SlideShare une entreprise Scribd logo
1  sur  34
Télécharger pour lire hors ligne
Hydraulic control systems
Subject: Control Engineering
COMPONENTS OF HYDRAULIC
SYSTEMS:
COMPONENTS OF HYDRAULIC SYSTEMS:
•The major components are:
•Prime mover
•Pump
•Control valves
•Actuators
•Piping system
•Fluid
Few supporting components are:
• Filters
• Strainers
• Storage tank
• Heat exchangers
• Pressure gauges
• Sensors
• Protective devices
• Control devices
Major components
• Prime mover :
It is the device which
develops the mechanical
power. It is a power
producing device. The type
of prime mover will depend
on the system. After passing
through fluid power system
this power is again available
as mechanical power.
PUMP
• Hydraulic pumps are used in hydraulic drive
systems and can be hydrostatic or hydrodynamic.
• A hydraulic pump is a mechanical source of power
that converts mechanical power into hydraulic
energy (hydrostatic energy i.e. flow, pressure).
• It generates flow with enough power to overcome
pressure induced by the load at the pump outlet.
When a hydraulic pump operates, it creates a
vacuum at the pump inlet, which forces liquid from
the reservoir into the inlet line to the pump and by
mechanical action delivers this liquid to the pump
outlet and forces it into the hydraulic system.
Control valves:
• The pressurised fluid supplied by the pump is
required to diverted to various parts of the
system.
• Also controls various parameter of flowing
fluid.
• Classified into three types:
1.Pressure control valves
2.Flow control valves
3.Direction control valves
• As name suggests , these valves control the
respective parameter of fluid.
Actuators
• Actuators convert the fluid power contained
in pressurized fluid to mechanical energy.
They are the muscles of the system.
• They provide the mechanical motion to the
desired part and the desired actuating force.
• The actuators can be divided into linear and
rotary actuators.
• Example of linear actuators is single acting
cylinders and rotary actuator is limited
rotation motor.
Piping system:
• They carry fluid containing the energy to
various parts of system.
• After transmitting energy, the return oil is
brought back to the reservoir.
• Due to the high pressure involved, design of
piping system require extreme care.
• Bursting of piping could prove to be a serious
matter leading to damage of equipment or
injury to personnel.
The supporting components
Filters:
• Hydraulic filters remove dirt and particles from fluid in a
hydraulic system.
• A hydraulic filter helps to remove these particles and clean
the oil on a continuous basis. The performance for every
hydraulic filter is measured by its contamination removal
efficiency, i.e. high dirt-holding capacities. Almost every
hydraulic system contains more than one hydraulic filter.
Accumulators:
• These are storage devices. They can cater for small time
fluctuations in the energy. This may be due to power
failures. They provide a small pool of pressurized oil which
can be used during emergencies.
• Electrical devices:
• They provide much flexibility in operation.
• They are used in control of fluid power.
Electrical control enables us the remote
operation, automation and sequencing. Some
of the electrical components include
solenoids, torque motors, and limit switchers.
Pressure-control valves
• Pressure-control valves are found in virtually every
hydraulic system, and they assist in a variety of
functions, from keeping system pressures safely below
a desired upper limit to maintaining a set pressure in
part of a circuit.
• Types include relief, reducing, sequence,
counterbalance, and unloading. All of these are
normally closed valves, except for reducing valves,
which are normally open. For most of these valves, a
restriction is necessary to produce the required
pressure control. One exception is the externally
piloted unloading valve, which depends on an external
signal for its actuation
Pressure Relief valves
• Most fluid power systems are designed to
operate within a present pressure range. This
range is a function of the forces the actuators in
the system must generate to do the required
work. Without controlling or limiting these
forces, the fluid power components (and
expensive equipment) could be damaged. Relief
valves avoid this hazard. They are the safeguards
which limit maximum pressure in a system by
diverting excess oil when pressures get too high.
Flow control valves
• Flow control valves manage the flow by decreasing or
increasing the opening at the throttling point. This helps to
determine speed of movement for the actuators. The
simplest design for a flow control valve is a needle or
longitudinal slot mounted in the pipeline and connected to
a screw that adjusts the opening at the throttling point.
• These are called throttle valves and they are regularly
used in combination with a check valve, i.e. the throttle
check valve for speed control in one direction of flow. A
disadvantage of throttle valves is that at varying loads a
change in pressure drop will change the flow; thus, the
speed of the moving actuator will also be affected.
Classification of flow control valves
1. Needle valves :
Needle controls the
area of orifice , which
causes change in flow
rate through the
valve.
2. Globe valves :
Controlling element is
disc or globe.
3. Gate valves : Flow
control achieved by
the movement of the
gate.
Directional Control Valves
2 POSITION, FOUR WAY DCV
Hydraulic Integral Controller:
• This is shown in fig. the components are
similar to that of proportional control. But the
pilot valve in this case can divert the oil to two
ports. Each going to each side of a double
acting cylinder.
• The input and feedback link are the same. If an error input e is
given to input link, it moves the spool of the pilot valve. Oil
would be send to the corresponding port of the double acting
cylinder when pressurized oil goes to the double acting
cylinder.
• This movement of the piston is feedback to the feedback link.
Thus an output motion of the cylinder is produced
corresponding to the error input e.
• To show that the control action is integral. For an input
displacement e, a proportional discharge Q is produced by the
pivot valve
• Above Eel is the equation for an integral control. Thus the
above system gives a hydraulic integral control.
Derivative Controllers:
Basic definition:
• Derivative control is the type of control action in which, the
controller output is proportional to the rate of change of
the deviation.
• This mean that the controller output is related to the rate
of change of deviation.
• If the deviation is changing fast, then the controller output
will be high. If the deviation is changing at a slow rate, the
value of controller output would be low.
• The deviation control action start even before the error has
actually changed by that much. The slope of the change or
the trend is sufficient to initiate control action.
Mathematical representation:
• As per the definition, in derivative control, the
controller output m is proportional to rate of
change of error.
• Where is called the derivative time.
• If express above eel in the Laplace domain we
get,
• The block diagram will look as shown
Graphical representation
• Derivative control action is shown
graphically in fig. the error is given by
a curve as shown in the error
characteristics.
• The error increases at uniform rate,
remains constant and thereafter drops
at a constant rate.
• When error is increasing at a uniform
rate, the controller output has a
constant value as shown by the
controller characteristics. This is
because, for derivative control, the
controller output is proportional to the
rate of change of error.
• When the error curve becomes
parallel to the time axis we could see
that the controller output drops to
zero.
• So though is an error. But there is no
corrective action.
Hydraulic proportional integral
controller:
• This combines, proportional as well as integral
actions combined fig. shows the
constructional details of a hydraulic
proportional controller.
• In this, instead of a pilot valve we have a distributor
block and a swinging nozzle. The swinging nozzle is
connected to the input link. When the input link is
moved due to an input, the nozzle swings. This
changes oil flow rate through port A and B
• The swinging nozzle produces the proportional action
and the needle valve and the feedback cylinder
produces the integral action. Thus the combined
output is a proportional – integral action.
Mathematical representation:
• The three modes of control which we have seen now that is,
proportional, integral and derivative mode of control are not
always used in single mode.
• Proportional mode can be additively combined with integral
mode to get the benefits of both the modes. This is called
proportional – integral control.
• Proportional action
• Integral action
• When two are combined
• It can be represented as:
Hydraulic proportional derivative
controller:
• Given fig. shows the schematic diagram of a proportional derivative controller.
It consists of an input arm to which the input displacement x is given.
• Pilot cylinder has five ports. Pressurized oil comes to the pilot cylinder
through the center port. Return oil goes through the two end ports. Oil goes to
the two sides of the power cylinder depending up on the position of the spools.
The spool has two pistons connected to the common rod. Depending on the
input displacement and the error signal, the spools move to the right or left.
• The power cylinder has one piston connected to the piston rod.
Depending up on the oil flowing in to the power cylinder the piston will move in
appropriate direction. This will give the output displacement y to the piston rod.
• Working:
• When an input displacement is given to the input lever say to
the right the spool move to the right. This will cause the oil to
flow to the left side of the power cylinder. This will push the
piston to right by an amount y. the amount of piton
movement will be proportional to the input displacement x.
This is the proportional part of the controller.
• Simultaneously the rod of the power cylinder will move the
piston in the feedback cylinder. The movement of the piston
in the feedback cylinder will push the fluid to the right
pressurizing the fluid in the right side of the cylinder. This in
turn will cause a flow rate of oil from the right side to the left
side. This is nothing but a rate feedback.
• Graphical representation:
• A proportional –derivative
action cannot be adequately
described by a step change.
Because as we saw earlier, in
pure derivative the controller
output is present only during
the rising part of the step.
• There after the output drops to
zero at the flat portion of the
step. So we will use a ramp
signal as the error input and see
how the output would be
shown in fig.
• For a ramp signal
• Block diagram I s shown in fig.
Proportional – Integral – Derivative
Control (PID):
• This is also called the three mode control. It
combines the merits of all the three modes and is
widely used in processes. It is commonly known as
PID Control.
• It is nothing but the additive combination of
proportional, integral, and derivative control actions.
• mathematically a PID control action is
represented as
• In Laplace form,
•
Comparison of Electricl and Hydraulik
Systems
Hydraulic control system (ce ppt)
THANKYOU!

Contenu connexe

Tendances

Module 5 hydraulics and pneumatics Actuation systems
Module 5 hydraulics and pneumatics Actuation systemsModule 5 hydraulics and pneumatics Actuation systems
Module 5 hydraulics and pneumatics Actuation systemstaruian
 
Hydraulic Valves (Valves) (Pneumatics also)
Hydraulic Valves (Valves) (Pneumatics also)Hydraulic Valves (Valves) (Pneumatics also)
Hydraulic Valves (Valves) (Pneumatics also)Mohammad Azam Khan
 
Pneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRL
Pneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRLPneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRL
Pneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRLAbhishek Patange
 
Fundamental of hydraulic components
Fundamental of hydraulic componentsFundamental of hydraulic components
Fundamental of hydraulic componentsPrasadroshan Mythin
 
Hydraulic control system
Hydraulic control systemHydraulic control system
Hydraulic control systemDhavalkumar R
 
What Is Hydraulic Filter?
What Is Hydraulic Filter?What Is Hydraulic Filter?
What Is Hydraulic Filter?payalkataria01
 
Hydraulic Valves and Hydraulic System Accessories
Hydraulic Valves and Hydraulic System AccessoriesHydraulic Valves and Hydraulic System Accessories
Hydraulic Valves and Hydraulic System AccessoriesRAHUL THAKER
 
Concepts of Pneumatic System.pdf
Concepts of Pneumatic System.pdfConcepts of Pneumatic System.pdf
Concepts of Pneumatic System.pdfRuzaanKaranjia
 
HYDRAULICS AND PNEUMATICS (UNIT 4)
HYDRAULICS AND PNEUMATICS   (UNIT 4)HYDRAULICS AND PNEUMATICS   (UNIT 4)
HYDRAULICS AND PNEUMATICS (UNIT 4)kannanmuthu11
 
Pneumatics and hydraulics ppt
Pneumatics and hydraulics pptPneumatics and hydraulics ppt
Pneumatics and hydraulics pptwifi0047
 
Components of hydraulic & pneumetic
Components of hydraulic & pneumeticComponents of hydraulic & pneumetic
Components of hydraulic & pneumeticShivji Dangar
 

Tendances (20)

Shuttle valve
Shuttle valveShuttle valve
Shuttle valve
 
Module 5 hydraulics and pneumatics Actuation systems
Module 5 hydraulics and pneumatics Actuation systemsModule 5 hydraulics and pneumatics Actuation systems
Module 5 hydraulics and pneumatics Actuation systems
 
Hydraulic Valves (Valves) (Pneumatics also)
Hydraulic Valves (Valves) (Pneumatics also)Hydraulic Valves (Valves) (Pneumatics also)
Hydraulic Valves (Valves) (Pneumatics also)
 
Hydraulic system
Hydraulic systemHydraulic system
Hydraulic system
 
Pneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRL
Pneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRLPneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRL
Pneumatics: Shuttle, Twin pressure, Quick Exhaust, Time Delay, FRL
 
Hidraulic Symbols
Hidraulic Symbols Hidraulic Symbols
Hidraulic Symbols
 
Fundamental of hydraulic components
Fundamental of hydraulic componentsFundamental of hydraulic components
Fundamental of hydraulic components
 
Hydraulic control system
Hydraulic control systemHydraulic control system
Hydraulic control system
 
What Is Hydraulic Filter?
What Is Hydraulic Filter?What Is Hydraulic Filter?
What Is Hydraulic Filter?
 
Hydraulic system
Hydraulic systemHydraulic system
Hydraulic system
 
Hydraulic Valves and Hydraulic System Accessories
Hydraulic Valves and Hydraulic System AccessoriesHydraulic Valves and Hydraulic System Accessories
Hydraulic Valves and Hydraulic System Accessories
 
Concepts of Pneumatic System.pdf
Concepts of Pneumatic System.pdfConcepts of Pneumatic System.pdf
Concepts of Pneumatic System.pdf
 
Pneumatic systems
Pneumatic systemsPneumatic systems
Pneumatic systems
 
Hydraulic circuits
Hydraulic circuitsHydraulic circuits
Hydraulic circuits
 
Maintenance of Hydraulic Systems
Maintenance of Hydraulic SystemsMaintenance of Hydraulic Systems
Maintenance of Hydraulic Systems
 
Hydraulic pumps performance and Characteristics
Hydraulic pumps performance and CharacteristicsHydraulic pumps performance and Characteristics
Hydraulic pumps performance and Characteristics
 
HYDRAULICS AND PNEUMATICS (UNIT 4)
HYDRAULICS AND PNEUMATICS   (UNIT 4)HYDRAULICS AND PNEUMATICS   (UNIT 4)
HYDRAULICS AND PNEUMATICS (UNIT 4)
 
Pneumatics and hydraulics ppt
Pneumatics and hydraulics pptPneumatics and hydraulics ppt
Pneumatics and hydraulics ppt
 
Hydraulic control system
Hydraulic control systemHydraulic control system
Hydraulic control system
 
Components of hydraulic & pneumetic
Components of hydraulic & pneumeticComponents of hydraulic & pneumetic
Components of hydraulic & pneumetic
 

Similaire à Hydraulic control system (ce ppt)

Ce.pptx 2
Ce.pptx 2Ce.pptx 2
Ce.pptx 2Hrdbs
 
Basic hydraulics
Basic hydraulicsBasic hydraulics
Basic hydraulicsPINAKI ROY
 
Hydraulic Contol System
Hydraulic Contol SystemHydraulic Contol System
Hydraulic Contol SystemHimanshi Gupta
 
HYDRAULIC AND PNEUMATIC ACTUATOR
HYDRAULIC AND PNEUMATIC ACTUATORHYDRAULIC AND PNEUMATIC ACTUATOR
HYDRAULIC AND PNEUMATIC ACTUATORKANA RAM MEENA
 
Chapter_4_HYDRAULIC final ppt presentation
Chapter_4_HYDRAULIC final ppt presentationChapter_4_HYDRAULIC final ppt presentation
Chapter_4_HYDRAULIC final ppt presentationsrajece
 
2 c industrial hydraulic circuits
2 c industrial hydraulic circuits2 c industrial hydraulic circuits
2 c industrial hydraulic circuitsDr.R. SELVAM
 
pressurecontrolvalves-161017051912.pptx
pressurecontrolvalves-161017051912.pptxpressurecontrolvalves-161017051912.pptx
pressurecontrolvalves-161017051912.pptxPrathapS46
 
application of Direction control valve in automatic transmission
application of Direction control valve in automatic transmissionapplication of Direction control valve in automatic transmission
application of Direction control valve in automatic transmissionZIYAD AMBALANGADAN
 
Centrifugal Pumps and Compressor.pdf [Autosaved].pptx
Centrifugal Pumps and Compressor.pdf [Autosaved].pptxCentrifugal Pumps and Compressor.pdf [Autosaved].pptx
Centrifugal Pumps and Compressor.pdf [Autosaved].pptxFahadReda2
 
2 hydraulic motor and control component
2 hydraulic motor and control component2 hydraulic motor and control component
2 hydraulic motor and control componentDr.R. SELVAM
 
Week 2 2_hydraulic_systems_component
Week 2 2_hydraulic_systems_componentWeek 2 2_hydraulic_systems_component
Week 2 2_hydraulic_systems_componentakmal ariffin
 
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdfcbecuk23
 
ROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORSROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORSTAMILMECHKIT
 
3 valve shafts pneumatics and hydraulics
3 valve shafts pneumatics and hydraulics3 valve shafts pneumatics and hydraulics
3 valve shafts pneumatics and hydraulicsaman520305
 
vinay kumar actuators report
vinay kumar   actuators reportvinay kumar   actuators report
vinay kumar actuators reportAkash Maurya
 
EMERGENCY BRAKING SYSTEM.pptx
EMERGENCY BRAKING SYSTEM.pptxEMERGENCY BRAKING SYSTEM.pptx
EMERGENCY BRAKING SYSTEM.pptxGokul740367
 

Similaire à Hydraulic control system (ce ppt) (20)

Ce.pptx 2
Ce.pptx 2Ce.pptx 2
Ce.pptx 2
 
MEKATRONIKA Aktuator.pptx
MEKATRONIKA Aktuator.pptxMEKATRONIKA Aktuator.pptx
MEKATRONIKA Aktuator.pptx
 
DOC-20240201-WA0004..pdf
DOC-20240201-WA0004..pdfDOC-20240201-WA0004..pdf
DOC-20240201-WA0004..pdf
 
Basic hydraulics
Basic hydraulicsBasic hydraulics
Basic hydraulics
 
Hydraulic Contol System
Hydraulic Contol SystemHydraulic Contol System
Hydraulic Contol System
 
HYDRAULIC AND PNEUMATIC ACTUATOR
HYDRAULIC AND PNEUMATIC ACTUATORHYDRAULIC AND PNEUMATIC ACTUATOR
HYDRAULIC AND PNEUMATIC ACTUATOR
 
Chapter_4_HYDRAULIC final ppt presentation
Chapter_4_HYDRAULIC final ppt presentationChapter_4_HYDRAULIC final ppt presentation
Chapter_4_HYDRAULIC final ppt presentation
 
Hydraulic systems report
Hydraulic systems  reportHydraulic systems  report
Hydraulic systems report
 
2 c industrial hydraulic circuits
2 c industrial hydraulic circuits2 c industrial hydraulic circuits
2 c industrial hydraulic circuits
 
pressurecontrolvalves-161017051912.pptx
pressurecontrolvalves-161017051912.pptxpressurecontrolvalves-161017051912.pptx
pressurecontrolvalves-161017051912.pptx
 
application of Direction control valve in automatic transmission
application of Direction control valve in automatic transmissionapplication of Direction control valve in automatic transmission
application of Direction control valve in automatic transmission
 
Centrifugal Pumps and Compressor.pdf [Autosaved].pptx
Centrifugal Pumps and Compressor.pdf [Autosaved].pptxCentrifugal Pumps and Compressor.pdf [Autosaved].pptx
Centrifugal Pumps and Compressor.pdf [Autosaved].pptx
 
2 hydraulic motor and control component
2 hydraulic motor and control component2 hydraulic motor and control component
2 hydraulic motor and control component
 
Week 2 2_hydraulic_systems_component
Week 2 2_hydraulic_systems_componentWeek 2 2_hydraulic_systems_component
Week 2 2_hydraulic_systems_component
 
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
53_36765_ME594_2014_1__2_1_Robot Actuators.pdf
 
ROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORSROBOT DRIVE SYSTEMS AND END EFFECTORS
ROBOT DRIVE SYSTEMS AND END EFFECTORS
 
3 valve shafts pneumatics and hydraulics
3 valve shafts pneumatics and hydraulics3 valve shafts pneumatics and hydraulics
3 valve shafts pneumatics and hydraulics
 
vinay kumar actuators report
vinay kumar   actuators reportvinay kumar   actuators report
vinay kumar actuators report
 
8.Hydraulic system.pptx
8.Hydraulic system.pptx8.Hydraulic system.pptx
8.Hydraulic system.pptx
 
EMERGENCY BRAKING SYSTEM.pptx
EMERGENCY BRAKING SYSTEM.pptxEMERGENCY BRAKING SYSTEM.pptx
EMERGENCY BRAKING SYSTEM.pptx
 

Plus de Deep Chaudhari

Plus de Deep Chaudhari (7)

ELECTROSTATIC INDUCTION AND GAUSS LAW
ELECTROSTATIC INDUCTION AND GAUSS LAWELECTROSTATIC INDUCTION AND GAUSS LAW
ELECTROSTATIC INDUCTION AND GAUSS LAW
 
TYPES OF BRAKE
TYPES OF BRAKETYPES OF BRAKE
TYPES OF BRAKE
 
IMPULSE TURBINE
IMPULSE TURBINEIMPULSE TURBINE
IMPULSE TURBINE
 
Hydraulic control system (ce ppt)
Hydraulic control system (ce ppt)Hydraulic control system (ce ppt)
Hydraulic control system (ce ppt)
 
BELL DRIVES
BELL DRIVESBELL DRIVES
BELL DRIVES
 
TIME RESPONSE ANALYSIS
TIME RESPONSE ANALYSISTIME RESPONSE ANALYSIS
TIME RESPONSE ANALYSIS
 
EDDY CURRENT TESTING
EDDY CURRENT TESTINGEDDY CURRENT TESTING
EDDY CURRENT TESTING
 

Dernier

Patents and AI: Current Tools, Future Solutions
Patents and AI: Current Tools, Future SolutionsPatents and AI: Current Tools, Future Solutions
Patents and AI: Current Tools, Future SolutionsAurora Consulting
 
An introduction to Indian Contract Act, 1872 by Shraddha Pandit
An introduction to Indian Contract Act, 1872 by Shraddha PanditAn introduction to Indian Contract Act, 1872 by Shraddha Pandit
An introduction to Indian Contract Act, 1872 by Shraddha PanditSHRADDHA PANDIT
 
state responsibility IN INTERNATIOAL LAW.pptx
state responsibility IN INTERNATIOAL LAW.pptxstate responsibility IN INTERNATIOAL LAW.pptx
state responsibility IN INTERNATIOAL LAW.pptxadvpraballb
 
xLran: Open source AI for legal hackers.
xLran: Open source AI for legal hackers.xLran: Open source AI for legal hackers.
xLran: Open source AI for legal hackers.mike689707
 
The Ultimate Guide to Drafting Your Separation Agreement with a Template
The Ultimate Guide to Drafting Your Separation Agreement with a TemplateThe Ultimate Guide to Drafting Your Separation Agreement with a Template
The Ultimate Guide to Drafting Your Separation Agreement with a TemplateBTL Law P.C.
 
Classification of Contracts in Business Regulations
Classification of Contracts in Business RegulationsClassification of Contracts in Business Regulations
Classification of Contracts in Business RegulationsSyedaAyeshaTabassum1
 
The Dharmasastra and Modern Law in India.pptx
The Dharmasastra and Modern Law in India.pptxThe Dharmasastra and Modern Law in India.pptx
The Dharmasastra and Modern Law in India.pptxsunilsondhi5
 
Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...
Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...
Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...SHRADDHA PANDIT
 
Understanding Cryptocurrency Regulation in India: 2024
Understanding Cryptocurrency Regulation in India: 2024Understanding Cryptocurrency Regulation in India: 2024
Understanding Cryptocurrency Regulation in India: 2024Finlaw Consultancy Pvt Ltd
 
Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...
Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...
Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...Dr. Oliver Massmann
 

Dernier (12)

Patents and AI: Current Tools, Future Solutions
Patents and AI: Current Tools, Future SolutionsPatents and AI: Current Tools, Future Solutions
Patents and AI: Current Tools, Future Solutions
 
An introduction to Indian Contract Act, 1872 by Shraddha Pandit
An introduction to Indian Contract Act, 1872 by Shraddha PanditAn introduction to Indian Contract Act, 1872 by Shraddha Pandit
An introduction to Indian Contract Act, 1872 by Shraddha Pandit
 
state responsibility IN INTERNATIOAL LAW.pptx
state responsibility IN INTERNATIOAL LAW.pptxstate responsibility IN INTERNATIOAL LAW.pptx
state responsibility IN INTERNATIOAL LAW.pptx
 
xLran: Open source AI for legal hackers.
xLran: Open source AI for legal hackers.xLran: Open source AI for legal hackers.
xLran: Open source AI for legal hackers.
 
The Ultimate Guide to Drafting Your Separation Agreement with a Template
The Ultimate Guide to Drafting Your Separation Agreement with a TemplateThe Ultimate Guide to Drafting Your Separation Agreement with a Template
The Ultimate Guide to Drafting Your Separation Agreement with a Template
 
Classification of Contracts in Business Regulations
Classification of Contracts in Business RegulationsClassification of Contracts in Business Regulations
Classification of Contracts in Business Regulations
 
The Dharmasastra and Modern Law in India.pptx
The Dharmasastra and Modern Law in India.pptxThe Dharmasastra and Modern Law in India.pptx
The Dharmasastra and Modern Law in India.pptx
 
Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...
Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...
Women and the World of Climate Change- A Conceptual Foundation by Shraddha Pa...
 
Understanding Cryptocurrency Regulation in India: 2024
Understanding Cryptocurrency Regulation in India: 2024Understanding Cryptocurrency Regulation in India: 2024
Understanding Cryptocurrency Regulation in India: 2024
 
Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...
Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...
Corporate Sustainability Due Diligence Directive (CSDDD or the EU Supply Chai...
 
Criminalizing Disabilities & False Confessions
Criminalizing Disabilities & False ConfessionsCriminalizing Disabilities & False Confessions
Criminalizing Disabilities & False Confessions
 
Biography, Headshot and Vita Fee Document
Biography, Headshot and Vita Fee DocumentBiography, Headshot and Vita Fee Document
Biography, Headshot and Vita Fee Document
 

Hydraulic control system (ce ppt)

  • 2. COMPONENTS OF HYDRAULIC SYSTEMS: COMPONENTS OF HYDRAULIC SYSTEMS: •The major components are: •Prime mover •Pump •Control valves •Actuators •Piping system •Fluid
  • 3. Few supporting components are: • Filters • Strainers • Storage tank • Heat exchangers • Pressure gauges • Sensors • Protective devices • Control devices
  • 4. Major components • Prime mover : It is the device which develops the mechanical power. It is a power producing device. The type of prime mover will depend on the system. After passing through fluid power system this power is again available as mechanical power.
  • 5. PUMP • Hydraulic pumps are used in hydraulic drive systems and can be hydrostatic or hydrodynamic. • A hydraulic pump is a mechanical source of power that converts mechanical power into hydraulic energy (hydrostatic energy i.e. flow, pressure). • It generates flow with enough power to overcome pressure induced by the load at the pump outlet. When a hydraulic pump operates, it creates a vacuum at the pump inlet, which forces liquid from the reservoir into the inlet line to the pump and by mechanical action delivers this liquid to the pump outlet and forces it into the hydraulic system.
  • 6. Control valves: • The pressurised fluid supplied by the pump is required to diverted to various parts of the system. • Also controls various parameter of flowing fluid. • Classified into three types: 1.Pressure control valves 2.Flow control valves 3.Direction control valves • As name suggests , these valves control the respective parameter of fluid.
  • 7. Actuators • Actuators convert the fluid power contained in pressurized fluid to mechanical energy. They are the muscles of the system. • They provide the mechanical motion to the desired part and the desired actuating force. • The actuators can be divided into linear and rotary actuators. • Example of linear actuators is single acting cylinders and rotary actuator is limited rotation motor.
  • 8. Piping system: • They carry fluid containing the energy to various parts of system. • After transmitting energy, the return oil is brought back to the reservoir. • Due to the high pressure involved, design of piping system require extreme care. • Bursting of piping could prove to be a serious matter leading to damage of equipment or injury to personnel.
  • 9. The supporting components Filters: • Hydraulic filters remove dirt and particles from fluid in a hydraulic system. • A hydraulic filter helps to remove these particles and clean the oil on a continuous basis. The performance for every hydraulic filter is measured by its contamination removal efficiency, i.e. high dirt-holding capacities. Almost every hydraulic system contains more than one hydraulic filter. Accumulators: • These are storage devices. They can cater for small time fluctuations in the energy. This may be due to power failures. They provide a small pool of pressurized oil which can be used during emergencies.
  • 10. • Electrical devices: • They provide much flexibility in operation. • They are used in control of fluid power. Electrical control enables us the remote operation, automation and sequencing. Some of the electrical components include solenoids, torque motors, and limit switchers.
  • 11. Pressure-control valves • Pressure-control valves are found in virtually every hydraulic system, and they assist in a variety of functions, from keeping system pressures safely below a desired upper limit to maintaining a set pressure in part of a circuit. • Types include relief, reducing, sequence, counterbalance, and unloading. All of these are normally closed valves, except for reducing valves, which are normally open. For most of these valves, a restriction is necessary to produce the required pressure control. One exception is the externally piloted unloading valve, which depends on an external signal for its actuation
  • 12. Pressure Relief valves • Most fluid power systems are designed to operate within a present pressure range. This range is a function of the forces the actuators in the system must generate to do the required work. Without controlling or limiting these forces, the fluid power components (and expensive equipment) could be damaged. Relief valves avoid this hazard. They are the safeguards which limit maximum pressure in a system by diverting excess oil when pressures get too high.
  • 13. Flow control valves • Flow control valves manage the flow by decreasing or increasing the opening at the throttling point. This helps to determine speed of movement for the actuators. The simplest design for a flow control valve is a needle or longitudinal slot mounted in the pipeline and connected to a screw that adjusts the opening at the throttling point. • These are called throttle valves and they are regularly used in combination with a check valve, i.e. the throttle check valve for speed control in one direction of flow. A disadvantage of throttle valves is that at varying loads a change in pressure drop will change the flow; thus, the speed of the moving actuator will also be affected.
  • 14. Classification of flow control valves 1. Needle valves : Needle controls the area of orifice , which causes change in flow rate through the valve. 2. Globe valves : Controlling element is disc or globe. 3. Gate valves : Flow control achieved by the movement of the gate.
  • 15. Directional Control Valves 2 POSITION, FOUR WAY DCV
  • 16. Hydraulic Integral Controller: • This is shown in fig. the components are similar to that of proportional control. But the pilot valve in this case can divert the oil to two ports. Each going to each side of a double acting cylinder.
  • 17. • The input and feedback link are the same. If an error input e is given to input link, it moves the spool of the pilot valve. Oil would be send to the corresponding port of the double acting cylinder when pressurized oil goes to the double acting cylinder. • This movement of the piston is feedback to the feedback link. Thus an output motion of the cylinder is produced corresponding to the error input e. • To show that the control action is integral. For an input displacement e, a proportional discharge Q is produced by the pivot valve • Above Eel is the equation for an integral control. Thus the above system gives a hydraulic integral control.
  • 18. Derivative Controllers: Basic definition: • Derivative control is the type of control action in which, the controller output is proportional to the rate of change of the deviation. • This mean that the controller output is related to the rate of change of deviation. • If the deviation is changing fast, then the controller output will be high. If the deviation is changing at a slow rate, the value of controller output would be low. • The deviation control action start even before the error has actually changed by that much. The slope of the change or the trend is sufficient to initiate control action.
  • 19. Mathematical representation: • As per the definition, in derivative control, the controller output m is proportional to rate of change of error. • Where is called the derivative time. • If express above eel in the Laplace domain we get,
  • 20. • The block diagram will look as shown
  • 21. Graphical representation • Derivative control action is shown graphically in fig. the error is given by a curve as shown in the error characteristics. • The error increases at uniform rate, remains constant and thereafter drops at a constant rate. • When error is increasing at a uniform rate, the controller output has a constant value as shown by the controller characteristics. This is because, for derivative control, the controller output is proportional to the rate of change of error. • When the error curve becomes parallel to the time axis we could see that the controller output drops to zero. • So though is an error. But there is no corrective action.
  • 22. Hydraulic proportional integral controller: • This combines, proportional as well as integral actions combined fig. shows the constructional details of a hydraulic proportional controller.
  • 23. • In this, instead of a pilot valve we have a distributor block and a swinging nozzle. The swinging nozzle is connected to the input link. When the input link is moved due to an input, the nozzle swings. This changes oil flow rate through port A and B • The swinging nozzle produces the proportional action and the needle valve and the feedback cylinder produces the integral action. Thus the combined output is a proportional – integral action.
  • 24. Mathematical representation: • The three modes of control which we have seen now that is, proportional, integral and derivative mode of control are not always used in single mode. • Proportional mode can be additively combined with integral mode to get the benefits of both the modes. This is called proportional – integral control. • Proportional action • Integral action
  • 25. • When two are combined • It can be represented as:
  • 26. Hydraulic proportional derivative controller: • Given fig. shows the schematic diagram of a proportional derivative controller. It consists of an input arm to which the input displacement x is given. • Pilot cylinder has five ports. Pressurized oil comes to the pilot cylinder through the center port. Return oil goes through the two end ports. Oil goes to the two sides of the power cylinder depending up on the position of the spools. The spool has two pistons connected to the common rod. Depending on the input displacement and the error signal, the spools move to the right or left. • The power cylinder has one piston connected to the piston rod. Depending up on the oil flowing in to the power cylinder the piston will move in appropriate direction. This will give the output displacement y to the piston rod.
  • 27. • Working: • When an input displacement is given to the input lever say to the right the spool move to the right. This will cause the oil to flow to the left side of the power cylinder. This will push the piston to right by an amount y. the amount of piton movement will be proportional to the input displacement x. This is the proportional part of the controller. • Simultaneously the rod of the power cylinder will move the piston in the feedback cylinder. The movement of the piston in the feedback cylinder will push the fluid to the right pressurizing the fluid in the right side of the cylinder. This in turn will cause a flow rate of oil from the right side to the left side. This is nothing but a rate feedback.
  • 28. • Graphical representation: • A proportional –derivative action cannot be adequately described by a step change. Because as we saw earlier, in pure derivative the controller output is present only during the rising part of the step. • There after the output drops to zero at the flat portion of the step. So we will use a ramp signal as the error input and see how the output would be shown in fig. • For a ramp signal
  • 29. • Block diagram I s shown in fig.
  • 30. Proportional – Integral – Derivative Control (PID): • This is also called the three mode control. It combines the merits of all the three modes and is widely used in processes. It is commonly known as PID Control. • It is nothing but the additive combination of proportional, integral, and derivative control actions.
  • 31. • mathematically a PID control action is represented as • In Laplace form, •
  • 32. Comparison of Electricl and Hydraulik Systems