Congratulations on having James Hardie products on your home!
We would like to share with you some basic information about
the products and how to care and maintain them. James Hardie
strongly recommends that the Homeowner understand how proper storage, installation and maintenance of James Hardie products will allow their beauty to last for many years to come.
1. The HardieZone®
System:
HZ5®
Care and Maintenance Guide
Congratulations on having James Hardie products on your home!
We would like to share with you some basic information about
the products and how to care and maintain them. James Hardie
strongly recommends that the Homeowner understand how proper
storage, installation and maintenance of James Hardie products will
allow their beauty to last for many years to come.
2. Your home’s exterior says a lot about you. Unfortunately, Mother Nature doesn’t care.
Whether it’s sheets of rain, dry heat, freezing temperatures, ice and snow, or hurricane
force winds, siding is under constant attack.That’s why for more than three decades,
James Hardie has continued to push back on everything Mother Nature could dish out.
Four million beautiful homes stand as a testament to our persistence.And as the most
trusted brand of siding in America, James Hardie has taken that level of defense to an even
higher level, with siding that’s engineered for climate.We call it The HardieZone System.
We based The HardieZon System on the eight individual climatic variables that primarily
affect long-term performance of siding. Using these factors we arrived at ten distinct
climatic zones.Though different, we found common variables in certain regions, allowing
us to engineer the HZ5 product line for zones 1 through 5 and the HZ10 product line for
zones 6 through 10.
The HardieZone® System
HZ5® Products
The HZ5 product line is right at home in climates with freezing temperatures, seasonal
temperature variations, and snow and ice. It is the result of our generational evolution of
our time tested products. To ensure that its beauty matches its performance we have
engineered the surface, giving it superior paint adhesion and moisture resistance. In
addition we have added a drip edge to the HardiePlank®
HZ5 lap siding product to provide
improved water management in conditions specific to HZ5 product climates.
• Resists damage from freezing temperatures
• Superior paint adhesion
• Noncombustible*
For additional HardieZone information, visit www.jameshardie.com.
*HardiePlank®, HardiePanel®, HardieShingle®, HardieSoffit®,Artisan® Lap products comply with ASTM E136.
Zones 1-5
Zones 6-10
3. Storage and Handling
Storage and Handling
If you have hired a contractor to remodel your home with new siding or have the
opportunity to watch your new home being built, it’s important for you to understand
how James Hardie siding should be stored and handled during construction. In general,
the product needs to be kept dry before installing it on your home. Our installation
instructions and this Best Practice Guide provide the installation crew and builder
with clear directions on how to properly store and handle all of our products.These
instructions and guide can be found on our website at www.jameshardie.com.
James Hardie products stored in their
original packaging.
If stored outside protect with an additional
waterproof covering.
One person should hold planks on edge in the middle
with arms spread apart for maximum support of the
product.
Two people should always carry panel products.
Carrying James Hardie®
siding products with ColorPlus®
Technology flat may cause excessive bending,
which can damage the finish.
!
Wrong Wrong
4. Installation
Installation
Homeowners are encouraged to take an active role during the installation of the product and work with the builder to ensure the product is installed
correctly. Our installation instructions and Best Practice Guide can be found on our website at www.jameshardie.com. If the instructions are not
followed when installing the products, the product only warranty could be voided.You should ask the product installer questions and bring up any
areas that do not seem consistent with installation instructions.The earlier these concerns are brought up, the sooner they can be corrected.
The general installation requirements for critical areas of the house are highlighted below. For complete details on what is required to install the
product, please refer to the specific installation instructions or the Best Practice guide where these construction details are discussed in greater detail.
Do not caulk
1/4” gap
Kickout flashing
Water-resistive
barrier laps
over the step
flashing and
the roofing felt
Roofing felt
Self-adhering membrane
Bottom piece
of step flashing
is cut and bent
to divert run
off water away
from the wall
Drip edge
and fascia
Gutter and end
cap should end a
minimum 1” from
siding
“L” Flashing
Flashing
Water-resistive
barrier
Trim
Cut trim
block into
two pieces
to retro-fit
around
existing
vent
Minimum 22.5° weather cut
Do not caulk 1/4” gap
Exterior slab
HardiePlank
lap siding
Water-
resistive
barrier
Wall sheathing
Starter strip
Deck
framing
HardiePlank
lap siding
Z-flashing
with vertical
element high
enough for
clearance
Water-resistive
barrier
Wall
sheathing
Starter
strip
Ledger
Flashing
over trim
with 1/4”
gap
Siding
Minimum, 1/2”
clearance between
the trim and
horizontal surface
Trim
Minimum
6-in.
clearanceGround
Siding
and trim
Minimum 2”
clearance
from slab
Min. 2”
clearance
from
highest
point of
decking
Sub-fascia
Ledger
Rafter tail
Sheathed
wall
Soffit
Drip edge Roof sheathing
Fascia
Blocking
Seal cut
edges
(of siding)
Roofing
SidingTrim
Flashing
Min. 2”
clearance
Extend shingles
at least 1 in. out
from the fascia
when gutters
are present
Flashing below
trim rests on
solid surface
Water-resistive
barrier
1/8” caulked
gap is left
between siding
and the side
trim pieces.
Starter strip Do not caulk between the siding
and the flashing, 1/4” gap
Flashing
General Installation Requirements
5. Cleaning and Maintenance
Water Management and Gutters
Whether you live in an area with high amounts of rainfall
or an occasional thunderstorm, it is important to effectively
manage the flow of water from these events for your entire
home. James Hardie recommends that you have gutters and
downspouts installed on your home if they were not already
present when you purchased the home.
Cleaning and Maintenance
Cleaning and maintaining the exterior of your home is an
important part of sustaining the beauty and value of your
home.The extent and nature of maintenance will depend on
the geographic location and exposure of the building.As a
guide, it is recommended that normal care and maintenance
tasks shall include but not be limited to:
• Washing down the exterior surfaces every 6 to 12
months with a garden hose or low pressure water
spray to remove dirt and debris.
- James Hardie Products with ColorPlus® Technology
can be cleaned using water and a soft brush or rag.
For stubborn dirt or stains, a mild detergent and a
soft brush may be used. For more information
see Tech Bulletin #20 Cleaning and Maintenance at
www.jameshardie.com
- For paint applied in the field, refer to your
paint manufacturer for washing and maintenance
requirements related to paint performance.
• Clean out your gutters, blocked pipes, and overflows
as required.
• It is important to re-apply caulking when it has
begun to show signs of wear. This can help keep
moisture from getting into the wall cavity. These
areas include but are not limited to penetrations,
flashings, plank and trim connections and in some
cases between plank joints.
- James Hardie recommends the use of caulks
and sealants that remain permanently flexible.
Look for the words “permanently flexible”
written clearly on the label or in the
accompanying literature. For best results use
an Elastomeric Joint Sealant complying with
ASTM C920 Grade NS, Class 25 or higher, or a
Latex Joint Sealant complying with ASTM C834.
Caulking/sealant must be applied in accordance
with the caulking/sealant manufacturer’s written
instructions or ASTM C1193.
• It is a good practice to keep vegetation such as
shrubs, bushes, and small trees trimmed back and
away from the home and siding. This will also help
to ensure that sprinkler systems do not saturate
areas near the building.
• Ensure required external ground clearances
(typically 6”) and drainage slopes are maintained.
Do not in fill landscaping up to the siding.
High pressure water blast and sand blasting may damage the surface
of the fiber cement product. Low pressure water spray, a soft medium
bristle (nonmetal) brush is most suitable for cleaning fiber cement
products.Acid washing can damage the fiber cement surface and is not
recommended. Note: If using a pressure washer, care must be taken to
ensure that the water stream does not damage the surface of the siding.
Damage to siding arising from improper cleaning or maintenance may not
be covered by the James Hardie warranty. Using wide fan tips that are kept
a minimum of 6 feet from the wall and at pressures under 1500 psi will
minimize the chance of damaging the siding.
!
It is a good practice to keep vegetation such as shrubs,
bushes and small trees trimmed back away from home
and siding.