Manual de tarjeta madre- U8668

U8668--D
U8668 D

FCC Information and Copyright

This equipment has been tested and found to c omply with the limits of a
C lass B digital device, pursuant to Part 15 of the FCC Rules . T hese limits
are designed to provide reasonable protection agains t harmful
interference in a residential installation. This equipment generates , uses
and can radiate radio frequency energy and, if not ins talled and used in
accordance with the instructions, may c ause harmful interference to radio
communications . There is no guarantee that interference will not occur in
a partic ular installation.

The vendor makes no representations or warranties with respec t to the
contents here of and specially disclaims any implied warranties of
merchantability or fitness for any purpose. F urther the vendor reserves
the right to revise this publication and to make changes to the c ontents
here of without obligation to notif any party beforehand.
y
Duplication of this publication, in part or in whole, is not allowed without
firs t obtaining the vendor’s approval in writing.

The c ontent of this user’s manual is subject to be changed without notice
and we w not be responsible for any mistakes found in this us er’s
ill
manual. A ll the brand and product names are trademarks of their
respective c ompanies .

i

U8668--D
U8668 D

ENGLIS H................................................................................................... 3
U8668-D Features.................................................................................3
Package contents...................................................................................4
Layout of U8668-D (only for version 1.x and 6.x) .........................5
Layout of U8668-D (only for version 3.3).......................................6
Layout of U8668-D (only for version 4.0).......................................7
Layout of U8668-D (only for version 5.x).......................................8
Layout of U8668-D (only for version 5.A)......................................9
Layout of U8668-D (only for version 5.B & above).....................10
Layout of U8668-D (only for version 7.0~7.3).............................. 11
Layout of U8668-D (only for version 7.5~7.7)..............................12
Layout of U8668-D (only for version 7.8 & above)......................13
CPU Installation .................................................................................14
DDR DIMM Mo dules: DDR1-2 ........................................................14
Jumpers, Headers, Connectors & Slots............................................15
TROUB LE S HOOTING..................................................................... 21
ES PAÑOL ................................................................................................ 22
Características del U8668-D..............................................................22
Contenido del Paquete .......................................................................23
SOLUCIÓN DE PROBLEMAS ......................................................... 24
FRANÇAIS .............................................................................................. 25
Caractéristiques de U8668-D.............................................................25
Contenu de l'Emballage.....................................................................26
DÉPANNAGE ...................................................................................... 27
Chapter 3: WarpS peeder™ ...................................................................28

ii

Motthe rboa r d D e sc riipttiion
Mo he rboa r d D e sc r p on

English
U8668-D Features
CPU
Provides Socket-478.
® ®
Support the Intel Pentium 4 Northwood CPU up to 3.06G Hz.
® ®
Supports the Intel Pentium 4 478 Prescott CPU (f or v ersion 5.A/5.B and
v ersion 7.5 & abov e).
- 533FSB with 1024KB L2 Cache
- Celeron D (533 FSB with 256KB L2 Cache)
Running at 400/533MHz Front Side Bus.
Supports Hy per-Threading Technology.
Version 7.8 and above do not support Willamette CPU.
Standard Intel CPU f an is suggested.
Chipset
North Bridge: P4M266A
South Bridge: VT8235
Main Memory
Supports up to 2 DDR devices.
Supports 200 /266MHz DDR devices.
The largest memory capacity is 2GB.

Super I/O
Chipset: ITE IT8705.
Slots
Three 32-bit P bus master slots (for version 3.x, 4.x, 5.x, 5.A, 5.B and 7.x).
CI
Two 32-bit PCI bus ma ster slots (only f or v ersion 1.x and 6.x).
One CNR slot (f or v ersion 3.x, 4 5.x, 5 5.B and 7.x only ).
.x, .A,
One AMR slo (for version 1.x and 6.x).
t
One AGP slo t.
On Board IDE
Supports four IDE disk drives.
Supports PIO Mode 4, Master Mode and Ultra DMA 33/66/100/133 Bus
Master Mode.

LAN (only support for version 3.3)
Chip: RTL8201BL.
10/ 100Mbps.
Half/Full duplex operation.
LAN
VIA VT6103/6103L (Only Version 7.8 and abov e support V VT6103L
IA
chipset.)
Dual Speed: 10/100Mbps, Full/Half Duplex.
Auto Negotiation: 10/100 Mbps, Full/Half Duplex.

3


On Board AC’97 Sound Codec
Chip: VIA1612A (for version 3.x, 6.x, and 7.0-7.6)
Compliant with AC’97 specification.
Supports 2 channel speakers.

On Board AC’97 Sound Codec (optional)
Chip: CMI9739A (for version 1.x, 4.x, 5.x, 5.A, 5.B, 7.7, 7.8 & abov e)
Compliant with AC’97 specification.
Supports 6 channel speakers.

On Board Peripherals
Supports 360K, 720K, 1.2MB, 1 .44MB and 2.88MB f loppy disk driv ers.
Supports 1 serial port.
Supports 1 VGA port.
Supports 1 multi-mode parallel port. (SPP/EPP/ECP mode)
Supports PS/2 mouse and PS/2 key board.
Supports 6 USB2.0 ports. (Either rear x 4 + f ront x 2 or rear x 2 + front x 4)

BIOS
AWARD legal Bios.
Supports APM1.2.
Supports ACPI.
Supports USB Function.

Operating System
Offers the highest performance for MS-DOS, Windows 2000, Windows Me,
Windows XP, SCO UNIX etc.

Dimensions
Micro ATX Form Factor: 19.5cm X 22.8cm (W X L) (only f or v ersion 1.x and
6.x)
Micro ATX Form Factor: 19.5cm x 24.4cm (W x L) (only f orv ersion 3 4.x,
.x,
5.x, 5.A, 5.B and 7.x)

Package contents
FDD Cable
HDD Cable
User’s Manual
Fully Setup Driv er CD
USB Cable (optional)
Rear I/O Panel (optional)

4


Layout of U8668-D (only for version 1.x and 6.x)
JK BMS1
1
K/ B
&
Mouse JATX PWR 1
C PU JC FA N 1

S ocket 478

JCO M1
COM1

JA TXPW R2
Pa rall el Port

DDR 1
DDR 2
VG A1

JPR NT1
ID E1 ID E2

JVGA 1
JU SBLA N1 Super
USB I/O
& P4M 266A
L AN

JAU DIO

10 9
BIOS
JA U DIO 1
2 1 A G P1
JC MO S1
LAN JU SB2
1
2 10
C ode c PCI1 1 9 BAT1

2 JGA ME1 16
JSPDIFO 1 1
PCI2

1 15

A MR 1 FD D1 JSFAN 1
JCD IN 1 1 JCI1
1 JPA NEL1 1
1 2 24
JW O L1 1 23

Back Panel Connector

JKBMS1 JPRNT1 JUSBLAN2
PS/2 LAN
Mouse Parallel
Line In
Speaker Out

Mic In

PS/2 USB COM1 V GA USB
Keyboard
JUSB1 JCOM1 JVGA1 JAUDIO

5


Layout of U8668-D (only for version 3.3)
JKBMS1 JKBS 1
1 1
K/B
&
Mo use JATX PWR 1
CP U JCFA N1

Soc ke t 478

JCO M1
COM1

JP RNT1 JATX PW R2
P arall e Por t

DD R1
DDR2
l
VGA1

1
JUS BV2 I DE1 I DE2

JVGA1
JUSBLAN1 Super
U SB I/O
& P4M 266A
LA N

JAU DIO

10 9
BIOS
JAU DI O1
2 1 AGP 1
JC MOS 1
LAN JUS B2
1
2 10
C od ec
P CI 1 1 9 BA T1

2 JGAME1 16 JS P DI FO 1 1
P CI2

1 15

P CI3 1 JUS BV3
JCDI N1
1
JWO L1 1
JS FA N1
CN R1 F DD1 1 JCI 1
JP AN EL1 1
2 24
1 23

JKBMS1 JUSBLAN2
JPRNT1
PS/ 2 LAN
Mouse Parallel
Line In

Speaker Out

Mic In

PS /2 USB COM1 VGA USB
Keyboard

6


Layout of U8668-D (only for version 4.0)
JKBMS1
1
K/B
&
Mo use JATX PWR 1
CP U JCFA N1

So c ke t 4 7 8

JCO M1
COM1

JP RNT1 JATX PW R2
P arall e Por t

DD R1
DDR2
l
VGA1

I DE1 I DE2

JVGA1
JUSBLAN1 Super
U SB
&
I/O P4M266A
LA N

JAU DIO

10 9
BIOS
JAU DI O1
2 1 AGP 1
JC MOS 1
LAN JUS B2
1
2 10
C od ec
P CI 1 1 9 BAT1

P CI2

1 15

JCDI N1 P CI3
1
JWO L1 1
JS FA N1
CN R1 F DD1 1 JCI 1
JP AN EL1 1
2 24
1 23

PS/2 LAN
Mouse Parallel
Line In

Speaker Out

Mic In

PS/2 USB COM1 VGA USB
Keyboard

7


Layout of U8668-D (only for version 5.x)
JKBMS1 JKBS 1
1 1
K eybo ard
&
Mo use JATX PWR 1
CP U JCFA N1

So c ke t 4 7 8

JCO M1
COM1

JP RNT1 JATX PW R2
P arall e Por t

DD R1
DDR2
l
VGA1

1 I DE1 I DE2
JU SBV 2
JVGA1
JUSBLAN1 Super
U SB
&
I/O P4M266A
LA N

JAU DIO

10 9
BIOS
JAU DI O1
2 1 AGP 1
JC MOS 1
LAN JUS B2
1
2 10
C od ec
P CI 1 1 9 BAT1

P CI2

1 15

P CI3 1 JUS BV3
JCDI N1
1
JWO L1 1
JS FA N1
CN R1 F DD1 1 JCI 1
JP AN EL1 1
2 24
1 23

J KBMS1 JPRNT1 JUSBLAN2
PS/2 LAN
Mouse P arallel
Li ne In
(Optional)
Speaker Out

Mic In

Keyboard
JUSB1 J COM1 JVGA1 JAUDIO

8


Layout of U8668-D (only for version 5.A)
JK B M S1 JK B S 1
K eyboard 1 1
&
M ouse JA T X PW R 1
CPU JC F A N 1

Socket 478

JC O M 1
COM 1

JP R N T 1 J TXPW R 2
A
t
ParalelP or

D DR1
DD R2
l
VGA1

ID E 1 I E 2
D

J GA1
V
JU SB L A N 1
1
USB JU SB V 2
& P4M 266A
LAN

J U DI 2
A O

JA U D IO 1
1
15 A GP1
16
JC M O S1
2
LAN JU S B 2
1
2 10
Codec P C I1 1 9 BAT1
JW O L 1 JC D IN 1
2 10
1 1
1 JS PD I O 1
F 1
PCI
2
1
JU SB 3
9 VT8235
JSATA 1

S uper 1
I/O PCI
3 1 JU S B V 3
JSATA2

JSF A N 1
CN R1 FDD 1 1 JC I1
B IO S J A NEL1 1
P
2 24
1 23


PS/2 LAN
Mouse Parallel
Line In
(Optional)
Speaker Out

Mic In

Keyboard

9


Layout of U8668-D (only for version 5.B & above)
JK B M S 1 JK B S1
1 1
Keyboard
&
M ouse JA T X P W R 1
CPU JC FA N 1

Socket478

JC O M 1
CO M 1

JPR N T 1 JA T X PW R 2
ralel t
P a l Por

DDR1
D DR2
VGA1

ID E 1 ID E 2

JV G A 1

1
J SB V 2
U
J S BL A N 1
U P4M 266A

JA U D I 2
O 10 9

2 1
J U D IO 1
A
AGP1
JC M O S 1
LA N 1
2 J SB 2 1 0
U
VT8235
C od e c PC I1 1 9 BAT1
J O L 1 JC D I 1
W N
2 10
1 1 1
JSP D IFO 1 1 PC I2 1 9
JU S B 3 JSATA1
( Op ti on al )
S uper 1
I/O PC I3 JSATA 2
JU S B V 3 ( Op ti on al)
1
JSF A N 1
CN R1 FD D 1
B IO S 1 JC I1
JPA N E L 1 1
2 24
1 23

PS/2 LAN
Mouse Parallel
Line In
(Optional)
Speaker Out

Mic In

Keyboard

10


Layout of U8668-D (only for version 7.0~7.3)
J KBM S1
K/B 1
&
Mouse JCF AN1 JATXPWR1
CPU

US B So ck et 4 78
&
LAN

JCOM1
COM1

JATXPWR2
Parallel Por t

DDR1
DDR2
VGA1

JP RNT1
ID E1 ID E2

JVGA1
Sup er
I/O
MI C-IN LIN E-IN SP-OU T

P4M2 66 A
GAME Por t

JA UD _GA ME

BI OS
10 9
AGP 1
JA UDIO1 JCMOS1
2 1 LAN JUS B4
1
2 10
Co dec PCI1 1 9 B AT1

2 JGAME1 16 JSP DIF O1 1 2 JUS B2 10
PCI2 1 9

1 15

JCDI N1 PCI3
1
JWOL1 1
JSF AN1
CNR1 FDD1 1 JCI1
1
JPA NEL1 2
1
24
23


JKBMS1 JUSBLAN1
PS/2 LAN(Optional) JPRNT1 JGAME1
Mouse Parallel Game Port

P S/2 USB COM1 VGA1 Speaker Line In Mic
Keyboard Out In
JCOM1 JVGA1

11


Layout of U8668-D (only for version 7.5~7.7)
JKBMS1
1
Key board
&
Mouse JA TX PWR 1
CPU JC FAN1

Soc ket 478
JUSBLAN1

JCO M1
COM1

JPRNT1 JATXPWR2
P ar allel Po rt

DDR1
DDR2
VGA1

IDE1 ID E2

JVGA1
MI C-I N LINE- IN SP-OUT

P4M266A
GAME Port

JAU D_GA ME

10 9

JAUD IO 1

21 AGP1
JCMO S1
LAN JUSB4
1
2 10
C od ec PCI1 1 9 BAT 1
VT8235
JWO L1
JCDIN1
1 2 10
1 1
JSPDIFO1 1 PCI2 1 9
JUSB2 JS ATA 1

Supe r 1
2 10
I/O PCI3 1 9
JU SB3 JS A 2
TA

JSFAN 1
CNR1 FDD 1 1
BI OS JPAN EL1
JCI1
1
2 24
1 23


JKBMS1 JUSBLAN1
Mouse Paral lel Game Port

PS/2 USB COM1 VGA1 Speaker Line In Mic
Keyboard Out In
JCOM1 JVGA1

12


Layout of U8668-D (only for version 7.8 & above)
JKBMS1
1
Keyb oard
&
Mouse JCF AN1 JA TXP WR1
CPU

So c ke t 47 8
JUSBLAN1

JCOM1
COM1

JP RNT1 JATXP WR2
Parallel P ort

DD R1
DDR2
VGA1

ID E1 I DE2

JVGA1
M IC- IN LINE-IN SP-OUT

P4M 266A
GAME P ort

JA UD_G AME

10 9

JAU DIO 1

21 AGP 1
JCMOS1
LAN 1
2 JUSB4 10
Co de c PC 1
I 1 9 BAT1
JWOL1 JCDI N1
VT8235
1 2 10 1
1 JS PDI F O1 1 1 9
PCI 2 JU SB2 JSATA1

Super 1
2 10
I /O PCI 3 1 9
JUS B3 JS ATA 2

JS FAN 1
CNR1 F DD1 1 JCI1
BI OS JP ANEL1 1
2 24
1 23


JKBMS1 JUSBLAN1
Mouse Paral lel Game Port

PS/2 USB COM1 VGA1 Speaker Line In Mic
Keyboard Out In
JCOM1 JVGA1

13


CPU Installation
CPU Fan

CPU

1. Pull the lever sideway s away from the socket then raise the lever up to a
90-degree angle.

2. Locate Pin A in the socke and loo for the white do or cut edge in the CPU.
t k t
Match Pin A with the white dot/cut edge then insert the CPU.

3. Press the lever down. Then Put the f an on the CPU and buckle it and put the
f an’s power port into the JCFAN1, then to complete the installation.

CPU/ S ystem Fan Headers: JCFAN1/ (JS FAN1 => optional)

1 Ground 1 Ground
12 V 12V
Sense Sense

J CFAN1 JSFAN1

DDR DIMM Modules: DDR1-2
DRAM Access Time: 2.5V Unbuffered/ Registered DDR 200 MHz (PC1600)/
DDR 266 MHz (PC2100) Ty pe required.
DRAM Ty pe: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module.(184 pin)

DIMM Socket DDR Module Total Memory Size
Location (MB)
DDR 1 64MB/128MB/256MB/512MB/1GB *1 Max is
DDR 2 64MB/128MB/256MB/512MB/1GB *1 2GB
The list shown abov e f or DRAM configuration is only f or reference.

14


How to install DDR DIMM Module
1. The DDR DIMM socket ha a “ Plastic Saf e
s ty
Tab”, and the DDR DIMM me mory module has an
Asy mmetrical notch”, so the DDR DIMM memory
module can only f it into the slot in one direction.

2. Push the tabs out. Insert the DDR DIMM
memory modules into the so cket at a 90-degree
angle, and then push down vertically so that it will
f it into the place.

3. The Mounting Holes and plastic tabs should fit
over the edge and hold the DDR DIMM memory
modules in place.

Jumpers, Headers, Connectors & Slots
Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/ 66 100/ 133 functionality. It has two
/
HDD connectors IDE1 (primary) and IDE2 (secondary).
The IDE connectors can connect a master and a slave driv e, so you can connect
up to f our hard disk driv es. The f irst hard drive should alway s be connected to
IDE1.

Floppy Disk Connector: FDD1
The motherboard provides a standard f loppy disk connector tha suppor 360K,
t ts
720K, 1.2M, 1.44M and 2.88M flopp disk types. This connector supports the
y
prov ided f loppy drive ribbon cables.

Audio Modem Riser Slot: AMR1 (only for version 1.x and 6.x)
(Only support slav e card)
The AMR specif ication is an open Industry Standard Architecture and that defines
a hardware scalable riser card interface, which supports audio and modem only.

Peripheral Component Interconnect Slots: PCI1-3 (only for
version 3.x, 4.x, 5x, 5.A, 5.B, 7.x)
This motherboard is equipped with 3 standard PCI slots. PCI stands f or Peripheral
Component Interconnect, and it is a bus standard for e xpansion cards. This PCI
slot is designated as 32 bits.

Peripheral Component Interconnect Slots: PCI1-2 (only for
version 1.x and 6.x)
This motherboard is equipped with 2 standard PCI slots. PCI stands f or Peripheral
Component Interconnect, and it is a bus standard for e xpansion cards. This PCI
slot is designated as 32 bits.

15


Accelerated Graphics Port S lot: AGP1
Y our monitor will attach directly to that v ideo card. This motherboard supports
video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port
(AGP). An AGP card will take adv antage of AGP technology f or improved v ideo
efficiency and performance, especially with 3D graphics.

Communication Network Riser S lot: CNR1 (optional)
The CNR specification is an open Industry Standard Architecture and it defines a
,
hardware scalable riser card interf ace, which supports audio and modem only.

Front USB Header: JUSB2/ (JUS B3=>only for version 5.A & 5.B,
7.2; JUS B4=>only for version 7.x)

2 Pin Assignment Pin Assignment
1 +5V 2 +5V
1 3 Data (-) 4 Data (-)
5 Data (+) 6 Data (+)
JUSB2/4 7 Ground 8 Ground
9 Key 10 NA

Power Connectors: JATXPWR1/ J ATXPWR2

JATXPWR2
( ATX 12V Power Connector)

JA TX PWR1
( AT X Ma in P ow er Connec tor )

JATXPWR1
PIN Assignment PIN Assignment
1 +3 .3V 11 +3 .3V
2 +3 .3V 12 -12V
3 G round 13 G round
4 +5V 14 PS_O N
6 +5V 16 G round
8 PW_OK 18 -5V
9 +5V _S tandby 19 +5V
10 +12V 20 +5V

16


JATXPWR2
PIN A ssignment PIN Assignment
1 12V 3 G round
2 12V 4 G round

Front Panel Connector: JPANEL1
PWR_LED
SLP (+ ) ( +) (- )
ON/OFF IR
2 24
1 23
(+ ) ( -)
SPK RST IR
HLED
SPK ==> Speaker Conn.
HLED ==> Ha rd Driver LED
RST ==> Reset Button
IR ==> Infrared Conn.
SLP ==> Sleep Button
PWR_LE D ==> Power LED
ON/ OFF ==> Power-on Button

Clear CMOS Jumper: JCMOS
JCMOS Assignment
Pin 1-2 on Normal
Operation
1 (default)

Pin 2-3 on
Clear CMOS
Data
1

※ Clear CMOS Procedures:
1 . R emove AC power line.
2 . S et JC MO S1 (2-3 ) closed.
3 . Wait for five seconds .
4 . S et JC MO S1 (1-2 ) closed.
5 . Power on AC .
6 . R eset your desired pass word or c lear the CMO S data.

Audio S ubsystem: JAUDIO1/ JCDIN1
10 9
2
1 1
2 1
JA UD IO1 JC DIN 1
(Fro n t Au dio Head er) ( CD-RO M A u dio- In H ead er)

17


22 10
JF_ AU DIO 1
1 9

Pin Ass ignment Pin Assign ment
1 Mic In 2 Ground
3 Mic Power 4 Audio Po wer
5 RT Line Out 6 RT Line Out
7 Reserved 8 Key
9 LFT Line Out 10 LFT Line Out

Fro nt Pan el Au dio C onn ecto r/ Ju mper B lock

Jump er Se tting C on fig ur ation

1 2
3 4 Pin 5 and 6
5 6 Audio lin e o ut sig nals are rou ted to
7 Pin 9 and 1 0
th e b ack pan el au dio lin e o ut conn ecto r.
9 10

1 2
3 4
5 6 No jum per s Aud io line ou t an d m ic in sign als ar e
7 installed av ailabl e fo r fro nt pan el au dio co nn ector s.
9 10

Audio S ubsystem: JCDIN1/ JAUD IO1 (only support for version
5.1 & 5.A)

15 1 1
16 2
JAUDIO1 J CDIN1
(Front Audi o Header) (C D-ROM Audio-In Header)

15 1
2 JAUDIO1
16 2

Pin Assignment Pin Assignment
1 Mi c In 2 Ground
3 Mic Power 4 Audio Power
5 Right Line Out 6 Right Line Out
7 Reserved 8 NC
9 Left Line Out 10 Left Line Out
11 Surrender Right 12 Surrender Left
13 Center 14 Subwoof
15 Ground 16 KEY

18


Game Header: JGAME1 (o ptional)
2 16 JGAME1
1 15
Pin Assignment Pin Assignment
1 +5V 2 +5V
3 GP6 4 GP4
5 GP2 6 GP0
7 MIDI-OUTR 8 Ground
9 GP3 10 Ground
11 GP7 12 GP1
13 MIDI-INR 14 GP5
15 NC 16 +5V

Digital Audio Connector: JS PDIF_OUT1 (optional)
S PDIF_Out
GND 5V

1

JSPDIF_ OUT

Wake On LAN Header: JWO L1 (optional)
Gr ound
5V Wake up

1

JWOL1

Case Open Connector: JCI1 (optional)

JCI1 Assignment
1 Normal
Operation
No jumper (default)
installed
1
Case Open
Pin 1-2 on

19


Power S ource Selection for KB/MS and US B0/1: JKBS 1 (only
for version 3.3 and 5.x, 5.A, 5.B)
JKBS1 Assignment
1
5V
Pin 1-2 on

1 5V_SB
Pin 2-3 on

Power S ource Selection for USB: JUSBV2/ JUS BV3 (only for
version 3.3 and 5.x, 5.A, 5.B)
JUSBV2/3 Assignment

1 5V
Pin 1-2 on

1 5V Standby
Pin 2-3 on

20


Trouble Shooting
PROBABLE SOLUTION
No power to the system at all Power light * Make sure power cable is securely
don’t illuminate, f an inside power supply plugged in
does not turn on. Indicator light on * Replace cable
key board does not turn on * Contact technical support
Syste inoperativ e. Keyboard lights are * Using even pressure on both ends of
m
on, power indicator lights are lit, hard the DIMM, press down firmly until the
driv e is spinning. module snaps into place.

Syste does not boot from hard disk
m * Check cable running from disk to disk
driv e, can be booted f ro optical driv e.
m controller board Make sure both ends
.
are securely plugged in; check the
driv e type in the standard CMOS
setup.
* Backing up the hard drive is extremely
important. All hard disks are capable of
breaking down at any time.
Syste only boots f rom optical driv e.
m * Back up data and applications files.
Hard disk can be read and applications Ref ormat the hard driv e. Re-install
can be used but booting from hard disk is applications and data using backup
impossible. disks.
Screen message says “Invalid * Review system’ equipment . Make
s
Conf iguration” or “CMOS Failure.” sure correct information is in setup.

Cannot boot system after installing * Set ma ster/slave jumpers correctly.
second hard driv e. * Run SETUP program and select correct
driv e types. Call drive manuf acturers
f or compatibility with other drives.

21


Español
Características del U8668-D
CPU
Proporciona Socket-478.
Soporta procesador Intel Pentiu 4 de hasta 3.06GHz.
m
Soporta Intel Pentium 4 478 Prescott CPU. (solamente para v ersión 5.A/5.B
en adelante; 7.5 en adelante)
Corre a 400/ 533MHz Front Side Bus.
Soporta Tecnología Hyper-Threading.
La versión 7.8 no admite el procesador Willamette.
Se recomienda el ventilador de procesador Intel estándar.

Chipset

Memoria Principal
Soporta hasta 2 dispositivos DDR.
Soporta dispositivos DDR de 200/ 266MHz.
Capacidad máxima de memoria 2GB.

Super I/O

Ranuras
Dos ranuras de 32-bit PCI bus master. (solamente para versión 1.x y 6.x)
Tres ranuras de 32-bit PCI bus master. (solamente para versión 3.x, 4.x, 5.x,
5.A, 5.B y 7.x)
Una ranura CNR. (sola mente para versión 3.x, 4.x, 5.x, 5.A 5.B y 7
, .x)
Una ranura AMR. (solamente para v ersión 1.x y 6.x)
Una ranura AGP.

IDE Onboard
Soporta cuarto discos IDE.
Soporta Modos PIO 4, Modo Master y Modo Ultra DMA 33/66/100/133 Bus
Master.

LAN (solamente soporta para versión de placa madre 3.3)
RealTek RTL8201BL.
10/100Mbps.
Full/Half Duplex.

LAN
VIA VT6103/6103L (Sólo la versión 7.8 y posteriores admiten el conjunto de
chips VT6103L).
Dual Speed: 10/100Mbps.

22

Full/Half Duplex.
Auto Negociación: 10/100 Mbps, Full/Half Duplex.

AC’97 Sound Codec Onboard
Chipset: VIA1612A (solamente para v ersión 3.x, 6 y 7.0-7.6)
.x,
Constituy e con la especificación del AC’97.
Soporta 2 canales.

AC’97 Sound Codec Onboard (opcional)
Chipset: CMI9739A (solamente para v er sión 1.x, 4.x, 5.x, 5 , 5.B, 7.7, 7.8
.A
y posteriores )
Constituy e con la especificación del AC’97.
Soporta 6 canales.

Periféricos Onboard
Soporta disquette de 360K, 720K, 1.2MB, 1.44MB y 2.88MB.
Soporta 1 puerto serie.
Soporta 1 puerto VGA .
Soporta 1 puerto paralelo multi-mode. (modo SPP /EPP/ECP)
Soporta ratón PS/2 y teclado PS/2.
Soporta 6 puertos USB2.0 (2 x traseros + 4 x f rontales/ 4 x traseros + 2 x
frontales.

BIOS
AWARD legal Bios.
Soporta APM1.2.
Soporta ACPI.
Soporta f unción USB.

Sistemas Operativos
Ofrece el más alto funcionamiento para MS-DOS, Windows 2000, Windows
Me, Windows XP, SCO UNIX etc.

Dimensiones
Factor de Forma Micro ATX: 19.5cm X 22.8cm (W X L) (solamente para
v ersión 1.x y 6.x)
Factor de Forma Micro ATX: 19.5cm x 24.4cm (W X L) (solamente para
v ersión 3.x, 4 5.x, 5.A, 5.B y 7.x)
.x,

Contenido del Paquete
Cable HDD
Cable FDD
Manual del Usuario
Cable USB (Opcional)
Panel Trasero I/O (Opcional)
Configuración completa del Driver CD

23


Solución de Problemas
CAUS A PROBABLE SOLUCIÓN
No ha corrien en el sistema. La luz de *
y te Asegúrese que el cable de transmisión
corriente no ilumina, ventilador dentro de esté seguramente enchu ado.
f
la f uente de alimentación apagada. * Reemplace el cable.
Indicador de luz del teclado apagado.
* Contacte ayuda técnica.
Sistema inoperativo. Luz del teclado * Presione los dos extremo del DIMM,
s
encendido, luz de indicador de corriente presione para abajo f irmemente hasta
iluminado, disco rígido está girando. que el módulo encaje en el lugar.
Sistema no arranca desde el disco rígido, * Controle el cable de ejecución desde el
puede ser arrancado desde el unidad disco hasta el disco del controlador.
óptica. Asegúrese de que ambos lados estén
enchu ados con seguridad; controle el
f
tipo de disco en la configuración
estándar CMOS.
* Copiando el disco rígido es
extremadamente importante. Todos
los discos rígidos son capaces de
dañarse en cualquier momento.
Sistema solamente arranca desde el * Copie datos y documentos de
unidad óptica. Disco rígido puede leer y aplicación. Vuelva a f ormatear el
aplicaciones pueden ser usados pero el disco rígido. Vuelv a a instalar las
arranque desde el disco rígido es aplicaciones y datos usando el disco
imposible. de copiado.
Mensaje de pantalla ”Inv alid * Revise el equipo del sistema.
Conf iguration” o “CMOS Failure.” Asegúrese de que la información
conf igurada sea correcta.
No puede arrancar después de instalar el * Fije correctamente el puente
segundo disco rígido. master/esclav o.
* Ejecute el programa SETUP y
seleccione el tipo de disco correcto.
Llame a una manuf acturación del disco
para compatibilidad con otros discos.

24


Français
Caractéristiques de U8668-D
CPU
Offre les Socket-478.
Supporte le processeur Intel Pentium 4 jusqu’à 3.06GHz.
Supporte Intel Pentium 4 478 Prescott CPU. (pour v ersion 5.A/5B, e 7.5)
t
Fonctionnant en Bus Frontal de 400/ 533MHz.
Supporte Hy per-Threading.
Les versions 7 et plus ne sont pas compatibles a
.8 vec les processeurs
Willamette.
Les ventilateurs pour CPU Intel standard sont reco mmandé s.

Chipset

Mémoire Principale
Supporte jusqu’à 2 matériels DDR.
Supporte des matériels DDR en 200/266MHz.
La plus grande capacité mémoire est 2Go.

Super E/S

Slots
Deux slots de maîtrise de bus PCI 32 bits. (seulment pour version 1.x et 6.x)
Trois slots de maîtrise de bus PCI 32 bits. (seulment pour v ersion 3.x, 4.x, 5.x,
5.A, 5 et 7.x)
.B,
Un slo CNR. (seulment pour version 3.x, 4.x, 5.x, 5.A, 5.B e 7.x)
t t
Un slo AMR. (seulment pour v ersion 1.x et 6.x)
t
Un slo AGP
t

IDE Interne
Supporte quatre disques durs IDE.
Supporte PIO Mode 4, le Mode Maître et le Mode de Maîtrise de Bu Ultra
s
DMA 33/66/100/133.

LAN (seulment pour version 3.3)
RealTek RTL8201BL.
10/100Mbps.
Full/Half Duplex.

LAN
VT6103/6103L (Seules les versions 7.8 e plus sont compatibles avec le
t
chipset VT6103L).
Double Vitesse: 10/100Mbps.

25

Full/Half Duplex.
Négociation automatique : 10/100 Mbps, Full/Half Duplex.

Codec Son AC’97 Interne
Chipset: VIA1612A (seulment pour v ersion 3.x, 6.x et 7.0-7.6)
Conforme aux spécif ications du codec AC’97.
Supporte 2 canaux.

Codec Son AC’97 Interne (optionnel)
Chipset: CMI9739A (seulment pour v ersion 1.x, 4 5.x, 5.A, 5.B ,7.7, 7.8 et
.x,
plus)
Conforme aux spécif ications du codec AC’97.
Supporte 6 canaux.

Périphériques Internes
Supporte les lecteurs de disquettes 360K, 720K, 1.2Mo, 1.44Mo et 2 .88Mo.
Supporte 1 port série.
Supporte 1 port VGA.
Supporte 1 port parallèle multi-mode. (mode SPP/EPP/ECP)
Supporte souris PS/2 et clav ier PS/2.
Supporte 6 ports USB2.0 (2 x arrières + 4 x avants/4 x arrières + 2 x av ants)

BIOS
AWARD legal Bios.
Supporte APM1.2.
Supporte ACPI
Supporte la Fonction USB.

Système d’Exploitation
Offre les meilleures perf ormances pour MS-DOS, Windows 2000, Windows
Me, Windows XP, SCO UNIX etc.

Dimensions
Facteur de Forme Micro ATX: 19.5cm X 22.8cm (l X L) (seulment pour
v ersion 1.x et 6.x)
Facteur de Forme Micro ATX: 19.5cm X 24.4cm (l X L) (seulment pour
v ersion 3.x, 4 5.x, 5.A, 5.B et 7.x)
.x,

Contenu de l'Emballage
Câble de Disque Dur
Câble de Lecteur de Disquette
Manuel d’utilisation
Câble USB (Optionnel)
Panneau d’E/S Arrière (Optionnel)
CD de Pilote Complet

26


Dépannage
PROBLÈME SOLUTION
Pas d'alimenta tion au système. Les * Assurez-v ous que le câble
v oyants lumineux ne s'allument pas, le d'alimentation e bien branché
st
v entilateur à l'intérieur du bloc * Remplacez le câble
d'alimentation ne se me pas en marche.
t
Le v o ant du clavier ne s'allume pas
y * Contactez le serv ice d'assistance
technique.
Le système nef onctionne pas. Les * En exerçant une pression uniforme sur
v oyants du cla vier sont allumés, les les deux extrémités du DIMM, poussez
v oyants de l'alimentation aussi, le disque le module vers le bas jusqu'à ce qu'il
dur tourne. s'enclenche.
Le système ne se réinitialise pas du * Vérif iez le câble du disque à la carte du
disque dur, réinitialisation possible contrôleur de disque. Assurez-v ous
depuis le lecteur lecteur optique. que les deux extrémités sont bien
branchées ; vérif iez le type de lecteur
dans la conf iguration standard de
CMOS.
* Il est très important d'effectuer des
sauv egardes du disque dur. Les
disques durs peuv ent tomber en panne
à n'importe quel moment.
Le système ne se réinitialise que depuis * Effectuez une sauv egarde des f ichiers
le lecteur optique. Le disque dur peut être des données et d'application.
lu et les applications sont utilisables mais Ref ormatez le disque dur. Ré-installez
il est impossible d'effectuer de les applications et les données
réinitialisation depuis le disque dur. sauv egardées sur les disques de
secours.
Un message s'affiche indiquant que la * Vérif iez l'équipement du système.
conf iguration n'est pas valide ou qu'il y a Assurez-v ous que les informations de
une panne du CMOS. la con iguration sont correctes.
f

Impossible de réinitialiser le système * Réglez les cav aliers maître/esclave
après l'installation d'un deuxième disque correctement.
dur. * Exécutez le programme SETUP et
sélectionnez le ty pes de lecteur.
s
Contactez les fabricants pour tou te
question de compatibilité avec les
autres disques.

27


Chapter 3: WarpSpeeder™

3.1 Introduction
[Warp Sp eeder™], a new p owerful control utility, features three
user-friendly functions includin g Overclock M anager, Overvoltage
M anager, and Hardware Monitor.
With the Overclock M anager, users can easily adjust the frequency
they p refer or they can get the best CPU p erformance with just one
click. The Overvoltage Manager, on the other hand, help s to p ower
up CPU core voltage and M emory voltage. The cool Hardware
M onitor smartly indicates the temp eratures, voltage and CPU fan
sp eed as well as the chip set information. Also, in the About p anel,
y ou can get detail descriptions about BIOS model and chip sets. In
addition, the frequency status of CPU, memory, AGP and PCI along
with the CPU sp eed are sy nchronically shown on our main p anel.
M oreover, to p rotect users' computer sy stems if the setting is not
approp riate when testing and results in sy stem fail or han g,
[Warp Sp eeder™] technology assures the sy stem stability by
automatically rebooting the co mputer and then restart to a sp eed that
is either the original sy stem sp eed or a suitable one.

3.2 S ystem Requirement
OS Sup p ort: Windows 98 SE, Windows M e, Windows 2000,
Windows XP
DirectX: DirectX 8.1 or above. (The Windows XP op erating system
includes DirectX 8.1. If you use Windows XP, you do not need to

28


install DirectX 8.1.)
3.3 Installation
1. Execute the setup execution file, and then the followin g dialo g
will pop up . Please click “Next” button and follow the default
p rocedure to install.

2. When y ou see the following d ialo g in setup p rocedure, it means
setup is completed. If the “Launch the WarpSp eeder Tray
Utility” checkbo x is checked, the Tray Icon utility and
[WarpSp eeder™] utility will be automatically and immediately
launched after y ou click “Finish” button.

29


Usage:
The following figures are just only for reference, the screen p rinted in this
user manual will ch an ge accordin g to y our motherboard on hand.

30


[WarpSpeeder™] includes 1 tray icon and 5 panels:
1. Tray Icon:
Whenever the Tray Icon utility is launched, it will display a
little tray icon on the right side of Windows Taskbar.

This utility is resp onsible for conveniently invoking
[Warp Speeder™] Utility. You can use the mouse by clickin g
the left button in order to invoke [WarpSp eeder™] directly
from the little tray icon or y ou can right-click the little tray
icon to pop up a p op up menu as followin g figure. The
“Launch Utility ” item in the p op up menu has the same
function as mouse left-click on tray icon and “Exit” item
will close Tray Icon utility if selected.

2. Main Panel
If y ou click the tray icon, [WarpSp eeder™] utility will be
invoked. Please refer to the followin g figure; the utility ’s
first window y ou will see is M ain Panel.
Main Panel contains fe ature s as follows:
a. Disp lay the CPU Sp eed, CPU external clo ck, M emory clock,
AGP clock, and PCI clock information.
b. Contains About, V oltage, Overclock, and Hardware M onitor
Buttons for invoking resp ective p anels.
c. With a user-friendly Status Animation, it can rep resent 3

31


overclock p ercentage stages:
M an walking→overclock percentage from 100% ~ 110
%
Panther running→overclock p ercentage from 110% ~
120%
Car racin g→ov erclock p ercentage from 120% ~ above

3. Voltage Panel
Click the V oltage button in M ain Panel, the button will be
high lighted and the V oltage Panel will slide out to up as the
followin g figure.
In this p anel, y ou can decide to increase CPU core voltage
and M emory voltage or not. The default setting is “No”. If
you want to get the best p erformance of overclock in g, we

32


recommend y ou click the op tion “Yes”.

4. Overclock Panel
Click the Overclo ck button in Main Panel, the button will be
high lighted and the Overclo ck Panel will slid e out to left as
the following figure.

33


O ve rclock Panel contains the these features:
a. “–3MHz button”, “-1M Hz button”, “+1MHz button”, and
“+3MHz button”: p rovide user the ability to do real-time
overclock adjustment.
Warning:
Manually overclock is potentially dangerous, especially when the overclocking
percentage is over 110 %. We strongly recom mend you verify every speed you
overclock by c lick the Verify button. Or, you can just click Auto overclock button
and let [WarpS peeder™ ] automatically gets the best result for you.
b. “Recovery Dialog button”: Pop up the following d ialo g. Let user
select a restoring way if sy stem need to do a fail-safe reboot.

34


d. “Auto-overclock button”: User can click this button and
[Warp Sp eeder™] will set the best and stable p erformance
and frequency automatically. [Warp Speeder™] utility will
execute a series of testing until sy stem fail. Then system
will do fail-safe reboot by using Watchdo g function. After
reboot, the [Warp Sp eeder™] utility will restore to the
hardware default setting or load the verified best and stable
frequency accordin g to the Recovery Dialo g’s setting.
e. “Verify button”: User can click this button and
[Warp Sp eeder™] will p roceed a testing for current
frequency. If the testing is ok, then the current frequency
will be saved into system registry. If the testing fail,
system will do a fail-safe rebootin g. After reboot, the
[Warp Sp eeder™] utility will restore to the hardware
default setting or load the verified best and stable
frequency accordin g to the Recovery Dialo g’s setting.
Note:
Because the testing programs, invoked in Auto-overclock and Verify, include
DirectDraw, Direct3D and DirectShow tests, the DirectX 8.1 or newer runtime
library is required. And please make sure your display card’s color depth is
High color (16 bit) or True color( 24/32 bit ) that is required for Direct3D
rendering.

5. Hardware Monitor Panel
Click the Hardware M onitor button in Main Panel, the
button will be highlighted and the Hardware Monitor p anel
will slide out to left as the following figure.
In this p anel, y ou can get the real-time status information of
your system. The information will be refreshed ev ery 1
second.

35


6. About Panel
Click the “about” button in M ain Panel, the button will be
high lighted and the About Panel will slide out to up as the
followin g figure.
In this p anel, y ou can get model name and detail
information in hints of all the chip set that are related to
overclockin g. You can also get the mainboard ’s BIOS model
and the V ersion number of [Warp Sp eeder™] utility.

36


Note:
Because the overclock, overvo ltage, and hardware monitor
features are controlled by several separate chip set,
[WarpSp eeder™] divide these features to sep arate panels. If one
chip set is not on board, the correlative button in M ain p anel will
be disabled, but will not interfere other p anels’ functions. This
p rop erty can make [Warp Sp eeder™] utility more robust.

37


06/29/2004

38

Manual de tarjeta madre- U8668

Manual de tarjeta madre- U8668

Recommandé

Recommandé

Contenu connexe

En vedette

En vedette (11)

Similaire à Manual de tarjeta madre- U8668

Similaire à Manual de tarjeta madre- U8668 (20)

Plus de Itachi354

Plus de Itachi354 (16)

Dernier

Dernier (20)

Manual de tarjeta madre- U8668