3. Expert knowledge in the
chemical field, attention to
customer needs, maximum
efficiency and quality:
all of this is ICR - Industria
Chimica Reggiana, which
has been a benchmark for
varnishingin the auto-body,
industrial, composite and
natural stone sectors
since 1961.
The wide range of solutions that it offers is
designed by a team of specialized technicians
who aim to get the maximum in terms of
technological innovation, performance and
cost/benefit ratio.
Present in more than 100 countries around the
world, solid, stable and continuously growing, ICR
is an international company that does not intend
to give up its calling for customization, evident not
only in its attention dedicated to the development
and creation of each product, but the readiness
with which it serves every single customer, assisting
them throughout every phase of the purchase.
A BIG COMPANY AT A HUMAN DIMENSION
ICR SPRINT COMPOSITES | 3
4. ICR is founded and
immediately dedicates
itself to the production
of chemical articles for
bodywork and natural
stones.
1961
Debut on the market
of the Sprint brand,
which immediately
distinguishes itself in the
car refinish sector.
1962
The process of
internationalisation
begins: the first sale
in Kuwait dates back
to this year.
1973
ICR opens new markets
in Africa, Asia and
Latin America, where
it operates with a solid
network of subsidiaries,
licensees and qualified
distributors.
1985 - 1995
ICR enters the world of
color with the purchase
of Brenen Italiana with
its Offices in Perugia,
the historic brand of
industrial paints.
2001
The subsidiary ICR
Ibérica is founded in
Spain.
1969
ICR grows in the
markets of Eastern
and Western Europe.
1980
The R&D laboratories
develop the early
products specific
for the Industry
market.
1998
MADE IN ITALY EXCELLENCE
4 | ICR SPRINT COMPOSITES
5. ICR launches Sprint
Coatings and the Sprint
Mix tinting machine,
solutions suitable for the
general industry and for
industrial bodywork.
2008
ICR acquires 30,000
mq of factory space in
Lodi meant specifically
for the production of
paints.
2011
Innovation continues:
creation of the air-dried
UHS transparent paints
which, thanks to the
evolved ICR technology,
satisfy the new needs of
the car refinish market.
2015
ICR has acquired
ProWorx, leader in
car refinish fillers in
the United Kingdom.
The transaction allows
this important country
to be better served
and to expand the
offer of car repair
products dedicated
to the Anglo-Saxon
market. The international
expansion is continuing
in the same fashion after
being undertaken in the
perspective of having a
direct presence in the
markets. It earlier led to
the opening of ICR Sprint
Inc., headquartered in
Fall River, MA (USA), in
2017.
2018
ICR acquires the
technologies to statisfy
the needs of special
coatings like silk screen
printing of automobile
logos and lacquering
of design and plastic
objects.
2010
ICR starts the production
of E-coating, solutions
addressing the market
of electrodeposition
techniques.
2013
The Company enters
the world of car color:
introduction of Sprint
Evolution color system,
high performance tinting
machine comprising
over 85,000 formulae
and 15,000 cards.
2016
ICR launches the
tintometric system
WATER BASED SYSTEM
designed for the
industrial sectors that
require an ultra-low
environmental impact.
ICR launches GLADIATOR,
2K acrylic enamel with
a high quality orange
peel/textured effect.
2019
ICR SPRINT COMPOSITES | 5
10. STRUCTURAL ADHESIVES
PROPERTIES U.M. VALUE
Color - Blue color changing
Gel Time1
min 60 ± 6
Fixture Time2
hours 10
Specific weight Kg/l 1.05 ± 0.05
CERTIFICATION
PACKAGING
STORAGE
NOTES
HARDENERS
CATALYSIS RATIO
GENERAL FEATURES
X10 Extreme Structural Adhesive / L has obtained the RINA
certification (Italian Naval Registry) as a structural adhesive.
Certificate N° DIP075318CS issued on 09/9/2018.
X10 is supplied in:
- 15 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C,
must not be exposed to heat sources or sunlight. In these conditions
the product will remain stable for 1 year from the date of shipment.
Application should be carried out at temperatures above 15°C.
1
100g of product catalysed at 2% with C29, at 25°C
2
Achievement of 1.4 MPa, Lap-Shear, ASTM D1002, Instron 5582, Load Cell 100 KN, Bluehill 1.8 software, 8.3 MPa/mi
3
Brookfield, TB, Up-Down, 5 rpm, 25°C
4
Traction, ASTM D638, Instron 5582, Load Cell 100 KN, Bluehill 1.8 software, 5 mm/min
5
Internal method
6
5g catalysed at 2% with C29, 24h at 25°C and 2h at 80°C, DSC Q100 (TA Instruments), 2nd heating scan, -50°C ÷ + 200°C, 20°C/min, ISO 11357
C29 (MEK peroxide al 50%)
1-3%
SURFACE PREPARATION
THERMAL AND MECHANICAL DATA
Use V09 for degreasing and cleaning the surface in order to remove
any trace of pollutants.
Thixotropic structural adhesive based on urethane acrylate resins. Excellent structural adhesive PROPERTIES on FRP substrates
(Fiber Reinforced Polymers).
Main Features
Extraordinary elasticity and excellent fatigue resistance / Excellent chemical and physical resistance / High properties / Low exothermic peak
X10 EXTREME STRUCTURAL ADHESIVE / L
ADHESIVE FOR STRUCTURAL BONDING
PROPERTIES U.M. VALUE
Viscosity3
Pas 225 ± 15
Strain at break4
MPa 21.3 ± 2.0
Elongation at break4
% 100
Linear shrinkage5
% 0.6 ± 0.1
Shore Hardness D D 73
Tg (after 2 hours
at 80°C)6 °C 44
10 | ICR SPRINT COMPOSITES
11. STRUCTURAL ADHESIVES
PROPERTIES U.M. VALUE
Color -
Blue color
changing
Gel Time 2% M50
(MEKP 50%) at 25°C
min 60 ± 10
Gel Time 2% C08
(CEP) at 25°C
min 65 ± 10
Specific weight Kg/l 1.40 - 0.10
PROPERTIES U.M. VALUE
Deformation % 17
Strain at break MPa 8.5
Linear shrinkage % 0.2
Tg °C 71
HARDENERS CATALYSIS RATIO
M50 (MEK 50%) 1-3%
RECOMMENDED USES
GENERAL FEATURES
STORAGE
NOTESSURFACE PREPARATION
THERMAL AND MECHANICAL DATA
PACKAGING
Recommended for FRP (Fibre Reinforced Polymers) structures and
metals, such as steel, aluminum and light alloys.
It is used in sectors like marine, railways, truck industry, etc. Thanks
to its capacity of deformation, it favours the structural adjustment,
counteracting delamination/cracking problems in the bonding points.
P40 has high bond strength, excellent flexibility, high mechanical
properties (see table), low linear shrinkage, good chemical and
physical resistance. It is suitable for mechanical application.
Store in original sealed packaging, at temperatures below 20°C,
must not be exposed to heat sources or sunlight. In these conditions
the product will remain stable for 4 months from the date of shipment.
Application should be carried out at temperatures above 15°C.Degrease and clean the surface with V09, in order to remove traces
of pollutants and sand.
P40 is supplied in:
250 kg drums (net weight)
Structural adhesive based on special vinylester resin, with excellent mechanical properties, like flexibility and adhesion power.
Suitable for adhesion with FRP, metals (steel, aluminum, light allows).
Main Features
White color / Easy to sand / Very good chemical resistance
POLIFIBRE STRUCTURAL VE
VINYLESTER FLEX PUTTY P40
ICR SPRINT COMPOSITES | 11
14. POLYESTER ADHESIVES
P23 filler bonder with C08 Liquid Hardener
PROPERTIES U.M. VALUE
Color -
Blue color
changing
Gel Time min 60 ± 20
Specific weight Kg/l 1.45 ± 0.05
Linear shrinkage1
% 0.4
Shore Hardness D D 73
Tg (after 2 hours
at 80°C)2 °C 72
HDT (after 2 hours
at 80°C)3 °C 67
Tensile modulus of
elasticity4 MPa 1930
POLIFIBRE SOFT
SOFT LOW SHRINKAGE FILLING ADHESIVE
Color-changing filler bonder made with unsaturated polyester resins and fibres.
Main Features
Shrinkage close to zero / Excellent spreadability / Elevated hardness / Good flexibility
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
P23 is a specially-formulated filler bonder for the production and
repair of fibreglass items. It is excellent when used for:
- filling edges and small-medium radius.
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P23
characteristics, measured at 20°C, are reported in the following table.
P23 is supplied in:
- 4 L tins
- 25 Kg drums (net weight)
- 250 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, ISO 527-1
P23 is a two-component filler bonder and must be mixed thoroughly
with the specific liquid hardener C08 (Cyclohexanone peroxide).
P23 bonder must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P23
14 | ICR SPRINT COMPOSITES
15. P26 filler bonder with 2% MEKP Liquid Hardener
PROPERTIES U.M. VALUE
Color - neutral
Gel Time min 65 ± 15
Specific weight Kg/l 1.50 ± 0.05
Linear shrinkage1
% 0.3
Shore Hardness D D 73
Tg (after 2 hours
at 80°C)2 °C 91
HDT (after 2 hours
at 80°C)3 °C 64
Tensile modulus of
elasticity (after 2
hours at 80°C)4
MPa 4215
Filler bonder consisting of unsaturated polyester resins and fibres.
Main Features
No vertical dripping / Excellent spreadability / Good flexibility
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P26
characteristics, measured at 20°C, are reported in the following table.
P26 filler bonder is supplied in:
- 25 Kg drums (net weight)
- 250 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, UNI EN ISO 178
P26 is a two-component filler bonder and must be mixed thoroughly
with the specific liquid hardener MEKP (methyl ethyl ketone peroxide).
P26 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
POLYESTER ADHESIVES
POLIFIBRE SOFT TX
LOW-SHRINKAGE MULTIPURPOSE BONDER
RECOMMENDED USES
P26 is a specifically-formulated filler bonder for the production and
repair of fibreglass items. It is excellent when used for:
- filling of edges and curves of medium-small radius
- assembly of fiberglass products
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P26
ICR SPRINT COMPOSITES | 15
16. POLYESTER ADHESIVES
P28 Polifibre with 2% Liquid Hardener MEKP
PROPERTIES U.M. VALUE
Color - neutral
Gel Time min 30± 5
Specific weight Kg/l 1.49 ± 0.05
Linear shrinkage1
% 0.3
Shore Hardness D D 73
Tg (after 2 hours
at 80°C)2 °C 91
HDT (after 2 hours
at 80°C)3 °C 64
Tensile modulus of
elasticity (after 2
hours at 80°C)4
MPa 4215
POLIFIBRE SOFT TX FAST
FAST LOW-SHRINKAGE MULTIPURPOSE BONDER
Adhesive-Filler based on unsaturated polyester resins and glass fibres.
Main Features
No vertical dripping / Excellent spreadability / Good flexibilty / Rapid hardening
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
P28 is specially-formulated for the production, repair and adhesion of
FRP items. It is excellent when used for:
- filling small to medium radius edges and curves
- assembly of FRP products
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P28
characteristics, measured at 20°C, are reported in the following table.
P28 is supplied in:
- 25 kg drums
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, UNI EN ISO 178
P28 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
Mix with a percentage of hardener taking the current room temperature
where it will be used into account. Never work at temperatures below
5°C.
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P28
16 | ICR SPRINT COMPOSITES
17. P30
PROPERTIES U.M. VALUE
Color - light blue
Specific weight Kg/l 1.35 ± 0.05
Elastic modulus1
MPa 2175
Adhesive with color changing, based on unsaturated polyester resins and glass microfibres.
Main Features
Suitable to mechanical application / Good adhesion / Good flexibility / Low shrinkage
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P30
characteristics, measured at 20°C, are reported in the following table.
P30 is supplied in:
- 25 Kg drums (net weight)
- 250 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
Dynamometer Test, ISO 527-1
P30 is two-component and must be mixed thoroughly with liquid or
paste hardener.
P30 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
POLYESTER ADHESIVES
POLIFIBRE MF AMC
FLUID PUTTY WITH MICROFIBRES
RECOMMENDED USES
P30 is a specially-formulated for general adhesion on fibreglass
reinforced plastic items. It is excellent when used for:
- production of FRP items
- filling edges and small medium radius
HARDENERS GEL TIME
2% (MEKP) B180 / M50 40 ± 3’
2% (BPO) Paste 18 ± 3’
P30
ICR SPRINT COMPOSITES | 17
18. POLYESTER ADHESIVES
P33 con 2% Induritore C29
PROPERTIES U.M. VALUE
Color - light blue
Gel Time min 35 ± 5
Specific weight Kg/l 1.3 ± 0.1
Linear shrinkage1
% 0.25 ± 0.1
Elastic modulus2
MPa 4796 ± 92.79
Def. at break3
% 3.21 ± 0.22
Strain at break4
MPa 32.6 ± 1.18
POLYESTER FLEX ADHESIVE
Unsaturated polyester adhesive with Viracolor, reinforced with short glass fibres.
Main Features
Easy application / High adhesive power / Low shrinkage / Good flexibility
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
Suitable for general gluing and filling corners of products in FRP. With
catalysis it takes on a soft, non-dropping consistence and an easily
malleable.
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P33
characteristics, measured at 20°C, are reported in the following table.
P33 is supplied in:
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
Internal method ICR
2;3;4
Traction ISO 527-1
Methyl ethyl ketone peroxide C29 (MEKP 50%)
It must be mixed thoroughly with a percentage of catalyst between
1 - 3%. We recommend the use of the product at temperatures above
10°C.
P33
18 | ICR SPRINT COMPOSITES
19. Reinforced putty P50 with Paste Hardener C10
PROPERTIES U.M. VALUE
Color - grey-green
Gel Time min 6
Specific weight Kg/l 1.60 ± 0.10
Linear shrinkage1
% 0.35
Shore Hardness D D 65
Min. sanding time min 40
Tg (after 2 hours
at 80°C)2 °C 97
HDT (after 2 hours
at 80°C)3 °C 82
Flexural modulus of
elasticity4 MPa 3670
Putty based on unsaturated polyester resins, reinforced with glass fibres and mineral fillers.
Main Features
Excellent workability with spatula / Excellent spreadability / Elevated hardness / Excellent mechanical strength
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P50
characteristics, measured at 20°C, are reported in the following table.
P50 is supplied in:
- 750 ml tins
- 4 L tins
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
P50 is a two-component reinforced putty which must be accurately
mixed with the specific C10 paste hardener (Dibenzoyl peroxide).
P50 mastic must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
Do not exceed these percentages. Excessive amounts of hardener can
lead to peroxide stains during the finishing phase.
POLYESTER ADHESIVES
TEX FIBREGLASS PUTTY
GENERAL PURPOSE PUTTY WITH FIBRES
RECOMMENDED USES
P50 has been formulated for assembling glass-reinforced plastic and
different materials together. It can be used in processes such as:
- positioning bulkheads when the interiors are assembled
- gluing match-moulds, walls and ceilings
- stoppering the hull and parts in fibreglass-reinforced plastic
P50
CATALYSIS AND TEMPERATURE PASTE C10 HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, UNI EN ISO 178
ICR SPRINT COMPOSITES | 19
20. POLYESTER ADHESIVES
P69 with hardener C10 Paste C08 Liquid
PROPERTIES U.M. VALUE
Color - Blue color changing
Gel Time min 4.5 ± 1.5 27 ± 5.0
Specific weight Kg/l 4.5 ± 1.5
Linear shrinkage1
% 0.950 0.950
Shore Hardness D D 78 78
Min. sanding time min 70 360
Tg (after 2 hours
at 80°C)2 °C 65 65
HDT (after 2 hours
at 80°C)3 °C 62 59
CATALYSIS AND
TEMPERATURE
C10 PASTE
HARDENER
C08 LIQUID
HARDENER
between 5 and 10°C 3.0% 3.0%
between 10 and 20°C 2.0% 2.0%
above 20°C 1.0% 1.0%
POLIERRE VIRACOLOR
FILLING PUTTY WITH FIBRES
Based on unsaturated polyester resins, glass fibres and mineral fillers.
Main Features
Excellent workability with spatula/ Elevated hardness / Good mechanical strength
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
P69 is specially-formulated for assembling of FRP items and bonding
of other materials; it is excellent when used for:
- spars and Bulkheads fixing
- assembling the structure of the model
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P69
characteristics, measured at 20°C, are reported in the following table.
P69 is supplied in:
- 4 Kg drums (net weight)
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
P69 is two-components and must be mixed thoroughly with the specific
paste hardener C10 (Benzoyl peroxide) or liquid hardener C08
(Cyclohexanone peroxide).
P69 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
If the C10 hardener is used, do not exceed these percentages.
Excessive amount of hardener can lead to peroxide stains during the
finishing phase.
P69
20 | ICR SPRINT COMPOSITES
21. REACTIVITY
% MEKP 50% T°C GEL TIME
2 22 9’ – 12’
2 15 20’ – 28’
General features with 2% MEKP Hardener Liquid 50%
PROPERTIES U.M. VALUE
Color - light blue viracolor
Specific weight Kg/l 1.57 ± 0.10
Linear shrinkage % 0.3 ± 0.1
Unsaturated polyester and mineral-based filling putty with soft consistency.
Main Features
Excellent spreadability /Easy sanding / Good flexibility
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The putty is supplied in:
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
It is a two-component putty and must be mixed thoroughly with the
specific liquid hardener methyl ethyl ketone peroxide (MEKP).
P71 must be mixed with a percentage between 1 – 3% of hardener that
takes into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
POLYESTER ADHESIVES
POLYESTER PUTTY WITH FIBRES
FILLING PUTTY FOR LEVELLING
RECOMMENDED USES
It is a putty formulated for filling / levelling and repairing fibreglass
and metal surfaces which are not submerged, where higher than the
normal thicknesses provided by common putties are required. The
optimum balance of its features allows the repair of wide surfaces,
for thicknesses up to 4mm. After sanding, the levelled application of
autobody / nautical putty is recommended before successive jobs.
P71
ICR SPRINT COMPOSITES | 21
22. POLYESTER ADHESIVES
P73 Bonder filler C10 Paste C08 Liquid
PROPERTIES U.M. VALUE
Color - light blue
Gel Time min 4.5 ± 1.5 27 ± 5.0
Specific weight Kg/l 1.70 ± 0.10
Linear shrinkage1
% 0.950 0.790
Shore Hardness D D 78 78
Min. sanding time min 70 360
Tg (after 2 hours
at 80°C)2 °C 65 66
HDT (after 2 hours
at 80°C)3 °C 62 59
CATALYSIS AND
TEMPERATURE
C10 PASTE
HARDENER
C08 LIQUID
HARDENER
between 5 and 10°C 3.0% 3.0%
between 10 and 20°C 2.0% 2.0%
above 20°C 1.0% 1.0%
POLIERRE VIRACOLOR SOFT
SOFT FILLING MULTIPURPOSE PUTTY
Color-changing unsaturated polyester-based filling bonder, reinforced with special microfibres and lamellar fillers.
Main Features
High softness / Notable hardness / Good mechanical resistance / Brush appliable
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
P73 is ideal for the assembly of fibreglass items for the adhesion of
various materials, and for small fillings.
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P73
characteristics, measured at 20°C, are reported in the following table.
P73 is supplied in:
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
Internal method
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
P73 is a two-component filler bonder and must be accurately mixed
with the specific hardener paste C10 (benzoyl peroxide) or liquid
hardener C08 (cyclohexanone peroxide), or liquid MEKP 50%.
P73 mastic must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
In the case of using C10 Hardener, do not exceed the stated
percentages. Excessive hardener can cause peroxide staining in the
finishing stage.
P73
22 | ICR SPRINT COMPOSITES
26. VINYLESTER ADHESIVES
P13 with 2% MEKP
PROPERTIES U.M. VALUE
Color -
olive green
viracolor
Specific weight Kg/l 1.5 ± 0.1
Tg (after 2 hours
at 80°C)1 °C 78
Linear shrinkage2
% 0.9 ± 0.1
HDT (after 2 hours
at 80°C)3 °C 74.5
Tensile modulus of
elasticity4 MPa 1546 ± 110
FILLING ADHESIVE VE AMC
FLUID VINYLESTER ADHESIVE
Adhesive-Filler with color changing, based on unsaturated polyester resins.
Main Features
Suitable for machine application / High adhesive power/ Chemical and osmosis resistance / Good flexibility
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
P13 is excellent when used for:
- general bonding of FRP items
- filling edges and small medium curves
- repairing of damaged surfaces
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P13
characteristics, measured at 25°C, are reported in the following table.
P13 is supplied in:
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
1
DSC Test at 20°C/min under N2
, ISO 11357
1
After 2 h at 80°C
3
DMA Test, ASTM D648-01
4
Dynamometer Test, ISO 527-1
P13 is two-component and must be mixed thoroughly with liquid
hardeners.
P13 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
HARDENERS GEL TIME
2% (MEKP) B180/ M50 35’ ± 5’
2% (CEP) C08 60’± 10’
P13
26 | ICR SPRINT COMPOSITES
27. P14 con 2% di MEKP
PROPERTIES U.M. VALUE
Color - olive green
Specific weight Kg/l 1.5 ± 0.1
Tg (after 2 hours
at 80°C)1 °C 89
HDT (after 2 hours
at 80°C)2 °C 87
Linear shrinkage3
% 0.6 ± 0.2
Tensile modulus of
elasticity4 MPa 3844
Adhesive-Filler with color-changing, based on vinylester resins, reinforced with glass microfibres.
Soft look, does not undergo rheological modification with hardening.
Main Features
Suitable for machine application / High adhesive power/ Chemical and osmosis resistance /
No vertical dripping / Low shrinkage / Good flexibilty
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P14
characteristics, measured at 20°C, are reported in the following table.
P14 is supplied in:
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
Mix accurately with liquid hardener (MEKP 50%).
P14 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
VINYLESTER ADHESIVES
ADHESIVE WITH FIBRES VE
VINYLESTER ADHESIVE WITH FIBRES
RECOMMENDED USES
For general adhesion on FRP. It is excellent when used for:
- general glueing of FRP parts
- filling edges and medium radius curves
- repairing damaged surfaces
HARDENERS GEL TIME
2% (MEKP) B180/ M50 22 ± 2’
P14
1
DSC Test at 20°C/min under N2
, ISO 11357
2
DMA Test, ASTM D648-01
3
After 2 h at 80°C
4
Dynamometer Test, UNI EN ISO 178
ICR SPRINT COMPOSITES | 27
28. VINYLESTER ADHESIVES
P15 with 2% MEKP
PROPERTIES U.M. VALUE
Color - olive green
Specific weight Kg/l 1.5 ± 0.1
Tg (after 2 hours
at 80°C)1 °C 89
HDT (after 2 hours
at 80°C)2 °C 87
Linear shrinkage3
% 0.6 ± 0.2
Tensile modulus of
elasticity4 MPa 3844
ADHESIVE WITH FIBRES VE FAST
FAST VINYLESTER ADHESIVE WITH FIBRES
Adhesive with color-changing, based on vinylester resin with glass fibres, for glueing and filling.
P15 does not undergo rheological deformation with hardening.
Main Features
Suitable for machine application / High adhesive power / Chemical and osmosis resistance /
No vertical dripping / Low shrinkage / Good flexibilty
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
For general adhesion. It is excellent when used for:
- glueing of FRP parts
- filling edges and medium radius curves
- repairing damaged surfaces
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P15
characteristics, measured at 20°C, are reported in the following table.
P15 is supplied in:
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
1
DSC Test at 20°C/min under N2
, ISO 11357
2
DMA Test, ASTM D648-01
3
After 2 h at 80°C
4
Dynamometer Test, UNI EN ISO 178
Mix accurately with liquid hardener (MEKP 50%).
P15 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
HARDENERS GEL TIME
2% (MEKP) B180/ M50 11 ± 1’
P15
28 | ICR SPRINT COMPOSITES
29. Vinylester resins reinforced with organic fibres, glassfibres (max length 3 mm) and mineral fillers.
Main Features
High resistance to osmosis / Thixotropic, no vertical dripping / High mechanical properties /
Excellent adhesion / Excellent flexibility
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P25
characteristics, measured at 20°C, are reported in the following table.
P25 is supplied in:
- 25 kg drums (net weight)
- 250 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
P25 is a two-component reinforced putty which must be accurately
mixed with the specific C08 hardener (Cyclohexanone peroxide).
P25 mastic must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
VINYLESTER ADHESIVES
POLIVIR WITH FIBRES VE
FILLING VINYLESTER PUTTY WITH FIBRES
RECOMMENDED USES
P25 is expressly formulated to repair anti-osmosis laminates. It can be
used in processes such as:
- hulls’ joining
- repairing of surfaces damaged by osmosis
- filling of small-medium radius edges and curving
P25
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
Reinforced putty P25 with Liquid Hardener C08
PROPERTIES U.M. VALUE
Color - light blue viracolor
Gel Time min 40 ± 5.0
Specific weight Kg/l 1.25 ± 0.05
Linear shrinkage1
% 0.4
Shore Hardness D D 70
Min. sanding time min 270
Tg (after 2 hours
at 80°C)2 °C 105
HDT (after 2 hours
at 80°C)3 °C 97
ICR SPRINT COMPOSITES | 29
30. VINYLESTER ADHESIVES
VINYLESTER PUTTY WITH FIBRES
FILLING VINYLESTER PUTTY FOR LEVELLING
Soft-consistancy white putty, based on vinylester resin, mineral filler, reinforced with microfibres.
Main Features
Excellent spreadability / High adhesive power / Low shrinkage / Easy sanding
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
Suitable for filling and levelling of fibreglass and metal surfaces
where higher than the normal thicknesses are required with repairs up
to 4mm. After sanding, the levelled application of VE nautical putty,
S11 or S12, is recommended before subsequent jobs.
P72 is supplied in:
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
1
DSC Test at 20°C/min under N2
, ISO 11357
2
DMA Test, ASTM D648-01
It is a two-component putty and must be mixed accurately with the
specific liquid hardener methyl ethyl ketone peroxide (MEKP 50%).
P72 must be mixed with a percentage between 1 - 2% of hardener.
Never work at temperatures below 5°C.
P72
Reactivity at 23°C, catalysis in weight
% CAT. GEL TIME SANDABLE
1 ~ 40’ > 180’
2 ~ 34’ > 130’
PROPERTIES U.M. VALUE
Color - white (Ral 9016)
Specific weight Kg/l 1.60 ± 0.10
Gel Time 26°C
2% MEKP
min 27’
Linear shrinkage % 0.2 ± 0.1
Tg (after 2 hours
at 80°C)1 °C 87
HDT (after 2 hours
at 80°C)2 °C 78
30 | ICR SPRINT COMPOSITES
34. PUTTIES
Putty S12 with Paste Hardener C10
PROPERTIES U.M. VALUE
Color - white
Gel Time min 6 ± 1
Specific weight Kg/l 1.67 ± 0.05
Linear shrinkage1
% 0.67
Shore Hardness D D 64
Min. sanding time min 15 - 30
Tg (after 2 hours
at 80°C)2 °C 103
Elastic modulus3
MPa 10672
Flexural modulus of
elasticity4 MPa 9226
GEL FILLER FOR FINISHING VE/P
VINYLESTER PUTTY FOR BODYWORK
High-performances putty based on vinylester resins and very fine mineral fillers.
Main Features
Good spreadability / Shrinkage near to zero / Elevated hardness
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
S12 is a putty formulated for filling and repairing hulls laminated with
vinylester resins; ideal for levelling and finishing hulls before the gel-
coat final touch. S12 can be used for:
- finishing hulls
- finishing aesthetic joints
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The S12
characteristics, measured at 20°C, are reported in the following table.
S12 is supplied in:
- 750 ml tins
- 4 L tins
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
Dynamometer Test, ISO 527-1
4
Dynamometer Test, UNI EN ISO 178
S12 is a two-component putty which must be accurately mixed with the
specific C10 paste hardener (Dibenzoyl Peroxide).
S12 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
Do not exceed these percentages. Excessive amounts of hardener can
lead to peroxide stains during the finishing phase.
CATALYSIS AND TEMPERATURE C10 PASTE HARDENER
between 5 and 10°C 2.0%
between 10 and 20°C 1.5%
above 20°C 1.0%
S12
34 | ICR SPRINT COMPOSITES
35. White Putty S14 with Liquid Hardener C08
PROPERTIES U.M. VALUE
Color - white
Gel Time min 40 ± 5
Specific weight Kg/l 1.30 ± 0.05
Linear shrinkage1
% 1.20
Shore Hardness D D 60
Min. sanding time min 120
Tg (after 2 hours
at 80°C)2 °C 67
HDT (after 2 hours
at 80°C)3 °C 54
Flexural modulus of
elasticity4 MPa 4854
Medium weight high-performances putty based on unsaturated polyester resins and very fine mineral fillers.
Main Features
White color / Easy spreadability / High resistance to chemical agents
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The S14
characteristics, measured at 20° C, are reported in the following table.
S14 is supplied in:
- 4 L tins
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
S14 is a putty formulated for finishing glass reinforced plastic panels.
S14 can be used for:
- finishing fibreglass reinforced plastic handworks
- finishing aesthetic joints
- eliminating imperfections and scratches from bodywork
Do not exceed 12-14 mm thickness (to be reached after severalcoats).
S14 putty must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
PUTTIES
GEL FILLER FOR FINISHING PE/L
HIGH PERFORMANCES POLYESTER PUTTY FOR BODYWORK
RECOMMENDED USES
S14 is a two-component putty which must be accurately mixed with
the specific C08 liquid hardener (Cyclohexanone peroxide).
S14
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 2.0%
between 10 and 20°C 1.5%
above 20°C 1.0%
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, ISO 527-1
ICR SPRINT COMPOSITES | 35
36. PUTTIES
White Putty S15 with Paste Hardener C10
PROPERTIES U.M. VALUE
Color - white
Gel Time min 3 ± 1
Specific weight Kg/l 1.30 ± 0.05
Linear shrinkage1
% 0.90
Shore Hardness D D 60
Min. sanding time min 30
Tg (after 2 hours
at 80°C)2 °C 89
HDT (after 2 hours
at 80°C)3 MPa 1067372
GEL FILLER FOR FINISHING PE/P
HIGH PERFORMANCES POLYESTER PUTTY FOR BODYWORK
Medium weight high-performances putty based on unsaturated polyester resins and very fine mineral fillers.
Main Features
White color / Easy spreadability / High resistance to chemical agents
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
S15 is a putty formulated for finishing fibreglass surfaces.
S15 can be used for:
- finishing fibreglass handworks
- eliminating imperfections and scratches from bodywork
Do not exceed 6-8 mm thickness (to be reached after several coats).
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The S15
characteristics, measured at 20°C, are reported in the following table.
S15 is supplied in:
- 750 ml tins
- 4 L tins
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
S15 is a two-component putty which must be accurately mixed with the
specific C10 paste hardener (Dibenzoyl Peroxide).
S15 putty must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
Do not exceed these percentages. Excessive amounts of hardener can
lead to peroxide stains during the finishing phase.
CATALYSIS AND TEMPERATURE C10 PASTE HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
S15
36 | ICR SPRINT COMPOSITES
37. S22 with 2% Paste Hardener C10
PROPERTIES U.M. VALUE
Color - white
Gel Time min 4 ± 1
Specific weight Kg/l 1.95 ± 0.05
Linear shrinkage1
% 0.61
Shore Hardness D D 57
Min. sanding time min 40
Tg (after 2 hours
at 80°C)2 °C 80
HDT (after 2 hours
at 80°C)3 °C 78
High-performance putty, based on unsaturated polyester resins and mineral fillers.
Main Features
White color / Easy spreadability / High resistance to chemical agents
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The S22
characteristics, measured at 20°C, are reported in the following table.
S22 is supplied in
- 750 ml tins
- 4 L tins
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
S22 is two-components, which must be accurately mixed with the
specific C10 paste hardener (BPO).
S22 putty must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
PUTTIES
EASY TOP WHITE
WHITE POLYESTER PUTTY
RECOMMENDED USES
S22 is a putty formulated for finishing wood and FRP parts; it can be
used for:
- shaping models with by spatula
- finishing FRP parts
- finishing aesthetic FRP joints
S22
CATALYSIS AND TEMPERATURE C10 PASTE HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
ICR SPRINT COMPOSITES | 37
38. PUTTIES
Grey Putty S71 with Paste Hardener C10
PROPERTIES U.M. VALUE
Color - grey
Gel Time min 4 ± 1
Specific weight Kg/l 1.97 ± 0.05
Linear shrinkage1
% 1.22
Shore Hardness D D 57
Min. sanding time min 40
Tg (after 2 hours
at 80°C)2 °C 69
HDT (after 2 hours
at 80°C)3 °C 69
EASY TOP PUTTY GREY
MULTIPURPOSE GREY PUTTY
High-performances putty based on unsaturated polyester resins and very fine mineral fillers.
Main Features
Grey color / Easy spreadability / High resistance to chemical agents
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
S71 is a putty formulated for the use on different surfaces such as
wood and fibreglass. S71 can be used for:
- models shaping
- finishing of fibreglass handworks
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The S71
characteristics, measured at 20°C, are reported in the following table.
S71 is supplied in:
- 750 ml tins
- 4 L tins
- 25 kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
S71 is a two-component putty which must be accurately mixed with the
specific C10 paste hardener (Dibenzoyl Peroxide).
S71 putty must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
Do not exceed these percentages. Excessive amounts of hardener can
lead to peroxide stains during the finishing phase.
CATALYSIS AND TEMPERATURE C10 PASTE HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
S71
38 | ICR SPRINT COMPOSITES
42. POLIBONDERS
Light Bonder P01 with 2% Liquid Hardener C08
PROPERTIES U.M. VALUE
Color - light blue viracolor
Gel Time min 75 ± 25
Specific weight Kg/l 1.0 ± 0.1
Linear shrinkage1
% 0.5
Shore Hardness D D 60
Tg (after 2 hours
at 80°C)2 °C 78
HDT (after 2 hours
at 80°C)3 °C 76
Tensile elastic
modulus (after 2
hours at 80°C)4
MPa 5486
POLIBONDER SOFT LIGHT
LIGHT BONDER FOR PANELS
Special bonder based on unsaturated polyester resins, with light reinforcing filler and micro-spheres.
Main Features
Light, specific weight (1.0 kg/l) / Excellent spreadability / High adhesive power
RECOMMENDED USES GENERAL FEATURES
PACKAGINGYIELD
STORAGE
HARDENERS
CATALYSIS RATIO
P01 is a bonder formulated for gluing core materials and fibreglass
panels. The high adhesive power and low weight are the main
characteristics. It can be used for:
- bonding expanded PVC components
- bonding panels made of balsa and termanto
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P01
characteristics, measured at 20°C, are reported in the following table.
P01 is supplied in:
- 15 Kg drums (net weight)
- 175 Kg drums (net weight)
1.5 L/m2
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
Post-curing: 48 h r.t.
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, ISO 527-1
P01 is a two-component bonder which must be accurately mixed with
the specific C08 liquid hardener (Cyclohexanone peroxide).
P01 bonder must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P01
BONDING OF THEREX
ON FIBERGLASS
WITH FOAM BONDER
42 | ICR SPRINT COMPOSITES
43. P02 light bonder with C08 Liquid Hardener
PROPERTIES U.M. VALUE
Color - light blue viracolor
Gel Time min 120 ± 25
Specific weight Kg/l 1.0 ± 0.1
Linear shrinkage1
% 0.5
Shore Hardness D D 60
Tg (after 2 hours
at 80°C)2 °C 78
HDT (after 2 hours
at 80°C)3 °C 76
Tensile elastic
modulus (after 2
hours at 80°C)4
MPa 3552
Special bonder based on unsaturated polyester resins, light fillers and micro-spheres.
Main Features
Light, specific weight (1.0 kg/l) / Excellent spreadability / High adhesive power / Suitable to mechanical application
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P02
characteristics, measured at 20° C, are reported in the following table.
P02 is supplied in:
- 15 Kg drums (net weight)
- 175 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
Value refers to sample with 2% C08 liquid hardener post-hardened 2 hours at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
4
Dynamometer Test, ISO 527-1
P02 is a two-components bonder and must be mixed thoroughly with
the specific liquid hardener C08 (Cyclohexanone peroxide).
P02 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
POLIBONDERS
POLIBONDER SOFT LIGHT AMC
FLUID BONDER FOR PANELS
RECOMMENDED USES
P02 is a specially-formulated bonder for the adhesion of core
material, for structural sandwiches where limited weight and high
adhesion capacity are essential requirements for quality application.
It is excellent when used for:
- gluing PVC foams and other core materials
P02
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 25°C 2.0%
above 20°C 1.0%
ICR SPRINT COMPOSITES | 43
44. POLIBONDERS
Ultra-Light weight Border P07 with Liquid Hardener C08
PROPERTIES U.M. VALUE
Color - white
Gel Time a 20°C min 40 ± 10
Specific weight Kg/l 0.67 ± 0.03
Linear shrinkage1
% 1.06
Shore Hardness D D 60
Tg (after 2 hours
at 80°C)2 °C 63
HDT (after 2 hours
at 80°C)3 °C 47
ULTRA LIGHT POLIBONDER
LIGHTWEIGHT PANEL BONDER
Special bonder consisting of unsaturated polyester resins, with ultra lightweight reinforcement components and micro-spheres.
Main Features
Ultra lightweight (specific weight of 0.7 kg/l) / Excellent spreadability / High adhesive power
RECOMMENDED USES GENERAL FEATURES
PACKAGING
YIELD
STORAGE
HARDENERS
CATALYSIS RATIO
P07 is a bonder formulated for gluing core materials. The high adhesive
power and low weight are the main characteristics for guaranteeing
the quality of application. It can be used for:
- bonding expanded PVC components
- bonding panels made of balsa and termanto
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P07
characteristics, measured at 20°C, are reported in the following table.
P07 is supplied in:
- 10 Kg drums (net weight)
- 135 Kg drums (net weight)
1.5 L/m2
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
P07 is a two-component filler bonder and must be mixed thoroughly
with the specific liquid hardener C08 (Cyclohexanone peroxide).
P07 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P07
44 | ICR SPRINT COMPOSITES
45. Light Border P11 with Liquid Hardener MEKP
PROPERTIES U.M. VALUE
Color - light blue viracolor
Gel Time1
min 50 ± 10
Specific weight Kg/l 1.00 ± 0.03
Linear shrinkage2
% 0.60
Water absorption3
% 0.7
Tg (after 2 hours
at 80°C)4 °C 100
HDT (after 2 hours
at 80°C)5 °C 85
Tensile strain
at break6 % 1.4
Special bonder based on unsaturated vinylester resins, with light reinforcing filler and micro-spheres.
Main Features
Light-weight / Excellent resistance to high temperature / Excellent spreadability / High adhesive power
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P11
characteristics, measured at 20° C, are reported in the following table.
P11 is supplied in:
- 15 Kg drums (net weight)
- 175 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 4 months from the date of shipment.
1
Gel time 20°C 60 ± 10 min. with 2% hardener C08
2
After 2 h at 80°C
3
UNI EN ISO 62
4
DSC Test at 20°C/min under N2
, ISO 11357
5
DMA Test, ASTM D648-01
6
Dynamometer Test, ISO 527-1
P11 is a two-component bonder which must be accurately mixed with
the specific liquid hardener (MEKP Methylethylketone peroxide).
P11 bonder must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
POLIBONDERS
POLIBONDER LIGHT VE
LIGHT VINYLESTER BONDER FOR PANELS
RECOMMENDED USES
P11 is a bonder formulated for gluing core materials and fibreglass
panels. The high adhesive power and low weight are the main
characteristics. It can be used for:
- bonding expanded PVC components
- bonding panels made of balsa and termanto
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P11
ICR SPRINT COMPOSITES | 45
46. POLIBONDERS
Border P24 with Liquid Hardener C08
PROPERTIES U.M. VALUE
Color - light blue viracolor
Gel Time a 20°C min 40 ± 10
Specific weight Kg/l 1.49 ± 0.05
Linear shrinkage1
% 0.35
Shore Hardness D D 70
Tg (after 2 hours
at 80°C)2 °C 78
HDT (after 2 hours
at 80°C)3 °C 74
POLIBONDER SOFT
GENERAL PURPOSE BONDER
Color-changing bonder based on unsaturated polyester resins, suitable for many conditions in which fibreglass reinforced plastic parts are glued
together.
Main Features
Excellent spreadability / Elevated hardness / Shrinkage near to zero
RECOMMENDED USES GENERAL FEATURES
PACKAGING
YIELD
STORAGE
HARDENERS
CATALYSIS RATIO
P24 is a bonder especially formulated for gluing parts of fibreglass
and other materials, where use of medium-light products is advisable.
It can be used for:
- gluing core materials of a medium and small size
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The P24
characteristics, measured at 20°C, are reported in the following table.
P24 is supplied in:
- 25 Kg drums (net weight)
- 250 Kg drums (net weight)
1.5 L/m2
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 1 year from the date of shipment.
1
After 2 h at 80°C
2
DSC Test at 20°C/min under N2
, ISO 11357
3
DMA Test, ASTM D648-01
P24 is a two-component bonder which must be accurately mixed with
the specific C08 liquid hardener (Cyclohexanone peroxide).
P24 bonder must be mixed with a percentage of hardener that takes
into account the ambient temperature, in which the processing is
carried out. Do not use the product at temperatures below 5°C.
CATALYSIS AND TEMPERATURE C08 LIQUID HARDENER
between 5 and 10°C 3.0%
between 10 and 20°C 2.0%
above 20°C 1.0%
P24
46 | ICR SPRINT COMPOSITES
50. GEL COAT
PROPERTIES U.M. VALUE
Color - white and grey
Dry residue
(White)
% 80 ± 2
Dry residue
(Grey)
% 76 ± 2
Gel time at 25°C
(White)1 min 8’50’’
Gel time at 25°C
(Grey)1 min 12’50’’
Peak °C 140 ± 10
Specific weight
(White)
Kg/l 1.57 ± 0.1
Specific weight
(Grey)
Kg/l 1.43 ± 0.1
Barcol ASTM
D 2583
>40
Shore D 84 - 86
PROPERTIES U.M. VALUE
Color - white and grey
Dry residue % 72 ± 2
Gel time at 20°C1
min 10’ ± 2’
Peak1
°C 150 ± 10
Specific weight Kg/l 1.4 ± 0.1
Barcol ASTM
D 2583
>40
INDUSTRIAL TOP COAT
PARAFFINED INDUSTRIAL TOP COAT
Based on orthophthalic resin and mineral fillers.
Main Features
Good coverage / Easy application / Excellent gloss
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
Industrial gel coats due to their composition, they are particularly
suited as topcoats for indoor parts or in applications that require
subsequent sanding and / or painting.
Furthermore, they can be used when no specific chemical resistance
requests are needed. They can be supplied in the self-releasing
version, to facilitate demoulding operations, or paraffined, to improve
superficial curing when used directly on final pieces.
Using the brush
Using Spray
G1A is supplied in:
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 3 months from the date of shipment.
1
On 100 g, 2% catalysis with MEKP in adiabatic
Traditional MEKP.
Mix carefully with MKP with catalyst percentage between 1.5% - 2%.
For the application it is recommended to check the temperature of the
product, molds and the environment, which must be between 18°C
and 25°C.
G1A
50 | ICR SPRINT COMPOSITES
51. PROPERTIES U.M. VALUE
Color - white and grey
Dry residue
(White)
% 80 ± 2
Dry residue
(Grey)
% 76 ± 2
Gel time at 25°C
(White)1 min 8’50’’
Gel time at 25°C
(Grey)1 min 12’50’’
Peak °C 140 ± 10
Specific weight
(White)
Kg/l 1.57 ± 0.1
Specific weight
(Grey)
Kg/l 1.43 ± 0.1
Barcol ASTM
D 2583
>40
Shore D 84 - 86
PROPERTIES U.M. VALUE
Color - white and grey
Dry residue % 72 ± 2
Gel time at 20°C1
min 10’ ± 2’
Peak1
°C 150 ± 10
Specific weight Kg/l 1.4 ± 0.1
Barcol ASTM
D 2583
>40
Based on orthophthalic resin and mineral fillers.
Main Features
Good coverage / Easy application / Excellent gloss
RECOMMENDED USES GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
Industrial gel coats due to their composition, they are particularly
suited as topcoats for indoor parts or in applications that require
subsequent sanding and / or painting.
Furthermore, they can be used when no specific chemical resistance
requests are needed. They can be supplied in the self-releasing
version, to facilitate demoulding operations, or paraffined, to improve
superficial curing when used directly on final pieces.
Using the brush
Using Spray
G1B is supplied in:
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 3 months from the date of shipment.
1
On 100 g, 2% catalysis with MEKP in adiabatic
Traditional MEKP.
Mix carefully with MKP with catalyst percentage between 1.5% - 2%.
For the application it is recommended to check the temperature of the
product, molds and the environment, which must be between 18°C
and 25°C.
GEL COAT
INDUSTRIAL GEL COAT
INDUSTRIAL GEL COAT G1B
ICR SPRINT COMPOSITES | 51
54. MILLABLE COMPOUNDS
PROPERTIES U.M. VALUE
Usage ratio - 1:1 w/w o v/v
Pot-life1
min 30
Maximum
applicable thickness
mm 30
Time before milling2
h 24
PROPERTIES U.M. VALUE
Time to peak1
min 70
Exothermic Peak1
°C 53
Tg2
°C 47
Hardness3
Shore-D 51-54
Hardness4
Shore-D 51-54
Linear shrinkage5
% 0.25
Compressive stress
at break6 MPa > 37
PROPERTIES U.M. VALUE
Color - blue-green
Specific weight Kg/l ≈ 0,60
Use ratio - 1:1 w/w o v/v
EPOXY
MILLABLE COMPOUND
Epoxy thixotropic paste, specifically for modelling surfaces with numerical controlled milling of wood, fibreglass, polyurethane foam
and polystyrene. Easy application. Allows thin to high thicknesses with even and rapid hardening.
Main Features
Applicable in high thickness, up to a maximum of 30 mm / Low and controlled heat production / High degree of cross-linkage within 24 h /
Easy application and Easy CNC machine milling with low dust emission
RECOMMENDED USES APPLICATION PARAMETERS
PACKAGING
PRECAUTIONS
STORAGE
CHEMICAL-PHYSICAL PROPERTIES
THERMAL AND MECHANICAL DATA
- small and large scale modelling industries
- modelling for nautical, windturbine and general composite sectors
PE6 Epoxy millable compound is supplied in:
- 116 Kg drums (net weight)
The temperature of the materials and of the environment must not be
below 18°C. Do not apply thicknesses over 30 mm in a single layer.
Thicknesses over 30 mm are achieved with more applications, leaving
the first layer to harden.
Store in original sealed packaging, at temperatures between 15
and 35°C. must not be exposed to heat sources or sunlight. In these
conditions the product will remain stable for 2 years from the date of
shipment.
1
On 60 g 25 °C adiabatic container
2
After 7 days rt, DSC Q100 (TA Instruments), 2°heating scan, -50°C ÷ +180 °C, 20 °C/min, ISO 11357
3
After 7 days rt
4
After 14h a 52 °C
5
Internal method, after 14h at 52 °C
6
After 14h at 52 °C, Instron 5582, ISO 604, cell 100 KN, compression speed 0.6 mm/min
PE6
54 | ICR SPRINT COMPOSITES
55. PROPERTIES U.M. VALUE
Color - light yellow
Specific weight Kg/l ≈ 0,60
Use ratio - 1:1 w/w o v/v
Hardener for Epoxy thixotropic paste, specifically for modelling surfaces with numerical controlled milling of wood, fibreglass,
polyurethane foam and polystyrene. Easy application. Allows thin to high thicknesses with even and rapid hardening.
Main Features
Applicable in high thickness, up to a maximum of 30 mm / Low and controlled heat production /
High degree of cross-linkage within 24 hr / Easy application and easy CNC machine milling with low dust emission
PACKAGING
PRECAUTIONS
STORAGE
CHEMICAL-PHYSICAL PROPERTIES
CE6 Hardener is supplied in
- 116 Kg drums (net weight)
The temperature of the materials and of the environment must not be
below 18°C. Do not apply thicknesses over 30 mm in a single layer.
Thicknesses over 30 mm are achieved with more applications, leaving
the first layer to harden.
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
MILLABLE COMPOUNDS
HARDENER
FOR EPOXY MILLABLE COMPOUND
RECOMMENDED USES
- small and large scale modelling industries
- modelling for nautical, windturbine and general composite sectors
CE6
ICR SPRINT COMPOSITES | 55
56. Orthophthalic polyester resin with low styrene content and a methacrylic monomer, specific for lamination on expanded polystyrene before
millable pastes application.
Main Features
Low styrene content
RECOMMENDED USES
PACKAGING
STORAGE
RI1 is used in modeling for the nautical, wind and water sectors and
in general composites.
RI100 Hardener is supplied in:
- 225 Kg drums (net weight)
RI120 Hardener is supplied in:
- 20 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20 ° C,
must not be exposed to heat sources or sunlight. In these conditions
the product will remain stable for 6 months from the date of shipment.
RI1
MILLABLE COMPOUNDS
1
On 100 g, catalysis at 2% with MEKP Ketanox B180, at 23°C in an adiabatic container
2
20°C in original container closed in the dark
PROPERTIES U.M. VALUE
Color -
transparent straw
yellow
Specific weight Kg/l 1.15 ± 0.05
PROPERTIES U.M. VALUE
Exothermic peak1
°C 140 ± 10
Time to peak1
min 30 ± 5
Viscosity at 25°C cps 800 ± 200
Gel-time1
min 20 ± 5
Dry residue % 70 ± 3
Stability2
months 6
CHEMICAL-PHYSICAL PROPERTIES
THERMAL AND MECHANICAL DATA
HARDENERS
CATALYSIS RATIO
Traditional MEKP
1-3% with MEKP at 50%
RESIN FOR POLYSTYRENE IMPREGNATION
56 | ICR SPRINT COMPOSITES
57. PROPERTIES U.M. VALUE
Color - blue color changing
Specific weight Kg/l 0.95 ± 0.05
PROPERTIES U.M. VALUE
Minimum time of
milling
hours 16 - 24
Minimum thickness
applicable
mm 20 25
PROPERTIES U.M. VALUE
Exothermic peak1
°C 45 - 50
Time to peak1
min 160 - 220
Withdrawal2
% 0.3 - 0.5
Hardness3
Shore-D 57 - 63
HDT4
°C 45 - 50
Viscosity5
Pas 2500 - 3000
Flexural modulus of
elasticity6 MPa 660 ± 160
Strain at flexion
break6 MPa 9.30 ± 1
Deformation
at flexion break6 % 20 ± 1
Thixotropic polyester pastes, specific for surface modeling by milling numerically controlled on wooden,
fiberglass, polyurethane foam and protected polystyrene supports.
Main Features
Applicable in high thicknesses up to a maximum of 25 mm / Low and controlled exothermic /
High degree of cross-linking in 24h / Easy application / Easily milled with CNC machines with low dust emission
CHEMICAL-PHYSICAL PROPERTIES
APPLICATION PARAMETERS
THERMAL AND MECHANICAL DATA
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
PP1 Hardener is supplied in:
- 175 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C,
must not be exposed to heat sources or sunlight. In these conditions
the product will remain stable for 1 year from the date of shipment.
1
On 100 grams, 2% catalysis with C08,
at 23°C in an adiabatic container
2
Internal method ICR, tray 20 cm, 24h rt + 2h at 65°C,
catalysis 2% with C08
3
Catalysis 2% with C08, 24h rt + 2h at 65°C
4
ASTM D648-01, Catalysis at 2% with C08, 24h rt +
2h at 65°C
5
Brookfield, TC impeller, speed 1, 23°C
6
ISO 178, Catalysis at 2% with C08, 24h rt + 2h at 65°C
7
23°C
C08
1-3% with C08
MILLABLE POLYESTER PASTE
RECOMMENDED USES
- small and large industrial modeling
- modeling for the nautical, wind and general composite sectors
PP1
MILLABLE COMPOUNDS
ICR SPRINT COMPOSITES | 57
60. PRIMERS
HP018 CARBON LOOK PRIMER
2K TRANSPARENT PRIMER FOR CARBON FIBRES
Transparent acrylic primer with high filler power ideal for paint cycles.
Main Features
It is ideal to fill the imperfections that can characterize carbon fibre surfaces / Fast drying
RECOMMENDED USES SPRAY APPLICATION
TECHNICAL RECOMMENDATIONS
PACKAGING
STORAGE
CATALYSIS RATIO
FAF03 HP018 is a transparent acrylic primer formulated for the filling
of defects (tiny holes) in carbon fibre fabrics. The very fast drying
allows the quick application of 2-3 coats.
FAF03 hardener is supplied in:
- 5 Kg drums (net weight)
- 20 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
FAF03
HARDENERS
SM1 is a primer which must be accurately mixed with the specific
CP003 hardener and DP001 thinner.
PRODUCT WEIGHT
FAF03 HP018 2K Primer 1.000 Kg
CP003 Hardener 300
DP001/2/3 Thinner 100-200
CATALYSIS LIQUID HARDENER
30% CP003
10 - 20% DP001
Application viscosity 25-30 s
Nozzle diameter 1.7 mm
Air pressure 2-3 bar
Flash-off at 20°C 15-20 min
Recommended final
thickness (2-3 coats)
40-80 μm
Theoretic yield 9 mq/kg
Air drying 12-14 hours
Stove drying at 50°C 60 min
60 | ICR SPRINT COMPOSITES
61. Spray filler based on unsaturated polyester resins and mineral fillers.
Main Features
Allows high thickness, to be reached after several coats / Fast drying / Polishable
PRIMERS
SPRAY FILLER GREY
POLYESTER SPRAY FILLER F18
F18 polyester spray filler with C12 liquid hardener
PROPERTIES U.M. VALUE
Color - grey
Gel Time a 20°C min 20 ± 8
Specific weight Kg/l 1.60 ± 0.10
Min. sanding time min 180
GENERAL FEATURES
PACKAGING
STORAGE
HARDENERS
CATALYSIS RATIO
DILUTION
The applied product, it will take on specific properties according to
the type of hardener used and the processing temperature. The F18
characteristics, measured at 20°C, are reported in the following table.
F18 hardener is supplied in:
- 3 L tins
- 25 Kg drums (net weight)
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
F18 is a specially-formulated spray filler used as a topcoat for a variety
of surfaces. It is excellent when used for:
- a model-making topcoat
F18 must be mixed with a percentage of hardener that takes into
account the ambient temperature, in which the processing is carried
out. Do not use the product at temperatures below 5°C.
If necessary dilute with D12 Spray Thinner for polyester or pure
acetone max 5%.
RECOMMENDED USES
F18 is a two-component filler and must be mixed thoroughly with the
specific C12 liquid hardener (Cyclohexanone peroxide).
CATALYSIS LIQUID HARDENER
5% C12
ICR SPRINT COMPOSITES | 61
64. RUBBING COMPOUNDS
MORDANT RUBBING
COMPOUND FOR GELCOAT
Stabilized emulsion in combination with special abrasives with controlled granulometry. LPMO mordant - LPME extra mordant.
Main Features
High mordant power. Removes sanding marks or scratches of medium depth / high viscosity, allows very hard surfaces to be quickly polished /
Special formula for processes on gelcoat
RECOMMENDED USES PHYSICAL PROPERTIES
THINNING
PACKAGING
CHEMICAL COMPOSITION
STORAGE
POLISHING PROCESS
LPM is a compound formulated for compounding gelcoat panels. Due
to its mordanting characteristics, LPM compound can be used for:
- polishing handworks
- polishing moulds and plugs
White color
Specific weight 1.65 ± 0.10 kg/l
Due to its viscosity, the compound may need thinning.
Use petroleum.
LPM compound is supplied in:
- 2 L tins
- Special paraffins
- Emulsifiers
- Aliphatic solvents
- Silica-free abrasives in aluminium oxide
- Make sure that the gelcoat is cold before polishing.
- Remove impurities such as dirt or grease from the gelcoat with a cloth
soaked in soap and water.
- Place a small quantity of paste on a wool or foam polishing pad.
- Spread the paste evenly over the surface, with the polisher still off.
- Switch on the polisher and adjust the speed to between 800 and
1.500 rpm.
- Start polishing by exercising a light pressure, then progressively
reduce it until the paste begins to dry.
- Make several crossed runs in order to remove all the scratches. Do
not polish in the same area for very long or the surface will become
overheated.
This process will achieve a finish high level of gloss which can be
improved if required by a successive treatment with polishing
compound.
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
LPM/LPMO/LPME
64 | ICR SPRINT COMPOSITES
65. RECOMMENDED USES PHYSICAL PROPERTIES
THINNING
PACKAGING
CHEMICAL COMPOSITION
STORAGE
POLISHING PROCESS
LPN2 is a polishing compound formulated for polishing gelcoat and
fibreglass panels. It can therefore be used to advantage for:
- polishing handworks
- polishing moulds
White color
Specific weight 1.78 ± 0.10 kg/l
Owing to its viscosity, the abrasive paste may need thinning.
Use petroleum.
LPN2 is supplied in:
- 2 L tins
- Esterificated waxes
- Emulsifiers
- Aliphatic solvents
- Polishing abrasives
- Make sure that the gelcoat is cold before polishing.
- Remove impurities such as dirt or grease from the gelcoat with a cloth
soaked in soap and water.
- Place a small quantity of paste on a wool or foam polishing pad.
- Spread the paste evenly over the surface, with the polisher still off.
- Switch on the polisher and adjust the speed to between 1.500 and
2.000 rpm.
- Start polishing by exercising a light pressure, then progressively
reduce it until the paste begins to dry.
- Make several crossed runs in order to remove all the scratches. Do
not polish in the same area for very long or the surface will become
overheated.
This process will achieve a finish high level of gloss which can be
improved if required by a successive treatment with polishing
compound.
Store in original sealed packaging, at temperatures below 20°C, must
not be exposed to heat sources or sunlight. In these conditions the
product will remain stable for 2 years from the date of shipment.
Stabilized highly polishing emulsion in combination with special abrasives with fine granulometry.
Main Features
Provides the utmost gloss thanks to the special mixture of esterificated waxes / Removes sanding marks or low depth scratches
RUBBING COMPOUNDS
POLISHING RUBBING
COMPOUND LPN2
ICR SPRINT COMPOSITES | 65
66. ON-DEMAND PRODUCTS
Vinylester putty S1122009M1 White
Polyester putty S1622009M1 White
Polyester putty S1822009M1 White
Polyester putty S2722009M1 Light Yellow
Polyester putty S9722009M1 Yellow
Polyester adhesive P2122009M1
Polyester adhesive P5222009M1
Polyester adhesive P5322009M1
These products are available upon request for a minimum order quantity of 600/800 kg. Orders will be fulfilled in 20/30 days.
66 | ICR SPRINT COMPOSITES
67.
68. COMPANY WITH
QUALITY SYSTEM
CERTIFIED BY DNV GL
= ISO 9001 =
1/2020
I.C.R. S.p.A.
ITALIA - Reggio Emilia
Tel. + 39/0522.517803 – Fax + 39/0522.514384
E-mail: info@icrsprint.it – www.icrsprint.com
ICR Ibérica. S.A.
SPAIN - Tel. +34/901 101 408
E-mail: info@icriberica.com
www.icriberica.com
ICR SPRINT INC
USA - Fall River - MA - T: 800 980 4071
E-mail: hello@icrsprintus.com
www.icrsprint.com
ICR SPRINT COATING UK LTD
UK - London - T: 01278802011
E-mail: enquiries@icrsprint.co.uk
www.icrsprint.com