1. Wingtip missle rail (make 2 from 1/4" x 3/8" balsa)
Internal inlet top
(Make 2)
Canopy
minate)
(Make 8 and la
Turtledeck top
(Make 2)
top
elage
F wd fus e 1)
(Mak
piece
Canopy sill
(M ake 4)
Inlet diverter
top piece
(Make 2 from
3mm Depron)
Aft fuselage
top doubler
2
(Make 2)
Canopy top template to aid carving
ubler 2
top do
selage
Fwd fu (Make 2)
Aft fuselage top
doubler 1
(Make 2)
p dou bler 1
elage to
Fwd fus (Make 2)
Inlet diverter
center piece
plate (Make 2 from
top tem
econe shaping
3mm Depron)
Nos doublers
to aid n lines indicate
Dashed gree
Fwd fuselage side F4
F3
(Make 2)
)
F2
th
ng
re
.22" carbon tube spar
st
Stabilators
tr a
ex
(Make 2)
or
F1
lf
na
io
ne
pt
Noseco minate)
(o
and la
s
10 To make the canard strong enough, either:
(Make
ge
1) Make the entire canard from 3/16" sheet balsa
ed
ls a
2) Make from foam but edge with hard balsa as shown
Ba
3) Make from foam and fiberglass the top and bottom
doubler 1
F1 F2 Cut slot for .22" carbon
Fwd fuselage bottom
(Make 2) tube pivots
ng in .5"
(o t
th slo
re r 1
)
pt
st pa x 1
xt ply mm
doubler 2
Fwd fuselage bottom
re " 6
ra s
(Make 2) t)
fo 1/32 ert
op
s(
s
Place 1" wide strip of fiberglass
In
ge
ed chordwise at root (top and bottom)
l sa
ak rd
2)
Ba
(M ana
F3
e
F4
C
for
esign
strake d
icate ariants
es ind v
ed lin ard Su-30
ash
Red d non-can Wing fillet lamination 1
(Make 2)
Wing
(Make 1)
Canard braces (6 deg dihedral)
(Make 4 from 1/32" ply)
Wing fillet lamination 3
(Make 2)
sign fo r
trake de
es in dicate s riants
shed lin -30 va
Red da on-canard Su
n
r Cut slots to fit tabs in
ke de sign fo nacelle sides (typical)
te stra
indica 0 variants
ashed
lines Su-3
d Wing fillet lamination 2
Red d non-canar
(Make 2)
Splice wing here to fit
on one sheet of Depron
Forward fuselage bottom
(Make 1)
Re d d a s
hed line
Aft fuselage spine--bottom
s Insert 1/32" ply
non-can indicate strake spar inside slot
ard Su-3 d
0 varian esign for
(6mm x 4.0")
ts
(Make 1)
Trim as shown for twin motor installation
Outboard nacelle side .75" square x 1/16" ply bearing supports
(Make 2)
Dash
ed r
for S ed line s
u-30 ho
varia ws tip
nts
Rudder control horns
Aft fuselage spine--top
(Make 2 and laminate)
(make 2 from 1/32" plywood)
In 32" tra
1/ ex
se p str
fo
rt ly s en
r
6m p g
m ar i th (
x n s op
11 lo t)
Outboard
Inboard
Inboard nacelle side
.5 t
.75" square x 1/16" ply bearing supports
"
(Make 2)
Glue one doubler to
control horn as shown
1/2" dia.
if using single motor
Trim off this part
Stabilator control horn
Nacelle tops
Stabilator control horn doublers/end stops
(Make 2)
(Make 2 from 1/16" ply) (Make 6 from 1/16" ply)
Vertical tail
(Make 2)
Nacelle bottom
Note: If using a motor other than the LSPJ,
(Make 2) modify the height of the side plates to ensure
Epoxy to motor Epoxy to motor the centerline of the motor is aligned with the
stick here stick here
pivot bolt (to minimize strain on the servo)
Centerline spike
(Make 1)
lot
"
Side plates for thrust
1/32" 6mm x 8.5
ar in s
vectoring motor mount
ply sp
(Make 2 each from 1/8" ply)
Insert
if using single motor
Trim off this part
3.13"