2. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
Powering ON the Aircraft
Battery Switch ON/Guard
Emergency Exit Lights Guard
No Smoke/Chime ON/Guard
Packs / Air Conditioning Both OFF
Aircraft Lights
Logo As Required
Position Steady
Wing As Required
Wheel Well As Required
Weight and Balance
Fuel, payload As Required
GPU Connected
Ext Air Conditioning As required
Aircraft Doors
Entry (FWD and AFT) Open
Cargo (FWD and AFT) Open
Catering access (FWD and AFT) Open
Airstair As required
Ground Power Switch ON
IRS Switch Both on NAV
Lights Test and Adjustments Optional
3. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
Cabin Preparation Flow Part 1
Fire Panel Left (hold)
Emergency Exit Lights Fault/Inop
Emergency Exit Lights Ovht / Fire (hold)
Fire Warning Bell Cutout Push
Master Caution Check for Ovht
Fire Bottles Circuit Check Test 1 and 2
Oxygen Check Check
Radio Setup
Tune ATIS Altimeter
Tune ATC Plan approval
Squalk Code Set
MCDU/FMC Setup Next page...
4. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
MCDU / FMC Setup / Preflight
IDENT
Model / Eng Rating / AIRAC Check
POS INIT
Ref Airport Set
Set Initial POS Set
ROUTE
Origin / Destination Set
Route and RWY Set
PERF INIT
ZFW Set
Reserves Set
Cost Index Set
Cruize Alt Set
Transition Altitude Set
N1 Limit
Select DERATE As required
Assumed TEMPERATURE As required
TAKE-OFF
T/O Flaps Set
C.G. Set
Take-off Speeds Set
5. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
Cabin Preparation Flow Part 2
Stabilizer Trim Set
MCP Setup
Flight Director L and R “ON”
Indicated Air Speed Set to V2
Heading As required
Altitude As required
After Overhead Scanflow
Flaps and Slats Status LEDs Test
PSEU Light Off
Service Interphone Off
Engine Reserve Lights Off
EEC On and guard
Passenger Oxygen Switch Guard
Flight Recorder Test / Guard
Mach Airspeed warning test (1 and 2) Push
Stall warning test (1 and 2) Push
6. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
Overhead Scanflow
Flight Controls, Alternate Flap and Spoiler Switch Guard
Yaw Damper ON
Navigation Switches Normal
Display Switches Auto / Normal
Fuel Temperature (> -40C and <40C ) Check
Cross Feed Valve Open / Close
Electric Panel Check
Standby Power and Drives switches Guard
Equip Cooling switches Normal
Windows Heat On
Hydraulic Electric pumps On
Check Hydraulic display Fluid and Pressure
Hydraulic Electric pumps Off
Cockpit Voice Recorder Test
Pressurization Gauges Check
Trim air On
Packs Panel
Recirculation Fans (L/R) Auto
Packs (Air Cond) Keep OFF
Isolation Valve Auto
Engine Bleeds ON
APU bleed OFF
Flight/Cruize Altitude Set
Landing Altitude Set
Pressurization Mode Auto
7. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
Main panel scanflow
Master Caution Push
EFIS Panel Set
MCP Navigation Selection As required
Display Units Switches Norm
A/P – A/T – FMC Lights Test
Standby Instruments Check
Auto Brake RTO
Parking Brake Apply/Set
8. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
Engines Start
Fuel Pump (AFT #1) On
APU Start Switch Start
APU Gen 1 & 2 On
***EXECUTE THE PREFLIGHT CHECKLIST***
Ground Power Remove
Ground Air Conditioning (if connected) Remove
Packs (Air Cond) As Required
Wheel Chocks Remove
CDU left seat pilot Takeoff page
CDU right seat pilot LEGS page
GPWS Test
TCAS Test
Fuel Pumps (all) ON
Hydraulic Electric Pumps ON
Packs L/R (Air Cond) – if hot weather only R OFF
APU Bleed ON
Anti Colision Light ON
***EXECUTE THE BEFORE START CHECKLIST***
Parking Brake Release
Push back Request
Eng START Switch #2 Ground
Eng STAR Lever #2 (after #2 N2 pass 22%) Idle
Eng START Switch #1 Ground
Eng STAR Lever #1 (after #1 N2 pass 22%) Idle
9. This guide is intent for FLIGHT SIMULATION ONLY – do not use it for flight.
From the COLD and DARK panel STATE
After start and taxi flow
Probe Heat ON (both)
Packs (Air Cond) AUTO
Engines GEN 1 and 2 ON
APU OFF
Engine start switches CONT
FLAPS Set for T/O
Flight Controls Check
Taxi light ON
***EXECUTE THE BEFORE TAXI CHECKLIST***
Proceed to the taxi
***EXECUTE THE BEFORE TAKEOFF CHECKLIST***
Proceed to the HOLD position (before the runway)
Take Off lights setup
Fixed landing lights ON
Taxi lights OFF
Position Lights Strobe & Steady
Auto Throttle ARM
Transponder / Squalk TA/RA
11. “This is a NOT copyrighted material. Feel free to
change, publish, modify, increase and put in your
trash without restrictions”
“Happy is thew one that
transfers what you knows and
learn from what teaches”