This document provides steps to configure an outdoor wireless access point in client router mode to connect to a wireless internet service provider's access point. It then describes how to use a broadband router connected to the access point to create a new subnet and extend the wireless network to additional devices. The steps include resetting the access point, selecting client router mode, scanning and connecting to the WISP's network, and configuring the broadband router's LAN and WAN settings to establish a new subnet for local network devices.

1. How–To setup Wi-Fi Client Router Mode [CPE]connect to [WISP AP]
And Using Broadband Router to Create New Sub-Network (subnet)
1. Wi-Fi (Wireless Long distance Internet Access)
WiFi
Wi-Fi” LAN admin
broadband router
WPA Smart Phone, Laptop, Tablet PC
Reset WANIP Setting mode
Client Router WISP
AP 2 smart phone / PDA tablet pc
Outdoor Wireless
Access Point broadband router
Gateway
2 mode Client Router
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 1 of 7

2. | Network Diagram and Devices
Outdoor Wireless Access Point (AP) as CPE (mode: Client Router) with LAN Cables & POE
Broadband Router & Accessories and LAN Cables
3. Conceptual Diagram
4 WAN LAN settings Outdoor Wireless Access Point [CPE]
5 WAN LAN settings
Broadband Router( )
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 2 of 7

3. | Step-by-Step
1. Reset your AP to default factory, My Device I useEOC-2610 as CPE
2. Open web console of your AP point your browser to http://192.168.1.1
3. Select Operation Mode as “Client Router” in system properties Click Apply
4. Go to menu “Wireless Network”  Click “Site Survey”
5. Select Wi-Fi ISP that you want to connect select mac address on “BSSID” Column
AP (WEP Key / WPA PSK )
/ Supply WEP Key or WPA PSKthis step.
6. Click Apply then you can see the connection status on menu “Connection Status”
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 3 of 7

4. 7. Setup Sub Network,
Open Web console of Broadband Router(I use ASUSTEK WL-500gP v2)
Connect byusingdefault IP address http://192.168.1.1
Please change to new ip if the LAN IP of your router same as Outdoor Access Point (AP)
8. Change IP address of Router to new subnet, I use 192.168.2.1 on LAN IP Setting(Option)
9. Click Apply Click Finish click “Save & Restart” and wait for 20sec to restart(Option)
10. Open Web console of Broadband Router by default IP address http://192.168.2.1
11. Change TCP/IP Setting of WAN to Automatic IP ( 5)
a. Use Automatic IP(Receive IP Address, subnet Mask, Default Gateway)
b. Use Auto Negotiation for Speed
c. DNS Server 1 use DNS’s IP
12. Click Apply Click Finish click “Save & Restart” and wait for 20sec for router restart
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 4 of 7

5. 13. Configure IP Scope for Sub Network and Verify your DHCP Server Setting
14. Click Apply Click Finish click “Save & Restart” and wait for 20sec for router restart
15. After the router was restart this how-to is completed!
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 5 of 7

6. PC Laptop Smart Phone LAN
TCP/IP WL500gpV2 Router basic network
information
Network and Sharing Center
Network Connection Details Local Area Connection
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 6 of 7

7. latency 20ms
1.4 Wi-Fi Client Router WISP AP Wi-Fi
By Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 7 of 7