Sonifex Product Update Sept10

Manufacturers of Audio & Video
Products For Radio & TV Broadcasters

New Products
Update
Sept 2010

w w w.sonifex.co.uk
t: +44 (0)1933 650 700
f: +44 (0)1933 650 726
sales@sonifex.co.uk

AUDIO & VIDEO INTERFACES

Redbox - Audio Distribution Amplifiers

RB-DA6R 6 Way Stereo Distribution Amplifier With RJ45 Connectors
AUDIO DISTRIBUTION AMPLIFIERS

The RB-DA6R is a 1U rack-mount high
performance 6 way stereo distribution
amplifier for splitting a source into a number
balanced and can be wired unbalanced.
of different outputs. The amplifier provides
Each output is individually buffered so that a
multiple balanced audio outputs using
short circuit on one output won’t affect the Distortion: 0.01% THD @ 1kHz, ref +8dBu output
RJ45 connectors wired to the StudioHub+TM Noise: -100dB unity gain, ref +8dBu output
others. The left and right input gain controls
standard *.
(normalising) are pre-set potentiometers Connections
By using RJ45 outputs, it allows simpler accessible through the front panel. Inputs: 2 x XLR 3 pin female, 1 x RJ45 socket
balanced)
CAT5 cabling to used to connect the 2 x phono sockets (unbalanced)
The output gain may be varied from -8dB
amplifier to other products. Outputs: 6 x RJ45 sockets
to 18dB which is useful for normalising (all balanced, can be unbalanced)
The RB-DA6R has one stereo input which consumer and professional signals to give Mains Input: Filtered IEC, switchable 110-120V, or
is switchable via a rear panel push switch outputs of -15dBu and 0dBu respectively. 220-240V, fused, 6W max
between paralleled balanced inputs (2 x Fuse Rating: Anti-surge fuse 100mA 20 x 5mm (230VAC)
Audio Specification For RB-DA6R Anti-surge fuse 250mA 20 x 5mm (115VAC)
XLR sockets or 1 x stereo input on RJ45) and Equipment Type
Maximum +28dBu
unbalanced inputs (1 pair of stereo phono Input Level: RB-DA6R: 6 way stereo distribution amplifier with
sockets). Maximum +28dBu RJ45 connectors
Output Level:
The unit has 6 stereo outputs on 6 x RJ45 Physical Specification
Frequency 20Hz to 20kHz ±0.1dB (600Ω load,
Dimensions 48cm (W) x 10.8cm (D) x 4.2cm (H) (1U)
connectors. The unit can also be configured Response: ref 1kHz)
(Raw): 19” (W) x 4.3” (D) x 1.7” (H) (1U)
so that 1 mono input can be distributed Gain Range: Adjustable 8dB loss to 18dB gain
(L & R adjust) Dimensions 53cm (W) x 20.5cm (D) x 6cm (H)
to 12 outputs by use of a switch which is (Boxed): 21” (W) x 8” (D) x 2.4” (H)
Common >66dB typically
Weight: Nett: 1.3kg Gross: 1.9kg
recessed on the front panel to prevent it Mode Rejection:
Nett: 2.9lbs Gross: 4.2lbs
being accidentally knocked. Input impedance: >20kΩ bridging (balanced)
>10kΩ (unbalanced) Accessories
The inputs and outputs are electronically Output impedance: <50Ω RB-RK3: 1U Rear panel rack kit for large Redboxes

RB-DA6RG 6 Way Stereo Distribution Amplifier With RJ45 Connectors & Output Gain Control

The RB-DA6RG is a 1U rack-mount high to the RB-DA6R with the addition of
Audio Specification For RB-DA6RG
performance 6 way stereo distribution individual output gain adjustment, instead
As per RB-DA6R with the following difference:
amplifier for splitting a source into a of global stereo gain adjustment. Gain Range: Adjustable 8dB loss to 18dB gain
number of different outputs. It is identical (12 adjustable pots)

* StudioHub+TM is a registered trademark of Radio Systems Inc

2 Tel: +44 (0)1933 650 700 Fax: +44 (0)1933 650 726 Email: sales@sonifex.co.uk Internet: www.sonifex.co.uk


Redbox - Audio Distribution Amplifiers

RB-DDA22 Digital Audio Distribution Amplifier With Multiple Outputs

192

AUDIO DISTRIBUTION AMPLIFIERS
“
The RB-DDA22 is a multiple input and Note: The BNC outputs can be converted
When an input is selected, multiple output digital audio distribution to S/PDIF outputs using a simple locking
it is copied to all of the available amplifier designed to accept one of 5 connector, available separately, giving an
outputs. There are 5 sets of digital different digital inputs, amplify it and output additional 6 x S/PDIF outputs, if required.
“
audio outputs, providing 22 outputs this to 22 digital audio outputs in 5 different
audio formats. Technical Specification For RB-DDA22
in total. Audio Specification
Input & Output 110Ω ±20% AES/EBU balanced I/O
It accepts signals with sample rates in the Impedances: 75Ω ±5% S/PDIF unbalanced I/O
range 32kHz to 192kHz and distributes them 75Ω ±5% TOSlink unbalanced I/O
Signal Level: Balanced: 3V/10V peak to peak
without sample rate conversion. min/max
Unbalanced: Min 0.5V±20% peak
There are 5 inputs, one each of balanced to peak
Sample 32, 44.1, 48, 88.2, 96,176.4 or 192kHz
AES/EBU on an XLR socket, unbalanced Frequencies:
AES/EBU on BNC, balanced AES/EBU on an Bit Depth: Up to and including 24 bit
RJ45 socket, unbalanced S/PDIF on a phono Front Panel Operational Controls & Indicators
socket and a TOSlink optical connection. Digital AES/EBU (XLR), AES/EBU (BNC), AES/EBU
Input Select: (RJ45), S/PDIF or TOSlink optical
An illuminated front panel input select push Indicators: Input presence indicators via tricolour
LEDS around the input select button
button is used to choose one of the 5 inputs,
Connections
or to select the Auto Mode. In Auto Mode Digital Inputs: 1 x AES/EBU XLR 3 pin socket
the unit interrogates each of the inputs in 1 x AES/EBU BNC
1 x AES/EBU RJ45 socket (StudioHub+TM)
turn until it finds a lock. The select button 1 x S/PDIF RCA phono socket
1 x TOSLink optical input
flashes to indicate loss of lock and the tri-
Digital Outputs: 6 x AES/EBU XLR 3 pin plug
colour input LEDs around the push button 6 x AES/EBU BNC
6 x AES/EBU RJ45 socket (StudioHub+TM)
indicate signal presence. 2 x S/PDIF RCA phono socket
2 x TOSLink optical output
When an input is selected, it is copied to Mains Input: Universal filtered IEC, continuously
rated 85-264VAC@47- 63Hz, max 10W
all of the available outputs. There are 5
Fuse Rating: Anti-surge fuse 1A 20 x 5mm
sets of digital audio outputs consisting of:
Equipment Type
6 x balanced AES/EBU on XLR plugs, 6 x RB-DDA22: Digital audio distribution amplifier with
professional unbalanced AES/EBU on BNCs, multiple outputs
6 x balanced AES/EBU on RJ45 sockets, 2 x Physical Specification
unbalanced S/PDIF on phono sockets and 2 Dimensions 48cm (W) x 10.8cm (D) x 4.2cm (H) (1U)
(Raw): 19” (W) x 4.3” (D) x 1.7” (H) (1U)
x TOSlink optical outputs, giving 22 outputs Dimensions 53cm (W) x 20.5cm (D) x 6cm (H)
(Boxed): 21” (W) x 8” (D) x 2.4” (H)
in total, 12 balanced and 10 unbalanced.
Nett: 3.0lbs Gross: 4.4lbs
The RJ45 input and output connections use
Accessories
the StudioHub+TM * wiring standard for the
RB-RK3: 1U Rear panel rack kit for large
balanced AES/EBU connections. Redboxes

* StudioHub+TM is a registered trademark of Radio Systems Inc

Tel: +44 (0)1933 650 700 Fax: +44 (0)1933 650 726 Email: sales@sonifex.co.uk Internet: www.sonifex.co.uk 3


Redbox - Synchronisers, Delays & Silence Detectors

RB-DSD8 8 Channel Silence Switcher
SYNCHRONISERS, DELAYS & SILENCE DETECTORS

The RB-DSD8 8 channel silence switcher status of the digital audio on that channel durations, levels and switching functions so
works in a similar way to the Sonifex and a Selection LED to show that input is that you can set up the unit for your specific
RB-SD1 and RB-DSD1 but allows for 4 currently being sent to each respective application. A DIPSwitch configures the unit
stereo channels of audio. These stereo output. Two Presence LEDS for the left and to be controlled serially which is indicated
audio channels can be either analogue or right inputs of each stereo pair indicate the by a front panel LED. You can control the
digital and can be used independently to input level of the channels. unit remotely using either USB or Ethernet.
give 4 stereo silence detectors or they can
The unit can switch between sources The RB-DSD8 has been designed with dual
be linked to handle multichannel audio
manually or automatically at the push of redundant power supplies. This means
inputs, e.g. for 5.1 and 7.1 surround systems.
a button. If switching manually, silence that if either power supply fails, the other
Designed to switch from one input (or set
detection is disabled and the user chooses is ready to take over. In the extremely
of inputs) to another in the event of loss of
when to switch using the main or backup unlikely event that both fail, the unit has
audio, the unit is ideal at transmitter sites, or
buttons. If switching automatically, the been designed with a passive signal path
after the master output of a studio, to switch
unit switches between the two sources through the main input. This is essential
in another audio source, or simultaneous
automatically upon the detection of for applications such as installation at
broadcast, should a master source fail.
silence. Each pair can be set to switch transmitter sites, where a power failure to
The unit can switch: manually or automatically and the current the unit should not prevent the audio input
• On loss of level of the main input. setting is indicated by the Mode LED. Link/ signal from being output to the transmitter.
• On loss of level on one channel of the Select buttons are used to group channels
main input. Contact Sonifex for further information if
together to access multichannel operation
• On loss of synchronisation lock of a main you have a particular requirement that isn’t
and switch simultaneously. Each pair has a
digital input. catered for by the RB-DSD8 as standard.
Link/Select button which illuminates blue
The 2 x 8 channel audio inputs can accept when active. Pressing and holding the first Clocking & Synchronisation
both digital and analogue connections, Link/Select button with any other Link/ All digital input signals are routed to a
with the unit automatically recognising a Select button causes all inputs up to that sample rate converter allowing mixed
digital input. For the 8 channel outputs, by point to be selected. incoming sample rates to be used. The
setting the appropriate DIPSwitches, each output sample rates are selectable from a
The RB-DSD8 has a ‘slave mode’ that allows
stereo output can be designated as either predefined master clock of 32kHz, 44.1kHz,
you to connect two RB-DSD8 units and
an analogue pair or as a digital output, thus 48kHz, 88.2kHz, 96kHz, 176.4kHz or 192kHz
control them simultaneously from one unit.
making the RB-DSD8 incredibly flexible and or the clock can be derived from a sync
suitable for many different applications. The silence detect level is adjustable input. When analogue inputs are selected,
The unit level settings are in dBFS but when between -39dBFS and -84dBFS in 3dBFS the analogue to digital converters are also
using analogue signals the equivalent full steps via DIPSwitches and this level is clocked at that sample rate.
scale value can be set to +24dBu, +18dBu, or compared to peak signals. The silence
DIPSwitches choose the synchronisation
+12dBu by DIPSwitches. interval can be adjusted between 2 seconds
mode and the sync source from TTL
and 254 seconds in 2 second steps via
Each stereo pair has individual settings and wordclock or AES/EBU through the dual-
DIPSwitches.
controls and when stereo signals are linked, purpose synchronising input as standard.
the foremost pair determines the switching A powerful feature of the RB-DSD8 is that A front panel indicator shows the status of
characteristics and controls to be used. Each by using the Sonifex SCi serial software, the the synchronization input. Selectable sync
stereo pair has an AES LED that shows the unit can be programmed for different delay modes are as follows:



Redbox - Synchronisers, Delays & Silence Detectors
Master Mode Audio Specification - Analogue Remote Control Enabled or disabled, via rear panel
Maximum Input +24dBu Enable: DIPswitch
In this mode the digital output sample rate Level: Sync Mode & Sync in master mode or sync from
is simply set by, and locked to, the internal Input Impedance: >20kΩ bridging balanced Source Select: MAIN input1, AES or wordclock
sync input in auto or slave mode, via
on-board clock generator. No sync signal is Dynamic Range: >110dB rear panel DIPswitches
Distortion & Noise: >82dB THD + N at 1kHz
used or required. Remote Start: Latched or momentary, via
Common Mode >60dB , ref 0dBu DIPswitch
Rejection: Input Lock Loss: Switch immediately or treat as
Auto Lock Mode

SYNCHRONISERS, DELAYS & SILENCE DETECTORS
silence delay, via rear panel
Front Panel Operational Controls
In this mode no output is generated until DIPswitch
Switch Mode Select: Via AUTO, MANUAL or SLAVE
Digital or Digital or analogue, via rear panel
lock is achieved with a sync signal. The push-buttons
Analogue Output: DIPswitches
Manual Source Via MAIN and BACKUP
digital output sample rate now follows the Select: push-buttons
Full Scale Line Up: 24, 18 or 12 dBu = 0dBFS, via rear
panel DIPswitches
sync input. If the sync signal is removed Group Selection : Via LINK/SELECT push-buttons
Boot Mode: Boot in boot or normal via rear
then the output sample rate is set by, and Front Panel Indicators panel DIPswitch
Presence LEDs: For all input channels Connections
locked to, the internal on-board clock
Link LEDs: Show which channels are Digital/Analogue 2 x 8 channel inputs on
generator at the closest frequency available controlled concurrently Inputs: 2 x 25 pin D-type male
to the previous sync input. Mode LEDs: Indicate the current mode selected Digital/Analogue 1 x 8 channel outputs on
for each group Outputs: 1 x 25 pin D-type female
Selection LEDs: Indicate whether MAIN or BACKUP Sync Inputs: 1 x BNC (Wordclock or AES)
Slave Mode is selected Remote I/O Port: 25 way D-type female
Here the digital output sample rate follows AES LEDs: Show the state of the digital input to SCi port: USB or ethernet
each group
the sync input. When the sync signal is not Mains Input: 2 x Universal filtered IEC,
PSU LEDs: Show the state of each power continuously rated 85-264VAC
present the digital output is turned off. supply @47- 63Hz, max 60W
Remote Control LED: Show if remote control is selected Fuse Rating: 2 X Anti-surge fuse 2A 20 x 5mm
External Sync LED: Show the state of any sync inputs
used. Equipment Type
Audio Specification For RB-DSD8 RB-DSD8: 8 channel silence switcher
Rear Panel - Operational Controls
Audio Specification - Digital Silence Threshold: -39dBfs to -84dBfs in 3dBfs Physical Specifications
Dynamic Range: >138dB steps, via rear panel DIPSwitches Dimensions 48cm(W) x 22cm(D) x 4.2cm(H) 1U
Distortion & Noise: <-137dB THD + N at 1kHz, Silence Duration: 0 - 254 seconds in 2 second (Raw): 19” (W) x 8.7” (D) x 1.7” (H) 1U
ref 0dBFS intervals duration, via rear panel Weight: Nett: 2.3kg Gross: 2.9kg
DIPSwitches Nett: 5.1lb Gross: 6.4lb
Input & Output 110Ω ± 20% AES/EBU balanced
Impedances: I/O 50Ω BNC TTL word clock input Stereo/Mono Stereo or mono, via rear panel * Note that this product is deeper than standard
Switching: DIPSwitch Redboxes
Signal Level: Balanced: 3V/10V peak to peak
min/max Master Select: 32, 44.1, 48, 88.2, 96,176.4 or 192kHz
Output sample rate, via rear panel Accessories
Sample Rates: 32, 44.1, 48, 88.2, 96,176.4 or DIPSwitches RB-RK3: 1U Rear panel rack kit for large
192kHz Redboxes
Ignore Silence: Each channel can be set to ignore
Bit Depth: Up to and including 24 bit silences, via rear panel DIPswitches

RB-DEED8 Dolby® E Encoder 8 Channel, Digital Inputs

Dolby® and the double-D symbol are registered trademarks of Dolby Laboratories

The RB-DEED8 is a Dolby® E Encoder. It either BNC or D-type connectors. These I/O between NTSC, PAL or Tri-level sync.
encodes up to 8 digital audio channels into connections are paralleled, allowing one
8 general purposes inputs and 8 outputs
a single Dolby bitstream output. There is type to be used per input or output.
are available on a rear panel 25 way D-type
also an extra Dolby output for connection to
Metadata can be input to the encoder using socket whose function can be programmed
monitoring equipment.
RS-485 via the external 9-pin D-type socket using the menu, e.g. alarm outputs for loss
Each digital input channel has independent on the rear panel and can also be viewed of input or encoder errors.
level control, which can be adjusted from using the SCi software.
The unit is controlled locally using the front
-24dB through to +24dB in 0.5dB steps. The
A video input is used to genlock the audio panel display and control knob but can
digital inputs and outputs can be selected to
output and Dolby® E encoding to a known be remote controlled via an RS-232 serial
be either balanced or unbalanced AES/EBU
video reference. This input autodetects connection using the Sonifex SCi software.
specification, and can be connected through



Redbox - Dolby® Encoders & Decoders

RB-DEED8 Dolby® E Encoder 8 Channel, Digital Inputs (continued...)

Audio Specification For RB-DEED8 Video Reference Physical Specifications
Output Sample 48kHz Reference Type: Autodetect NTSC, PAL or Tri-level Dimensions 48cm (W) x 10.8cm (D*)x 4.2cm (H)
Rate: sync (Raw): 19” (W) x 4.3” (D*) x 1.7” (H) (1U)
Input Sample Rates: CH1/2 & CH3/4: 32-192kHz Impedance: 75Ω Dimensions 59cm (W) x 27.5cm (D) x 11cm (H)
CH5/6 & CH7/8: 32-48kHz Connector: 1 x BNC (Boxed): 23.2” (W) x 10.8” (D) x 4.3” (H)
DOLBY® ENCODERS & DECODERS

Input & Output 75Ω/110Ω selectable LTC Input: 1 x BNC (not used) Weight: Nett: 1.8kg Gross: 2.3kg
Impedance: Nett: 4.0lb Gross: 5.1lb
Operational Control
Signal Level Unbalanced: 1Vp-p +/- 20% * Note that this product is deeper than standard
(un-terminated): Balanced: 6.6Vp-p +/- 20% Display: Vacuum fluorescent display
Redboxes
Digital Audio I/O: System Navigation: Rotary selector with integral push-
Inputs: 8 input channels via 4 x BNCs or switch Equipment Type
25 way D-type socket (AES3) Additional Connections RB-DEED8 Dolby® E encoder 8 channel, digital
Dolby Output 1: 1 x Dolby bitstream output via BNC Remote 25-way ‘D’-type socket inputs
Dolby Output 2: 1 x Dolby bitstream output via BNC Input/Output Port: Accessories
or 25 way D-type socket (AES3) Serial Port: RS232, 9 way D-type RB-RK3: 1U Rear panel rack kit for large
Digital Audio 6 x BNC Power Supply: Universal filtered IEC, continuously Redboxes
Connectors: 1 x 25-way D-type socket rated 85-264VAC @47-63Hz, fused
Metadata: SMPTE-RDD06, 9 way D-type socket Fuse Rating: Anti-surge fuse 1A 20 x 5mm

RB-DEDD8 Dolby® E & Dolby Digital Decoder 8 Channel, Digital Outputs

The RB-DEDD8 is a Dolby® E & Dolby Digital 8 general purposes inputs and 8 outputs Video Reference
Decoder. It decodes an incoming Dolby are available on a rear panel 25 way D-type Reference Type: Autodetect NTSC, PAL or Tri-level
sync
bitstream and transmits the decoded socket whose function can be programmed Impedance: 75Ω
outputs on BNC or D-type connectors on the using the menu, e.g. alarm outputs for loss Connector: 1 x BNC
rear panel. The Dolby input is also looped of input or decoder errors. LTC Output: 1 x BNC (not used)
through to allow connection to other Dolby Operational Control
The unit is controlled locally through the
receiver equipment. Display: Vacuum fluorescent display
front panel display but can be remote System Navigation: Rotary selector with integral push-
Each digital output channel has independent controlled via an RS-232 serial connection switch
level control, which can be adjusted from using the Sonifex SCi software. Additional Connections
Remote 25-way ‘D’-type socket
-24dB through to +24dB in 0.5dB steps. The Input/Output Port:
digital inputs and outputs can be selected to Serial Port: RS232, 9 way D-type socket
Audio Specification For RB-DEDD8
be either balanced or unbalanced AES/EBU Power Supply: Universal filtered IEC, continuously
Output Sample 48kHz rated 85-264VAC @47-63Hz, fused
specification, and can be connected through Rate:
Fuse Rating: Anti-surge fuse 1A 20 x 5mm
either BNC or D-type connectors. These I/O Input Sample Rates: 32-48kHz
Physical Specifications
connections are paralleled, allowing one type Input & Output 75Ω/110Ω selectable
Dimensions 48cm (W) x 10.8cm (D*)x 4.2cm (H)
Impedance:
to be used per input or output. Signal Level Unbalanced: 1Vp-p ±20%
(Raw): 19” (W) x 4.3” (D*) x 1.7” (H) (1U)
(Un-terminated): Balanced: 6.6Vp-p ±20% Dimensions 59cm (W) x 27.5cm (D) x 11cm (H)
The metadata output from the decoder is Digital Audio I/O:
(Boxed): 23.2” (W) x 10.8” (D) x 4.3” (H)
transmitted using RS-485 via the external Dolby Input: 1 x Dolby bitstream input via BNC Weight: Nett: 1.8kg Gross: 2.3kg
Nett: 4.0lb Gross: 5.1lb
9-pin D-type socket on the rear panel and can Outputs: 8 x Digital audio output channels &
2 x Auxiliary audio output (stereo * Note that this product is deeper than standard
also be viewed using the SCi software. downmix) channels via 5 x BNCs or Redboxes
25 way D-type socket
Equipment Type
A video input is used to genlock the audio Dolby Output: 1 x Dolby bitstream output via BNC
RB-DEDD8 Dolby® E & Dolby Digital decoder 8
or D-type
outputs and Dolby® E decoding to a known channel, digital outputs
Digital Audio 7 x BNC
video reference. This input autodetects Connectors: 1 x 25 way D-type socket Accessories
between NTSC, PAL or Tri-level sync. Metadata: SMPTE-RDD06, 9 way D-type socket RB-RK3: 1U Rear panel rack kit for large
Redboxes
Dolby® and the double-D symbol are registered trademarks of Dolby Laboratories



Redbox - Video Embedders & De-embedders

RB-VHEDD8 3G/HD/SD-SDI Dolby® E Encoder & Embedder

The RB-VHEDD8 is a Dolby® E Encoder
and Embedder. It
encodes 8 channels

VIDEO EMBEDDERS & DE-EMBEDDERS
of audio into two
channels of an
AES/EBU digital
audio stream which is
then embedded onto
any of the available
groups within each of the
two video output paths. It is also
transmitted on a BNC or D-type on the
rear panel.

The audio inputs to the encoder can be Audio Specification For RB-VHEDD8 Signal Level Unbalanced: 1Vp-p ±20%
(Un-terminated): Balanced: 6.6Vp-p ±20%
selected to either come from the external SDI Specification
SDI Input: 1 x BNC, 3G/HD/SD-SDI Digital Audio I/O:
audio inputs via the BNC or D-type Inputs: 8 x digital audio input channels via
SDI Outputs: 2 x BNC, 3G/HD/SD-SDI, re-clocked 4 x BNCs or 25 way D-type socket
connections on the rear panel or from the Impedance: 75Ω (AES3)
audio in the incoming SDI input. Similarly, Output Alignment <0.2UI (3G <0.3UI) Outputs: 2 output channels via 1 x BNC
Jitter: or 25 way D-type socket (AES3)
the metadata input for the encoder can be Digital Audio 5 x BNC
Output Level: 800mV ±10%
selected to either come via the external Return Loss: <15dB at 1500MHz Connectors: 1 x 25-way D-type socket
9-pin D-type on the rear panel or from SDI Supported 270Mbps, SMPTE-259M-C (SD) LTC Input: 1 x BNC (not used)
Standards: 1.485 or 1.4835Gbps, SMPTE-292M Operational Control
metadata embedded into the vertical (HD) Display: Vacuum fluorescent display
blanking area of the video input. 2.97 or 2.967Gbps, SMPTE-424M
(3G), SMPTE-425M-A System Navigation: Rotary selector with integral push-
switch
Supported Video 525/59.94 (SMPTE-125M)
The unit is controlled locally through the Formats: 625/50 (ITU-R BT.656) Additional Conections
front panel display but can be remote 720p/23.98, 24, 25, 29.97, 30, 50, Ethernet Port: 10/100Mbps, RJ-45
59.94, 60 (SMPTE-296M) Remote 25-way ‘D’-type socket
controlled via an ethernet connection using 1035i/59.94, 60 (SMPTE-260M) Input/Output Port:
1080i/50, 59.94, 60 (SMPTE-274M)
the Sonifex SCi software. The embedding 1080p/23.98, 24, 25, 50, 59.94, 60 Power Supply: Universal filtered IEC, continuously
(SMPTE-274M) rated 85-264VAC @47-63Hz, fused
channel routing is controlled using these 1080pSF/23.98, 24, 25, 29.97, 30 Fuse Rating: Anti-surge fuse 1A 20 x 5mm
methods also. (RP-211)
Physical Specifications
1080i/50 (SMPTE-295M)
1080p/50 (SMPTE-295M) Dimensions 48cm (W) x 10.8cm (D*)x 4.2cm (H)
It has a triple rate SDI receiver with (Raw): 19” (W) x 4.3” (D*) x 1.7” (H) (1U)
Embedded Audio: 24-bit, 48kHz synchronous
automatic input rate detection and SMPTE-272M-C Dimensions 59cm (W) x 27.5cm (D) x 11cm (H)
SMPTE-299M (Boxed): 23.2” (W) x 10.8” (D) x 4.3” (H)
equalisation along with two re-clocked and Metadata: SMPTE-2020M
Nett: 4.0lb Gross: 5.1lb
individually buffered SDI outputs. It supports SMPTE-RDD06, 9-Pin D-type socket
* Note that this product is deeper than standard
the full range of 3G, HD and SD standards Audio Specifications Redboxes
from NTSC and PAL up to 1080p 60Hz. Output Sample 48kHz Equipment Type
Rate: RB-VHEDD8 3G/HD/SD-SDI Dolby® E encoder &
Input Sample Rates: CH1/2 & CH3/4: 32-192kHz embedder
Each digital input channel has independent CH5/6 & CH7/8: 32-48kHz Accessories
level control, which can be adjusted from Input & Output 75Ω/110Ω selectable RB-RK3: 1U Rear panel rack kit for large
Impedance:
-24dB through to +24dB in 0.5dB steps. The Redboxes

digital inputs and outputs can be selected to
be either balanced or unbalanced AES/EBU Metadata Metadata Audio Audio SDI SDI
Input VANC Pass / Embedder Transmitter Output 1
specification, and can be connected through De-embedder Delete
CD
either BNC or D-type connectors. These I/O
connections are paralleled, allowing one
SDI Audio SDI
type to be used per input or output. Input
SDI
Receiver
Audio
De-embedder
Pass / Audio
Embedder
SDI
Transmitter Output 2
Delete
EQ CD
8 general purposes inputs and 8 outputs
are available on a rear panel 25 way D-type 8
socket whose function can be programmed
Digital AES RX/TX Dolby E
using the menu, e.g. alarm outputs for loss of Audio and
Channel
Routing Encoder
input or encoder errors. I/O Termination & Level
Select Control
2
8

RB-VHEDD8 Block Diagram



Redbox - Video Embedders & De-embedders

RB-VHDDD8 3G/HD/SD-SDI Dolby® E & Dolby Digital Decoder & De-Embedder

The RB-VHDDD8 is a Dolby® E & Dolby
Digital Decoder and De-Embedder. It
de-embeds up to 10 channels of audio
VIDEO EMBEDDERS & DE-EMBEDDERS

within any audio group of an SDI video
signal and a further 2 which are sent to
the Dolby® Decoder. The outputs from the
Decoder or the De-embedder can then be
re-embedded onto either of the two SDI
outputs and also transmitted on a BNC or
D-type situated on the rear panel.

The metadata output from the decoder is
transmitted using RS-485 via the external Audio Specification For RB-VHDDD8 Output Impedance: 75Ω/110Ω selectable
SDI Specification Signal Level Unbalanced: 1Vp-p +/- 20%
9-pin D-type on the rear panel and can also (Un-terminated): Balanced: 6.4Vp-p +/- 20%
SDI Input: 1 x BNC, 3G/HD/SD-SDI
be embedded into the vertical blanking SDI Outputs: 2 x BNC, 3G/HD/SD-SDI, re-clocked
Digital Audio 12 output channels via 6 x BNC or
Outputs: 25 way D-type socket (AES3)
space onto either of the two SDI outputs. Impedance: 75Ω Digital Audio 6 x BNC
Output Alignment <0.2UI (3G <0.3UI) Connectors: 1x 25-way D-type socket
The unit is controlled locally through the Jitter:
Output Level: 800mV ±10% Operational Control
front panel display but can be remote Display: Vacuum fluorescent display
Return Loss: <15dB at 1500MHz
controlled via an ethernet connection using SDI Supported 270Mbps, SMPTE-259M-C (SD) System Navigation: Rotary selector with integral push-
switch
the Sonifex SCi software, through which Standards: 1.485 or 1.4835Gbps, SMPTE-292M
(HD) Additional Conections
metadata can also be viewed. It has a triple 2.97 or 2.967Gbps, SMPTE-424M Ethernet Port: 10/100Mbps, RJ-45
(3G), SMPTE-425M-A
rate SDI receiver with automatic input rate Remote 25-way ‘D’-type socket
Supported Video 525/59.94 (SMPTE-125M) Input/Output Port:
detection and equalisation along with two Formats: 625/50 (ITU-R BT.656)
720p/23.98, 24, 25, 29.97, 30, 50, Power Supply: Universal filtered IEC, continuously
re-clocked and individually buffered SDI 59.94, 60 (SMPTE-296M) rated 85-264VAC @47-63Hz, fused
outputs. It supports the full range of 3G, HD 1035i/59.94, 60 (SMPTE-260M) Fuse Rating: Anti-surge fuse 1A 20 x 5mm
1080i/50, 59.94, 60 (SMPTE-274M) Physical Specifications
and SD standards from NTSC and PAL up to 1080p/23.98, 24, 25, 50, 59.94, 60
(SMPTE-274M) Dimensions 48cm (W) x 10.8cm (D*)x 4.2cm (H)
1080p 60Hz. 1080pSF/23.98, 24, 25, 29.97, 30 (Raw): 19” (W) x 4.3” (D*) x 1.7” (H) (1U)
(RP-211) Dimensions 59cm (W) x 27.5cm (D) x 11cm (H)
Each digital output channel has 1080i/50 (SMPTE-295M) (Boxed): 23.2” (W) x 10.8” (D) x 4.3” (H)
1080p/50 (SMPTE-295M) Weight: Nett: 1.8kg Gross: 2.3kg
independent level control which can be Embedded Audio: 24-bit, 48kHz synchronous Nett: 4.0lb Gross: 5.1lb
adjusted from -24dB through to +24dB SMPTE-272M-C * Note that this product is deeper than standard
SMPTE-299M Redboxes
in 0.5dB steps. The digital outputs can Metadata: SMPTE-2020M
SMPTE-RDD06, 9-Pin D-type Equipment Type
be selected to be either balanced or
Audio Specifications RB-VHDDD8 3G/HD/SD-SDI Dolby® E & Dolby
unbalanced AES/EBU specification, and can Digital decoder & de-embedder
Output Sample 48kHz
be connected through either BNC or D-type Rate: Accessories
connectors. These output connections are RB-RK3: 1U Rear panel rack kit for large
Redboxes
paralleled, allowing one type to be used per
RB-VHDDD8 Block Diagram
output.
8 general purposes
Audio Metadata
inputs and 8 outputs are Pass /
Audio
VANC
SDI SDI
Output 1
Embedder Transmitter
available on a rear panel Delete Embed
CD
25 way D-type socket
whose function can be
programmed using the SDI SDI Audio
Audio
Pass /
Audio
Metadata
Vanc SDI SDI
Input Receiver De-embedder Embedder Transmitter Output 2
menu, e.g. alarm outputs Delete Embed
EQ CD
for loss of input or
decoder errors. 2 10 Channel
Routing
& Level
Dolby E & Control Digital
Dolby Digital
10 AES
Audio
Transmitter
Decoder & Outputs
Termination
Select

Metadata
Output


TALKBACK & COMMUNICATIONS

Talkback & Communications

CM-TBU Line Powered Telephone Balance Unit

The CM-TBU line-powered by the ‘ON’ LED, and can either be done
after an outgoing call has been dialled on
telephone balance unit a telephone set connected to the unit, or

is compatible with all to answer an incoming call after the ‘RING’
analogue direct exchange LED is seen to flash. Note that a telephone
lines and provides a 4-wire set is not required for incoming calls unless
an audible ring is required. If the sidetone
communications system to level at the 4-wire output is found to be
interface with the telephone excessive, the outgoing signal level can
network. be reduced usingthe ‘SEND LEVEL’ control
or the balance controls can be adjusted to
The high degree of separation between minimize it.
send and receive signals makes it suitable The unit is supplied with a connector and
for use in telephone IFB (interrupted cable kit that enables connections to be
foldback) applications and the high drive made to both UK Telecom or the universal
capacity at the 4-wire output enables Front and rear view of the CM-TBU
RJ11 sockets used in most telephone
a presenter’s earpiece to be connected networks around the world.
circuit by adjusting three elements (NULL,
directly to the unit without an external
R-BAL and C-BAL) via potentiometers which
amplifier.
simulate the complex line impedance. This
This extremely compact unit is powered can be used to compensate for local line Technical Specification For CM-TBU
from the telephone line and provides an variations or to adapt to the telephone 4-Wire Input
interface to a 4-wire circuit with separate systems of other countries, where line Input Impedance: 10kΩ, transformer coupled
level control of send and receive signals. characteristics may differ. Optimization of Input Connector: 3 pin XLR female connector
the sidetone rejection does not involve the Input Level Range: -12dBU to +4dBU before
Optimum rejection of the input signal on limiting when connected to
use of any test equipment and can be easily an average line
the 4-wire output is achieved in a bridge
carried out while the system is in use. 4-Wire Output
Output Impedance: 150Ω, transformer coupled
Features of the CM-TBU Although the signal level being sent to the Output Connector: 3 pin XLR male connector
line can be manually adjusted using the Output Level Range: -6dBU to +6dBU, for average
• Isolated, full-duplex 4-wire interface
‘SEND LEVEL’ control over a wide range, the line level
to direct non-digital telephone Sidetone Rejection: 30dB to 40dB average, depending
level control is followed by a limiter that on line characteristics
exchange lines.
prevents the telephone line signal level 2-Wire
• Line powered, requiring no battery or
becoming overloaded or distorted. The Off Hook Voltage: 6V minimum
external power.
limiter drives a ‘LIMIT’ LED to indicate the 2 Wire Connectors: RJ11 socket - line
• Simple optimization of sidetone RJ11 socket - handset
onset of limiting.
rejection with any country’s Front Panel Operational Controls

telephone system. Line Connect: Push button with indicator
Although the output stage can drive a
Send Level: Small rotary control
• LEDs indicating ‘Ring’, ‘Line Hold’ and presenter’s earpiece in a telephone IFB
Receive Level: Large rotary control
‘Limit’ conditions. application, the ‘RECEIVE LEVEL’ control may Null Balance: Recessed preset potentiometer
• Input level control with line-sensing not be accessible to the presenter, who is R Balance: Recessed preset potentiometer
limiter and limit indicator. normally situated some distance from the C Balance: Recessed preset potentiometer
• High drive output with level control unit. The presenter may then require a local Ring LED: Indicates incoming ringing
for direct feed to presenter’s control of the earpiece signal level. The CM- Limit LED: Indicates limiter active

earpiece, etc. TBU can be used to supply the correct signal On LED: Indicates connection to the
telephone line
• Loop-through RJ11 line sockets level to a suitable battery powered earpiece Equipment Type
provide universal connection to line belt-pack unit. CM-TBU Line powered telephone
and telephone set. balance unit
To enable communication between the Physical Specification
• Connection to the telephone set is
4-wire circuit and the telephone network, Dimensions: 77mm (W) x 83mm (D) x
maintained while the unit is in use. 42mm (H)
once the 4-wire and telephone line cable
• Small, rugged extruded aluminium 3.0” (W) x 3.3” (D) x 1.7” (H)
connections are made to the unit, the ‘LINE Weight: Nett: 0.25kg Gross: 0.75kg
case with XLR3 male & female 4-wire
CONNECT’ switch can be pressed to power Nett: 0.60lbs Gross: 1.7lbs
connectors.
the unit from the line. This is indicated



Talkback & Communications

CM-TLL Line Powered Telephone Line Listen Unit

The CM-TLL provides a The line and telephone set are connected
to the unit via the RJ11 connectors in order Features of the CM-TLL
low-loss interface to receive
to make an outgoing call. A telephone may
TALKBACK & COMMUNICATIONS & STUDIO ILLUMINATED SIGNS

audio from a telephone line. not be required if calls are only incoming,
• Audio interface to direct analogue
exchange lines - receive calls with
The line-powered unit is because telephone line ringing is indicated electrical isolation from the line.
compatible with all analogue by a flashing LED built into the unit. In • Line powered, requiring no battery or
either case, the ‘LINE CONNECT’ switch is
direct exchange lines and pressed to make the line connection. The
external power.
• LEDs indicating ‘Ring’ and ‘On Hold’
includes an LED indication ‘ON’ LED indicates that the unit is powered conditions.
of incoming calls. The unit is and that audio is routed to the line via the • Loop-through line sockets provide
intended to be used with an XLR plug. in-line connection with existing
earpiece amplifier to receive telephone.
• Existing telephone remains
an audio feed by telephone Technical Specification For CM-TLL
4-Wire Output connected when the unit is in use.
from a studio. Output Impedance: 150Ω, transformer coupled • Line connections to British or
Output Connector: 3 pin XLR male connector
International sockets via supplied
Output Level: Typically 0dBU for average line level
cable kit.
2-Wire
Off Hook Voltage: 6V minimum
• Connection to the telephone set is
2 Wire Connectors: RJ11 socket - line maintained while the unit is in use.
RJ11 socket - handset • Small, rugged extruded aluminium
Front Panel Operational Controls case with XLR3 male 4-wire
Line Connect: Push button with indicator connector.
Ring LED: Indicates incoming ringing
On LED: Indicates connection to the
telephone line

“
Equipment Type
CM-TLL Line powered telephone line listen An audio interface to connect to
unit
Physical Specification direct analogue exchange lines and
“
Dimensions: 77mm (W) x 83mm (D) x 42mm (H) receive calls with electrical isolation
3.0” (W) x 3.3” (D) x 1.7” (H)
Weight: Nett: 0.20kg Gross: 0.70kg from the line.
Front and rear view of the CM-TLL Nett: 0.50lbs Gross: 1.6lbs

Studio Illuminated Signs

New Remote Programming Controller

New
New Remote Programming Programming
Controller Method
Changes to
The signs are preconfigured to display
certain colours when the control inputs are
active. Information on the colours shown
SignalLED signs can be found on the Sonifex website. Prior
to 1st December 2010, the display mode
Programming
Controller must be
sold after 1st and colour options could then be varied
using an 8 way DIPswitch, accessible
used. This allows a much
simpler way of programming any sign

December 2010 during installation. From 1st December
2010, this is different - the signs are still
using a simple hand-held remote control.
Please note that the control is sold
preconfigured, but to vary the colours separately and one control can program
and switching modes, the LD-RPC Remote multiple signs.


PHONE IN 6

Radio Talkshow System

Phone In 6 Radio Talkshow Telephone Switching System

PHONE IN 6
PI-6R Remote Control Front Panel

Talkshows have never been so easy Features List
• Simple installation using CAT5 cabling for the
The Phone In 6 is a telephone switching system for radio remote control panel.
talkshows. It consists of a desktop Remote Control Panel for call • Automatic call answering.
control, and a rackmount Base Console which contains all of the • Automatic call disconnection.
• Self-op or call screening modes.
audio and telephony connections, including two superb quality • Caller conferencing.
digital telephone hybrids. Connected via ethernet, the units • Headset included with system.
make up a simple, easy to use talkshow system. • Simple switch button control of callers.
• Receive, route, drop or make calls.
The Base Console can be loaded with 2, 4, or The Phone In 6 uses an echo-cancellation • 12 digit keypad to make calls, recall favourite
6 phone line modules, where each module DSP algorithm and impedance matching settings and for speed-dialling.
can have 2 PSTN (normal telephone) lines or to give around 70dB cancellation, which • Two line LCD display.
1 ISDN BRI line. The ISDN basic rate interface provides excellent separation of caller & line • Phonebook for automatic dialling.
allows 2 calls to be handled, 1 on each B send audio and elimination of feedback, • Responsive illuminated switch buttons.
channel. The PSTN module has 2 interfaces distortion & echo on the incoming calls. • Programmable GPIO.
each using a modern digital hybrid interface, This is close to being the best performance • Ethernet control/connectivity.
which is settable by software to handle possible on a telephone line & uses • Two superb quality digital telephone hybrids.
a variety of PSTN and PABX systems with the same enhanced echo cancellation • Modular PSTN & ISDN telephony inputs.
varying impedances, call connection & algorithms as used on the DHY-03, the best • Hardware metering of send & receive levels.
disconnection tones. performing telephone hybrid in the world. • Send & receive level adjustment.
• Wide range of impedance matching options.
• Music on hold input.
• AGC, automatic gain control of send & receive
signals.
• Echo cancellation.
PI-6C Base Console Front & Rear
• Noise gate.
• Automatic caller ducking.
• Option for AES/EBU inputs & outputs.


Sonifex Product Update Sept10

Recommandé

Recommandé

Contenu connexe

Tendances

Tendances (16)

En vedette

En vedette (6)

Similaire à Sonifex Product Update Sept10

Similaire à Sonifex Product Update Sept10 (20)

Plus de Radikal Ltd.

Plus de Radikal Ltd. (20)

Dernier

Dernier (20)

Sonifex Product Update Sept10