PULLER POWERTEAM

1. Pullers
41
41
Highlights:
•Manual & Hydraulic Grip-O-Matic Pullers
•Manual & Hydraulic Super Grip-O-Matic
Pullers
•Manual & Hydraulic Push-Pullers
•55 & 100 Ton Hydraulic Enforcers
•Manual & Hydraulic Puller Sets
•Accessories matched to pullers and
push-pullers
•Internal pulling attachments
•Bearing pulling attachments
•Slide hammer pullers
•Blind hole pullers
•Puller accessories
•The most complete line of Pullers on the
market
•Over 70 years of puller design and manufac-
turing
•Forged and heat treated alloy steel jaws on all
jaw type pullers
•Less than .2% warranty
•Most copied puller in the world
Rev. 7-31-95
HYDRAULIC SUPER
GRIP-O-MATIC
55 TON ENFORCER
MANUAL
SUPER
GRIP-O-
MATIC
HYDRAULIC
PUSH-
PULLERS
MANUAL
GRIP-O-
MATIC
SPECIAL PULLERS
®

2. Rolled “V” Threads Pullers
42
42
Rev. 7-31-95
Rolled threads start with a material O.D. equal
to the pitch diameter of the thread. The rolling
process moves material from below the pitch
diameter and creates a smoother and stronger
thread.
Cut threads start with a material O.D. equal to
the thread O.D.. Cutting can cause tears on the
thread surface which can make it rough and
can cause minute cracks at root of thread which
can open up during heat treat and lessen the
capacity of the screw.
PITCH DIAMETER
OF THREAD
CENTERLINE
OF SCREW
OUTSIDE DIAMETER
OF THREAD
®

3. Manual & Hydraulic Grip-O-Matic and Super Grip-O-Matic Pullers
Features:
•Grip-O-Matic feature on all pullers
•2-way, 3-way and 2/3-way combination pullers
1 to 37 ton mechanical pullers
5 to 50 ton hydraulic pullers
2-1/8”(54 mm) to 27-5/8”(702 mm) reach
3-1/4”(83 mm) to 44”(1,118 mm) of spread
•Forged alloy steel jaws
•Alloy steel heads (forged or flame cut)
•Rolled “V” threads
•Special coating on threads
•Heat treated alloy steel cross bolts
•Standard hydraulic rams on Grip-O-Matic series
•Adjusting nut on Super Grip-O-Matic series
•Machined puller jaw toes
Benefits:
•The harder the pulling force, the tighter the jaws grip
•A wide variety of pullers, select a specific puller for a
specific application or select one or more pullers for
general applications
•Strongest possible part, the grain of the material follows
the contour of the part.
•Heat treated and designed for maximum strength
•Stronger and smoother than cut threads
•Resists corrosion, traps lubrication
Better than black oxide
•Designed for max. shear strength
•Rams can be removed from puller and used in other
hydraulic applications
•Allows for controlled jaw spread adjustment
•Larger and stronger pulling toe than most competitors
43
43
Rev. 2-1-96
®

4. Manual and Hydraulic Push-Pullers Pullers
Features:
•Push-pull feature on all models
•10,17-1/2 and 30 ton manual push-pullers
17-1/2, 30 and 50 ton hydraulic push-pullers
6-1/4”(159 mm) to 30-5/8”(778 mm) of reach
2-1/8”(54 mm) to 20-1/2”(521 mm) of spread
•Standard hydraulic rams
•Forcing screw and leg ends designed to match
accessories
Benefits:
•Designed to remove and install tight-fitting parts
•Each unit has a spread range and optional leg lengths
designed to match the push-puller capacity
•Rams can be removed and used in other hydraulic
applications
•Forcing screws can be matched to internal pulling
attachments; male to female and female to female
threaded adapters, step plates and shaft protectors
Leg ends can be matched to bearing pulling attach-
ments; leg end adapters, male to female and female to
female threaded adapters
44
44
Rev. 2-1-96
®

5. Pulling Attachments Pullers
Bearing Pulling Attachments
Features:
•Knife-like edges
•Wide range of sizes
•Adaptable
•Forged alloy steel puller blocks
Internal Pulling Attachments
Features:
•Remove oil seals, bearing cups and bushings
•Wide range of sizes
•Adaptable
Benefits:
•Allows attachment to be forced behind parts where
space is limited.
•Eight attachments to choose from with capacity ranges
from 2 to 50 ton.
•Can be used with manual or hydraulic 2-jaw pullers,
manual or hydraulic push- pullers and on shop press
bed plates
•Strongest possible part, the grain of the material follows
the contour of the part
Benefits:
•Choice of jaw positions allows pulling attachments to fit
various diameters
•Reaches from 2-1/8”(54 mm) to 5-7/8”(149 mm) and
spreads from 1-1/2”(38 mm) to 9”(229 mm) and
capacities from 10 ton to 30 ton
•Can be used with manual or hydraulic push-pullers and
with slide hammers
45
45
Rev. 7-31-95
®

6. Special Pullers
Pilot Bearing Pullers
Features:
•For pulling motor, generator and magneto bearings and
flywheel pilot bearings
Slide Hammer Pullers
Features:
•Reversible jaws
•Two heads
•Optional jaw lengths
Blind Hole Pullers
Features:
•Expandable collets
•Ten collet sizes
•Bridge and slide hammer
Benefits:
•Choice of ranges, 1/2”(13 mm) to 2-1/8”(54 mm) diam-
eter spreads and 3/4”(19 mm) to 1-3/4”(44 mm) reach
Benefits:
•Pullers can be used for internal or external pulling
•Pullers can be used in 2-jaw or 3-jaw configuration
•Internal spreads from 3/4”(19 mm) to 6-1/4”(158 mm)
external spreads from 3/4”(19 mm) to 7-1/2”(191 mm)
reaches from 1-3/16”(29 mm) to 5”(127 mm)
Benefits:
•Allows the pulling of friction fitted parts from blind
holes
•Gives pulling range of 5/16”(8 mm) to 1-3/4”(44 mm)
diameters
•A choice of two methods of exerting pulling force
46
46
Rev. 7-31-95
®

7. Accessories Pullers
Features:
•Male to female threaded adapters
•Female to female threaded adapters
•Step plate adapters
•Shaft protectors
•Protective blankets
Benefits:
•Adapts push-puller legs to tapped holes in flanges and
gears
Adapts push-puller forcing screws to tapped holes in
shaft ends
Male ends in inch and metric sizes
•Adapts push-puller legs to threaded studs in flanges
Adapts push-puller forcing screws to threaded shafts
Inch and metric sizes available
•Fit hollow shafts so forcing screws on pullers and push-
pullers have a surface to push against
•Protect shaft centers and forcing screw ends from dis-
tortion when extreme pressures are applied
Used with pullers and push-pullers
•Contains broken or flying parts in most pulling, press-
ing, pushing or stressing jobs
47
47
Rev. 7-31-95
®

8. Sets Pullers
Features:
•Each set is a combination of pullers, push-pullers, spe-
cial pullers, attachments and accessories
•Manual sets, hydraulic sets and combination sets
•Storage options
Benefits:
•Eleven sets to choose from, have the puller you need,
on hand, when you need it
•Three manual sets, two ten ton sets and one 17-1/2 ton
set
Three hydraulic sets, one each 17-1/2 ton, 30 ton and
50 ton
Five combination manual and hydraulic sets
10 ton, 17-1/2 ton, 17-1/2 & 30 ton, 17-1/2 & 50 ton
and 17-1/2, 30 and 50 ton master set
•Select from wall boards, wall hanging storage boxes,
wood boxes or metal boxes
48
48
Rev. 7-31-95
®

9. 55 Ton Enforcer Pullers
Features:
•Grip-O-Matic pulling feature
•Only cart mounted puller in this capacity on the market
today
•Cart is equipped with hydraulic lift system
•Unique dual pump
•Hydraulically actuated jaws
•2-or-3 jaw configuration
•Self-centering
•Guards at pinch points
•Swivel casters and large wheels
•Lifting eyes
•Four ram extensions
•Choice of pushing rams and jaw lengths
•Remote control
Benefits:
•The harder the pulling force the tighter the jaws grip.
•Puller is easily moved from job to job
•Puller height can be precisely adjusted from 12”(305
mm) to 42”(1067 mm)
•Low pressure pump adjusts jaws and high pressure
pump advances pushing ram
•Ram moves jaws in and out to provide safe & secure
grip on part
•Permits pulling wheels and other parts with odd or even
number of spokes
•Center ram on work, the jaws will automatically grip the
work evenly
•Protects operator
•Easy movement & maneuverability
•Permits use of overhead crane to raise entire unit
•Matched to the ram, shorten pushing stroke
•6-1/4”(159 mm) & 13-1/4”(337 mm) stroke rams and
standard or extra long jaws, match to suit your applica-
tion
•20 ft. (6.1 m.) cord on remote hand control allows oper-
ator to stand away from work-piece.
49
49
Rev. 7-31-95
®

10. 100 Ton Enforcer Pullers
Features:
•Grip-O-Matic pulling feature
•Adjustable jaws
•Lifting bracket
•Adjusting screw
•Spring loaded feature
•Tow bar and large wheels
•Pushing adapters
•Power pump
•Remote control
Benefits:
•The harder the pulling force the tighter the jaws grip
•Jaws can be adjusted so that they always pull on a flat
surface
•Puller can be lifted if workpiece center line is more than
36”(914 mm) off floor
•Puller centerline has vertical adjustment of 12”
(305 mm) to 36”(914 mm)
•Puller will align itself
•Makes moving puller easy
•Six pushing adapters, 2-1/2”(64 mm) and 4-1/8”
(105 mm) diameters. Matched to the ram, shorten
pushing stroke
•1-1/8 H.P., 115 volt two stage pump also available in
220 volt, 50 HZ
•25 foot (7.6M) cord on remote hand control allows
operator to stand away from work-piece.
50
50
Rev. 7-31-95
®