT)
 386 n AXIS : DATA TRANS. ERROR (EXT)
 387 n AXIS : ABNORMALENCODER (EXT)
Servo alarms

 400 SERVO ALARM: n–TH AXIS OVERLOAD (Fanuc 16iP Model A/B – 18iP Model
B)
 401 SERVO ALARM: n–TH AXIS VRDY OFF
 402 SERVO ALARM: SV CARD NOT EXIST
 403 SERVO ALARM: CARD/SOFTMISMATCH
 404 SERVO ALARM: n–TH AXIS VRDY ON
 405 SERVO ALARM: (ZERO POINT RETURN FAULT)
 407 SERVO ALARM: EXCESS ERROR
 409 SERVO ALARM: n AXIS TORQUE ALM
 410 SERVO ALARM: n–TH AXIS – EXCESS ERROR
 411 SERVO ALARM: n–TH AXIS – EXCESS ERROR
 413 SERVO ALARM: n–th AXIS – LSI OVERFLOW
 415 SERVO ALARM: n–TH AXIS – EXCESS SHIFT
 416 SERVO ALARM: n–TH AXIS – DISCONNECTION(Fanuc 16iP Model A/B –
18iP Model B)
 417 SERVO ALARM: n–TH AXIS – PARAMETER INCORRECT
 420 SERVO ALARM: n AXIS SYNC TORQUE (M series)
 421 SERVO ALARM: n AXIS EXCESS ER (D)
 422 SERVO ALARM: n AXIS
 423 SERVO ALARM: n AXIS
 430 n AXIS : SV. MOTOR OVERHEAT
 431 n AXIS : CNV. OVERLOAD
 432 n AXIS : CNV. LOW VOLT CONTROL
 433 n AXIS : CNV. LOW VOLT DC LINK
 434 n AXIS : INV. LOW VOLT CONTROL
 435 n AXIS : INV. LOW VOLT DC LINK
 436 n AXIS : SOFTTHERMAL (OVC)
 437 n AXIS : CNV. OVERCURRENT POWER
 438 n AXIS : INV. ABNORMALCURRENT
 439 n AXIS : CNV. OVER VOLT DC LINK
 440 n AXIS : CNV. EX DECELERATIONPOW.
 441 n AXIS : ABNORMALCURRENT OFFSET
 442 n AXIS : CNV. CHARGE FAILURE
 443 n AXIS : CNV. COOLING FAN FAILURE
 444 n AXIS : INV. COOLING FAN FAILURE
 445 n AXIS : SOFT DISCONNECT ALARM
 446 n AXIS : HARD DISCONNECT ALARM
 447 n AXIS : HARD DISCONNECT (EXT)
 448 n AXIS : UNMATCHED FEEDBACK ALARM
 449 n AXIS : INV. IPM ALARM
 453 n AXIS : SPC SOFT DISCONNECT ALARM
 460 n AXIS : FSSB DISCONNECT
 461 n AXIS : ILLEGALAMP INTERFACE
 462 n AXIS : SEND CNC DATA FAILED
 463 n AXIS : SEND SLAVE DATA FAILED
 464 n AXIS : WRITE ID DATA FAILED

 465 n AXIS : READ ID DATA FAILED
 466 n AXIS : MOTOR/AMP COMBINATION
 467 n AXIS : ILLEGAL SETTING OF AXIS
Over travel alarms
 500 OVER TRAVEL : +n
 501 OVER TRAVEL : –n
 508 INTERFERENCE: +n (T series (two–path control))
 509 INTERFERENCE: – n (T series (two–path control))
 510 OVER TRAVEL: +n
 511 OVER TRAVEL: –n
Overheat alarms
 700 OVERHEAT: CONTROLUNIT
 701 OVERHEAT: FAN MOTOR
 704 OVERHEAT: SPINDLE
Rigid tapping alarms
 740 RIGID TAP ALARM: EXCESS ERROR
 741 RIGID TAP ALARM: EXCESS ERROR
 742 RIGID TAP ALARM: LSI OVER FLOW
Serial Spindle alarms
 749 S–SPINDLE LSI ERROR
 750 SPINDLE SERIAL LINK START FAULT
 752 FIRST SPINDLEMODE CHANGE FAULT
 754 SPINDLE–1 ABNORMALTORQUE ALM
 762 SECOND SPINDLEMODE CHANGE FAULT
 772 SPINDLE–3MODE CHANGE ERROR
 782 SPINDLE–4MODE CHANGE ERROR
Safety zone alarms

 4800 ZONE : PUNCHING INHIBITED 1
 4804 ZONE : PUNCHING INHIBITED 5 (Fanuc 16iP/18iP Model B)
 4810 ZONE : ENTERING INHIBITED 1 +X
 4811 ZONE : ENTERING INHIBITED 1 –X
 4818 ZONE : ENTERING INHIBITED 5 +X (Fanuc 16iP/18iP Model B)
 4819 ZONE : ENTERING INHIBITED 5 (Fanuc 16iP/18iP Model B)
 4821 ZONE : ENTERING INHIBITED 6 (Fanuc 16iP/18iP Model B)
 4823 ZONE : ENTERING INHIBITED 7 –X (Fanuc 16iP/18iP Model B)
 4825 ZONE : ENTERING INHIBITED 8 –X (Fanuc 16iP/18iP Model B)
 4830 ZONE : ENTERING INHIBITED 1 +Y
 4831 ZONE : ENTERING INHIBITED 1 –Y
 4838 ZONE : ENTERING INHIBITED 5 +Y (Fanuc 16iP/18iP Model B)
 4839 ZONE : ENTERING INHIBITED 5 –Y (Fanuc 16iP/18iP Model B)
 4870 AUTO SETTING FEED ERROR
 4871 AUTO SETTING PIECES ERROR
 4872 AUTO SETTING COMMAND ERROR
System alarms

 900 ROM PARITY
 910 SRAM PARITY : (BYTE 0)
 911 SRAM PARITY : (BYTE 1)
 912 DRAM PARITY : (BYTE 0)
 920 SERVO ALARM(1–4 AXIS)
 921 SERVO ALARM(5–8 AXIS)
 922 SERVO ALARM(5/6 AXIS) (Fanuc 16iP Model A)
 924 SERVOMODULE SETTING ERROR (Fanuc 16iP Model A)
 926 FSSB ALARM
 930 CPU INTERRUPUT
 935 SRAM ECC ERROR
 950 PMC SYSTEM ALARM
 951 PMCWATCH DOG ALARM
 970 NMI OCCURRED IN PMCLSI
 971 NMI OCCURRED IN SLC
 972 NMI OCCURRED IN OTHER MODULE
 973 NON MASK INTERRUPT
 974 F–BUS ERROR
 975 BUS ERROR
 976 L– BUS ERROR

Fanuc 16i 18i alarms

Recommandé

Recommandé

Contenu connexe

En vedette

En vedette (10)

Similaire à Fanuc 16i 18i alarms

Similaire à Fanuc 16i 18i alarms (7)

Plus de Soekarno Revolusi

Plus de Soekarno Revolusi (17)

Dernier

Dernier (20)

Fanuc 16i 18i alarms