SlideShare utilise les cookies pour améliorer les fonctionnalités et les performances, et également pour vous montrer des publicités pertinentes. Si vous continuez à naviguer sur ce site, vous acceptez l’utilisation de cookies. Consultez nos Conditions d’utilisation et notre Politique de confidentialité.
SlideShare utilise les cookies pour améliorer les fonctionnalités et les performances, et également pour vous montrer des publicités pertinentes. Si vous continuez à naviguer sur ce site, vous acceptez l’utilisation de cookies. Consultez notre Politique de confidentialité et nos Conditions d’utilisation pour en savoir plus.
Ce diaporama a bien été signalé.
Vous avez débloqué des téléchargements illimités sur SlideShare!
DATA COMMUNICATIONS & NETWORKING LECTURE-08 Course Instructor : Sehrish Rafiq Department Of Computer Science University Of Peshawar
LECTURE OVERVIEW Conversion methods Line coding Characteristics of line coding Signal level & Data Level Pulse Rate & Bit Rate DC Component Self Synchronization Line coding Schemes Unipolar Polar NRZ RZ Manchester and Differential Manchester Bipolar
CONVERSION METHODS OR ENCODING & MODULATION How information is transformed depends on its original format and on the format used by the communication hardware. Conversion methods Digital-to-digital conversion or Line coding Analog-to-digital conversion or Sampling Digital -to- analog modulation Analog -to -analog modulation
LINE CODING Line coding is the process of converting binary data, a sequence of bits to a digital signal. In other words, line coding converts a sequence of bits to a digital signal. At the sender, digital data are encoded in to digital signal. At the receiver, the digital data are recreated by decoding the digital signal back in to digital data.
SIGNAL LEVEL & DATA LEVEL The number of values allowed in a particular signal is known as the number of signal levels. The number of values used to represent data is known as the number of data levels.
DATA ELEMENT VERSUS SIGNAL ELEMENT A data Element is the smallest entity that can represent a piece of information this is the bit. A signal element is the shortest unit time wise of a digital signal. In other words data elements are what we need to send. Signal elements are what we can send. Data elements are being carried, signal elements are the carriers. r is defined as the ratio which is the number of data elements carried by each signal element.
DATA RATE VERSUS SIGNAL RATE The data rate is defined as the number of data elements sent in one second usually expressed in bps. Data rate is also called Bit rate. The signal rate is defined as the number of signal elements sent in one second. A signal rate is also called a pulse rate. A signal element is also called a symbol or pulse. One pulse or signal element can carry more than one bit. When a pulse or signal element carry only one bit then the bit rate and pulse rate/signal rate are same. The signal rate is sometimes called modulation rate or baud rate.
FORMULA FOR BIT RATEBit Rate=Pulse Rate x log2 LWhere L is the number of data Levels.
Example 1A signal has two data levels with a pulse duration of 1ms. We calculate the pulse rate and bit rate as follows:SolutionPulse Rate = 1/ 10-3= 1000 pulses/sBit Rate = Pulse Rate x log2 L = 1000 x log2 2 = 1000 bps
Example 2A signal has four data levels with a pulse duration of 1ms. We calculate the pulse rate and bit rate as follows: SolutionPulse Rate = = 1000 pulses/sBit Rate = Pulse Rate x log2 L = 1000 x log2 4 = 2000 bps
DC COMPONENT When the voltage level is constant for a while very low frequencies are often created. These frequencies around zero are called DC or Direct Current components. This component is undesirable for two reasons. First if a signal has to pass through a system (e.g. a telephone line which does not allow frequencies below 200 Hz) which does not allow low frequencies to pass the signal is distorted and may create errors in the output. Second this component is extra energy residing on the line and is useless.
SELF-SYNCHRONIZATION To correctly interpret the signals received from the sender, the receiver’s bit intervals must correspond exactly to the sender’s bit intervals. If the receiver’s clock is faster or slower, the bit intervals are not matched and the receiver might interpret the signals differently then the sender intended. A self synchronizing digital signal includes timing information in the data being transmitted. This can be achieved if there are transitions in the signal that alert the receiver to the beginning, middle or end of the pulse. If the receiver clock is out of synchronization, these alerting points can reset the clock.
Example 3In a digital transmission, the receiver clock is 0.1 percentfaster than the sender clock. How many extra bits persecond does the receiver receive if the data rate is 1Kbps? How many if the data rate is 1 Mbps?SolutionAt 1 Kbps:1000 bits sent 1001 bits received1 extra bpsAt 1 Mbps:1,000,000 bits sent 1,001,000 bits received1000 extra bps
UNIPOLAR SCHEME Digital transmission systems work by sending voltage pulses along a medium link, usually a wire or cable. In many types of encoding, one voltage level stands for binary 0,another level stands for binary 1. The polarity of a pulse refers to whether it is positive or negative. Unipolar encoding is so named because it uses only one polarity. The polarity is assigned to one of the two binary states, usually the 1. The other state usually 0 is represented by zero voltage.
PROBLEMS USING UNI POLAR SCHEME DC Component The average amplitude of a unipolar encoded signal is non zero. This creates a DC component. Lack of synchronization If the data contain a long sequence of 0’s and 1’s there is no change in the signal during this duration that can alert the receiver to potential synchronization problems.
POLAR ENCODING SCHEMES Polar encoding uses two voltage levels, one positive and one negative. By using the two Levels, in most polar encoding methods the average voltage level on the line is reduced and the dc component problem seen in unipolar encoding is alleviated.
NRZ(NON RETURN TO ZERO) SCHEMES In NRZ encoding the value of the signal is always positive or negative. Two popular forms of NRZ are: NRZ-L(Non Return to Zero-Level) In NRZ-L the level of the signal depends on the type of bit that it represent. The positive voltage usually means a 0 while a negative voltage means the bit is a 1. Problem: Long stream of 0’s or 1’s may create synchronization problem.
NRZ(NON RETURN TO ZERO) SCHEMES NRZ-I(NRZ-Invert) In NRZ-I ,an inversion of the voltage level represents a 1 bit. It is the transition between a positive and negative voltage, not the voltage itself, that represents a 1 bit. A 0 bit is represented by no change. NRZ-I is superior to NRZ-L due to the synchronization provided by the signal change each time a 1 bit is encountered. The existence of 1’s in the data stream allows the receiver to synchronize its timer to the actual arrival of transmission. A string of 0’s can still cause problems but because they are not as Likely,they are less of a problem.