2. NETWORK THEOREMS
• KIRCHHOFFS LAWS
• MESH ANALYSIS
• NODAL ANALYSIS
• NORTAN
• SUPERPOSITION
• THEVENIN
• MAXIMUM POWER TRANSFER
3. Kirchhoff's Laws
Kirchhoff's circuit laws are two equalities that deal with
the conservation of charge and energy in electrical circuits.
There basically two Kirchhoff's law :-
1. Kirchhoff's current law (KCL) – Based on principle of
conservation of electric charge.
2. Kirchhoff's voltage law (KVL) - Based on principle of
conservation of energy.
4. Kirchhoff's current law (KCL)
This law is also called Kirchhoff's first law, Kirchhoff's point
rule, Kirchhoff's junction rule (or nodal rule), and Kirchhoff's
first rule.
The principle of conservation of electric charge implies that:
At any node (junction) in an electrical circuit, the sum
of currents flowing into that node is equal to the sum of
currents flowing out of that node, or The algebraic sum of
currents in a network of conductors meeting at a point is zero.
Strictly speaking KCL only applies to circuits with steady
currents (DC).
However, for AC circuits having dimensions much smaller
than a wavelength, KCL is also approximately applicable.
5. The current entering any junction is equal to the
current leaving that junction. i1 + i4 =i2 + i3
Recalling that current is a signed (positive or negative)
quantity reflecting direction towards or away from a
node, this principle can be stated as:
I 0
6. Kirchhoff's voltage law (KVL)
This law is also called Kirchhoff's second law, Kirchhoff's loop
(or mesh) rule, and Kirchhoff's second rule.
The principle of conservation of energy implies that
The directed sum of the electrical potential
differences (voltage) around any closed circuit is zero, or
More simply, the sum of the emfs in any closed loop is
equivalent to the sum of the potential drops in that loop
Strictly speaking KVL only applies to circuits with steady
currents (DC).
However, for AC circuits having dimensions much smaller than
a wavelength, KVL is also approximately applicable.
7. The algebraic sum of the products of the resistances of the
conductors and the currents in them in a closed loop is equal
to the total emf available in that loop. Similarly to KCL, it can
be stated as:
KVL: Vn 0
Vemf I R OR loop
The sum of all the voltages around the loop is equal to
zero. v1 + v2 + v3 - v4 = 0
8. Mesh Analysis
Mesh analysis (or the mesh current method) is a method that
is used to solve planar circuits for the currents (and indirectly
the voltages) at any place in the circuit. Planar circuits are
circuits that can be drawn on a plane surface with
no wires crossing each other.
Mesh analysis works by arbitrarily assigning mesh currents in
the essential meshes. An essential mesh is a loop in the circuit
that does not contain any other loop.
9. Steps to Determine Mesh Currents:
1. Assign mesh currents i1, i2, .., in to the n meshes.
Current direction need to be same in all meshes
either clockwise or anticlockwise.
2. Apply KVL to each of the n meshes. Use Ohm’s
law to express the voltages in terms of the mesh
currents.
3. Solve the resulting n simultaneous equations to
get the mesh currents
11. Apply KVL to each mesh. For mesh 1,
V1 R1i1 R 3 ( i1 i2 ) 0
( R1 R 3 ) i1 R 3i2 V1
For mesh 2,
R 2 i2 V2 R 3 ( i2 i1 ) 0
R 3 i1 ( R2 R 3 ) i2 V2
12. Solve for the mesh currents.
R1 R3 R3 i1 V1
R3 R2 R3 i2 V2
Use i for a mesh current and I for a branch
current. It’s evident from Fig. 3.17 that
I1 i1 , I2 i2 , I3 i1 i2
13. Nodal Analysis
In electric circuits analysis, nodal analysis, node-voltage
analysis, or the branch current method is a method of
determining the voltage (potential difference) between
"nodes" (points where elements or branches connect) in
an electrical circuit in terms of the branch currents.
Nodal analysis is possible when all the circuit elements
branch constitutive relations have an admittance
representation.
Kirchhoff’s current law is used to develop the method
referred to as nodal analysis
14. STEPS FOR NODAL ANALYSIS:-
• Note all connected wire segments in the circuit. These are
the nodes of nodal analysis.
• Select one node as the ground reference. The choice does not
affect the result and is just a matter of convention. Choosing
the node with most connections can simplify the analysis.
• Assign a variable for each node whose voltage is unknown. If
the voltage is already known, it is not necessary to assign a
variable.
• For each unknown voltage, form an equation based on
Kirchhoff's current law. Basically, add together all currents
leaving from the node and mark the sum equal to zero.
15. • If there are voltage sources between two unknown
voltages, join the two nodes as a super node. The
currents of the two nodes are combined in a single
equation, and a new equation for the voltages is
formed.
• Solve the system of simultaneous equations for each
unknown voltage.
16. 1. Reference Node
500 500
+
I1 V 1k 500 I2
500
–
The reference node is called the ground node
where V = 0
17. Example
500 500
V1 V2 V3
1 2 3
I1 1k 500 I2
500
V1, V2, and V3 are unknowns for which we solve
using KCL
18. Steps of Nodal Analysis
1. Choose a reference (ground) node.
2. Assign node voltages to the other nodes.
3. Apply KCL to each node other than the reference
node; express currents in terms of node voltages.
4. Solve the resulting system of linear equations for
the nodal voltages.
23. Superposition Theorem
• It is used to find the solution to networks with two or more
sources that are not in series or parallel
• The current through, or voltage across, an element in a linear
bilateral network is equal to the algebraic sum of the currents
or voltages produced independently by each source.
• For a two-source network, if the current produced by one
source is in one direction, while that produced by the other is in
the opposite direction through the same resistor, the resulting
current is the difference of the two and has the direction of the
larger
• If the individual currents are in the same direction, the
resulting current is the sum of two in the direction of either
current
24. Superposition Theorem
• The total power delivered to a resistive element must be
determined using the total current through or the total voltage
across the element and cannot be determined by a simple sum
of the power levels established by each source
For applying Superposition theorem:-
• Replace all other independent voltage sources with a short
circuit (thereby eliminating difference of potential. i.e.
V=0, internal impedance of ideal voltage source is ZERO (short
circuit)).
• Replace all other independent current sources with an open
circuit (thereby eliminating current. i.e. I=0, internal impedance
of ideal current source is infinite (open circuit).
25. Example:- Determine the branches current
using Superposition theorem.
6 2
i1 i3
120 V i2 3 i4 4 12 A
Figure 1
Solution:
• The application of the superposition theorem is shown in
Figure 1, where it is used to calculate the branch current. We
begin by calculating the branch current caused by the voltage
source of 120 V. By substituting the ideal current with open
circuit, we deactivate the current source, as shown in Figure
2.
26. 6 v1 2
i'1 i'3
120 V i'2 i'4 4
3
Figure 2
• To calculate the branch current, the node voltage across
the 3Ω resistor must be known. Therefore
v1 120 v1 v1
=0
6 3 2 4
where v1 = 30 V
The equations for the current in each branch,
27. 120 30
i'1 = = 15 A
6
30
i'2 = = 10 A
3
30
i'3 = i'4 = =5A
6 6 2
i 1" i 3"
i 2" 3 i4" 4 12 A
In order to calculate the current cause by the current source, we
deactivate the ideal voltage source with a short circuit, as shown
28. To determine the branch current, solve the node
voltages across the 3Ω dan 4Ω resistors as shown in
Figure 4
6 2
+ +
v3 3 v4 4 12 A
- -
v3 v3 v3 v4
=0
3 6 2
v4 v3 v4
12 = 0
2 4
The two node voltages are
29. • By solving these equations, we obtain
v3 = -12 V
v4 = -24 V
Now we can find the branches current,
30. To find the actual current of the circuit, add the currents due to
both the current and voltage source,
31. Thevenin's theorem
Thevenin's theorem for linear electrical networks states that
any combination of voltage sources, current
sources, and resistors with two terminals is electrically
equivalent to a single voltage source V and a single series
resistor R.
Any two-terminal, linear bilateral dc network can be replaced
by an equivalent circuit consisting of a voltage source and a
series resistor
32. Thévenin’s Theorem
The Thévenin equivalent circuit provides an equivalence at
the terminals only – the internal construction and
characteristics of the original network and the Thévenin
equivalent are usually quite different
• This theorem achieves two important objectives:
– Provides a way to find any particular voltage or current
in a linear network with one, two, or any other number
of sources
– We can concentration on a specific portion of a network
by replacing the remaining network with an equivalent
circuit
33. Calculating the Thévenin equivalent
• Sequence to proper value of RTh and ETh
• Preliminary
– 1. Remove that portion of the network across which
the Thévenin equation circuit is to be found. In the
figure below, this requires that the load resistor RL be
temporarily removed from the network.
34. – 2. Mark the terminals of the remaining two-
terminal network. (The importance of this step will
become obvious as we progress through some
complex networks)
– RTh:
– 3. Calculate RTh by first setting all sources to zero
(voltage sources are replaced by short circuits, and
current sources by open circuits) and then finding
the resultant resistance between the two marked
terminals. (If the internal resistance of the voltage
and/or current sources is included in the original
network, it must remain when the sources are set to
zero)
35. • ETh:
– 4. Calculate ETh by first returning all sources to their
original position and finding the open-circuit voltage
between the marked terminals. (This step is
invariably the one that will lead to the most
confusion and errors. In all cases, keep in mind that
it is the open-circuit potential between the two
terminals marked in step 2)
36. • Conclusion:
– 5. Draw the Thévenin
equivalent circuit with Insert Figure 9.26(b)
the portion of the circuit
previously removed
replaced between the
terminals of the
equivalent circuit. This
step is indicated by the
placement of the resistor
RL between the terminals
of the Thévenin
equivalent circuit
37. Another way of Calculating the Thévenin
equivalent
• Measuring VOC and ISC
– The Thévenin voltage is again determined by
measuring the open-circuit voltage across the
terminals of interest; that is, ETh = VOC. To determine
RTh, a short-circuit condition is established across the
terminals of interest and the current through the
short circuit Isc is measured with an ammeter
– Using Ohm’s law:
RTh = Voc / Isc
38. Example:- find the Thevenin equivalent
circuit.
5 4
a
+ +
25 V 3A v1 vab
20
- -
b
Solution
• In order to find the Thevenin equivalent circuit for the circuit
shown in Figure1 , calculate the open circuit voltage, Vab. Note
that when the a, b terminals are open, there is no current flow
to 4Ω resistor. Therefore, the voltage vab is the same as the
voltage across the 3A current source, labeled v1.
• To find the voltage v1, solve the equations for the singular node
voltage. By choosing the bottom right node as the reference
node,
39. v1 25 v1
3 0
5 20
• By solving the equation, v1 = 32 V. Therefore, the Thevenin
voltage Vth for the circuit is 32 V.
• The next step is to short circuit the terminals and find the
short circuit current for the circuit shown in Figure 2. Note
that the current is in the same direction as the falling voltage
at the terminal.
5 4 a
+ +
25 V 3A v2 vab isc
20
- -
b
Figure 2
40. Current isc can be found if v2 is known. By using the bottom
right node as the reference node, the equationfor v2 becomes
By solving the above equation, v2 = 16 V. Therefore, the short
circuit
current isc is
v2 25 v2 v2
3 0
5 20 4
The Thevenin resistance RTh is
Figure 3 shows the Thevenin equivalent circuit for the Figure 1.
42. Norton theorem
Norton's theorem for linear electrical networks states that
any collection of voltage sources, current
sources, and resistors with two terminals is electrically
equivalent to an ideal current source, I, in parallel with a
single resistor.
Any two linear bilateral dc network can be replaced by an
equivalent circuit consisting of a current and a parallel
resistor.
43. Calculating the Norton equivalent
• The steps leading to the proper values of IN
and RN
• Preliminary
– 1. Remove that portion of the network across
which the Norton equivalent circuit is found
– 2. Mark the terminals of the remaining two-
terminal network
44. • RN :
– 3. Calculate RN by first setting all sources to zero
(voltage sources are replaced with short circuits, and
current sources with open circuits) and then finding
the resultant resistance between the two marked
terminals. (If the internal resistance of the voltage
and/or current sources is included in the original
network, it must remain when the sources are set to
zero.) Since RN = RTh the procedure and value
obtained using the approach described for Thévenin’s
theorem will determine the proper value of RN
45. Norton’s Theorem
• IN :
– 4. Calculate IN by first returning all the sources to
their original position and then finding the short-
circuit current between the marked terminals. It is
the same current that would be measured by an
ammeter placed between the marked terminals.
– Conclusion:
– 5. Draw the Norton equivalent circuit with the
portion of the circuit previously removed replaced
between the terminals of the equivalent circuit
46. Example
Derive the Norton equivalent circuit
Solution
Step 1: Source transformation (The 25V voltage source
is converted to a 5 A current source.)
5 4
a
25 V 3A
20
b
4
a
5A 5 20 3A
b
47. Step 2: Combination of parallel source and parallel resistance
4
a
8A 4
b
Step 3: Source transformation (combined serial resistance to
produce the Thevenin equivalent circuit.)
8
a
32 V
b
48. • Step 4: Source transformation (To produce the Norton
equivalent circuit. The current source is 4A (I = V/R = 32
V/8 ))
a
4A 8Ω
b
Norton equivalent circuit.
49. Maximum power transfer theorem
The maximum power transfer theorem states that, to
obtain maximum external power from a source with a finite
internal resistance, the resistance of the load must be equal
to the resistance of the source as viewed from the output
terminals.
A load will receive maximum power from a linear bilateral
dc network when its total resistive value is exactly equal to
the Thévenin resistance of the network as “seen” by the
load
RL = RTh
50. Resistance network
which contains
dependent and
independent sources
• Maximum power transfer happens when the load
resistance RL is equal to the Thevenin equivalent
resistance, RTh. To find the maximum power delivered to
RL ,
2 2
V Th R L V Th
pmax = 2
=
2R L 4R L
51. Application of Network Theorems
• Network theorems are useful in simplifying analysis of some
circuits. But the more useful aspect of network theorems is
the insight it provides into the properties and behaviour of
circuits
• Network theorem also help in visualizing the response of
complex network.
• The Superposition Theorem finds use in the
study of alternating current (AC) circuits, and semiconductor
(amplifier) circuits, where sometimes AC is often mixed
(superimposed) with DC