1. 1
Implementation of “INTERNATIONAL STANDARD –ISO/IEC 17025” –
General requirements for the competence of testing and calibration
laboratories-summary
Chandran.udumbasseri, Technical consultant
cudumbasseri@yahoo.co.in.
1. Scope
For competence to carryout test and calibration, it covers calibration performed, using
standards, non standards and laboratory developed
The scope explains the competency of the laboratory to carry out tests and calibrations.
There are two types of laboratory. Some laboratory does only testing and analysis and
gives calibration of instruments for external calibration agency or laboratory. This
definitely adds expense to the laboratory. This may be due to the fact that laboratory
personnel are not competent enough to carry out calibration themselves. Sometimes NIT
traceable standards are not available for such laboratory. Nations importing international
standards are regularized by the government and in such countries laboratories have to
give the calibration work to external agencies.
If the laboratory has the capability to carry out both testing and calibration and have
laboratory personnel having required competency then such laboratory can go for
registration to ISO17025
Here the calibration standards are those procured from international agencies and NIT
traceable standards.
The scope explains calibration using non standards meaning these standards need not be
traceable to NIT standards, but may be a secondary type whose traceability can be
achieved through secondary standards.
The scope also explains developing new calibration methods in the laboratory. Sometime
it is necessary to develop new calibration methods suitable for the laboratory. In such
cases method development, statistical method application to get repeatability and
reproducibility data for the new methods should be documented
So requirements are:
Well equipped laboratory that can conduct testing and calibration
Qualified laboratory personnel having competency in developing new methods of testing
and standardization
Check list
Document all calibration evidences and certificates
Document new method developments, statistical results and evidence that can support
Document the trainings given to the laboratory personnel with an objective to improve
their efficiency
Applicable to all organizations performing tests and calibration
Scope of applying this standard is wider with respect to testing laboratories. It can be a
part of an organization or independent
Applicable to all laboratories regardless of number of employees
There is no restriction on the number of laboratory personnel to get registered to his
standard
2. 2
For use by laboratories in developing their management system for quality,
administrative and technical operations
The scope is to develop as a quality management system for the laboratory both
administrative and technical operations.
Laboratory customers, regulatory authorities and accreditation bodies may use this to
confirm and recognize competence of the laboratories.
A laboratory accredited to this standard is a bench mark to recognize as competent
laboratory. Customers of the laboratory and other regulatory bodies both government and
non government organization can recognize the laboratory as competent
Compliance with regulatory and safety requirements are not covered by this standard
The scope of this standard should not be considered as an approval for compliance to
regulatory requirements of local government bodies and safety requirements of
international safety organizations (OSHA, etc..)
This standard covers the requirements of ISO 9001 quality management system. This
standard also covers technical competence that are not covered by ISO 9001
This standard encompasses the requirements of ISO9001 QMS. So separate accreditation
from ISO9001 is not insisted
Additionally this standard necessitates the requirement of technical competency of
laboratory and laboratory personnel.
4. Management requirements
4.1. Organization
Laboratory should carry out testing and calibration to meet the requirements of this
standard
Evidences should be documented on the work conducted by the laboratory to ensure that
the requirements of the standard is properly followed
The management system shall cover work carried out in its permanent facilities, at sites
and or at associated temporary facilities
The works to be included and audited are the one carried out in the laboratory itself. The
work done in a customer’s site is also included for auditing. If it is necessary to conduct
work in some other type of temporary facilities then such work will also be audited as per
the compliances requirements.
Laboratory as a part of an organization should have a responsible person at key position
to avoid any influence or conflict from the organizations other sections
The laboratory is considered as independent in its management from the rest of the
organization. Its decision should not be jeopardized from the bias of the rest of the
organization. Laboratory should have a responsible person at the key position whose
decision is the final one regarding the work and management of the laboratory.
The laboratory shall have managerial and technical personnel who have authority and
resources to carry out their duties (testing and calibration activities, modification,
rectification, improvement of these areas of work)
This emphasizes above requirements. The organization should delegate authority along
with responsibility to the key person of the laboratory.
The personnel should not be influenced by pressure like internal and external commercial
and financial which affect the work adversely
3. 3
The decision on work to be carried out in the laboratory should not be influenced by the
pressure from any person internal and external to the laboratory which may not be useful
and fruitful to the laboratory.
Should have policies and procedures to protect the customer’s interest and proprietary
rights
The laboratory needs a separate policy statement and should be exhibited to the public to
understand the priorities of the professionals and laboratory personnel to follow in their
work. The policy should imply customer’s interest and their proprietary rights
Should have policies and procedures to avoid situation that diminish confidence of the
customer
The content of the policy should be to boost customer confidence in the work
accomplishment of the laboratory
Should have defined organizational and structural relationship with the rest of the
organization-quality management, technical operation and support services
The organizational chart showing relationship of laboratory with the rest of the
organization, hierarchical relationship of laboratory personnel, transformation of
customer needs and requirements in to product and services that satisfies the customer
and enhance customer to supplier relationship
Should specify the responsibility, authority and inter relationships of all personnel who
manage, perform, and verify the quality of tests and /or calibration
Job description of each laboratory personnel should be documented. It should specify
responsibility, authority, inter relationship of each designated levels with the rest of the
organization. The relationship should indicate the work flow, quality testing/ calibration
work and assurance of quality that satisfy the customer needs and requirements.
Should provide adequate supervision of testing and calibration and training by a person
familiar with methods and procedures, purpose of each test or calibration and assessment
of the test and or calibration results
Should have technical management for supervising technical operation and the provision
of resources
Should appoint a quality manager, with defined responsibility and authority for ensuring
the management of quality that are followed at all times, he should have direct access to
higher level of management where decision are made relating to laboratory policies and
resources
Should appoint deputies for key managerial personnel
Should have awareness of their activities and ability to contribute for achieving
management objectivities.
4.2. Management system
The laboratory shall
Establish, implement and maintain a management system appropriate to the scope of
its activities
Document its policies, system, programs, procedures and instructions to the extent
necessary to assure the quality in testing and calibration
Communicate Documentation which should be understood and implemented
Define management system policies (statement) with quality manual
Establish overall objectives
Review during management review
4. 4
Issue Quality Policy Management under the authority of top management
The policy statement should include:
Commitment of laboratory to good professional practice and to its customer to serve
with quality in testing and calibration
Management’s statement of the laboratory’s standard of service
Purpose of management system related to quality
Requirement that all personnel concerned with testing and calibration should
familiarize quality documentation and implement policies and procedures in their
work
The laboratory management’s commitment to comply with this international standard
and to continually improve the effectiveness of the management system
Top management shall provide evidence of commitment to development and
implementation of management system
Top management shall communicate to the organization the importance of meeting
customer requirements government regulations
The quality manual shall include or make reference to the supporting procedures
including technical procedures. It shall outline the structure of documentation used in the
management system
The roles of technical management and quality manager should be defined in the quality
manual so as to comply with this international standard.
Top management should ensure integrity of management system and maintained while
changes in the system are planned and implemented
4.3. Document control
All laboratory documents shall be established, maintained and controlled
4.3.2. Document approval and issue
☼ All the documents used in the laboratory should be reviewed and approved by
authorized personnel. A list of all documents controlled with their revision status and
distribution shall be established and available
Ensure that
Appropriate controlled documents are available at all locations where operations are
essential
Documents are periodically reviewed and revised wherever necessary for suitability
and compliance
Obsolete documents should be removed from all locations of use
Any obsolete document retained for any legal or knowledge preservation shall be
marked
Documents generated by laboratory shall include, the date of issue, revision number,
page number, total number of pages or a mark to identify the end of document and the
issuing authority
5. 5
4.3.3. Document changes
o Changes in document shall be reviewed and approved by the same function that
performed original review. Otherwise specify the new designation to have access to and
ability for review
o If possible, altered text should be identified in the document
o If document amendment is allowed by hand, the required procedure with authorities shall
be defined (amendments shall be clearly marked, initialed and dated)
o A proper procedure for controlling documents stored in the computer shall be maintained
4.4. Review of requests, tenders and contracts
₤ The laboratory shall establish and maintain procedures for the review of requests, tenders
and contacts. The policies and procedures ensure that:
₤ The requirements including methods to be used should be defined, documented and
understood
₤ The laboratory has the capability and resources to meet the requirements
₤ The appropriate method is selected and is capable of meeting the customer’s
requirements
₤ Records of reviews shall be maintained including discussions with customer
₤ Subcontracted work review should also be maintained
₤ Deviation from the contract should be informed to the customer
₤ If any amendment needed to contract, then the process of preparation of contract should
be repeated and any amendment shall be communicated to all affected personnel
4.5. Subcontracting of tests and calibrations
◙ When subcontracting a work, then ensure that sub contractor is competent so that the
subcontractor complies with this international standard.
◙ The laboratory shall inform in writing to the customer about the new subcontractor and if
possible get approval for the customer
◙ The laboratory is responsible for the work of the subcontractor unless specified by the
customer for a specific subcontractor.
◙ The laboratory should keep a register for all subcontractors with their compliance to
international standard as evidence
4.6. Purchasing services and supplies
∆ Laboratory should have policy and procedure for the selection and purchasing of services
and supplies. Procedures for reception and storage of reagents and consumable materials
shall be documented
∆ The purchased items shall be inspected /verified to comply with the specification
requirements. The records of action shall be maintained
∆ Purchase order documents should be accompanied with data and specification to which
the purchased material should comply. These documents should be properly reviewed
before realizing to supplier.
∆ Laboratory should conduct suppliers’ evaluation (auditing) and maintain records of
evaluation
6. 6
4.7. Service to the customer
◘ The laboratory shall be willing to cooperate with the customer in clarifying customer’s
request and monitoring laboratory performance in relation to the job work executed
◘ The laboratory shall seek feedback from the customer. This feedback should be used to
improve management system
4.8. Complaints
♦ Laboratory shall have a policy and procedure to resolve customer complaints. Records of
such complaints and their corrective/preventive action records should be maintained.
4.9. Control of non conforming testing and /or calibration work
☼ The laboratory should have policy and procedure to control non conformance work. the
policy and procedure should ensure that:
□ The responsibilities and authorities for managing non conformance work shall be
defined and implemented when a non conformance work was identified
□ The non conformance work should be evaluated
□ Correction should be taken immediately
□ Customer should be notified about non conformance work and work should be
recalled
□ The responsibility for authorizing the resumption of work should be defined
☼ If the recurrence of non conformance work is doubted, then a corrective action as per
section 4.11 should be followed.
4.10. Improvement
► The laboratory should continually improve the effectiveness of management system
through the use of quality policy, quality objectives, auditing, analysis of data, corrective
and preventive action and management reviews
4.11. Corrective action
◊ The laboratory shall establish policies and procedures and designate personnel with
appropriate authorities to implement corrective action for non-conforming works (non
conformance to policies and procedures of management system or technical operations)
4.11.2. Cause analysis
♦ The procedure for corrective action should start with investigation for root causes of the
problem
4.11.3. Selection and implementation of corrective action
♀ The laboratory shall identify the potential corrective actions that can prevent recurrence
of the same problem. Corrective action report shall be documented with evidence of
follow up of actions for changes
7. 7
4.11.4. Monitoring corrective action
♯ The effectiveness of corrective action shall be monitored
4.11.5. Additional audits
◌ If the non conformities are non compliance with laboratory’s policies and procedures, an
audit should be conducted as given in 4.14 as soon as possible
4.12. Preventive action
→ If the non conformities concerning either technical operation or management system are
for the preventive action or improvement opportunities the actions should be planned,
implemented and monitored. The result shall show reduction in occurrence of such non
conformities and advantage from the opportunities for improvement
4.13. Control of records
╨ Laboratory shall establish and maintain procedures (for identification, collection,
indexing, access, filing, storage, maintenance and records disposal). Quality records
include internal audit reports and management reviews and corrective &preventive
actions
╨ All records should be stored, preserved and easily retrievable as and when required and
prevented from losing throughout the period of retention time established.
╨ All records should be secured and in confidence
╨ Electronically stored records should be protected and backed up and prevent from
unauthorized access
4.13.2. Technical records
♠ The laboratory shall retain records of original observations, data and information,
calibration records, staff records, a copy of each test report, calibration certificates issued,
for a definite period. The records should have sufficient information that affects
uncertainty to enable repeating tests if required. The records should have information of
personnel responsible for sampling and testing and result validation.
♠ Observations, data and calculations shall be recorded at the time they are made
♠ When mistakes occur in records, each mistake should be crossed and not erased. The
correct value should be entered alongside. Any alteration in records should be signed or
initialized by the person making the correction
4.14. Internal audits
♂ The laboratory shall conduct internal audits periodically to ascertain compliance with
management system and this international standard. The internal audit program shall
address all elements of the management system. The quality manager plans and organizes
audits as required by the schedule and requested by the management. This audit shall be
carried out by trained and qualified personnel and shall audit independent of the activity
to be audited.
♂ All audit findings that shows doubt on any results should be followed by corrective
action. The customers shall be notified about the non conformities of results
8. 8
♂ The area of activity audited, the audit findings, and corrective actions shall be recorded
♂ The implementation and effectiveness of corrective actions shall be followed and
verified.
4.15. Management reviews
ằ The laboratory management shall conduct a periodic review of the management
system at regular scheduled time to ensure the effectiveness and suitability of
management system and introduce necessary changes or improvements
ằ The review shall include:
ᾀ Suitability of policies and procedures
ᾀ Reports from managerial and supervisory personnel
ᾀ Outcome of recent internal audits
ᾀ Corrective and preventive actions
ᾀ Assessment of external bodies
ᾀ The results of inter-laboratory comparisons or proficiency tests
ᾀ Changes in the volume and type of work
ᾀ Customer feedback
ᾀ Complaints
ᾀ Recommendations for improvement
ᾀ Other relevant factors, such as quality control activities, resources and staff
training
ằ Findings from management reviews and actions that arise shall be recorded; the
action should be carried out within appropriate and agreed timescale
5. Technical requirements
ṱ The factors that determine the correctness of tests and calibration are:
ẹ Human factors
ẹ Accommodation and environmental conditions
ẹ Test and calibration methods and method of validation
ẹ Equipment
ẹ Measurement traceability
ẹ Sampling
ẹ The handling of test and calibration items
ṱ The factors contributing to the total uncertainty measurement differs between tests
and between calibrations. These factors should be accounted during developing test
and calibration methods, during training personnel and during selecting calibration of
equipments
5.2. Personnel
ṩ The laboratory management shall ensure the competence of all who operate specific
equipment, perform tests and calibration, result evaluation and authorizing the test
reports and calibration certificates. Staff under training shall be supervised. Specific
tasks should be performed by qualified personnel with appropriate education,
training, experience and skills
9. 9
ṩ The management shall formulate the goals with respect to education, training and
skills of the laboratory personnel. Laboratory should have policies and procedures for
identifying and training needs and providing training to personnel. These trainings
shall be relevant to the present and anticipated tasks of the laboratory. The
effectiveness shall be evaluated.
ṩ The laboratory shall use personnel who are employed or can use personnel hired
through contract. But hired personnel should be supervised and competency at work
in accordance to the laboratory management system should be evaluated.
ṩ Laboratory shall maintain job descriptions for managerial, technical and key support
personnel involved in tests and calibrations
ṩ The management shall authorize specific personnel to perform sampling, test and
calibration, to issue test reports and calibration certificates, to give opinions and
interpretations and operate particular type of equipments. The laboratory shall
maintain records of the relevant authorizations, competence, educational and
professional qualifications, training and skills and experience of all technical
personnel, including contracted personnel. This information shall be readily available
and shall include the date on which authorization and competence is confirmed.
5.3. Accommodation and environmental conditions
ṙ The laboratory facilities including lighting and environmental conditions shall be to
facilitate correct performance
ṙ The laboratory should ensure that the environmental conditions do not invalidate the
results or adversely affect the required quality of any measurement. Particular care
should be taken when testing and calibration are conducted at site other than
permanent laboratory. Technical requirements for accommodation and environmental
conditions that can affect the results shall be documented
ṙ The laboratory shall monitor, control and record environmental conditions as required
by the relevant specifications, methods and procedures or where they influence the
quality of the results. Due attention shall be paid to biological sterility, dust,
electromagnetic disturbances, radiation, humidity, electrical supply, temperature and
sound and vibration levels. The tests and calibration should be stopped when the
environmental conditions jeopardize the results
ṙ There shall be separation between incompatible conditions. Cross contamination
should be avoided
ṙ The area affecting the quality of the test and calibration shall be controlled. The
laboratory decides the extent of control
ṙ Measures shall be taken to ensure good housekeeping in the laboratory. Special
procedures shall be prepared if necessary
5.4. Test and calibration methods and method validation
The laboratory shall use appropriate procedures for sampling, handling, transport, storage
and preparation wherever applicable. An estimation of measurement uncertainty and
statistical techniques for analysis of test and calibration data can be applied.
The laboratory shall have instructions on the use and operation of all equipments. All
instructions, standards, manuals and reference data relevant to the work of the laboratory
10. 10
shall be kept up to date and shall be made available to personnel. Deviations from test
and calibration methods shall occur only if the deviation has been documented,
technically justified, authorized and accepted by the customer.
5.4.2. Selection of methods
The laboratory shall use test and calibration methods, including sampling methods which
meet the needs of the customer and which are appropriate for the tests and calibrations.
Methods published in international, regional or national standards (or reputed
organizations/relevant scientific texts/journals, or specified by the manufacturer of the
equipment) shall be used. Methods developed by the laboratory may also be used. The
customer shall be informed of the method chosen. The laboratory shall confirm that it can
properly operate standard methods
The laboratory shall inform the customer when the method proposed by the customer is
considered to be inappropriate.
5.4.3. Laboratory developed methods
The laboratory developed methods shall be a planned activity and shall be assigned to
qualified personnel equipped with adequate resources
All the development stage of the method shall be communicated to all personnel involved
in the method development
5.4.4. Non-standard methods
If standard methods are not available, non standard methods may be used by an
agreement with the customer for particular specification measurement.
5.4.5. Validation of methods
Validation is the confirmation by examination for objective evidence as the requirement
fulfillment for specific intended use.
The laboratory shall validate non-standard methods, laboratory developed methods,
standard methods used outside their intended use and any amplification and modification
of standard methods. The validation shall be extensive to meet the needs of the given
application. The laboratory shall record the results obtained and the procedure used for
validation
When some changes are made in the non-standard methods, the influence of such
changes should be documented
The range and accuracy of the values obtainable from validated methods shall be relevant
to the customer’s needs.
5.4.6. Estimation of uncertainty measurement
A calibration/testing laboratory performing its own calibrations shall have and shall apply
a procedure to estimate the uncertainty of measurement for all calibrations and types of
calibrations
Testing laboratories shall have and shall apply procedures for estimating uncertainty of
measurement. In certain cases valid statistical data may preclude in the calculation of
uncertainty measurement. In such identify the components of uncertainty and make more
reasonably acceptable calculation. Such reasonable estimation should be based on the
performance of method and must use previous experience and validation data.
11. 11
When calculating the uncertainty all components should be taken into account (Sources
of uncertainty include, the reference standards and materials, methods used, equipments
used, environmental conditions, properties and condition of tests).
5.4.7. Control of data
Calculation and data transfers shall be subjected to appropriate checks in a systematic
manner
When computers are used for processing, then ensure that:
◘ The computer software is documented in sufficient detail and suitably validated
◘ Procedures are established and implemented for protecting the data
◘ Computers are maintained to ensure proper functioning
5.5. Equipment
The laboratory shall be furnished with all items of sampling, measurement, and test
equipment for correct performance of tests and calibration
Equipment and its software used for testing, calibration and sampling shall be capable of
achieving the accuracy required and shall comply with specification relevant to tests. The
equipment shall be calibrated before placed for regular service. It shall be calibrated
before use.
Equipment shall be operated by authorized personnel. Up to date on the use and
maintanance of equipment shall be readily performed by appropriate personnel
Each item of equipment and its software used for testing and calibration shall be uniquely
identified.
Records shall be maintained of each item of equipment and its software The records shall
include:
Identity of the equipment and its software
Manufacturer’s name, type identification and serial number
Checks that the equipment complies with the specification
The current location
The manufacturer’s instructions
Dates, results and copies of reports and certificates of all calibrations, adjustments,
acceptance criteria and the due date of next calibration
Maintenance plan and maintenance carried out date
Any damage, malfunction, modification or repair to the equipment
The laboratory shall have procedures for safe handling, transport, storage use and planned
maintenance of measuring equipment to ensure proper function
Malfunctioning equipments shall be taken out of service. It should be labeled or marked
out of service
All equipments under control of the laboratory and requiring calibration shall be labeled,
coded or otherwise identified to indicate status of calibration with last and next
calibration dates
When equipment goes out of the control of laboratory, the calibration status of the
equipment are checked and shown to be satisfactory before the equipment is returned to
service
When intermediate checks are needed to maintain confidence in the calibration status
such checks shall be carried using defined procedure
12. 12
When calibrations give rise to correction factors the updating procedure should be carried
out.
The calibrated equipments shall be safeguarded against adjustments
5.6. Measurement traceability
All equipments used for the measurement should be calibrated before putting in to
service to keep the accuracy and reliability of results.
5.6.2. Specific requirements
5.6.2.1. Calibration
For calibration laboratories, the program for calibration shall be designed and operated.
The calibration and measurement should be traceable to the International System of Units
A calibration laboratory establishes to its own measurement standards and the measuring
instruments to the SI by means of unbroken chain of calibrations or comparison to
primary standards of the SI units of measurement. The link to SI units may be achieved
by reference to national measurement standards. National measurement standards may be
primary standards (primary realization of SI units based on fundamental physical
constants) or may be secondary standards which are standards calibrated by another
national metrology institute. When using external calibration services traceability of
measurement shall be assured by the use of calibration services of laboratories that can
demonstrate competence, measurement capability and traceability. That calibration
certificates issued by these laboratories shall contain the measurement results including
uncertainty measurement and statement of compliance with an identified metrological
specification.
Calibrations that cannot be made in SI units shall provide confidence in measurements by
establishing traceability to appropriate measurement standards
The use of certified reference materials provided by a competent supplier
The use of specified methods and standards
5.6.2.2. Testing
For testing laboratories, the requirements given in 5.6.2.1 apply for measuring and test
equipment with measuring functions used if the associated contribution from the
calibration contributes little to the total uncertainty of the test results. In such situation,
the laboratory shall ensure that the equipment used can provide the uncertainty of
measurement needed.
Where traceability of measurements to SI units is not possible, the same requirements for
traceability to certified reference materials, agreed methods and consensus standards are
required as for calibration laboratories.
5.6.3. Reference standards and reference materials
5.6.3.1. Reference standards
The laboratory shall have a program and procedure for the calibration of its reference
standards. Reference standards shall be calibrated by a body that can provide traceability
(5.6.2.1). These reference standards should be preserved exclusively for calibration only.
Reference standards shall be calibrated before and after any adjustment.
13. 13
5.6.3.2. Reference materials
Reference materials shall be traceable to SI units of measurement or to certified reference
materials. Internal reference materials shall be checked if economically feasible.
5.6.3.3. Intermediate checks
Intermediate checks are needed for all standards and reference materials to maintain
confidence.
5.6.3.4. Transport and storage
The laboratory should have safe handling procedures (handling, transport, storage and
use) for reference standards and materials to prevent contamination and deterioration.
5.7. Sampling
The laboratory shall have a sampling plan and procedures for sampling of materials for
testing and calibration. The sampling plan and procedures should be available at the
location from where the samples are collected. The sampling procedure should be based
on statistical methods. The sampling process shall specify factors to be controlled to
ensure validity of test and calibration.
If the customer requires deviations, additions or exclusions from the documented
sampling procedure, these shall be recorded in detail with the appropriate data and shall
be included in all documents of testing and calibration
The sampling procedure for recording data should include identification of sampler,
environmental conditions and diagram or equivalent means to identify the sampling
location, also sampling statistics to be used.
5.8. Handling of test and calibration items
The laboratory shall have procedures for transportation, receipt, handling, protection,
storage, retention and disposal of test and calibration items. It should include provisions
to protect the interest of laboratory and customer
The laboratory shall have a system for identifying test and calibration items. The
identification shall be retained throughout the life of the item in the laboratory. The
system shall be operated to ensure that items cannot be confused physically.
When the test or calibration item is received, departure from normal conditions shall be
recorded. When there is doubt about the suitability of this type of received item, the
matter may be discussed with the customer and take a decision to proceed with the same
damaged item. The discussion shall be recorded.
The laboratory shall have procedures and appropriate facilities for avoiding deterioration,
loss or damage to the test or calibration item during storage, handling and preparation.
Instructions forwarded with the item shall be followed in handling, storage and these
conditions should be maintained, monitored and recorded throughout the item storage
with the laboratory.
5.9. Assuring the quality of test and calibration results
The laboratory shall have quality control procedures for monitoring the validity of tests
and calibrations undertaken. The resulting data shall be recorded to understand trends and
if possible statistical techniques shall be applied to review the results. The monitoring
may include:
Regular use of certified materials, internal quality control using secondary reference
materials
14. 14
Participation in inter-laboratory comparison or proficiency testing program
Replicate test or calibration using the same or different methods
Retesting or recalibration of retained items
Correlation of results for different characteristics of an item
Quality control data shall be analyzed and outliers are found planned action shall be taken
to correct the problem and to prevent incorrect results from being reported.
5.10. Reporting the results
The results of tests or calibration carried out by the laboratory shall be reported
accurately, clearly, unambiguously and objectively and in accordance with any specific
instruction in the test or calibration methods.
The result shall be reported in a test report or a calibration certificate and shall include all
information requested by the customer and necessary for the interpretation of the results
and all results required by the method used (5.10.2, 5.10.3 or 5.10.4)
If the test or calibration is performed for an internal customer the report may be in a
simplified way. But any information (not reported to customer) as given in section 5.10.2
to 5.10.4 shall be with laboratory
5.10.2. Test reports and calibration certificates
o Each test report and calibration certificate shall include:
♦ The title
♦ The name and address of the laboratory and the location where the tests and
calibrations were carried out
♦ Unique identification of the report or certificate (serial number), page identification a
clear identification of the end of the report or certificate
♦ The name and address of the customer
♦ Identification of the method used
♦ A description of, the condition of, and unambiguous identification of the item tested
or calibrated
♦ The date of receipt of the test or calibration item where this is critical to the validity
and application of the results, and the date of performance of the test or calibration
♦ Reference to the sampling plan and procedures used by the laboratory
♦ The test or calibration results with units of measurement
♦ The name, function and signature or equivalent identification of person authorizing
the test reports or calibration certificates
♦ A statement to the effect that the results relate only to the items tested or calibrated.
5.10.3. Test Reports
In addition to the requirements listed in 5.10.2, the test report shall include:
◘ Deviation from, addition to or exclusion from the test method, and information on
specific test conditions, such as environmental conditions
◘ A statement of compliance /non compliance with requirements and specification
◘ If applicable, a statement on the estimated uncertainty of measurement (information
on uncertainty is needed when there is relevant to validity or customer requires or
compliance to specification needs justification from uncertainty)
◘ If needed opinions and interpretations
◘ Additional information required by specific methods, or customers
15. 15
In addition to requirements listed in 5.10.2 and above (5.10.3) reports on sampling shall
include:
◘ Date of sampling
◘ Unambiguous identification of the substance
◘ The location of sampling (may be with diagram, photographs)
◘ Reference to sampling plan and procedures
◘ Details of any environmental conditions during sampling that can help the result
interpretation
◘ Any standard specification for the sampling methods, deviations additions to,
exclusions from the specification concerned
5.10.6. Opinions and interpretations
When opinions and interpretations are included the basis of such writings should be
included in the document and the opinions and interpretations shall be clearly marked.
5.10.6. Testing and calibration results obtained from subcontractors
♦ If the final document (report/certificate) contains results performed by the subcontractors,
these results shall be clearly identified
♦ When the calibration is conducted by subcontracted laboratory, it should issue calibration
certificate to the main contracting laboratory
5.10.7. Electronic transmission of results
☼ If the results are transmitted electronically (phone, fax, any electronic medium) this
should meet the requirements of this international standard section 5.4.7.
5.10.8. Format of reports and certificates
→ The format shall be designed to accommodate each type of test/certificate to minimize
misunderstanding/misuse.
5.10.9. Amendments to test reports and calibration certificates
◙ Amendments to a report or certificate after its issue to the customer shall be made only in
the form of a further document which include the below statement
“Supplement to test report (calibration certificate), serial number….”
Such amendments should be subjected to this international standard.
◙ When a new report or certificate has to be issued, this shall be uniquely identified and
shall contain a reference to the original one that it replaces.