ICR SPRINT SC9 CREAMY YELLOW PUTTY - Stucco per lamiere zincate ed alluminio ...
ICR SPRINT A14 NITRO PRIMER GREY - Monocomponente nitrosintetico / One-component nitro-synthetic primer
1. Isolante nitrosintetico ad uso generale ad alto potere
riempitivo e veloce indurimento.
Può essere sovrapposto con vernici nitrocellulosiche,
sintetiche ed acriliche.
Ha una eccellente adesività, forte potere coprente e con
più passate si possono ottenere anche grossi spessori.
Non è assorbente e lascia la superficie
perfettamente liscia.
Nitro-synthetic basecoat of general use with
high filling properties and fast drying.
Can be topcoated with nitrocellulose, synthetic and
acrylic finish.
Has excellent adhesion and strong covering power.
Can be applied in thick coats.
Is non-absorbing and leaves a very smooth surface.
The EU VOC limit for this ready-to-use product is 540 g/l.
A14 NITRO PRIMER
GREY.
1K NITRO-SYNTHETIC
GREY PRIMER.
A14 NITRO PRIMER
GREY.
MONOCOMPONENTE
NITROSINTETICO.
www.icrsprint.com
2. A) DESCRIZIONE E CAMPO D’IMPIEGO:
Isolante nitrosintetico di uso generale ad alto potere riempitivo e veloce
indurimento. Può essere sovrap-posto con vernici nitrocellulosiche, sinteti-
che ed acriliche. Ha una eccellente adesività, forte potere coprente e con
più passate si possono ottenere anche grossi spessori. Non è assorbente
e lascia la superficie perfettamente liscia.
B) NOTE TECNICHE:
Composizione: Resine sintetiche, nitrocellulosa, cariche minerali e
solventi
Peso specifico: 1,2 ± 0,1
Colori disponibili: Grigio
Dati di sicurezza: Fare riferimento alla scheda di sicurezza
C) PREPARAZIONE DEL SUPPORTO:
• Lamiera nuda, laminati in poliesteri, legno,
stucchi poliestere, ecc.
• Vecchie finiture comprese quelle in acrilico termoplastico e
doppio strato.
• Carteggiare con carta abrasiva P180-P220.
• Pulire bene la superficie da trattare con Antisil V09 e
assicurarsi che sia asciutta e priva di silicone, cere, grassi
e sostanze estranee in genere.
D) AVVERTENZE:
> Rispettare i tempi di appassimento tra una mano e l’altra a secondo
della diluizione e della temperatura.
> Rispettare la corretta diluizione.
> Non utilizzare il prodotto a temperature inferiori a 5°C.
> Conservare in luogo fresco ed asciutto.
E) LAVORAZIONE:
50-100% con diluente nitro
18-25” DIN 4 mm a 20°C.
1,5-1,8 mm 2-4 bar
2-3 = 25-50 micron
20-30’ a 20°C
2-3’ a 1 mt
P600-P1000
F) PULIZIA DEGLI ATTREZZI:
> Con diluente nitro
G) PROSECUZIONE DELLA LAVORAZIONE:
Smalti di finitura bicomponenti
Smalti doppio strato a solvente
Smalti doppio strato ad acqua
Le informazioni tecniche ed i suggerimenti sono conformi a quanto risulta dalle nostre esperienze.
Noi assicuriamo la perfetta qualità del prodotto. Tuttavia, non essendo le condizioni di
utilizzo sotto il nostro controllo, non assumiamo nessuna responsabilità sui risultati ottenuti.
IT SCHEDA TECNICA A14
NITRO PRIMER GREY
Monocomponente nitrosintetico
NITRO PRIMER GREY
One-component nitro-synthetic grey primer
A) DESCRIPTION AND FIELDS OF APPLICATION:
Nitro-synthetic basecoat of general use with high filling properties and
fast drying. Can be topcoated with nitrocellulose, synthetic and acrylic
finish. Has excellent adhesion and strong covering power. Can be
applied in thick coats. Is non-absorbing and leaves a very smooth
surface.
B) TECHNICAL DATA:
Composition: Synthetic resins, nitrocellulose, mineral charges
and solvents
Specific weight: 1.2 ± 0.1
Available colours: Grey
Safety data: See safety data sheet
C) SURFACE PREPARATION:
• Bare metal, polyester laminates, wood,
polyester fillers, etc.
• Old finishes, including the double-coat and the thermoplastic
acrylic paints.
• Sand with P180-P220.
• Clean the surface to be treated with V09 Antisil. Make sure it
is dry and free from silicone, wax, grease and any
extraneous material.
D) CAUTIONS:
> Allow flash-off time between coats, depending on reduction and
temperature.
> Respect correct reduction
> Do not utilize the product at temperatures below 5°C.
> Store in a cool and dry place.
E) PROCESSING:
50-100% with nitro thinner
18-25” DIN 4 mm at 20°C
1,5-1,8 mm 2-4 bar
2-3 = 25-50 microns
20-30’ at 20°C
2-3’ at 1 m
P600-P1000
F) TOOLS CLEANING:
> With nitro thinner.
G) RECOATING:
2K enamel top coats
double coat solvent-soluble enamels
double coat water-soluble enamels
Technical indications and advices are based on our own experiences.
We assure the perfect quality of products. However, being the utilization out of our
control, we assume no responsibility on the results obtained.
EN TECHNICAL SHEET A14
I.C.R. S.p.A. ITALIA - Reggio Emilia Tel. + 39/0522.517803 – Fax + 39/0522.514384 E-mail: info@icrsprint.it – www.icrsprint.com |
ICR SPRINT COATING UK LTD UK - London - T: 01278802011 E-mail: enquiries@icrsprint.co.uk www.icrsprint.com |
ICR SPRINT INC USA - Fall River - MA - T: 800 980 4071 E-mail: icrsprintusa@gmail.com www.icrsprint.com |
ICR Ibérica, S.A. SPAIN - Tel. +34/901 101 408 E-mail: info@icriberica.com www.icriberica.com