Kuhn 6200 landsman

A note to our customers, parts managers and dealers:
This manual has been prepared to assist you in the proper use, daily care, and operation of
your new Kuhn Krause equipment. It contains specific information on the many built--in
features of your equipment, the accessories and options that are available, general
specifications, and instructions for making minor adjustments.
Read this manual carefully before operating your Kuhn Krause equipment, and keep it in a
convenient location for later reference.
In order to ensure that you have the most current owner’s manual available for your
implement, we have added a revision code to each manual. Please note the information
listed below and specify when placing service calls or ordering parts.
Manual for Model: TL 6200
This manual covers models beginning with Serial No. 1001
Owner’s Manual #: 6200--1
Parts Manual #: 6200--2
Rev.:
ISSUED TO: ISSUED BY:
Owner’s Name Kuhn Krause Dealer
Mailing Address City
City State
State Date of Purchase
Printed JAN12 SN 2551

KUHN KRAUSE WARRANTY STATEMENT
(Kuhn Krause Serial Numbered Wholegoods purchased subsequent to May 1, 2008)
Note: This warranty is limited to the equipment and parts sold in North America and all
warranty work must be accomplished by a Kuhn Krause, Inc. Authorized Service
Center rated to perform maintenance on Kuhn Krause Products.
A. KUHN KRAUSE, INC. (“KRAUSE”) LIMITED WARRANTY.
(1) Subject to the limitations and conditions hereinafter set forth, Kuhn Krause warrants, at the time of
delivery by Kuhn Krause to be free from (i) defects in materials or workmanship, and (ii) defects in
design that in the view of the state of the art as of the date of manufacture should have been foreseen
provided, however, that the defect must be discovered and reported to Kuhn Krause within the periods
specified as follows. For a period of one year all new serial numbered production agricultural units
covered by this warranty; for a period of thirty--six (36) months the tongue weldment, center frame
weldment, wing frame weldments, disc harrow gang bearings and K--Tine field cultivator shanks.
(2) Kuhn Krause does not warrant disc blades, shanks, hydraulic cylinders, accessories and other parts
not manufactured by it, but supplied with or as a part of its products. Kuhn Krause will, however,
obtain and pass on any adjustments provided by the manufacturers of such parts under these
manufacturer’s warranties. Tires supplied on Kuhn Krause products, will be warranted by the tire
manufacturer’s retail outlets.
(3) The entire extent of Kuhn Krause’s liability shall be limited to that of either reimbursing Buyer for
its costs of purchasing a rebuilt, over--hauled or repaired part from either Kuhn Krause or a proper
Kuhn Krause Authorized Service Center or, at Kuhn Krause’s election, reimbursing buyer for its costs
of having the part repaired at a proper Kuhn Krause Authorized Service Center. If Kuhn Krause elects
not to repair the part and if neither a rebuilt, over--hauled or repaired part is, in Kuhn Krause’s
opinion, timely available then Kuhn Krause will reimburse buyer for its costs of purchasing a new part
from either Kuhn Krause or a proper Kuhn Krause Authorized Service Center. The labor necessary
to remove from the product such part or parts and to install in the product such part or parts, as well
as any repair made as the result of improper installations by Kuhn Krause, shall be covered by this
warranty, provided the work is performed at a proper Kuhn Krause Authorized Service Center.K If
return of the defective part is required, it must be returned shipping prepaid to Kuhn Krause, Inc.
Kuhn Krause’s limited warranty will apply to any part repaired or replaced by a proper Kuhn Krause
Authorized Service Center pursuant to Kuhn Krause’s Limited Warranty: however, the applicable
warranty for such part repaired or replaced shall be limited to the unexpired portion of Kuhn Krause’s
Limited Warranty described in paragraph (1) or (2) above, as applicable. In other words, the warranty
period of the part repaired or replaced does not start over from the date of reinstallation.
K[Kuhn Krause, Inc. will repair or replace, free of charge, any part of the product found to be defective,
within the specified warranty periods, after an inspection of the part has deemed it to be defective.
Inspection must be performed by an authorized agent of Kuhn Krause, Inc. or returned to the Kuhn
Krause factory for inspection and disposition. Warranty labor will be considered during the first year
of warranty only. Kuhn Krause, Inc. will establish and publish an hourly flat rate for shop labor and
reimbursement during the first year of the warranty period. Kuhn Krause does not allow credit for the
cost of travel time, mileage or hauling as a warranty allowance. During the remaining second and third
year, when applicable, Kuhn Krause will repair or replace the defective part, without consideration of
labor charges.]
(4) Routine services (such as inspections, field settings, adjustments, etc.) and replacement of items which
deteriorate from expected normal wear and tear or exposure (such as paint, tires, hoses, blades,
sweeps, points, shank wear strips, etc.) are not covered by this Limited Warranty. Such routine
services and replacements required during the course of operation are not considered to be the result
of any defect in the product.

B. LIMITATIONS APPLICABLE TO KUHN KRAUSE’S LIMITED WARRANTY.
(1) Kuhn Krause, Inc. will be relieved of all obligations and liability under this warranty if:
(i) The alleged defect in the part is due to misuse or neglect on the part of someone other than Kuhn
Krause; or
(ii) Kuhn Krause’s identification mark or name or serial number has been removed from the part in
question; or
(iii) The product and/or equipment have not been maintained, operated or stored either in accordance
with applicable manuals, communications or other written instructions of Kuhn Krause or any
manufacturer of the part involved, or in accordance with applicable regulations and advisory
circulars unless buyer shows that such maintenance, operation or storage was not a contributory
cause of the defect; or
(iv) The part in question has been modified or altered after delivery other than by the manufacturer
or in accordance with a modification or alternation scheme approved in writing by the
manufacturer; or
(v) The product is used for purposes other than conventional owner/operator usage. Usage not
considered conventional owner/operator includes, but is not limited to, operation conditions that
consist of rocks or other obstructions.
(2) For the purpose of this Warranty, no part of the product or equipment will be regarded as breaching
the limited warranty merely because, subsequent to its delivery, some modification or alteration
becomes necessary for product improvements or in order to meet a change in the requirements of any
applicable regulation.
(3) TO THE EXTENT ALLOWED BY APPLICABLE LAW, BUYER WAIVES AS TO KUHN KRAUSE ALL
OTHER WARRANTIES, WHETHER OF MERCHANTABILITY, FITNESS OR OTHERWISE, THERE
ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACT HEREOF.
(4) TO THE EXTENT ALLOWED BY APPLICABLE LAW, THE OBLIGATIONS OF KUHN KRAUSE
SET FORTH HEREIN SHALL BE THE EXCLUSIVE REMEDIES FOR ANY BREACH OF
WARRANTY HEREUNDER, AND, TO THE SAME EXTENT, KUHN KRAUSE SHALL NOT BE
LIABLE FOR ANY GENERAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, ANY DAMAGES FOR DIMINUTION OF MARKET VALUE, LOSS OF
USE OR LOSS OF PROFITS, OR ANY DAMAGES TO THE PRODUCT CLAIMED BY BUYER OR
ANY OTHER PERSON OR ENTITY UPON THE THEORIES OF NEGLIGENCE OR STRICT
LIABILITY IN TORT.
(5) ANY ACTION BY BUYER FOR BREACH OF THIS WARRANTY BY EITHER KUHN KRAUSE OR
SELLER MUST BE COMMENCED WITHIN (1) YEAR AFTER THE CAUSE OF ACTION ACCRUES.

Establishing Customer Warranty
Customer’s Obligation
1. The customer is responsible for reading the operation manual supplied with each serial
numbered unit. The manual describes the safe and correct operating procedures of the specific
product. The operation manual will also instruct the user on recommended lubrication and
maintenance of the product.
2. The customer will advise the dealer of the anticipated start date of the product so a dealer
representative can be on hand to make necessary field adjustments.
3. The owner is also responsible for inspecting the product during and after use. If a part has failed
or is in need of repair, it should be replaced. When continued use of the product would result in
excessive wear of other components, the part should be replaced before operation is continued.
Continued use of the product may void warranty on other parts damaged from this condition.
The user must make the machine available to the dealer for a warranty repair.
4. It is the customer’s responsibility to deliver his machine to an authorized Kuhn Krause dealer
for completion of a warranty repair. If the dealer agrees to make a service trip to the customer’s
residence, it is an agreement between the dealer and the customer. Kuhn Krause will not allow
warranty credit for the cost of travel, mileage, or hauling.
5. Warranty labor consideration will only be given during the first year of warranty. Any labor
charge for the 2nd or 3rd year on the limited warranty will be at the customer’s expense.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.

1
TL 6200 SERIES LANDSMAN
DEALER PREDELIVERY CHECK SHEET
TO BE CHECKED BY DEALER
CUSTOMER DATE
ADDRESS COUNTY
DEALER
ADDRESS COUNTY
MODEL NUMBER SERIAL NUMBER
DEALER CHECK:
1. Check to see that all rocker shaft bolts are tight and pins are in place.
2. Check to see that hydraulic cylinders are full of oil (air bled out of cylinders). Clevis pins with
hairpin clips should be in place. Models TL 6200--9, TL 6200--12, TL 6200--15 require 6
Quarts / 5.76 Liters of oil; Models TL 6200--18 and TL 6200--21 require 20 Quarts / 19 Liters
of oil; Models TL 6200--24 and TL 6200--27 require 24 Quarts / 22.7 Liters of oil; Model TL
6200--31 will require 34 Quarts / 32.2 Liters of oil, and Model TL 6200--36 will require 51
Quarts / 48 Liters of oil; Models TL 6200--42 and TL 6200--45 require 55 Quarts / 52 Liters.
3. Examine hydraulic hoses to see that they are protected from damage.
4. Bolts attaching the walking tandem to the wheel arms should be tight. Check to see that
bearings have been adjusted and greased.
5. Check lug bolt holding wheels to the hub to see that they are properly torqued (6 bolt wheel
120 Ft. Lbs.; 8 bolt wheels to 170 Ft. Lbs.)
6. See chart below for correct size tires and their locations. Inflate all tires to the following
pressures:
MODEL CENTER SECTION WING SECTION
TL 6200--09 (4) 9.5L x 15, 8--Ply inflated to 44 PSI -- -- N/A -- --
TL 6200--18 (4) 11L x 15, 12--Ply inflated to 52 PSI (4) 9.5L x 15, 8--Ply inflated to 44 PSI
TL 6200--21 (4) 11L x 15, 12--Ply inflated to 52 PSI (4) 9.5L x 15, 8--Ply inflated to 44 PSI
TL 6200--24 (4) 11L x 15 FI, 6--Bolt inflated to 90 PSI (4) 11L x 15, 8--Ply inflated to 36 PSI
TL 6200--27 (4) 12.5FI, 8--Bolt inflated to 90 PSI (4) 11L x 15, 8--Ply inflated to 36 PSI
7. Check to see that bolts and pins attaching hitch frame and clevis weldment to hitch are in
place and tightened.
8. Jack should be operational for support of tongue when implement is not attached to a tractor.
9. Road lock and wing lock are engaged and operate satisfactorily.
10. Restrictors are installed in wing lift cylinder rod end ports.
11. All decals are in place per page P80--P81 of this owner’s manual.
12. Customer review sheet is filled out and signed.
13. A safety chain is provided with a strength rating equal to or greater than the gross weight of
the TL 6200 with attachments.
14. Review lighting requirements. Light kits are standard.
15. Check to see that the Owner’s Manual is in the storage tube on the implement.
16. Check to see that the SMV Sign is clean and in place.
DELIVERED BY:
DATE:

3
Contents Rev. 10/10
WARRANTY
DEALER PREDELIVERY CHECK SHEET 1
CUSTOMER REVIEW SHEET 2
TABLE OF CONTENTS 3
SPECIFICATIONS 4
GENERAL INFORMATION DRAWING 5
OPERATING SECTION
PROTECT YOURSELF FROM CHEMICALS O2
SAFETY DECALS / INFORMATIVE DECALS O3--O4
ABOUT YOUR LANDSMAN O5
PREPARING FOR OPERATION O5
PREPARING THE TRACTOR O6
HYDRAULIC SAFETY O6
Disc Gangs O7
HITCHING TO THE TRACTOR O7
UNHITCHING LANDSTAR FROM TRACTOR O8
Transporting O9
Transport Lock Valves O9
Raising and Lowering the Wings O9
Transport Safety O10
Hitch Pin O10
FIELD ADJUSTMENTS O11
Tongue Height Adjustment O11
Depth of Disc Blades O12
Scrapers O13
Sweeps O13
Working Depth O13
Hydraulic Depth Control O13
Flexibility O13
Turning in the Field O13
Hydraulic Disc Gangs O14
STORAGE SUGGESTIONS O14
GENERAL INFORMATION O14
SERVICING O14
General Maintenance O14
Lubrication O15
Wheel Bearings O15
Walking Beams O15
Disc Gangs O15
Repair Parts O16
PROCEDURE TO LOCATE INTERNAL LEAKS O17
Test Cases 1 through 5 O17--O19
TROUBLESHOOTING SECTION O20--O21
HYD. GANG TROUBLESHOOTING SECTION O22
MODEL 6336 WING FOLD SEQUENCE VALVE O23
PARTS SECTION
SMV & LIGHT KIT BRACKET ASSEMBLY P1
MAIN FRAME (Models TL6200 9, 12, 15) P2
MAIN FRAME (Models TL6200, 18, 21, 24) P3
MAIN FRAME (Models TL6200 27,31,36,42,45) P4
CENTER ROCKER (Models TL6200 9,12,15) P6--P7
CENTER ROCKER (Models TL6200 18,21,24) P8--P9
CENTER ROCKER (Models TL6200 27 thru 45) P10--P11
RIGID TONGUE (Models TL6200 9 thru 24) P12--P13
RIGID TONGUE (Models TL6200 27 thru 45) P14--P15
CUSHION TONGUE (Models TL6200 9 thru 45) P16--P17
WING FRAMES (MODEL TL6200 18 thru 31) P18--P19
WING ROCKER (MODEL TL6200 18 thru 31) P20--P21
WING FRAMES & ROCKERS (TL6200--36) P22--P23
WING FRAMES (TL6200 42 & 45) P24--P25
WING ROCKERS (TL6200 42 & 45) P26--P27
WALKING BEAM ASSEMBLIES P28--P29
WHEELS & TIRES P30
TIE RODS P31
DISC GANG & BEARING ARM ASSEMBLY P32--P33
2 PIECE K--TINE SHANK ASSEMBLIES P34--P35
SPRING SHANK ASSEMBLY P37
WING LIFT GROUP (TL6200 -- 18 thru 31) P38--P39
INSIDE/OUTSIDE WING LIFT (TL6200--36) P40--P41
INSIDE/OUTSIDE WING LIFT (TL6200--42,45)) P42--P43
DEPTH VALVE ASSEMBLY P44
HYD. HOSE STAND & LOCK VALVE BRACKET P45
HYDRAULICS (MODELS TL6200 9,12,15) P46--P47
HYDRAULICS (MODEL TL6200 18,21) P48--P49
HYDRAULICS (MODELS TL6200 24) P50--P51
HYDRAULICS (MODEL TL6200 27,31) P52--P53
HYDRAULICS (MODEL TL6200 36) P54--P55
HYDRAULICS (MODELS TL6200 42,45) P56--P59
HYDRAULIC HOSE W/PLASTIC GRIP ASS’M. P60
PRINCE CYLINDER 4--1/2“ x 32” P61
PRINCE CYLINDER 4--1/4” X 10” P62
PRINCE CYLINDER 4” X 10” P63
PRINCE CYLINDER 3--3/4” X 10” P64
PRINCE CYLINDER 5” x 32” P68
PRINCE CYLINDER 2” X 5--7/8” P69
CYLINDER SUPPORT ASSEMBLY P70
DISC GANG HYDRAULIC HOSE & FITTINGS P71
PACKER HITCH ASSEMBLY P72
HYDRAULIC DISC GANG PLACEMENTS P73--P79
DECALS & REFLECTORS P80--P81
LIGHT KIT P82
REAR RECEPTACLE PARTS P83
ASSEMBLY SECTION
GENERAL ASSEMBLY INSTRUCTIONS A1
CENTER FRAME ASSEMBLY A2
TONGUE ASSEMBLY A4
WALKING BEAM ASSEMBLY A5
SELF SUPPORTING CENTER SECTION A5
WING FRAMES & ROCKERS A5
WING FOLD ASSEMBLY A7
GANG BEAMS -- SCRAPER BAR A8
UNASSEMBLED GANGS/REPAIR SEQUENCE A9--A10
DISC SCRAPERS, EXTENSIONS, SHANKS A11--A12
HYDRAULICS ASSEMBLY A12
DISC GANG HYDRAULICS ASSEMBLY A14
DECALS, LIGHT KIT & FINAL CHECK A14--A15
PLACEMENT DRAWINGS FOR MODELS:
TL 6200 -- 09 A18--A21 TL 6200 -- 27 A42--A45
TL 6200 -- 12 A22--A25 TL 6200 -- 31 A46--A49
TL 6200 -- 15 A26--A29 TL 6200 -- 36 A50--A53
TL 6200 -- 18 A30--A33 TL 6200 -- 42 A54--A57
TL 6200 -- 21 A34--A37 TL 6200 -- 45 A58--A61
TL 6200 -- 24 A38--A41
PARTS INDEX Index 1--7

O2
PROTECT YOURSELF FROM CHEMICALS AND PESTICIDES
SUGGESTED PROTECTIVE GEAR:
1. HARD HAT: Should be washable, have a brim to collect chemicals. Replace headband if
contaminated. Wash entire unit daily.
2. GOGGLES AND FACE SHIELD: Protect eyes, face. Goggles should fit snuggly, comfortably.
Shield should cover entire face.
3. RESPIRATOR: To prevent inhaling of chemical dust vapors. Use canisters specified for
chemicals being used. Replace canisters as specified.
4. GLOVES: Rubber with long sleeves so cuff can be made. Unlined is best ---- cloth linings are
hard to wash and decontaminate.
5. APRON / SMOCK: Protects clothing from splashes, spills. Smock gives more body protection.
Wash or replace as needed.
6. COVERALLS: Wear as outer layer for easy removal, if contaminated. Tight knit, closable at
neck, wrists. Wash when contaminated.
7. RUBBER BOOTS: Protect against spills on your regular boots or shoes. Important because
leather is hard to decontaminate.
NOTE: DIRTY, CONTAMINATED OR IMPROPERLY WORN PROTECTIVE CLOTHING AND
EQUIPMENT MAY BE AS BAD AS USING NO SAFETY GEAR AT ALL. FOLLOW THESE
LAUNDERING INSTRUCTIONS.
Change all clothing daily.
Keep clothing contaminated (worn while handling, applying) with pesticides separate from other
family laundry. Keep it in a plastic bag if it is not washed immediately.
Use hot water (140_ Fahrenheit) and fill machine to normal full level. Do not overload clothing.
Use recommended amount of a heavy--duty phosphate--type detergent.
Dry clothing immediately after washing, preferably in an automatic clothes dryer.
PESTICIDES AND CHEMICALS CAN ENTER YOUR BODY IN SEVERAL WAYS, SO IT IS
ESSENTIAL TO WEAR A PROTECTIVE BARRIER WHILE HANDLING THEM. THE MOST
CRITICAL AREAS NEEDING PROTECTION ARE YOUR EYES, SKIN AND LUNGS.
DON’T SMOKE OR EAT UNTIL AFTER THOROUGHLY WASHING WITH SOAP AND WATER.
USE COMMON SENSE.

O5
OPERATING INSTRUCTIONS
Do not allow anyone to operate this implement who has not been trained in
its safe operation. Read all safety decals on the implement, and review the
safety first suggestions on the back cover of this manual to refresh your
memory. Watch for the safety symbol and read the information. This is for
your own protection. If you do not understand any safety decal or
instructions in this manual, contact your dealer for assistance.
ABOUT YOUR LANDSMAN
This Landsman Tillage tool has been designed for one--trip secondary tillage. Hinged wing
sections, spring--loading of the disc gangs, shanks and attachments make it flexible enough to
follow the contour of most field conditions. Wings will float down 7_ and up 20_. It is designed to
be used for seed bed preparation and chemical incorporation, with a maximum working depth of 6
inches. The Landsman works best at field speeds of 5 to 7--1/2 M.P.H., however, rocky conditions
may require a slower field speed. Horsepower requirements, will generally be 6 to 8 drawbar
horsepower per foot of cut. Kuhn Krause offers five different attachments for finish tillage: three
rows of tines followed by reels, three rows of tines, four rows of tines, 5 rows of spikes or 3 rows of
spikes followed by reels. Caution should be used in adding any other rear attachment that will add
weight to the unit.
Caution: Adding of excess additional weight could cause frame or axle
failures resulting in loss of control during transport.
PREPARING THE LANDSMAN FOR OPERATION
1. The wings should be down and implement lowered to the ground. All hydraulic cylinders should
be pinned and full of oil.
Caution: Lower the implement to the ground before making the following
inspections. With the implement lowered, enter the framework by
stepping over, do not crawl under the framework. If the implement
is not lowered, any hydraulic failure could cause the implement to
drop suddenly, causing personal injury.
2. The maintenance lock stops pinned to the storage brackets.
3. Check for loose bolts and tighten if needed. Check again for loose bolts after the first half day
of operation.
4. Check disc gangs for tight tie rod nuts and clinched cotter pins.
5. Check the shank locations, and attachment locations with the placement diagram to be sure
unit has been set--up properly.
6. Make sure that all grease zerk locations have been sufficiently greased. Grease zerks will be
found on the rocker shaft bearings, walking beams, wheel hubs and hinges.
7. Check tire pressure. Inflate all tires: 9.5L x 15, 8--Ply to 44 P.S.I.
11L x 15, 8--Ply to 36 P.S.I.
12.5 FI, 8--Bolt, to 90 P.S.I.
Caution: Frequently check to see that the wheel lug bolts are properly
torqued (6 bolt wheel 120 Ft. Lbs.; 8 bolt wheels to 170 Ft. Lbs)
particularly during the initial transport and operation of the tillage
tool. The bolts may work loose, resulting in the loss of a wheel and
subsequent loss of control of the tractor and / or implement.
8. Check and adjust tightness of wheel bearings and walking beams before operation, after the
first week, and periodically thereafter. (See service section on page O15)

O6
PREPARING THE TRACTOR
Read your tractor owner’s manual. It will describe safe methods of operation. Make sure your
tractor has proper added ballast, and that its hydraulic system is full of oil and working properly.
Check tractor brakes and warning lights, make sure that they are in working order.
HYDRAULIC SAFETY (PLEASE READ CAREFULLY)
If the implement hydraulic system has never been used, stored over a period of time or disassembled
for any reason, unpin the rod ends of the cylinders and support the cylinders so the rod ends will clear
frame members when fully extended. Back the tractor to the front of the implement and connect the
hydraulic hoses. Check the tractor hydraulic reservoir and make sure it is full of the manufacturer’s
recommended oil. If you are sure the implement hydraulic hose connections are tight, begin filling the
system by extending and retracting the cylinders. Hold the control lever open and pause at the end
of each stroke to bleed the air from the system. Continue the cycles until the cylinders respond with
immediate solid actuation. When you are sure the systems are free of air, pin the rod ends of the
cylinders to the implement cylinder lugs.
Warning: Escaping fluid under pressure can penetrate the skin causing serious
injury. Avoid the hazard by relieving pressure before disconnecting
hydraulic lines. Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands and body
from high pressure fluids.
If an accident occurs, see a doctor immediately. Any fluid injected into
the skin must be surgically removed within a few hours or gangrene
may result.
AVOID HEATING NEAR PRESSURIZED HYDRAULIC HOSES
Flammable spray can be generated by heating near pressurized hydraulic hoses, resulting in
severe burns to yourself and bystanders. Do not heat by welding, or using a torch near hoses.
Hose can be accidentally cut when heat goes beyond the immediate flame area.
THE FOLLOWING WARNINGS PERTAIN TO THE MORE COMMON ABUSES OF HYDRAULIC HOSE:
1. INSPECT the hose assembly before each use. 3. DO NOT EXCEED the maximum recommended working pressure
2. REPLACE the hose assembly immediately if: of the hose.
a) The jacket of the hose appears abnormal. 4. DO NOT KINK the hose assembly.
b) You have reason to believe it may be abnormal. 5. DO NOT BEND the hose assembly beyond its minimum bend radius
c) There is any fluid leakage. of 3.25 inches.
d) The couplings are damaged. 6. DO NOT EXPOSE to temperatures in excess of 225_ Fahrenheit.
e) The hose is damaged or kinked. 7. DO NOT USE AS A STRENGTH MEMBER for pulling or lifting
f) The reinforcement is visible through the jacket. equipment.
Caution: If replacing hydraulic hose, use only hose that meets of exceeds
3,000 PSI working pressure.
IMPORTANT: REPAIR OF HYDRAULIC CYLINDERS SHOULD BE MADE BY AN
AUTHORIZED KUHN KRAUSE DEALER.
Prevent damage to trail hoses by supporting them from the tractor
with an elastic strap “A” . Avoid having excess hose
between the implement support “B” and the tractor
connection “C” . Either reposition the hose farther back
on the implement or request a shorter hose from your
dealer.
Inspect the hydraulic system for tell--tale leaks and loose fittings.
Tighten if needed. When assembling your hydraulic system, if JIC and O--Ring fittings and hoses are
to be used, the use of a tape or liquid sealer is not necessary. MAKE SURE a restrictor (identified
with a tag) is installed in the rod end port of the wing lift cylinder.

O7
Caution: Air in hydraulic system will allow implement or wings to drop
suddenly.
Warning: Do not operate the hydraulics until you have read “Hydraulics” in
the service section of this manual.
The Landsman is equipped with two separate hydraulic systems; one to control the wheels, and the
other to raise and lower the wing for transport.
Wheels ---- Models 6200--18 Through 6200--45
Two master cylinders are mounted in the center on the main rocker shaft and they in turn are
connected to a slave cylinder on each wing. Each cylinder in this system is a rephasing
cylinder. This means there is an internal bypass in each cylinder that will let oil circulate when
the cylinder is extended to its maximum stroke. All lift cylinders should work together. If
cylinders are out of phase, hold the tractor valve open to extend the cylinder rod. Hold valve
open until all cylinders reach their maximum stroke, then continue to hold valve open for an
additional 20 to 30 seconds.
Wings
The wing lift cylinders are plumbed together. In some conditions, one wing may lift before the
other, this is normal. The wings will fold and unfold slowly, because of the restrictor in the rod
end of each wing cylinder. Make sure these restrictors are installed in the rod end port of the
wing lift cylinders. See pages P46--P59. If not previously filled, your hydraulic system will
require approximately: 6 Quarts / 5.76 Liters for Models TL 6200 9, 12 and 15; 20 Quarts / 19
Liters for Models TL 6200 18 and 21. 24 Quarts / 22.7 Liters for Models TL 6200 24 and 27.
Model TL 6200 31 will require approximately 34 Quarts / 32.2 Liters of oil. Model TL 6200 36
will require approximately 51 Quarts / 48 Liters of oil. Models TL 6200 42 and 45 will require
approximately 55 Quarts / 52 Liters of oil.
Use oil recommended by your tractor manufacturer. Read the service section “HYDRAULIC
SAFETY” on page O6 before filling the system. See “Hydraulic Cylinders Service Manual” for
additional information.
Disc Gangs
The optional hydraulic cylinders in this system are all rephasing and each is the same size and
stroke. If the cylinders are not moving in unison, or one cylinder is lagging behind the system is
“out--of--phase”. To rephase the cylinders simply raise the disc gangs completely and hold the
tractor lever open for 30--45 seconds. This will allow oil to bypass through the rephasing
grooves in each cylinder and bring all cylinders back into phase. All cylinders should now
operate in unison. Repeat the raise--hold cycle anytime that the cylinders are “out--of--phase”.
HITCHING AND UNHITCHING
Caution: Do not allow any person to stand between the tractor and the
implement while backing into position. Sudden loss of control
could cause serious injury or death to a person caught between the
tractor and implement. Tell your helper to wait until you signal that
the tractor is in park or neutral and the hand
brake is set and engine is shut off.
Note: Hydraulic hose grips are color coded as shown below.
Black / Black Lower Unit. . . . . . Red / Black Raise Unit. . . . . . . .
Yellow / Yellow Lower Wings. . . . Red / Yellow Raise Wings. . . . . . .
Gray / Gray Lower Disc Gangs. . . . . . . . Red / Gray Raise Disc Gangs. . . . . . . .

cart.3
cart.25
O15
Caution: Be sure gang is locked with a tie rod wrench on the opposite end
before force is applied.
Lubrication
The initial lubrication of all grease fittings will assure long life and satisfactory
performance from the implement. Use a multi--purpose type grease at all grease zerk
locations after each 24 hours of operation. Rocker shaft bearing clamps will accept
grease more efficiently if the whole unit is lowered to the ground with the weight of the
unit removed from the wheels. Other points of lubrication are: wing hinges, walking
tandem bearings, and wheel hubs. Disc gang bearings should be greased with a
high quality multi--purpose type grease after each use and after long periods of
storage. FLUSH ROLLING REELS WITH GREASE DAILY.
For Your Safety: When lubricating or adjusting your Landsman, watch for
obstructions or protrusions. Lower implement to the ground and
enter framework by stepping over. DO NOT walk on tires.
Wheel Bearings
Grease wheel bearings every 24 hours of use. Check for excessive end play each time that the
bearings are greased. Once a year, clean and repack the wheel bearings with EP#2 Grease.
Replace seals each time that the bearings are removed. Replace any worn or damaged parts.
Use light oil on the seal surface and use extreme care when pushing seal over the spindle.
Install outer bearings, flat washer, and slotted nut. Then back off nut from 1 to 2 slots until hub
turns freely without end play. Secure nut with clinched cotter pin.
Walking Beam
Grease the walking beam every 24 hours of use. When greasing the bearings, lower the unit
onto the points or sweeps and raise the walking beams off the ground. Check each walking
beam for any slack in the pivot bearings. When slack is found, tighten the axle nut until slack is
eliminated and tighten 5 to 10 Ft. Lbs. of preload on the bearings. DO NOT BACK THE AXLE
NUT OFF. Check, clean, and repack the walking beam bearings each year in a procedure that
is similar to that of wheel bearings.
Disc Gangs
Refer to the Assembly Section of this manual when replacing the blades, bearings or spools.
Use the same procedure as described when setting up a new unit. Leave bearing bolts one
turn loose until bearing arms are in place on the frame. Tighten tie rod to 1,000 Ft. Lbs.
Tighten one bearing arm to the frame then tighten its bearing bolts. Make sure the other
bearing arm top plate is parallel with the bottom of the frame before tightening its U--Bolts.
Tighten other bearing bolts. See pages A9--A10 for further details.
Maintenance locks have been provided for use when changing out disc blades. Fully extend the
cylinders and fasten the channel shaped locks onto both center rocker cylinder rods.
IMPORTANT: Rocker damage can occur if one lock is on the other lock is off.
Warning: Due to their sharpness and weight, serious injury can be inflicted
by disc blades and gangs if not handled safely. Watch for unsafe
conditions. Keep co--workers safety in mind. Should personal
injury occur, have medical treatment administered immediately.

P49
HYDRAULIC HOSE GROUP
FOR MODELS -- TL 6200 18 & 21 SEP07
Item Part Number Part Description Qty.
1 4881--77--0 1/2” DIA. x 96” Hose & Grip Assembly -- Red/Black Grip (see
Hydraulic Hose & Grip Assembly for parts details)
1
2 4881--71--0 1/2” DIA. x 96” Hose & Grip Assembly -- Black/Black Grip (see
1
3 24--2115R 3/8” DIA. x 156” (JIC) Black 2W Hose Assembly 2
5 25--2535 Depth Valve Assembly 1
6 4881--70--0 3/8” DIA. x 96” Hose & Grip Assembly -- Red/Yellow Grip (see
1
7 4881--76--0 3/8” DIA. x 96” Hose & Grip Assembly -- Yellow/Yellow Grip (see
1
8 25--301 3/4(M)O--Ring to 3/4(M)JIC 90_ Hydraulic Fitting 12
10 62--635 3/8NF x 5/8” GD5 Cap Screw 4
11 25--127 3/4” I.D. Hose Clamp 20
12 25--128 Hose Wraplock (Use where required)
14 21--181 4” x 24” Prince Hydraulic Cylinder Assembly 2
15 4956--75--0 O--Ring 37_ Flare 90_ Restrictor Assembly w/ Tag 2
17 25--303 37_ Flare 3/4(M) Tee Hydraulic Fitting 4
19 3127--83--1 Hose Clamp 2
21 62--692 3/8NF x 1” GD5 Cap Screw 3
24 62--343 1/2NC x 2” GD5 Cap Screw 2
25 21--1007 4” x 10” Series Hydraulic Cylinder Assembly 2
26 21--1006 3--3/4” x 10” Prince Series Hydraulic Cylinder Assembly 2
27 6118--0--1 Hose Bracket 2
28 63--106 1/2NC Hex Nut 2
29 64--107 1/2” STD. Lock Washer 2
34 25--126 34” Black Stay Strap (use as needed) -- not shown 6
35 25--2272 Check Valve -- Manual Release 2
36 25--300 3/4(M)O--Ring to 3/4(M)JIC Adapter Hydraulic FItting 2
37 25--314 3/4(M)O--Ring to 3/4(F)JIC Swivel Adapter Hydraulic Fitting 2

P51
FOR MODELS -- TL 6200 24 SEP07
1 4881--77--0 1/2” DIA. x 96” Hose & Grip Assembly -- Red/Black (see Hydraulic
Hose & Grip Assembly for parts details)
1
2 4881--71--0 1/2” DIA. x 96” Hose & Grip Assembly -- Black/Black (see Hydraulic
1
6 4881--70--0 3/8” DIA. x 96” Hose & Grip Assembly -- Red/Yellow (see Hydraulic
1
7 4881--76--0 3/8” DIA. x 96” Hose & Grip Assembly -- Yellow/Yellow (see
1
10 62--635 3/8NF x 5/8” GD5 Cap Screw 4
11 25--127 3/4” I.D. Hose Clamp 20
12 25--128 Hose Wraplock (Use where required) 2
19 3127--83--1 Hose Clamp 2
21 62--692 3/8NF x 1” GD5 Cap Screw 3
24 21--1007 4” x 10” Prince Series Hydraulic Cylinder Assembly 2
27 25--300 3/4(M)O--Ring to 3/4(M)JIC Adapter Hydraulic Fitting 2
33 25--126 34” Black Stay Strap (use as needed) -- not shown

P53
1
1
3 24--299R 3/8” DIA. x 162” Black 2W Hose Assembly 2
4 62--635 3/8NF x 5/8” GD5 Cap Screw 5
5 25--127 3/4” I.D. Hose Clamp 22
9 25--301 3/4(M)O--Ring to 3/4(M)JIC 90 Hydraulic Fitting 11
11 25--126 34” Black Stay Strap (use as needed) Spec.
14 25--303 37 Flare 3/4(M) Tee Hydraulic Fitting 4
16 4956--75--0 O--RIng 37 Flare 90 Restrictor Assembly w/ Tag 2
20 3127--83--1 Hose Clamp 2
22 62--692 3/8NF x 1” GD5 Cap Screw 3
23 21--1007 4 x 10” Prince Series Hydraulic Cylinder Assembly 2
1
30 4881--76--0 3/8” DIA. x 96” Hose & Grip Assemby -- Yellow/Yellow (see Hydrau-
lic Hose & Grip Assembly for parts details)
1
32 25--314 3/4(M)O--Ring--3/4(F)JIC Swivel Adapter Hydraulic Fitting 2

P55
FOR MODELS -- TL 6200 36 SEP07
1
1
1
4 4881--76--0 3/8” DIA. x 96” Hose & Grip Assembly -- Yellow/Yellow (see Hydraulic
1
12 25--2535 Depth Valve 1
15 25--309 O--Ring 37_ Flare Tee Hydraulic Fitting 1
18 3775--75--0 O--Ring 37_ Flare Tee Restrictor (25--306) w/ Tag 2
20 4956--75--0 O--Ring 37_ Flare 90_ Restrictor Fitting w/ Tag 4
24 25--324 37_ Flare M/F In--Line Restrictor Hydraulic Fitting 1
29 24--263R 3/8”DIA. x 228” (JIC) Black 2W Hose Assembly 1
30 25--127 3/4” I.D. Hose Clamp 34
31 62--635 3/8NF x 5/8” GD5 Cap Screw 8
32 62--692 3/8NF x 1” GD5 Cap Screw 3
34 21--1008 4--1/4” x 10” Prince Series Cylinder Assembly 2
35 21--1007 4” x 10” Prince Series Cylinder Assembly 2
36 21--1006 3--3/4” x 10” Prince Series Cylinder Assembly 2
37 25--126 34” Black Stay Strap (use as needed) -- Not shown 6
38 Wing Lift Hydraulic Cylinder Assembly (see Outside Wing Lift
Assembly for parts details)
2
39 25--310 3/4(M)JIC to 3/4(F)JIC 90_ Swivel Hydraulic Fitting 2
40 25--373 3/4 JIC Swivel Nut Branch Tee Hydraulic Fitting 1
41 25--144 Sequence Valve 3M PSI 1
42 25--1105 Snaplock Clamp (Bands Sequence Valve to Frame) 1
44 25--320 3/4(M)O--Ring to 37_ Flare 90_ (F) 3/4JIC Swivel Hydraulic Fitting 1
45 25--128 Hose Wrap Lock 2
46 25--2512 Check Valve, In--Line 1
47 6236--75--0 3/32 Restrictor w/ Tag 2

P57
HYDRAULIC HOSE GROUP -- ROCKERS
1
1
16 4809--0--2 Hose Bracket 6
17 25--303 37_ Flare Male Tee Hydraulic Fitting 2
19 21--1007 4” x 10” Prince Series Hydrauilc Cylinder Assembly 2
20 21--1006 3--3/4” x 10” Prince Series Hydraulic Cylinder Assemlby 2
21 64--103 3/8” STD. Lock Washer 42
22 63--311 3/8NC Hex Nut -- Black 42
23 62--635 3/8NF x 5/8” GD5 Cap Screw 3
24 63--112 3/4NC Hex Nut 2
25 64--112 3/4” STD. Lock Washer 2
26 62--108 3/8NC x 1” GD5 Cap Screw 2
27 62--421 3/4NC x 2” GD5 Cap Screw (not shown) 2
28 25--1153 5/8” I.D. Hose Clamp 10
29 25--304 37_ Flare Male Coupler Hydraulic Fitting 2
30 25--126 34” UV Black Stay Strap (Use as required) -- Not Shown Spec.
31 6345--0--2 Hose Clamp 10
32 61--275 U--Bolt, 3/8” DIA. x 3--1/16”W x 5--1/2”L 10

P59
HYDRAULIC HOSE GROUP -- WING FOLD
1
2 4881--76--0 3/8” DIA. x 96” Hose & Grip Assembly -- Yellow/Yellow (see Hydraulic
1
12 3775--75--0 O--Ring 37_ Flare Tee Restrictor Assembly w/ Tag 2
13 25--373 3/4 JIC Swivel Nut Branch Tee Hydraulic Fitting 1
14 25--324 37_ Flare M/F In--Line Restrictor Hydraulic Fitting 1
15 25--310 3/4(M)JIC to 3/4(F)JIC 90_ Swivel Hydraulic Fitting 2
17 25--144 Sequence Valve 3M PSI 1
18 25--1105 Snaplock Clamp (bands sequence valve to frame) 1
19 25--320 3/4(M)O--Ring to 37_ Flare 90_ (F) 3/4JIC Swivel Hydraulic Fitting 1
25 Hydraulic Wing Lift Cylinder Assembly (See Outside Wing Lift for 42’ &
45’ Models for parts detail)
2
27 62--692 3/8NF x 1” GD5 Cap Screw 3
28 25--127 3/4” I.D. Hose Clamp 9
29 25--1153 5/8” I.D. Hose Clamp 12
30 25--128 Hose Wrap Lock (not shown -- use as needed) Spec.
31 25--2512 Check Valve, In--Line 1

A1
ASSEMBLY INSTRUCTIONS
STUDY NAMES AND LOCATIONS OF THE PARTS AND FAMILIARIZE YOURSELF WITH THE
LANDSMAN BEFORE STARTING THE ASSEMBLY. READING THE STEP--BY--STEP
INSTRUCTIONS THAT FOLLOW WILL BE HELPFUL.
SAFETY
READ ALL OF THE SAFETY NOTATIONS IN THE ASSEMBLY
INSTRUCTIONS FOR YOUR PROTECTION. ACCIDENTS CAN BE
PREVENTED BY RECOGNIZING THE CAUSE OF AN ACCIDENT
BEFORE IT CAN HAPPEN.
ASSEMBLY AREA
Select an area for assembly that will be large enough to accommodate the completed implement.
The surface of the work area should be as level as possible. Leave room in front of the Landsman
to hook up to a tractor to charge the hydraulic system and fold the unit. Use the proper hand tools
to insure proper bolt tightness. Refer to the page titled ”Proper Bolt Use” for the recommended
torque values for different size bolts. Weights of major parts are MAIN FRAMES -- 1,600 LBS.;
MAIN ROCKER SHAFT -- 410 LBS., TONGUE -- 330 LBS.; therefore, stands will have to support
the combined weight of 2,500 Lbs. Make sure that the chains and handling equipment are
adequate for this weight.
PART LOCATIONS
FRONT -- the front of the frame can be determined by the location of the name plate that has been
attached to the front frame member.
RIGHT and LEFT sides can be established by standing behind the frame and looking toward the
front, or the direction of travel.
TOP -- To be sure that the frame is right side up, position the front hitch members of the frame
pointing down.
ASSEMBLY STEPS
Assemble the Landsman following the steps
shown in this section. Each step for part
attachment is reflected by a matching number
on the accompanying drawing or photograph.
Example:
Mount Bearing Arm 12 to each end of the Reel
Assembly. Assemble with 1/2NC x 1--1/2” GD5
Carriage Bolts, Lock Washers and Hex Nuts.
Make sure bearing grease zerk is in cut--out
provided.
MODEL NUMBER
Know the model number of the Landsman being
assembled. Use this model number whenever
referring to the assembly, parts listing pages or
placement pages. The number is stamped on the
Name Plate which is located on the front frame
member.
Refer to the Parts Illustration to identify the parts
during the assembly procedure. Read each step
through before beginning the actual assembly
process.

A7
C. Pin a 4” x 10” hydraulic cylinder to the Inner Wing cylinder bracket and the wheel arm. Pin a
3--3/4” x 10” hydraulic cylinder to the Outer Wing cylinder bracket and wheel arm. The rod
clevis should point up. Loosen both port plugs to allow the cylinder to extend.
D. Tighten all bolts; rocker must pivot freely.
E. Repeat Step III to install walking beams.
VII. WING FOLD ASSEMBLY
1. Models TL 6200 18 & 21 -- refer to illustration on page P38.
Models TL 6200 24, 27 & 31 -- refer to illustration on page P39.
A. Bolt (2) WING FOLD PLATES 3 to each side of the center frame with 3/4NC x 5” GD5
Bolts, Lock Washers and Hex Nuts. Do not tighten until cylinder clevis is in place.
B. Fasten a RIGHT and LEFT CYLINDER LUG 7 and 10 to the wing with 3/4NC x 5” GD5
Bolts, Lock Washers and Hex Nuts.
C. Models TL 6200 18 & 21 -- A 3/4NC x 6” GD5 Bolt and Flat Washer is inserted vertically
with a SQUARE WASHER 12 , Lock Washer and Hex Nuts on the bottom.
D. Model TL 6200 27 & 31 -- Clamp cylinder lugs to frame bar with 5/8” DIA. U--Bolt, Lock
Washers and Hex Nuts.
E. Pin base end of CYLINDER 4 between right and left cylinder lugs. The cylinder ports
should be on the back side on Models TL 6200 18 & 21, and on the top side for Models
TL 6200 24 thru 31. Retain cylinder with PIN 11 and 1/4” DIA. x 2--1/2” Roll Pins.
Models TL 6200 36, 42, 45: -- -- refer to illustration on page P40--41 (36’) or P42--43 (42’ & 45’).
A. Attach (2) FOLD PLATES 17 to center of unit with 3/4NC x 5”GD5 Bolts, Lock Washers, and
Hex Nuts.
B. Connect 5” x 32” HYDRAULIC CYLINDERS 20 with cylinder ports on the rear side of to fold
plates with PIN 12 and 1/4”DIA. x 2” Roll Pins.
C. Position WING LIFT BRACKET 6 on inner wings with U--Bolt 15 , Lock Washers and Hex
Nuts. Do not tighten.
TL 6200 36 ONLY: Go to illustration on page P40
D. Loosely attach FOLD STRAPS 5 and 16 to WING LIFT BRACKET 6 with 3/4NC x 6” GD5
Bolt, Lock Washer and Hex Nut.
Insert the base end of 4” x 30” CYLINDER 13 between wing lift bracket side plates and over the
cylinder lug welded on the outer wing frame and use PIN 15 with ROLL PINS 16 to secure it
into place.
E. Attach the ends of the FOLD STRAPS to the frame using (2) 3/4NC x 4--1/2” GD5 Bolts, Flat
Washers, Lock Washers and Hex Nuts.
TL 6200 42 & 45 ONLY: Go to illustration on page P42
F. Attach PLATE 16 (page P42) with 3/4NC x 6--1/2” Bolts, Lock Washers and Nuts. Pin base
end of 4--1/2” x 32” CYLINDER 13 with cylinder pin 16 .
IMPORTANT: FOLD STRAPS MUST BE IN TENSION DURING THE FOLD CYCLE. USE
FLAT WASHERS AS NEEDED TO ELIMINATE SLACK BETWEEN FRAME MEMBER AND
WING LIFT BRACKET. SEE ILLUSTRATION BELOW.

TL6400 PARTS INDEX Rev.DEC11
Part Number Page Item Part Number Page Item Part Number Page Item Part Number Page Item
1000-11540-0 P30 1 21-260 Cont'd P63 13 21-871 P68 8 24-268R P53 24
1000-11580-0 P30 6 P64 12 21-872 P68 9 P55 26
1000-12540-01 P30 1 21-266 P67 2 21-878 P65 5 P55 43
1000-95588-0 P30 6 21-286 P65 8 P66 5 P57 12
1112-0-7A P7 14 P66 7 P67 5 P59 7
1280-0-10 P33 38 P67 8 21-879 P65 6 24-279R P49 18
1483-286-1 P33 27 21-337 P63 4 P66 6 24-282R P57 15
1918-10-0 P33 37 P66 4 P67 6 24-283R P59 22
1918-14-0A P28 10 21-348 P64 4 21-887 P61 4 24-286R P55 8
1918-84-0 P28 2135-54-0 P17 30 21-888 P61 5 P55 27
1963-9-0 P33 50 P29 21-890 P61 7 P59 6
21-1006 P49 26 2136-82-1 P31 21-892 P61 19 24-288R P55 17
P51 25 P33 43 21-900 P67 1 24-291R P51 18
P53 18 21-381 P62 3 21-904 P65 1 24-299R P49 32
P55 36 P63 3 21-917 P68 1 P53 3
P57 20 P64 3 21-918 P68 2 P53 19
P64 A 21-404 P61 10 21-919 P68 3 24-311R P53 12
21-1007 P47 20 P62 11 2212-18-1 P31 P55 10
P49 25 P63 11 P33 43 P57 6
P51 24 P64 10 2212-18-2 P33 44 24-312R P47 12
P53 23 P65 11 2224-18-1 P31 24-325R P55 11
P55 35 P66 11 P33 43 P57 7
P57 19 P67 11 2225-18-1 P31 24-330R P60 2
P63 A P68 11 P33 43 P60 2
21-1008 P55 34 P41 11 2227-18-1 P31 24-338R P49 9
P57 18 P43 12 P33 43 P51 9
P62 A 21-443 P62 24 24-200R P47 15 24-359R P53 10
21-1027 P43 13 P63 24 P49 23 24-368R P53 6
P61 A P64 23 P51 23 P55 14
21-166 P69 A 2145-0-16 P11 11 24-207R P47 16 P57 10
P70 5 P9 17 P49 22 24-372R P47 5
21-181 P38 4 2145-0-6 P40 8 P51 13 P49 33
P49 14 P42 10 P51 22 P51 32
P65 A 2145-52-1 P11 4 24-2101R P51 31 24-389R P47 3
21-182 P39 4 2146-82-1 P31 24-2105R P60 2 24-390R P49 4
P51 14 P33 43 P60 2 P51 4
P53 17 21-507 P65 7 P60 2 24-503R P71 8
P67 A P67 7 P60 2 P78
21-185 P41 13 P68 19 24-2106R P59 26 P79
P66 A 21-526 P61 3 24-210R P49 16 24-504R P71 8
21-189 P40 20 P67 3 P59 20 P78
P42 18 21-702 P62 9 24-2114R P55 25 24-505R P71 8
P55 33 P63 9 24-2115R P49 3 P73
P59 24 P64 9 P51 29 P77
P68 A 21-738 P65 4 P57 14 P78
21-2013 P66 1 P67 4 24-2116R P53 15 P79
21-2046 P65 3 21-775 P66 2 24-2128R P55 28 24-506R P71 8
21-2059 P63 26 21-778 P66 3 24-213R P51 20 24-507R P71 8
21-2060 P62 26 21-803 P64 5 24-217R P51 16 24-508R P71 8
21-2061 P63 1 21-807 P63 12 P59 23 P77
P64 1 P64 11 24-221R P53 28 24-509R P71 8
21-2062 P62 1 21-808 P64 26 24-223R P49 30 P76
21-2063 P63 2 21-810 P63 5 24-225R P51 30 P77
21-2064 P64 2 21-819 P62 8 P53 21 P78
21-2065 P62 2 21-821 P69 24 24-228R P53 27 P79
21-2069 P62 12 21-833 P69 7 24-237R P49 31 24-510R P76
21-2072 P62 4 21-835 P69 8 P55 22 P78
21-2073 P62 5 21-836 P69 9 24-241R P51 3 24-511R P71 8
21-2074 P62 6 21-837 P69 10 24-243R P47 19 P73
21-2125 P62 7 21-841 P69 13 24-244R P47 17 P77
21-2126 P63 7 21-842 P69 14 P53 13 P78
P64 7 21-848 P69 22 24-248R P53 26 P79
21-2127 P62 10 21-855 P69 23 24-256R P49 13 24-512R P71 8
P63 10 21-857 P65 21 24-257R P49 20 P77
P64 25 P66 21 24-261R P53 25 24-513R P71 8
21-2145 P61 1 P67 20 P55 19 P73
21-2148 P61 6 21-858 P68 21 P57 11 P75
21-2165 P61 2 21-859 P61 8 2426-35-1 P7 5 24-514R P71 8
21-2212 P63 6 P65 9 P9 6 24-515R P71 8
21-2217 P64 6 P67 9 24-263R P55 29 P76
21-222 P65 2 21-865 P69 1 24-264R P55 16 24-516R P71 8
21-225 P63 8 21-868 P68 4 P59 10 P76
P64 8 21-869 P68 5 24-265R P55 9 P77
21-260 P62 13 21-870 P68 6 P57 13 P78
Index - 1

24-517R P71 8 25-2535 P44 15 25-593 P71 7 42-109 P29 6
P74 P47 7 P73 42-131 P29 7
P75 P49 5 P74 4218-13-2 P28 20
24-518R P71 8 P51 5 P75 4218-13-3 P28 4
24-519R P71 8 P53 8 P76 4226-0-10 P35 3
P74 P55 12 P77 4226-0-11 P35 4
P75 P57 8 P78 4237-58-0 P19 27
P76 25-2536 P44 17 P79 4260-80-1 P41 9
24-520R P71 8 25-2537 P44 16 30-104 P33 42 P43 9
P75 25-300 P47 21 30-208S P33 39 4260-80-3 P41 1
24-521R P71 8 P49 36 3112-105-0 P44 27 P41 5
P78 P51 27 3112-46-0 P33 24 P43 1
P79 P53 7 3112-47-0 P33 24 P43 5
24-522R P71 8 P55 7 3112-69-1 P44 20 4260-81-1 P41 8
P77 P57 5 3112-69-2 P44 21 P43 8
24-527R P71 8 P59 5 3113-54-0 P16 2 44-107 P11 29
P74 25-301 P47 11 31-179 P34 1 P7 37
2490-96-0 P29 25 P49 8 P35 1 P9 30
25-1105 P55 42 P51 8 31-180 P34 2 4809-0-2 P57 16
P59 18 P53 9 P35 2 4881-0000-3 P16 10
25-1153 P45 9 P55 13 3118-46-0 P33 24 P17 31
P57 28 P57 9 31-199 P37 1 4881-0000-5A P16 35
P59 29 P59 8 31-204 P34 16 P17 32
25-1163 P2 30 25-302 P55 23 P35 17 4881-0-2 P1 1
P3 1 P59 16 31-205 P37 2 4881-5040-0 P45 12
P5 15 25-303 P47 18 3127-30-1 P33 3 4881-70-0 P49 6
25-126 P49 34 P49 17 3127-571-1 P72 12 P51 6
P51 33 P51 17 3127-83-1 P38 16 P53 29
P53 11 P53 14 P39 16 P55 3
P55 37 P55 21 P49 19 P59 1
P57 30 P57 17 P51 19 P60 1
P73 P59 11 P53 20 4881-7086-0A P16 17
P74 25-304 P57 29 3131-157-0 P33 30 P17 33
P75 25-309 P55 15 3131-158-0 P33 30 4881-71-0 P47 1
P76 P59 9 3131-77-0 P38 13 P49 2
P77 25-310 P55 39 P39 13 P51 2
P78 P59 15 3131-84-1 P33 23 P53 2
P79 25-314 P47 22 32-101 P33 26 P55 2
P82 23 P49 37 32-103 P33 26 P57 2
P83 10 P51 28 33-109 P37 3 P60 1
P84 10 P53 32 33-198 P34 12 4881-74-0 P60 1
25-127 P45 14 P55 5 P35 13 P71 8
P49 11 P57 3 33-199 P34 12 P73
P51 11 P59 3 P35 13 P74
P53 5 25-320 P55 44 364-0-7 P33 41 P75
P55 30 P59 19 364-0-9 P33 36 P77
P59 28 25-324 P55 24 3755-0-16 P40 12 P78
25-128 P47 4 P59 14 P42 5 4881-75-0 P60 1
P49 12 25-373 P55 40 3755-12-2 P38 12 P71 8
P51 12 P59 13 3775-75-0 P55 18 P73
P55 45 25-385 P71 3 P59 12 P74
P59 30 P73 3950-0-2 P13 11 P77
25-144 P55 41 P74 P16 40 P78
P59 17 P75 3950-0-5 P33 35 4881-76-0 P49 7
25-221 P60 7 P76 40-109 P33 51 P51 7
25-2272 P47 6 P77 4100-961-1 P2 6 P53 30
P49 35 P78 41-112 P28 14 P55 4
P51 26 P79 P29 2 P59 2
P53 31 25-391 P71 4 41-113 P28 8 P60 1
P55 6 P79 41-114 P29 3 4881-77-0 P47 2
P57 4 25-392 P71 1 41-121 P28 2 P49 1
P59 4 25-393 P71 2 41-208 P28 3 P51 1
25-2278 P45 10 25-394 P71 5 P28 13 P53 1
25-2289 P60 4 P78 P29 4 P55 1
25-2290 P60 4 P79 41-209 P28 9 P57 1
P60 5 25-400 P71 6 41-210 P29 5 P60 1
25-2291 P60 4 P73 4122-0-78A P21 2 4881-9032-0 P16 5
P60 5 P74 4122-0-8A P7 24 P17 34
25-2295 P60 3 P75 4122-60-0 P19 12 4881-9035-1 P13 18
25-2510 P60 4 P76 P2 9 P16 11
P60 5 P77 P23 33 P17 35
25-2512 P55 46 P78 4200-190-1 P83 9 P15 16
P59 31 P79 P84 9 4885-0-5 P16 4
25-452 P79 42-108 P28 7 P17 36
Index - 2

4885-0-6 P16 3 5660-16-0 P25 23 61-107 P45 3 6127-212-0A P70 2
P17 37 5800-17-0 P11 26 61-115 P33 25 6127-25-0 P2 7
4885-75-0 P75 P7 34 6112-0-1 P2 5 P3 11
4956-56-0 P15 17 P9 27 6112-10-0 P7 20 P5 7
P17 38 595-0-11 P7 28 6112-105-0 P44 27 6127-28-0 P19 19
4956-75-0 P49 15 60-101 P13 26 6112-11-0 P7 19 6127-40-0B P5 4
P51 15 P15 2 6112-11-1 P7 16 6127-411-0 P72 8
P53 16 60-103 P11 27 6112-35-0 P2 3 6127-412-0 P72 7
P55 20 P7 35 6112-400-1 P72 4 6127-42-0A P42 1
P59 21 P9 28 6112-400-3 P72 18 P5 5
51-102 P30 7 60-106 P15 3 6112-40-0A P2 4 6127-454-0 P2 8
51-106 P30 7 P17 3 6112-401-0 P72 3 6127-48-0 P28 25
51-107 P30 4 60-114 P28 19 6112-410-0A P72 9 61-275 P57 32
P30 9 P29 10 6112-42-0 P19 11 6127-52-0 P28 24
51-132 P30 2 60-211 P44 24 6112-46-0 P33 24 P28 A
51-136 P30 2 60-605 P16 41 6112-47-0 P33 24 6127-52-1 P28 21
52-102 P30 8 60-606 P11 8 61-126 P19 28 6127-53-0 P28 A
52-103 P30 3 P13 15 P25 25 6127-54-0 P28 1
P30 8 P15 4 P39 12 6127-55-0 P28 1
52-114 P30 3 P17 4 P45 3 6127-70-0 P33 24
52-302 P28 18 P38 6 61-127 P45 3 6127-76-0 P13 9
52-302 P29 8 P39 6 61-143 P33 20 P16 29
53-102 P11 14 P40 11 P70 11 6127-77-0 P13 5
P21 7 P41 16 61-152 P1 3 P16 33
P23 10 P42 6 61-155 P25 18 6127-78-0 P13 2
P27 11 P43 17 6115-52-0 P33 24 P16 30
P7 7 60-608 P33 46 6115-53-0 P33 24 6127-79-0 P13 6
P7 25 P41 10 6118-0-1 P21 8 P16 34
P9 8 P43 10 P49 27 6127-80-0 P13 1
P9 13 P70 10 6118-0-3 P47 13 6127-83-0 P15 22
P9 24 60-614 P13 10 6118-10-0 P9 12 P17 40
53-103 P21 16 P16 27 6118-28-0 P19 20 6127-88-0 P19 9
53-105 P28 6 P19 8 6118-47-0 P38 3 P23 23
53-108 P29 9 P23 20 6118-52-0 P33 24 P25 4
53-109 P38 14 P25 7 6118-53-0 P33 24 6127-89-0 P21 15
P39 14 60-615 P13 29 6118-77-0 P13 8 P7 27
P40 10 P15 5 P16 28 6127-90-0B P33 A
P41 6 P17 5 6118-83-0 P13 14 6127-90-1 P33 5
P42 11 P33 34 P16 26 6127-90-2 P33 48
P43 6 60-616 P13 12 61-207 P2 27 6127-93-0 P33 10
53-110 P23 4 P16 38 6121-48-0 P33 24 6127-94-0B P33 8
P27 7 P17 6 6121-49-0 P33 24 P70 8
53-113 P15 1 60-617 P11 2 61-216 P1 3 6127-96-0 P33 1
P17 1 P7 9 P35 5 6131-46-0 P33 24
53-116 P13 16 P9 2 P82 10 6131-47-0 P33 24
P16 39 60-618 P41 2 61-217 P44 28 6131-48-0 P33 24
P43 15 P41 4 61-228 P33 13 6136-34-0A P23 26
53-127 P13 7 P43 2 P70 14 6136-50-5 P42 16
P16 22 P43 4 61-232 P19 2 6136-52-0A P29 26
53-142 P33 47 60-626 P16 43 P2 26 6136-57-1A P29 27
P70 9 P17 7 P23 27 6136-57-2A P29 24
53-148 P19 16 P33 7 P3 2 6136-70-0 P41 7
P23 34 60-632 P44 10 P40 15 P43 7
P25 15 60-702 P28 17 P42 15 6136-75-0A P29 1
53-166 P16 37 P29 11 61-241 P21 20 6136-76-0A P29 1
P17 2 60-703 P33 18 P23 17 6136-80-0 P41 3
53-169 P37 4 P45 13 P27 15 6136-86-0 P23 11
5630-0-12 P13 25 60-713 P33 45 6124-17-1 P11 28 P23 22
P15 18 60-716 P16 7 P7 36 P25 8
5630-0-2 P13 20 P17 8 P9 29 6139-51-0A P5 22
P15 19 P40 19 61-243 P44 28 6142-50-0 P33 24
5630-0-33 P1 1 P41 18 6124-43-0 P39 3 6142-52-0 P33 24
5630-0-34 P1 8 P42 14 6127-0-11 P11 9 6142-80-0 P15 23
5630-0-8A P45 1 P43 19 P15 21 6142-81-0 P15 24
5630-121-0A P37 21 60-725 P44 23 P17 39 P17 41
5630-122-0A P37 22 6100-0-1 P69 11 6127-0-14A P34 3 6142-82-0 P15 25
5630-124-0 P37 23 6100-208-0 P70 17 6127-0-15 P34 5 P17 42
5630-125-2 P37 24 6100-75-0 P73 6127-0-4 P38 10 6142-83-0 P15 26
5630-129-0 P37 19 P74 6127-0-5 P38 7 P17 43
5630-75-0 P15 20 P75 6127-0-9 P19 7 6150-454-0 P2 28
5635-0-2 P37 20 P76 P23 19 6155-450-1 P2 6
5635-123-0 P37 25 P77 P25 6 6200-0-1 P13 23
5635-125-1 P37 26 P78 6127-210-0C P70 1 P15 27
5635-125-2 P37 27 6110-46-0 P33 24 6127-210-1 P70 20 6200-1-0 P2 1
Index - 3

6200-143-0 P3 12 62-205 cont'd P42 9 62-474 P33 52 63-112 P11 16
6200-2-0 P2 2 P5 23 62-475 P44 22 P19 4
6200-42-0 P19 26 62-207 P19 5 P70 3 P2 21
P2 10 P2 22 62-486 P82 6 P21 5
P2 11 P23 28 62-493 P1 9 P23 9
P23 29 P3 3 62-507 P1 13 P25 13
P25 22 P38 17 P83 4 P27 5
6200-90-0 P16 8 P39 17 P84 4 P28 22
P17 44 P7 41 62-510 P45 11 P28 29
6201-0-3 P1 2 P72 6 62-546 P19 22 P3 5
6201-1-0 P3 13 62-210 P38 8 62-547 P37 8 P33 22
6201-30-0 P13 13 P40 7 62-562 P33 12 P38 1
6201-75-0 P7 1 P5 13 62-566 P2 25 P39 1
P9 1 P7 13 62-569 P16 23 P40 4
6201-76-0 P7 10 62-213 P29 12 P17 14 P42 7
P9 10 P42 17 P34 10 P5 18
6201-86-0 P9 23 P5 21 P35 9 P57 24
6202-0-1 P15 28 P72 5 62-606 P5 8 P7 22
P17 45 62-224 P72 10 P72 15 P70 13
6202-0-2 P15 29 62-234 P7 8 62-635 P44 1 P72 1
P17 46 P9 9 P49 10 P9 16
6202-1-0 P5 3 62-237 P11 20 P51 10 63-113 P16 42
6202-10-0 P11 15 P21 10 P53 4 P17 17
6202-18-0 P19 17 P23 12 P55 31 P29 14
6202-20-0 P19 17 P27 12 P57 23 63-114 P13 21
6202-30-0 P15 30 P7 6 62-656 P60 6 P15 9
6202-33-0 P15 31 P7 30 62-692 P49 21 63-117 P11 22
P17 47 P9 7 P51 21 P16 15
6202-36-0 P2 13 P9 25 P53 22 P17 17
6202-37-0 P2 12 62-250 P16 36 P55 32 P21 12
6202-4-0 P5 1 P17 11 P59 27 P23 14
6202-5-0 P5 2 62-253 P11 12 62-707 P34 6 P27 14
6202-55-0 P11 1 P9 18 P35 10 P5 12
6202-56-0 P11 7 62-255 P15 8 62-797 P37 9 P7 32
6202-83-0 P44 A P17 12 62-798 P37 10 P72 13
6202-84-0 P44 8 62-269 P5 9 62-851 P29 13 P9 22
6202-86-0 P11 19 62-295 P28 12 63-100 P1 16 63-118 P21 21
6203-27-0B P19 29 62-301 P16 20 P44 3 P23 16
P3 14 P17 13 P82 21 P27 16
6205-27-0 P19 29 62-311 P29 28 P83 7 63-119 P15 10
6206-27-0 P19 29 62-317 P34 11 P84 7 P17 18
6209-87-0 P27 10 P35 12 63-102 P1 11 63-120 P33 6
6210-42-0 P25 21 P37 6 P11 30 P33 17
62-108 P57 26 62-318 P33 19 P47 10 63-124 P13 3
6210-80-0 P33 24 62-324 P41 12 P7 38 P16 31
6210-81-0 P33 24 P43 11 P9 31 63-126 P19 10
62-115 P47 14 62-330 P2 24 63-103 P37 11 P23 24
62-167 P37 5 62-339 P21 17 P44 18 P25 5
62-169 P7 15 P7 26 63-104 P34 15 63-128 P11 3
62-176 P16 6 62-343 P49 24 P35 16 P33 33
P17 9 62-351 P35 8 P37 12 P7 2
62-191 P16 13 62-356 P47 8 63-106 P1 5 P9 3
P17 10 6236-75-0 P55 47 P33 29 63-129 P15 11
62-195 P11 10 62-385 P44 6 P34 9 P17 19
P72 16 62-387 P37 7 P35 7 63-134 P33 11
P9 14 62-394 P45 6 P49 28 P44 25
62-197 P13 17 62-414 P82 18 P82 13 P45 16
P15 6 62-417 P82 19 63-107 P37 13 P70 4
62-201 P13 19 62-420 P1 6 63-108 P16 24 63-135 P45 7
P15 7 62-421 P11 24 P17 15 P82 9
P21 13 P19 13 63-109 P19 24 63-143 P45 8
P21 24 P2 17 P2 16 6318-18-0 P19 1
62-203 P2 18 P2 17 P21 19 6318-20-0 P19 1
P23 18 P21 3 P25 20 63-204 P28 16
P25 14 P23 30 P33 15 P29 15
P40 1 P25 11 P37 14 63-208 P29 16
62-205 P21 25 P27 17 P39 8 63-230 P70 6
P23 6 P3 4 P45 5 63-231 P29 17
P27 2 P5 14 P7 18 63-234 P70 7
P28 26 P57 27 P70 16 63-235 P70 18
P28 27 62-433 P19 21 63-110 P16 9 63-236 P72 17
P38 5 62-436 P45 15 P17 16 6324-30-0 P16 1
P39 5 62-439 P2 23 P34 7
P40 14 62-458 P34 4 P35 11
Index - 4

6327-0-3 P38 11 64-100 P1 15 64-113 cont'd. P3 7 7300-86-1 P44 19
P39 11 P44 4 P38 9 7300-87-0 P44 9
P43 16 P82 20 P40 2 73-100 P13 27
6327-0-4 P39 10 P83 6 P7 40 P16 21
6327-0-5 P39 7 P84 6 P72 11 74-102 P80 5
6327-0-6 P82 17 64-101 P1 14 64-118 P11 21 P81 5
6327-0-7 P82 16 P83 5 P16 16 74-109 P30 5
6327-12-0 P21 1 P84 5 P17 22 P30 10
P21 23 64-103 P1 10 P21 11 P80 17
6327-13-0 P21 1 P47 9 P23 13 P81 17
P21 23 P57 21 P27 13 74-110 P80 22
6327-36-0 P5 6 64-104 P44 26 P5 11 P81 22
6327-87-0 P11 23 64-105 P34 14 P7 31 74-113 P61 18
P21 9 P35 15 P72 14 P62 25
P7 33 P37 15 P9 21 P63 25
P9 26 64-106 P34 13 64-119 P11 25 P64 24
63-311 P57 22 P35 14 P15 13 P65 20
6331-35-0 P19 18 P37 16 P17 23 P66 20
6331-86-0 P21 6 64-107 P1 4 P5 10 P67 19
P7 29 P33 28 P9 20 P68 7
6336-12-0 P23 3 P34 8 64-120 P28 15 74-121 P80 1
6336-13-0 P23 3 P35 6 P29 19 P81 1
6336-18-0A P23 2 P49 29 64-126 P38 15 74-151 P80 20
6336-20-0A P23 2 P82 12 P39 15 P81 20
6336-23-0 P23 1 64-108 P1 7 P40 9 74-276 P80 4
6336-26-0 P23 1 P16 44 P42 12 P81 4
6336-35-0 P23 5 P17 20 64-129 P11 5 74-348 P80 11
P27 6 P37 17 P7 3 P81 11
6337-0-3 P40 16 P82 11 P9 4 74-387 P11 31
6337-0-4 P40 5 64-109 P19 23 64-141 P33 16 P7 39
6337-42-0 P23 31 P2 15 64-148 P82 8 P80 18
6337-44-0 P23 32 P21 18 64-155 P33 2 P81 18
P25 16 P25 19 64-162 P44 11 P9 32
P3 15 P33 14 64-167 P29 20 74-391 P70 19
6337-50-0A P40 6 P37 18 64-215 P16 19 P80 6
P41 14 P39 9 P17 24 P81 6
6337-87-0 P23 15 P45 4 65-100 P19 14 74-393 P80 3
6345-0-2 P57 31 P7 17 P23 25 P81 3
6345-0-4 P40 18 P70 15 P25 10 74-487 P1 12
P41 17 64-110 P19 25 P3 8 74-489 P44 14
P42 13 P2 14 P5 19 74-515 P64 22
P43 18 P33 32 65-101 P11 13 74-516 P63 23
6345-0-6 P45 2 64-112 P11 17 P13 4 74-517 P62 23
6345-0-7 P1 2 P16 12 P15 14 74-570 P80 2
6345-0-8 P82 4 P17 21 P16 32 P81 2
6345-0-9 P82 5 P19 3 P17 25 74-571 P80 13
6345-12-0 P27 1 P2 20 P19 15 P81 13
6345-13-0 P27 8 P21 4 P23 21 74-572 P80 14
6345-18-0 P25 2 P23 8 P25 9 P81 14
6345-19-0 P25 3 P25 12 P3 9 74-574 P80 15
6345-20-0 P25 2 P27 4 P33 9 P81 15
6345-21-0 P25 3 P28 23 P5 20 74-575 P80 10
6345-23-0 P25 1 P28 28 P7 11 P81 10
6345-26-0 P25 1 P29 18 P9 11 74-576 P80 12
6345-30-0A P17 48 P3 6 65-102 P11 18 P81 12
6345-56-0 P42 4 P33 21 P9 19 74-577 P80 9
P43 14 P38 2 65-103 P7 12 P81 9
6345-58-0 P27 9 P39 2 65-107 P28 5 74-602 P80 7
6345-70-0 P33 24 P40 3 P29 21 P81 7
6345-72-0 P25 17 P42 8 65-110 P21 22 74-604 P80 16
6345-78-0 P29 A P5 17 P7 21 P81 16
6345-79-0 P29 A P57 25 65-117 P29 22 74-608 P80 21
6345-80-0 P33 24 P7 23 65-122 P28 11 P81 21
6345-81-0 P33 24 P70 12 P29 23 74-648 P80 19
6345-84-0 P25 24 P72 2 72-351 P13 22 P81 19
6345-86-0 P43 3 P9 15 72-352 P13 22 74-674 P80 23
6345-88-0 P40 13 64-113 P13 28 P15 15 P81 23
P42 2 P15 12 P16 14 74-675 P80 24
6345-89-0 P40 17 P19 6 72-356 P15 15 P81 24
P42 3 P2 19 P17 27 76-102 P44 12
P21 14 7300-75-0A P13 24 76-132 P33 4
P21 14 7300-83-3 P44 5 76-164 P11 6
P23 7 7300-83-5 P44 2 P7 4
P27 3 7300-84-0 P44 7 P9 5
Index - 5

76-201 P69 12
76-231 P16 18
P17 28
79-397 P82 22
79-401 P83 1
P84 1
79-475 P83 3
P84 3
79-476 P83 2
P84 2
79-477 P83 8
P84 8
79-546 P82 2
79-549 P82 3
79-552 P82 7
79-558 P82 1
79-577 P82 14
79-578 P82 15
950-20-4 P33 31
960-35-2 P41 15
99-215 P44 13
99-218 P2 29
P3 10
P5 16
99-243 P16 25
99-243 P17 29
Index - 6

Kuhn 6200 landsman

Recommandé

Recommandé

Contenu connexe

Tendances

Tendances (20)

Similaire à Kuhn 6200 landsman

Similaire à Kuhn 6200 landsman (20)

Plus de PartCatalogs Net

Plus de PartCatalogs Net (20)

Dernier

Dernier (20)

Kuhn 6200 landsman