This manual provides service procedures for the TOYOTA FORKLIFT 5FG10-30/5FD70-30 Series from August 1986 to August 1989. It covers models with 4P, 4Y, 2J, 1Z, and 7DZ gasoline and diesel engines. The manual includes exterior views of the vehicles, listings of vehicle models and specifications, standard bolt tightening torques, maintenance schedules, and references to separate engine repair manuals. Minor changes were made to the models in September 1986 and September 1989, which are addressed.

1. FOREWORD
This manual covers the service procedures of the TOYOTA FORKLIFT 5FGIO-
30/5FD70-30 Series. Please use this manual for providing quick, correct
servicing of the corresponding forklift models.
These models on the market since August 7986 are subject to minor changes
in September 7986. This manual deals with the models produced in the period
between A ugust 7988 and August 7989 as well as the models as of September
7989 (after m~nor
changes}.
Any change or modifications thereafter will be informed by Toyota Industrial
Vehicles' Parts & Service News.
For the service procedures of the mounted engine, read the repair manuals
listed below as reference together with this manual.
(Reference)
Repair manuals related to this manual are as follows:
TOY0TA INDUSTRIAL VEHICLE 4P ENGINE
REPAIR MANUAL (No. CE604)
TOYOTA INDUSTRIAL VEHICLE 4Y ENGINE
REPAIR MANUAL (No. CE602)
TOYOTA INDUSTRIAL VEHICLE 2J ENGINE
REPAIR MANUAL (No. CE603)
TOYOTA INDUSTRIAL VEHICLE 7ZENGINE
REPAIR MANUAL (No. CE60 7)
TOYOTA INDUSTRIAL VEHICLE 5K ENGINE
REPAIR MANUAL (No. CE67 7)
TOYOTA INDUSTRIAL VEHICLE 7DZ ENGINE
REPAIR MANUAL (No. CE6 18)
(Note: 2-3 ton models mounted with 2J, IDZ diesel engine are only available
in designated areas.)
TOYOTA MOTOR CORPORATION

3. GENERAL
Page
..............................
EXTERIOR VIEWS 0-2
VEHICLE LISTING .............................. 0-3
ABBREVIATIONS................................ 0-7
.............................
OPERATIONAL TIPS 0-7
STANDARD BOLT & NUT TIGHTENING
TORQUE ..................................... 0-8
HIGH PRESSURE HOSE FITTING
........................
TIGHTENING TORQUE 0-10
FRAME NUMBER ............................... 0-11
WIRE ROPE SUSPENSION ANGLE LIST ............ 0-14
SAFE LOAD FOR EACH WlRE ROPE
SUSPENSION ANGLE .......................... 0-14
COMPONENT WEIGHT ........................... 0-15
RECOMMENDED LUBRICANT QUANTITY
& TYPE ...................................... 0-17
LUBRICATION CHARTS .......................... 0-21
.......................
PERIODIC MAINTENANCE 0-22
PERIODIC REPLACEMENT LUBRICANTS
..................................
AND PARTS 0-29

4. EXTERIOR VIEWS
Front View (5FG15) LATI4-16
Rear View (5FG15) LAT14-18

5. VEHICLE LISTING (1986.8-1989.8)
Se-
ries
%
.-
L
%
C
0
+
-
V)
Q
,
.-
L
%
0
+
CU
Payload
1.0 ton
1.35 ton
1.5 ton
1.75 ton
2.0ton
Model
5FG10
02- 5FG10
40- 5FG10
42- 5FG10
5FD10
02 - 5FD10
5FG14
02- 5FG14
40- 5FG14
42- 5FG14
5FD14
02- 5FD14
5FG15
02- 5FG15
40- 5FG15
42- 5FG15
5FD15
02- 5FD15
5FG18
02- 5FG18
40- 5FG18
42- 5FG18
5FD18
02- 5FD18
5FG20
02- 5FG20
40- 5FG20
42- 5FG20
5FD20
02- 5FD20
60 - 5FD20
62 - 5FD20
Engine
model
4 P
?
4 Y
f
2 J
f
4 P
f
4 Y
f
2 J
t
4 P
f
4 Y
f
2 J
t
4 P
f
4 Y
t
2 J
f
4 P
t
4 Y
t
1 Z
f
2 J
f
Engine
tYPe
Gasoline
f
f
f
D~esel
T
Gasoline
f
7'
t
Diesel
.f
Gasoline
t
f
t
Diesel
t
Gasoline
?
f
f
Diesel
t
Gasoline
t
t
t
Diesel
t
f
f
Drive system
11" clutch
Torque converter
11" clutch
Torque converter
11 " clutch
Torque converter
I1" clutch
Torque converter
11 " clutch
Torque converter
1 1" clutch
Torque converter
I 1" clutch
Torque converter
I 1" clutch
Torque converter
I I"clutch
Torque converter
11" clutch
Torque converter
1I" clutch
Torque converter
11" clutch
Torque converter
1 1" clutch
Torque converter
11" clutch
Torque converter
11" clutch
Torque converter
11" clutch
Torque converter
Remarks
P/S installed
as standard
f
f
t
f
t
f
f
7.
f
f
t
f
t
t
f
f
f
f
f
t
t
f
f
t
I.
t
7-
f
f
t
f

7. VEHICLE LISTING (1989.9 -
Ser~es
1 ton serles
2 ton series
Engine model
5K
4Y
1DZ
5K
4Y
1DZ
5K
4Y
1DZ
5K
4Y
1DZ
5K
4Y
1z
1 DZ
5K
4Y
Dr~ve
system
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Load capac~ty
1.0 ton
1.35 ton
1.5 ton
1.75 ton
2.0 ton
2.25 ton
Model
5FG10
02-5FG10
40-5FG10
42-5FG10
5FD10
02-5FD10
5FG14
02-5FG14
40-5FG14
42-5FG14
5FD14
02-5FD14
5FG15
02-5FG15
40-5FG15
42-5FG15
5FD15
02-5FD15
5FG18
02-5FG18
40-5FG18
42-5FG18
5FD18
02-5FD18
5FG20
02-5FG20
40-5FG20
42-5FG20
5FD20
02-5FD20
60-5FD20
62-5FD20
5FG23
02-5FG23
40-5FG23
42-5FG23

8. Series
2 ton series
Load capacity
2.25 ton
2.5 ton
Model
5FD23
02-5FD23
60-5FD23
62-5FD23
5FG25
02-5FG25
40-5FG25
42-5FG25
5FD25
02-5FD25
60-5FD25
62-5FD25
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
4Y
3 ton series
Engine model
1z
1DZ
5K
4Y
1z
1DZ
Drive system
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
Clutch
Torque converter
2.75 ton
3.0 ton
5FD28
02-5FD28
60-5FD28
62-5FD28
5FG30
02-5FG30
5FD30
02-5FD30
60-5FD30
62-5FD30
1Z
1DZ
4Y
1Z
1DZ

9. ABBREVIATIONS
Abbreviations used in this manual are as follows:
OPERATIONAL TIPS
1. Safe operation
( 1 ) Make sure that correct size wire is used for hoisting a heavy material
(2)After jacking up, always support with rigid racks or stands.
Meaning
Power Steering
Right Hand
Society of Automotive Engineers
(USA)
Special Service Tool
Standard
Sub-assembly
Tightening Torque
Number of Teeth (00)
Undersize
With
Abbreviation
(Code)
ABDC
ASSY
ATDC
ATM
BBDC
LH
LLC
MTM
OHV
0PT
0/S
PS
2. Preparation of SSTs and measuring tools
( 1 ) Prepare SSTs and measuring tools before starting operation.
3. Clearing and arrangement
( 1) Always keep the workshop neat and orderly for easy operation.
(2)Disassembly of hydraulic equipment shall always be done in a clean place using clean tools.
Meaning
After Bottom Dead Center
Assembly
After Top Dead Center
Automatic Transmission
Before Bottom Dead Center
Left Hand
Long Life Coolant
Manual Transmission
Overhead valve
Option
Oversi~e
Horsepower
4. Genuine Toyota parts
Genuine Toyota parts should be used even in the replacement of packings, gaskets and O-rings.
Abbreviation
(Code)
P/S
RH
SAE
SST
STD
SUB-ASSY
T =
OOT
U/S
w/
5. Repairs on electrical system
Before doing any repairs on the electrical system, disconnect the cables from the battery terminals.
Be sure to disconnect the negative @ cable first.
6. Tightening torque for irlstallation
Be sure to observe the tightening torque given in this manual. If not specified, tighten to the torque '
listed in standard bolt & nut tightening torque.
7. Defect status grasp
Do not start disassernbly and replacement as soon as a defect is found, but first grasp whether the
defect requires disassembly and replacement. In the case of torque converter for example, do not
attempt torque converter disassembly upon a failure in starting the vehicle, but first check such
factors as the oil, pressure and rotation status causing the failure.

10. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

11. STANDARD BOLT AND NUT TIGHTENING TORQUES
How to judge tightening torque of a standard bolt or nut.
1. How to judge tightening torque of a standard bolt.
Find out the type of the bolt from the list below.
Then, find the bolt tightening torque from the table.
2. How to judge tighting torque of a standard unit.
The nut tightening torque can be judged from the bolt type. (See the item above.)
LIST OF BOLT TYPES AND STRENGTH
1 . Judging by part
1 Shape and class
Hexagon
head bolt
@Bolt head No*
Hexagon
flange bolt
No mark
Hexagon
head bolt
Hexagon Three protruding
head bolt
Two protruding
lines
Hexagon
flange bolt
Welded
bolt
@ l;')protruding
Class
2. Judging by part No.
Hexagon head bolt
Parts No,
I
91611-do625
Length (rnrn)
Diameter ( m m )
Diameter
Parts No.
~ e n ~ t h
( r n m )
Diameter ( m m )
Diameter

12. STANDARD BOLT TIGHTENING TORQUES

13. PRECOAT BOLTS
(Bolts with seal lock agent coating on threads)
1. Do not use the precoat bolt as itisineither
of the following cases:
(a) After it is removed.
(b) When the precoat bolt is moved Cloos-
ened or tightened) by tightness check,
etc.
Note:
. For torque check, use the lower limit of the Precoat ~~l~~
allowable tightening torque range. If the
bolt moves, retighten it accordicg to the
steps below.
2. Method for reuse of precoat bolts
(I)
Wash ,the bolt and threaded hole. (The (2) Perfectly dry the washed parts by air
threaded hole must be washed even for blowing.
replacement of the bolt.) (3) Coat the specified seal lock agent to the
threaded portion of the bolt.
HIGH PRESSURE HOSE FITTING TIGHTENING TORQUE
1. When connecting a high pressure hose, wipe the hose fitting and mating nipple contact surfaces with
clean cloth to remove foreign matters and dirt. Also check no dent or other damage on the contact
surfaces before installation.
2. When connecting a high pressure hose, hold the hose to align the fitting with the nipple and tighten
the fitting.
3. The maximum tightening torque must not exceed twice.the standard tightening torque.
Nominal diameter
of screw
7116 - 20'UNF
9/16 - 18UNF
314 - 16UNF
7/8 - 14UNF
11/16 - 12UNF
15/16 - 12UNF
PF1/4
PF3/8
PF112
P F3/4
PF1
Hose inside
diarneter (mrn)
6
9
12
12
19
25
9
9
12
19
25
Standard tightening torque kg-m (ft-lb)
Standard
2.5 ( 18.1)
5.0 ( 36.2)
6.0 ( 43.4)
6.0 ( 43.4)
12.0 ( 86.8)
14.0 (101.2)
5.0 ( 36.2)
5.0 ( 36.2)
6.0 ( 43.4)
12.0 ( 86.8)
14.0 (101.2)
Tightening range
2.4 - 2.6 (17.4 - 18.8)
4.8 - 5.3 (34.7 - 38.3)
5.7 - 6.3 (41.2- 45.5)
5.7 - 6.3 (41.2 - 45.5)
11.4- 12.6 (82.4- 91.1)
13.3 -14.7 (96.2 -- 106.3)
4.8 - 5.3 (34.7 -- 38.3)
4.8 - 5.3 (34.7 - 38.3)
5.7 -- 6.3 (41.2 - 45.5)
11.4-12.6 (82.4- 91.1)
13.3 -- 14.7 (96.2 -106.3)

14. FRAME NUMBER (1986.8-- 1989.8)
Punching
position
Vehicle series
Engine model
Vehicle model
Punching format
Vehicle series
Eng~ne
model
Vehicle model
Punching format
Top on rear right frame
-
1 ton series
1 Z
-
-
-
-
-
-
-
-
-
-
4 P
5FG10
02- 5FG10
5FG14
02- 5FG14
5FG15
02- 5FG15
5FG18
02- 5FG18
5FG18 -
10001
4 Y
40- 5FG10
42- 5FG10
40- 5FG14
42- 5FG14
40- 5FG15
42- 5FG15
40- 5FG18
42- 5FG18
405FG18 -
10001
2 ton series
2 J
5FD10
02- 5FD10
5FD14
02 - 5FD14
5FD15
02 - 5FD15
5FD18
02- 5FD18
5FD18 -
10001
4 P
5FG20
02- 5FG20
5FG23
02 - 5FG23
5FG25
02 - 5FG25
5FG25 -
I0001
1 Z
5FD20
02 - 5FD20
5FD23
02 - 5FD23
5FD25
02- 5FD25
5FD25 -
10001
4 Y
40- 5FG20
42- 5FG20
40- 5FG23
42- 5FG23
40- 5FG25
42- 5FG25
405FG25 -
10001
2 J
60 - 5FD20
62 - 5FD20
60 - 5FD23
62 - 5FD23
60 - 5FD25
62 - 5FD25
605FD25 -
10001