11. JK White CementUsage Flooring with White cement Walls with White cement Plastering Decorative/Utility Architectural Your Smile.. Our Satisfaction
12. Flooring with ..JK White Cement(Under bed for marble) Your Smile.. Our Satisfaction Marble Being Translucent will reflect part of the background. Hence a white base will Enhance the whiteness of the Marble which Can Be Achieved using JK White Cement
24. Plaster with .. JK White Cement Your Smile.. Our Satisfaction Textured Plaster Textured coating applied on exterior for decoration & protection. Texture is made by chiseling.( Malad Stone) Variety of colors with pigment addition to white cement Plain Plaster Plain plaster without any texture. Variety of colors with pigment addition to white cement. Plastering is done on grey cement plaster surface which is made rough by combing Roller Finished Plaster Special textured rollers are used to give textured & uniform pattern. Immense design variation possibilities. Variety of colors with pigment addition to white cement.
48. Properties Your Smile.. Our Satisfaction Transverse Strength - 1.7 Kg/cm2 Compressive Strength - 37 Kg/cm2 ( 28 days) Whiteness Index - 93% (28 days) Pot life - 180 Minutes Water demand by volume - 35 to 40 % Surface hardness - 3.0 N Maximum thickness of total - 1.5- 2.5 mm coats Coverage - 15 Sq Feet/Kg in 2 coats* Subject to wall condition /Roughness and usage
49. JK COARSE PUTTY USED IN UNDULATED SURFACE THICKNESS – 4 MM MINIMUM MICRO SAND INCLUDED IN THIS PUTTY SPECIAL PRODUCT AVAILABLE IN 20 KG BAGS. FINAL FINISH WITH FINE PUTTY ONLY. WIDELY USED IN TEXTURE FINISHES IN ELEVATIONS. CAN GO UPTO 8MM THICKNESS IN 2 COATS.
50. JK WALL PUTTY.. Surface Preparation Your Smile.. Our Satisfaction Surface Preparation The surface should be cleaned to make it free from dirt, dust, grease, oil and paint. All foreign impurities should be removed with a wire-brush. Wall surfaces should be cured so that the surface is saturated with water yet in ‘touch dry’ condition. Treatment of New Surface The new surface requires only soft treatment such as removal of dust, dirt and foreign matter. In case of cracks, voids and damages; it should be patched up prior to application of J. K. Wall Putty with grey/white cement. Treatment of Old Surface All loose material and/ or organic growth must be removed with Putty blade or brush. In case of old painted surface scrub the surface with coarse emery stone/paper.
51. JK WALL PUTTY.. Application Your Smile.. Our Satisfaction Preparation of J.K. Wall Putty Paste J. K. Wall Putty is a fine powder. Mix slowly J. K. Wall Putty with approx. 40% water by volume to prepare paste of desired consistency. Mix vigorously for 5-10 minutes for making lump free, uniform and smooth putty paste. Product should be mixed in required quantities to be used within 2-3 hrs of its preparation. Application Apply uniformly the first coat of J.K. Wall Putty with blade/trowel on the wall from bottom to top. Apply second coat after the first coat has dried completely(Min 6 hrs). Limit the total thickness of 2 coats to 2.5 mm. Allow complete drying and then use fine emery paper to remove the application mark if any. Any kind of paint can be applied on this surface. Use water for curing before applying paint. Precaution Although J.K. Wall Putty does not contain any toxic material, use rubber gloves while mixing, as prolonged exposure with water may soften the skin resulting in fine cuts/legions due to cement particles. Precaution should be taken to avoid dust inhalation while handling the powder putty. Storage Store J.K. Wall Putty in a dry place and open the pack just before use. Keep out of reach of children.
76. Your Smile.. Our Satisfaction J.K. Waterproof reacts with alkalis in the concrete forming a highly water-repelling compound in the capillaries and throughout the concrete or mortar. In this way, the surface tension, which would normally draw water into the capillaries and micro cracks does not take place and does not allow propagation of Moisture How does it Work?
