1. BASIC RIGGING
TRAINING MANUAL
COMPETENCY BASED TRAINING TO THE NATIONAL
OCCUPATIONAL HEALTH & SAFETY STANDARDS
1
2. THE ACT
The Act is designed to provide a broad framework, which allows employers, and employees
to be flexible in their approach to achieving the standards set in the legislation. The
substantive legislative provisions are limited to stating objectives and general duties and
providing the machinery to establish a framework for standards development and
enforcement. Details of issues broadly covered by the Act are provided in regulations and
codes of practice. These regulations and codes of practice are revised from time to time to
keep pace with developments in industry. The Act provides for the repeal of a number of
other Acts which to date have regulated various activities relating to occupational health and
safety.
GENERAL DUTIES
The Act imposes duties on employers and employees, the self-employed, occupiers and
manufacturers and suppliers of plant, equipment and substances used in the workplace. The
object of the Act in imposing these duties is to ensure that those with the requisite authority
or control over particular aspects of the working environment exercise that authority or
control in a manner that is not harmful to the health or safety of any person.
WHAT ARE THE OBJECTS OF THE ACT?
Essentially, the Act provides a framework for improving standards of workplace health and
safety and reducing work related accidents and diseases.
The objects of the Act are:
To secure the health, safety and welfare of persons at work,
To protect persons at work against risks to health or safety;
To assist in securing safe and healthy work environments:
To eliminate, at the source, risks to the health, safety and welfare of persons at work:
To provide for the involvement of employees and employers and associations representing
employees and employers in the formulation and implementation of health and safety
standards.
The objects should be looked at when interpreting the different sections of the Act.
EMPLOYER DUTY
The duty of employers towards employees is set out in Section 21.
Employers are required to 'provide and maintain so far as is practicable for employees a
working environment that is safe and without risks to health'.
2
3. Section 21 (2) sets out a number of specific duties which are examples of what is necessary
in order to comply with the general duty. These include:
Providing and maintaining safe plant and systems of work (for example regulating the pace
and frequency of work);
Arranging safe systems of work in connection with plant and substances (for example toxic
chemicals, dusts and fibres),
Providing a safe working environment (for example by controlling noise or vibration levels),
Providing adequate welfare facilities (for example washrooms, lockers, dining areas),
Providing adequate information on hazards, as well as instruction, training and supervision
to employees, to enable them to work safely.
Employers owe the same duty to independent contractors and their employees who are
working at the workplace. This duty extends only to matters over which the employer has or
should have control. This covers, for example, large worksites where there is an overall
employer and many independent contractors performing different types of work.
Furthermore, employers are required, so far as is practicable, too:
Monitor the health of their employees (for example by conducting audiometry testing),
Keep information and records relating to the health and safety of their employees (for
example results of tests, records of injuries and illnesses and their causality),
Employ or engage suitably qualified persons to provide advice to them in relation to the
health and safety of their employees (for example in large firms this could mean the full time
employment of an occupational health nurse, a safety officer or hygienist -in small firms it
may mean engaging outside specialist advice when it is required),
Nominate a person with an appropriate level of seniority to be the employer's representative
when health and safety issues arise or when health and safety representatives carry out their
functions under the Act,
Monitor conditions at any workplace under their control and management (for example by
testing noise levels, testing levels of employee exposure to harmful substances); and
Provide information to their employees, in such languages as are appropriate, with respect to
health and safety at the workplace, including the names of persons to whom an employee
may make an inquiry or complaint in relation to health and safety.
EMPLOYEE DUTY
The duties of employees are set out in section 25
Section 25 was amended in 1993 and
“While at work employee must
3
4. (a) Take reasonable care for his or her own health and safety and for the health and safety of
anyone else who may be affected by his or her a, or omissions at the workplace; and
(b) Co-operate with his or her employer with respect to any action taken by the employer to
comply with any requirements imposed by or under this Act. "
In addition, employees must not wilfully or recklessly interfere with or misuse safety
equipment that is provided. They must not wilfully put at risk the health and safety of others.
"Practicable" means practicable having regard to-
(a) The severity of the hazard or risk in question;
(b) The state of knowledge about that risk and any ways of removing or, that hazard or risk;
(c) The availability and suitability of ways to remove or mitigate that hazard or risk;
(d) I the cost of removing or mitigating that hazard or risk;
BASIC RIGGING
The scope of work for this certificate is dogging and rigging work associated with-
(a) Movement of plant and equipment;
(b) Steel erection;
(c) Particular hoists, *
(d) Placement of precast concrete,
(e) Safety nets and static lines; **
(f) Mast climbers; ***
(g) Perimeter safety screens and shutters; and
(h) Cantilevered crane loading platforms- ***
But excludes work involving:
(a) Use of load equalising gear;
(b) Rigging of cranes, conveyors, dredges and excavators;
(c) Tilt slabs,
(d) All hoists with jibs and self-climbing hoists;
(e) Demolition;
(f) Dual lifts,
(g) Rigging of gin poles and shear legs,
(h) Flying foxes and cable ways;
(i) Guyed derricks and structures; and
(j) Suspended scaffolds and fabricated hung scaffolds.
This certificate encompasses the requirements for the dogging certificate
4
5. NOTE:
* The erection/dismantling of cantilever platform hoists with a WLL < 500 kg (materials
only) may also be carried out by persons holding a Basic Scaffolding Certificate or
equivalent.
* * Persons holding a Basic Scaffolding Certificate or equivalent may also carry out the
erection/dismantling of safety nets and static lines.
*** Persons holding an Intermediate Scaffolding Certificate or equivalent may also carry the
erection/dismantling of cantilevered crane loading platforms and mast climbers.
General rigging appliances Chain blocks Chapter 7 A guide to rigging
Chain blocks should comply with AS 1418.2 Serial hoists and winches. Some could be
dangerous and fail under load. If in doubt check with the supplier.
Chain blocks are used for short lifts such as by small monorail cranes, fixed hoists and so on.
They are also frequently used by riggers for transferring or "fleeting" loads from purchases.
Do not drop a chain block. The jolt may distort the casing causing the gearing to malfunction
and the chain block to fail. The drive pinion could also part from the main driving spur
wheel.
Make sure that the hook has not dipped through itself in a two part or multiple chain fall
causing the load chain to twist. Keep blocks away from sand, grit and dust. Some people
keep the load chain lightly oiled to create less friction as the chain passes over the gypsy. If
the chain is oiled and it becomes covered in sand or grit, the grit becomes a grinding paste
which wears the chain very quickly.
The gypsy in one manufacturer's chain block may not be identical to another. It is important
when ordering replacement chain, that the chain and the gypsy are compatible.
Chain blocks with multiple fails are often very heavy on the opposite side to the block. It is a
good practice to mouse the block to the head sling, to prevent the hook from dropping out of
the head sling when the weight is released from the block.
Maintenance
Inspect the brake lining material for signs of wear and have it replaced if necessary, ensuring
the retaining rivets (if any) are well countersunk.
Check the pawl for sharpness and alignment, the pawl spring for effectiveness, and the
ratchet teeth for sharpness and wear.
Check the bearing bushes for wear and have them renewed if necessary.
5
6. Remove the gear case and inspect the gears for wear on the shafts, and also for bending,
breakage, wear, and misalignment of teeth.
Check the load chain for wear and for stretch and the load sheaves for excessive wear. If the
load chain does not fit accurately it should be replaced before using the block.
Inspect the load chain guide for movement. This guide should be the fixed type not a small
roller. The purpose of the guide is to guide the load chain, free of turns, on to the gypsy. If a
roller guide is fitted, hang the block up and while lowering the empty hook, gently twist the
ascending chain as it approaches the guide roller.
If it jams, a new guide must be fitted. Check the hooks for opening out due to overloading or
misuse. Examine the hook yokes, ball bearing swivels and anchorages of chain to clevis
pins.
Page 74
CHAIN PULLERS
Chain pulley block
Versatile tools with almost unlimited applications. Can be used in vertical or horizontal
position, or at any angle. Light-weight, compact and durable, low headroom and low
operating effort.
DO'S AND DON'TS SAFETY PRECAUTIONS
Safe Operation of Hoists
The following are Do's and Don'ts for safe operation of any hoists. Taking precedence over
any specific rule listed here. However it is the most important rule of all, USE COMMON
SENSE. A few minutes spent reading these rules can make an operator aware of dangerous
practices to avoid and precautions to take for his own safety and the safety of others.
Frequent examinations and periodic inspections of the equipment as well as a conscientious
observance of safety rules may save lives as well as time and money.
6
7. DONOTS - HOISTS
1. NEVER lift or transport a load until all personnel are clear.
2. DO NOT allow any unqualified personnel to operate hoist.
3. NEVER pick up a load beyond the capacity appearing on the hoist. Overloading can be
caused by jerking as well as by static overload.
4. NEVER carry personnel on the hook or the load.
5. DO NOT operate hoist if you are not physically fit.
6. DO NOT operate hoist to extreme limits of chain or rope.
7. AVOID sharp contact between two hoists, between hoist and end post and hooks and
hoist body.
8. DO NOT tamper with any parts of the hoist.
9. NEVER use the hoist rope or chain as a sling.
10.DO NOT divert attention from load while operating hoist.
11.NEVER leave a suspended load unattended.
12. DO NOT attempt to lengthen load chain. or to repair damaged load chain.
13.DO NOT use chain or rope as grounding rig for welders, NEVER touch a live welding
electrode to the chain or rope.
DO'S - HOISTS
1. READ and follow manufacturer's instruction, installation and maintenance manuals.
When repairing or maintaining a hoist, use only manufacturer's recommended parts and
materials.
2. READ and follow all instruction and warning information on or attached to a hoist.
3. REMOVE the hoist from service and thoroughly inspect and repair as necessary if
unusual performance or visual defects (such as peculiar noise, jerky operations. or travel in
improper direction or obviously damaged parts) are noticed.
4. ESTABLISH a regular schedule of inspection and maintain records for all hoists with
special attention given to hooks, ropes, chains. brakes and limit switches.
5. CHECK operation of brakes for excessive drift.
6. CHECK operation of limit switches.
7. CHECK for damaged hooks, ropes or chain.
8. KEEP load chain or rope clean and well lubricated.
9. CHECK the wire rope or chain for improper seating. twisting. kinking. wear or other
defects before operating the hoists.
7
8. 10. CHECK for broken wires in wire rope. Twelve randomly distributed broken wires *in
one rope lay or four broken wires in one strand in one rope lay are sufficient cause for
replacement.
11. MAKE SURE a load clears neighbouring stock piles, machinery, or other obstructions
when raising, lowering. Or travelling the load.
12.CENTER hoist over the load before operating.
13.AVOID swinging of load or load hook when travelling the hoist.
14 BE SURE the load attachment is properly seated in the saddle of the hook. Balance the
load properly before handling. Avoid tip loading.
15.PULL in a straight line. So that neither the hoist body nor load chain or rope are angled
around an object.
16.MAKE SURE you take up slack slowly.
17.ON LEVER OPERATED HOISTS. Always release handle gradually when under load to
avoid flying handle.
OPERATING AND SAFETY PROCEDURES
1. When preparing to lift or move a load be sure that the attachments to both hooks are
firmly seated in the saddles of the hooks. Avoid off-centre loading of any kind especially
loading on the point of the hook.
2. When lifting or pulling, raise or move the load only enough to clear the floor or support.
Check to be sure the brake will hold the load and that the attachments to hooks and load are
firmly seated. Continue the fill only after you are assured the load is free of all obstructions.
3. Do not load beyond the rated capacity. Overload can cause immediate failure of some
load carrying part or create a defect causing future failure at less than rated capacity.
4. Do not use an extension on the lever. A need for an extension is an indication of either an
overload or an incorrectly maintained unit. Use a Tool of adequate capacity, which is in
good operating condition. Under no condition should any attempt be made to pry the ratchet
plunger out of engagement when a load is on the unit. As this allows the load to fall.
6. Do not use this or any other overhead materials handling equipment for lifting persons.
7. Stand clear of all loads and avoid moving a load over the heads of other personnel. Warn
personnel of your intention to move a load in their area.
8. Do not leave the load suspended in the air unattended.
9. Do not lower load chain to the point where the end ring becomes jammed against frame.
10. The CM Series 640 Lever Toot has been designed for hand powered operation only.
8
9. 11. Do not wrap the load chain around the load and hook it onto itself as a choker chain as
the chain is calibrated, therefor it is only designed for a straight pull.
This also could result in the loss of the swivel effect of the hook which could mean a twisted
chain and jammed lift-wheel.
13. Do not operate the tool unless it is rigged to pull in a straight line from hook to hook, and
the frame is free to swivel on the upper hook. Refer to illustration below.
Pull lifts
There are two types of lever operated load pullers
FSWR Cable pullers (Drum type + Creeper type)
CHAIN Pullers (Calibrated chain puller + Bush roller chain puller)
Where a chain block needs major overhaul or repair, advice should be sought from the
supplier about the work to be carried out, and should be done by people who are competent.
Chain blocks must be lubricated lightly. If too much grease is pumped into a chain block the
grease could cover the brake and the chain block would fail.
Do not leave a chain block soaking in oil. The oil will saturate the brake.
1. Those fitted with bush roller chain.
2. Those fitted with calibrated chain.
A load supported by a bush roller chain pull lift should either be in guides or fixed into a
position where side pull cannot be placed on the chain.
Do not extend the handle to give extra leverage. Doing this will overload the pull lift.
Inspection and maintenance is similar to chain blocks.
There are two types of FSWR lever operated pullers:
The drum type + The creeper type.
The drum type has a safety ratchet and pawl. The pawl must be held by hand when lowering.
Do not tie the pawl back because this can cause control to be lost.
9
10. The IFSWIR used in these winches must be the type recommended by the manufacturer.
The inspection of the FSWR and the anchorages must be done daily to ensure that the winch
is safe to hold the load. A complete inspection must be done monthly, with particular
attention to the hoist rope.
Creeper type lever operated pullers have an advantage over drum type pullers because they
have unlimited drift. Without gears, pawls and ratchets, the design enables the rope to pass
through the unit in a straight line and is not wound on a drum.
75
Two pairs of forged steel jaws control the lifting and lowering of the load by a hand lever.
The weight of the load actuates the jaws. The wire rope is at all times held by one pair of
jaws while the other pair having been opened by cams, is moved by the lever for the next
gripping or pulling motion. This method draws a wire rope of any length through the unit.
Caution: The rope can slip through these types of pullers because of the constant diameter
in the cam gripping mechanism and because FSWR reduces in diameter under constant
loading.
WIRE ROPE
Kink is a fatal defect of wire rope. Unwind the coiled wire rope correctly as per manufacture
recommendations not to twist and kink the wire rope.
Never press the wire rope onto something with a sharp edge.
If the wire rope is hung onto the edge, the breaking load of wire rope will come down
sharply as per following table.
Rope Angle 120 90 65 45
Braking Load 30 35 LO 47
Reduction in percentage
SMOOTH OPERATION
Place the hook on the ground, hold the machine at an angle and push down on the clutch
release "P" towards the anchoring hook until it is seated in the notch.
Pull the rope through the machine until the required length is reached.
Close clutch "P".
10
11. Forward or lifting motion. Place the handle on the lever '11 ", then pull and push
alternatively.
Reverse or lowering motion. Place the handle on "L2", and work with the same motion.
Release, pull and push alternatively on '12" to slacken the rope, then declutch "P"
Don't over-load.
All pullers provide safety pins for over load. But please be shore to use pullers within the
maximum capacity as specified, to ensure longer machine life and prevent any accident
caused by over loading,
If safety pins are sheared by over load, replace them with spare safety pins. Replacement
safety pins are provided in the Carrying Handle. Don't make any temporary repair by using
screws, steel wire. Otherwise you cannot prevent any overloading.
OPERATING HANDLE
Never operate Operating Lever and Reversing Lever simultaneously.
Operate handle with maximum swing distance.
Locate the handle onto the operating lever and make it turn approx. 90* so that pipe handle
dose not come off from the operating lever whilst in operation.
AFTER USE OF PULLER.
Return the Rope Release handle to the original position, otherwise the spring will loosen and
could cause future machine problems.
Lubricate the machine after Wiping out the dirt and moisture.
Oil wire rope after cleaning.
For preventing rust, don't keep the machine at the place where moisture is prevalent or
chemicals are stored.
Do not drag or throw pullers.
IN CASE OF MACHINE TROUBLE
Check lubrication. 98" of machine trouble is caused by poor lubrication.
Check safety pins.
Check wire rope of no defects.
Confirm that the inside of the machine is not rusty or not dirty.
After checking above item above and if no good results obtained, please contact the dealer
or manufacturer.
11
12. Packing. securing and moving loads Chapter 10
Packing Packing must be able to support the load and the base of the footings of packing
should be hard and level. If the footing is earth, a layer of sand should be spread over the
area. Make sure that the base area of packing is large enough to support the load.
Check that there are no services such as large diameter pipes, tanks and cellars under the
packing, especially if a heavy load is to be placed on the packing.
Do not place bearers in line above one another, as the packing can roll and collapse.
During lifting operations, keep filling the gap with packing until larger bearers can be
inserted. Follow-up packing must be adjusted as the load rises.
Pigstying is an effective method of supporting a load with criss Pigsties or crossed timber
packing. Each layer is set at 900 to the layer below.
cribbing The footing base must be large enough to support the load and the main load
support bearers must be at right angles to the load.
Sleepers which are all slightly different sizes are often used for pigstying. To ensure there is
no movement the second layer must be packed with wedges or thin packers (gluts).
CORRECT
106
Spreader beams
Spreader beams are devices which spread the load evenly for a given lift. They are generally
made to suit a particular job. Most have a central lifting point for the crane or lifting
medium, and have two or more lugs underneath to take the load slings.
All spreader beams must be suitable to lift the particular load and must be branded with the
WLL. The WLL must include the weight of the load plus all lifting gear (slings, shackles
etc).
Some spreader beams are fitted with off-set lugs on the top and are designed to raise loads
level even though they are heavy on one end.
For example, there are types of spreader beams used in power
stations with sliding lifting lugs used to fit the rotor into the stator.
This is done by sliding the lugs along the spreader until the rotor is
level.
12
13. There are loads such as pre-stressed concrete beams which are designed to take downward
forces only. This is opposite to the forces imposed by lifting in the centre.
There are two methods of overcoming this problem:
Use slings of sufficient length so that the beam can be lifted
near the ends and still have a safe angle. For this method to be
successful the crane or lifting medium has to have enough drift
o place the beam into position.
Use a spreader beam of sufficient length and strength to lift the beam. This method is the
best if drift is a problem.
76
Equalising gear
Slinging loads lifted by two cranes. Use of equalising sheave.
Equalising sheaves are load supports, which transfer the load from one single point to two
others by means of FSWR. Chain and fibre rope are rarely used. There are several different
types of equalising gear, which all do a similar job.
Equalising sheaves transfer the weight on the single point equally to the two points which
take half the load each.
If the two points are of unequal capacity, the load on the single point should never exceed
double the capacity of the weakest of the two other lifting points.
If one of the two lifting points remains stationary and the other hoists up, the sheave is then a
hauling sheave not an equalising sheave. Friction must then be taken into account when
working out the weight on the hauling part.
If the capacity of the crane is equal to the load imposed on the crane then the capacity could
be exceeded by the additional load due to friction in the sheave system.
Equalising sheaves are often used on bridge or gantry cranes which have a four part
purchase with two hauling parts attached to the hoist drum. The opposite or stationary side
passes over an equalising sheave.
The function of the equalising sheave is to move as the hoist block swings sideways. The
part of FSWR that passes over the sheave has abrasion and fatigue. It takes half of the
weight of the hoist block at all times. It also takes half the weight of the load, plus half of the
weight of the hoist block when the crane is lifting. It is the hardest working piece of rope on
the crane and must not be overlooked by maintenance personnel.
Slinging from an equaliser beam with bowsings
77
13
14. LIFTING LOADS: JACKS
Jacks are very dangerous if not used in a safe manner, they have a small base compared to
their lifting capacity and tilt very easy, they are used when it is not suitable to use a crane or
hoist to raise or lower a load.
Only lifting jacks with a working load limit are to be used. Car jacks have no rated WLL and
should not be used as load lifting jacks. Do not exceed the WLL branded on jacks. Jacks
should be placed on a timber pad and have a timber pad placed on the head to prevent
slipping.
One of the main dangers of using jacks is the height of the object to be lifted is always
higher than the jacks so it is important to make shore that all the sides are supported to stop
the load slipping.
Screw or bottle jacks should be checked very closely, as the pull in the tommy bar in the
screw head can cause the jack to shift. Examine the condition of the pawl, the teeth of the
ratchet, and the handle. Make sure that they are in good condition before lifting. Test the
operation of the quick release before lifting a load
LIFTING
Make sure the load is kept steady while raising the load. Do not lift both ends of the load
simultaneously. Use the lowest gear when lifting a load near to the maximum capacity of the
jack. The lift must be vertical. If the jack shows signs of tilting, pack the load, release the
jack and reset. Do not extend the jack handle to increase leverage because this will overload
the jack. Take care when releasing the ratchet from the pawl during lowering. Control can
easily be lost with the likelihood of injury.
When using Hydraulic jacks use the correct oil and make sure the oil reservoir is full and
free from dirt or grit.
14
15. SCREW JACK HYDRAULIC JACK
RATCHET JACK SCREW JACK WITH RATCHET
LIFTING BY LEVERAGE
Lifting by leverage is something we use in a restricted area, for example: lifting an object to
put skates under to move the object to another location. In all cases with leverage we use the
fulcrum principal witch is load multiply by distance from centre of load to fulcrum then
divide the distance fulcrum to effort point, which will give you the effort in kilograms.
The danger of lifting by leverage is not knowing what the braking strain of the lever is for
example: the allowable stress in bending a length of hard wood timber has a 900 pounds per
square inch allowable stress for extreme fibre hard wood (permissible working stresses for
structural timber) find the stress point out before the injury accurse
600 x 2 / 3 = 400 kg of effort
15
17. ------------------------------------------------------------------------------------------------------------
Fixed cantilevered beams
Cantilevered beams (needles) bolted down to floor beams and held
by counterweighting or other means are often used for single whip
hoists, to support a block and tackle, or a chain block.
A cantilever must be set up so that no more than 1/3 of the length protrudes beyond the outer
point of support. An engineer should make the calculations for steel beams. For timber
needles see the tables that follow.
80
Formula for determining uplift
Total weight x projection = W x P = uplift Example
Inboard distance L Weight to be lifted = 2 tonne
Projection = 1 metre
Formula for determining counterweight Inboard distance = 2 metre
Total weight X Dromection x safety factor Safety Factor = 3
Inboard distance uplift = W x P
L
W x P x SF = counterweight =2xl
L 2
= 1 tonne uplift
counterweight = W x P x SF
Inboard
=2x1x3
2
=6
= 3 tonne counterweight
17
18. Chapter 12
Cantilevered crane loading platforms
Cantilevered crane-loading platforms (CCLPs) are temporary platforms which are often used
during the construction or demolition of multi-storey buildings and structures so that
materials and equipment can be shifted to or from floor levels.
The platform is generally cantilevered from the face of the building to allow loads to be
directly raised or lowered by tower cranes or mobile cranes.
CCI-Ps can also be used for other purposes such as catch platforms to contain failing debris
at the building perimeter and as supporting structures for scaffolds constructed at the
building perimeter. They are sometimes set up in a simply-supported mode such as over
penetrations or voids, for use as loading platforms, access platforms or protection decks.
CCI-Ps are available in a variety of designs including fully fabricated and demountable
types. They may have either fixed platforms or rolling platforms. Their needles can be
anchored to the supporting structure in several ways, such as through-bolting, bolting into
castin inserts, or reveal-propping. Reveal props may be purposedesigned, integral
components or they may be general-purpose adjustable building props laced together with
scaffold tubes and couplers.
CERTIFICATION
The installation and dismantling of CCI-Ps must be carried out (or directly supervised) by a
person holding either the Basic Rigging certificate or the Intermediate Scaffolding certificate
(or equivalent old certificates).
Whenever a CCILP is located or removed by a crane, the slinging and load direction must be
controlled by a person with a Dogging or Rigging certificate (or equivalent old certificate).
The propping of CCLPs with adjustable building props and scaffold tubes and couplers or
other types of scaffolding equipment must be controlled by a person with an Intermediate
Scaffolding certificate.
The platform
The platform needles should be positively secured against lateral displacement.
A minimum of two signs stating both the maximum uniformly distributed load and the
maximum concentrated load that the platform can carry must be in clear view on the
platform.
The platform decking should be flush with and abutting the floor slab, otherwise suitable
ramps should be fitted.
There should not be any gap between the platform and the site handrails.
18
19. Platforms located on the side of a building facing a public roadway should not extend
beyond the line of the overhead protection provided for the public.
128
Relocation of The floor area where the platform is to be moved to, and the floor crane
loading area where the platform is to be moved from, should be barricaded platforms to
prevent unauthorised persons from entering into the area while the change is made.
Perimeter fencing must be removed while the change is made. No person should work near
the unfenced perimeter edge unless attached to the building by a safety harness. The area
below the platform relocation must be barricaded and spotters provided where necessary.
Clear all loose objects from the platform before the platform is lifted by the crane. Perimeter
fencing (handrails) should be replaced immediately after moving the platform. All bolts
must be placed back in the respective vacant holes when erecting or dismantling. The lifting
position must be clearly marked with signs painted on the platforms. The lifting lugs should
be engineer designed to lift the platform. Props must be correctly secured at the top and also
at the base by bolting, welding, or other suitable securing method to stop any lateral
displacement. The tare weight of the platform must be displayed on the platform. Some
platforms have a rubbish bin inserted under the platform deck. The rubbish bin must be
removed and emptied before the platform is shifted. A waterproof sheet with instructions
should be attached to the platform showing all operational and safety instructions of how to
use, and lift the platform.
Before the platform can be used:
• All bolts or connectors must be secured and tightened in position.
• All props must be plumb and have the rear ties in position.
• Adjustable props must be adjusted to ensure minimal adjustable jack extension.
• Rear handrails must be in position.
• The side panels and gates must be positively fixed in position.
Gates must be closed at all times except for long loads. All platforms must be kept clean and
clear of loose materials.
Platforms should only be used in the manner for which they were designed. Any alterations
or different use of the platforms should be to an engineered design.
129
Rolling CCLPs are platforms which can be rolled inside the building and back out
again for ease of loading and unloading.
19
20. The two braces at the front of the platform, and the two locking pins on the left and
right side must be in position and secured at all times for lifting, transporting and use
as a loading platform.
The tie bar at the rear of the platform is to be used at all times when lifting or
transporting the platform.
The spreader bar under the platform is to be secured and in position at all times.
Move the platform deck forward until it connects with the end of the beam. Secure the
left and right side locking pins. Close the gates and place the left and right brace in
position. To move the platform backwards, reverse the procedure.
127
Parbuckling
Parbuckling is a method of using two parts of rope to unload drums or cylindrical objects
from trucks, or to roll them up or down inclines.
NOTE.. For heavy loads it is recommended that one or two completed turns be taken
round the object with the parbuckling rope. For exceptionally heavy loads two separate
parbuckling ropes and purchases should be used, one at each end of object.
Attach one end of each part to an immoveable object. Take a round turn around the cylinder
and secure the free end to another suitable anchorage for slackening away as the load is
allowed to move away. To maintain control over heavy objects use a purchase or tackle.
When using only one parbuckle rope make sure that the load can be lowered evenly. If two
parbuckle ropes are used both must be slackened evenly.
Use parbuckle rope in the centre to start the load moving and also to act as a restrainer when
the load is rolling.
Please note:
The rope must be strong enough and long enough to do the job.
Skids or bearers must be rigidly fixed.
All persons must be kept away from both front and rear of the load.
20
21. Rolling objects
Rollers can be used where the loads are bulky or heavy, and there is no room to lift the load
into position by crane. The surfaces underneath should be level and hard. Sole planks may
be used to provide a level surface if the ground is uneven.
Types of rollers:
Steel scaffold tube for light loads.
Solid steel bar for heavy loads.
Timber rollers or logs for "bush jobs".
Timber bearers should be placed on the rollers and the load landed on bearers giving the
rollers two even surfaces. The bearers must be of sufficient thickness to clear any projections
from under the load. Alternatively, a special cradle may be used.
Use at least three rollers to ensure that the load does not become unbalanced and topple off.
Place rollers at an angle to change direction of movement.
Hands and feet must be kept clear from the rollers while the load is moving.
Skidding 108
Skidding is where the load slides into place on skids set up on rails. To skid a heavy load set
up well greased rails strong enough to support the load on sleepers.
Loosely bolted fish plates must be used to join the rails together. Each rail must be packed
above the next rail in the direction of movement.
The sliding shoes should be constructed of steel channel sections slightly turned-up on the
ends of the web and slightly turned outwards on the ends of the flange.
Timber bearers should be placed across the rails on the shoes at various positions to suit the
balance of the load. The bearers must be strong enough to support the load in the centre.
When the load is in motion care must be taken to ensure that the shoes and bearers travel
evenly.
Skids should be packed level to prevent the load from working or toppling sideways.
Where necessary, a restraining purchase should be fitted to the rear to obtain better control
of the load.
21
22. When driving steel wedges take care that follow up packing is inserted, as the wedges can
fly out.
When driving wedges keep well clear of the rear of the wedge as they fly out with extreme
force. Secure the wedge with a lanyard, especially when working at a height.
When driving more than one wedge try to synchronise the blows on each. If steel wedges are
fixed, extreme care must be taken when withdrawing them, as they fly out with great force.
Be careful of the fingers when placing or removing wedges or packings. Hold packing by the
end and keep fingers well clear.
Grind off all burrs or mushroom heads on steel wedges as they fly off and cause serious
injury.
Skates 110
Skates are a method of moving heavy loads with a set of small rollers fixed into a solid
frame which are set in bearings and run very freely. They are built to hold a specific safe
working load which should not be exceeded.
Prior to use:
Sweep clean the area in the direction of travel so that there are no obstructions to jam the
skates.
Ensure that the surface is strong enough to take the weight of the load displaced over the
small area of the skate, or skates, and that the skates will not damage the surface.
Ensure that the skates are placed under the load in a position so that there is even loading on
every skate and that the load is level. If this cannot be done bearers must be placed under the
load to ensure even loading.
22
23. Ensure that there are personnel to keep watch for the load shifting dangerously while it is
moving.
Ensure that all skates run freely and that there is no damage to them
Do not move a load on skates quickly. Use a restraining purchase at the rear to ensure that
the load does not "get away".
Skates can be reversed so that the skates remain stationary and the load runs over them.
During this procedure make sure that the load does not run off the skates and topple over.
SKIDDING OR SLIDING
When force is used to produce movement in a body some part of that force or effort is lost
by overcoming friction.
Friction is caused by surface irregularities, type of material and molecular attraction. When
bodies are at rest the frictional force is known as "Limiting Friction, when in motion the
frictional force is known as "Sliding Friction."
Lubrication and the smaller contact area reduces friction
SLIDING FRICTION
The sliding resistance between flat level surfaces depends on the type of materials in contact
with each other and their surface finish. Fine machined or polished surfaces will slide easier
than rough surface finishes.
Lubrication between the surfaces will considerably reduce friction. In theory frictional forces
are independent of area, but this is not true when the surfaces are lubricated the smaller
contact area reduces friction. Remember water is a good lubricant for large areas.
ROLLING ON A FLAT LEVEL SURFACE
Rolling Friction or Rolling Resistance is substantially less than sliding friction. The ridges
formed on the surface as it deforms under load cause rolling resistance. These are very small
on steel surfaces.
23
24. The less resistance is when the load is over a larger area as indicated above. It is necessary
for riggers to draw on their experience when calculating the effort required moving a load on
rollers. The following table shows the approximate effort required to overcome rolling
resistance on hard flat surfaces (steel or concrete).
TYPE OF ROLLER EFFORT REQUIRED TO OVERCOME
ROLLING RESISTANCE
Properly constructed trolley
(a) Steel rollers with bronze bearings 35-40 kg per tonne
(b) Steel rollers with roller bearings 15-20 kg per tonne
Shifting skates 50-70 kg per tonne
Solid steel rollers or steam pipe 70-90 kg per tonne
Example: Find the effort required to move a 5 tonne load with solid steel rollers (surface
hard and level) the table -steel rollers require an effort of 70 kg per tonne
Therefore effort = 5 x 70 = 350 kilograms
Calculate the effort required to move a load weighing 60 Tonne placed on shifting skates
that require an effort of 50 kilograms per tonne on a flat level surface
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
THE INCLINED PLANE (up the hill)
Friction
Either sliding or rolling resistance is always present when a load is moved. Therefore we can
combine our practical knowledge of the effort required to overcome sliding or rolling
resistance with the mechanical advantage of the incline plane. By adding the effort required
to move the load on a flat level surface to the effort to move the load up the ramp we will
know the total effort required. When loads are rolled up ramps properly constructed trolleys
or shifting skates should be used.
24
25. The inclined plane has numerous practical applications. When used as a ramp to raise
objects the work done may be expressed as follows:
Disregarding Friction
WORK INPUT = WORK OUTPUT
Therefore Force x length of ramp = Load x height of ramp
Force = Load x height of ramp divided by Length of ramp
Example
Calculate the effort required to move a load weighing 10 tonne up a ramp 8 metre long by
720 millimetres high. The load is placed on shifting skates that require an effort of 70 kg per
tonne to move on a flat level surface.
Total effort required = Effort to overcome rolling resistance + Effort on ramp
Effort on flat surface = Load x skate type
= 10 x 70 = 700 kgs
Effort on ramp = Load x Height of ramp
Length of ramp
= 10 x 0.72
8
= 900 kgs
Total effort required = 900 + 700 = 1600 kgs
The total effort required is equal to the minimum line pull of the winch. Therefore in this
example a two tonne winch would be required.
25
26. When you do not know the length of the ramp you use Pythagoras theorem which is A
squared + B squared = C squared i.e. we have a ramp with a 4 metre base and is 2 metres
high
4 x 4 =16 2x2=4
Therefore 16 + 4 = 20 squared = 4.5 ramp length
Calculate the slope length of the following ramps.
---------------------------------- ----------------------------- ------------------------------
---------------------------------- ----------------------------- ------------------------------
VEHICLE RECOVERY
The type of terrain the vehicle is in will vary the rolling resistance and a steep grade or slope
will increase the effort required to winch the vehicle back onto the roadway
The rolling resistance of a pneumatic tyred vehicle on a flat road is approximately 40
kilograms per tonne of vehicle weight.
The following table is a guide to calculate the rolling resistance of the vehicle on a variety of
flat surfaces:
TYPE OF SURFACE ROLLING RESISTANCE PER TONNE
Concrete or Asphalt 40 - 50 kg per tonne
Grass 120 - 140 kg per tonne
Gravel 200 kg per tonne
26
27. Soft Sand 250 kg per tonne
Shallow Mud 300 - 350 kg per tonne
Bog 500 kg per tonne
The slope or gradient may be measured in degrees or checked in the same manner as a ramp.
When the slope is measured in degrees the approximate force required to roll the vehicle up
the slope may be calculated by using 1/60th of the vehicle weight for each degree of slope.
EXAMPLE: Find the line pull for a winch used to recover a vehicle weighing 20 tonne. The
surface is gravel and the slope is 10 ' (Rclling Resistance for gravel 200 kg per tonne).
Total Effort = Effort on Flat + Effort on Slope
= (200 x 20) +(1 x 10 x 20000 kgs)
60
4000 kg + 3333 kg = 7333 kg
the winch should have an 8 tonne line pull.
NOTE: When the slope is 45' rig for the total weight of the vehicle.
FLEXIBLE STEEL WIRE ROPE
There are many different types of lays and construction of FSWR to combat fatigue and
abrasion, the two destructive forces, which occur whenever FSWR is bent over a system of
sheaves.
Wire flexes as it bends over sheaves and drums. As the wire bends over the sheave fatigue
takes place. The outer wires are stretched and the inner wires are crushed against the sheave
groove or drum.
Wire never lays straight into the groove of a sheave because the load swings slightly or the
rope vibrates. This causes friction or abrasion between the side of the sheave and the wire,
wearing the outer wires of the strands.
LAYING FSWR ONTO A DRUM
The new rope should be delivered on a spool. Set up a spool so that the rope runs from the
top of the spool to the top of the drum, or from the bottom of the spool to the bottom of the
drum.
27
28. If a new rope is delivered in a coil, a turntable should be rigged up to run the rope onto the
drum. A coil of rope must not be laid on the ground and wound straight onto the drum
otherwise there will be severe twisting and kinking of the rope.
Do not take rope off one side of a reel laid flat on the ground as a loop because a kink may
be produced from each wrap of the rope taken.
The whole cross section of the rope must be held solid when bolting or securing hoist or luff
ropes to winch drum anchorages. If a rope is not completely secured the inner strands can
pull out leaving only the outer strands secured at the anchorage.
The bottom layers on multiple layered drums must be laid on correctly. If they are not, the
lead rope will jam in between lower layers under a heavy load causing condemnable defects
in a new rope.
When laying the rope onto an un-grooved drum, use a mallet or a piece of timber (to prevent
damage to FSWR) to tap the turns together as they wind onto the drum to ensure that there
are no gaps between the lays.
MANUAL UNCOILING
If it is not possible to remove the rope from the reel by using jacks, stands, a turntable or by
rolling the reel use the following procedure:
With the reel resting on its flanges, unwind several wraps of rope to accumulate sufficient
slack.
28
29. Back-up the rope to make a loose loop on the spool, slip one loop off the right flange and lay
this loop on the floor.
Slip a similar loop off the left flange and also lie it on the floor. The rope on the floor will
then be in the form of a figure eight.
Repeat this procedure first on the right, then on the left, until the required length has been
unreeled.
Roll the reel back off the accumulation of rope on the floor, and pull away the end of the
rope. Watch out for any loops thrown out to prevent kinking.
Where the same situation exists with a coil of rope (eg where there is no turntable), the coil
should be stood on edge and unrolled as previously described.
If as a last resort the rope must be laid on the ground and uncoiled, extra precautions must be
taken to prevent kinking:
The coil should be laid down so that the outside end of the rope finishes or spirals clockwise
for right hand lay or anti-clockwise for left hand lay.
The stops or ties securing the coil may then be removed and the outside end carried along in
a straight line, allowing the rope to revolve in the hands as the turns or loops are lifted
carefully from the coil by another person and thrown or straightened out immediately as the
rope is stretched along.
Rope that has been coiled with under turns by an experienced rigger will pull away without
kinking.
At all times care should be taken to prevent wire rope from running in sand, ashes, clinker,
earth, mud and so on.
29
30. SPLICING A GUIDE TO RIGGING Page 23
EYE SPLICE IN WIRE ROPE.
Bend the rope round a pear-shaped thimble two feet or more from the end. For this purpose,
a vice, preferably a rigger's vice, is essential. Whip the strands, if the wire is not pre-formed,
and unlay them as far as the thimble. Tuck A under three strands. Tuck B under two strands,
entering between the same two strands as A. Tuck C under one strand, entering between the
same two strands as A and B (Fig. 86A). Turn the work over, replace it in the vice, and tuck
D, E and F under one strand each (Fig. 860). Tuck each strand twice more ; then taper and
tuck twice again. Each strand in Fig. 86c has been tucked twice. The strands in Fig. 86D
have been tucked three times whole, then tapered and tucked, and tapered and tucked again.
The strands in Fig. 86E have been tucked twice whole, then tapered and tucked and tapered
and tucked again. In tapering, remove about a third of the wires before each tuck.
Tucking with the lay differs from tucking against the lay, for each strand seems to be
wrapped spirally round a corresponding strand in the standing part. Except when A, B and C
are tucked for the first time, the strands should be untwisted once or twice at each tuck, in
order that they may lie flat and become one with the strands about which they ate wrapped.
When an opening is forced between the strands, the steel spike or fid should not be inserted
at the point where the tuck is desired, but some distance along the rope, away from the
thimble. In this way, the strand can be pulled through easily, and at once falls into place
when a rotating pressure is exerted on the handle of the spike. The finished splice should be
hammered into symmetry, beginning at the thimble, and working towards the standing part.
30
31. WINCHES, SHEAVES AND PURCHASES FOR FSWR
Sheaves lead the rope over the head of cranes and hoists and are used in pulley systems to
gain a mechanical advantage.
Flare angle and groove depth
The groove depth of a sheave should not be less than 1.5 times the rope diameter. However
if the rope is positively prevented from leaving the groove the minimum depth of the groove
can be equal to the rope diameter.
The sheave groove sides should have a flare angle of a minimum of 42° and a maximum of
52°.
The grooves should be slightly larger than the nominal diameter of the rope. Grooves, which
are too large, will flatten the rope. Grooves too small will pinch the rope and the extra
friction can cut it to pieces.
Sheaves should have a smooth finish with flared edges, which are rounded-off.
Sheave diameters
The table below gives sheave diameters and safety factors for types of work:
Caution. Modern cranes and hoists are complex engineering equipment, and many have
special construction luff and hoist ropes. It is essential that the sheaves, which were designed
for a particular crane or hoist, be used for that purpose.
It is also essential that when a rope is replaced, the replacement is the same diameter and
construction and that the sheave system is thoroughly checked to ensure that any damaged or
worn grooves likely to ruin the new rope are repaired or replaced.
SHEAVE BLOCK SYSTEMS
A lead sheave is a single sheave block used to change or control the direction of the hauling
part of the purchase. The first lead sheave out from the winch maintains the fleet angle and
helps to control the rope reeling onto the winch.
31
32. NOTE: Where the sheave blocks are an integral part of a crane or similar appliance they
must comply with AS 1418. Which makes provision for higher rope speeds. Larger sheave
diameters and constant duty operation.
A snatch block is a block with a gate or hinged portion through which the rope is passed to
facilitate reeving.
Load rating of a sheave block is based on the rating of the head fitting of the respective
sheave block and will be related to the number of parts of rope applied to the sheave block
and the manner of reeving. The calculated load on the head fitting or sling should not exceed
the S.W.L. of the block.
The following sketch shows the difference between a fixed and moving sheave. By attaching
a sheave to the object to be raised or moved, there is a mechanical advantage of two.
32
33. When sheaves are combined they form sheave blocks and multiple sheave blocks reeved
with either wire or fibre rope are used to gain mechanical advantage in the hoisting or
movement of loads.
ROPE TACKLE
(a) A tackle is formed by reeving rope through two blocks and is used in work for:
Lifting a load. (b) Hauling a load.
Reeving a Tackle
To 'reeve' a tackle, two men should stand back to back about 2 m apart, with the blocks
slightly in front of them between their feet and the hooks pointing outward. The coil of rope
should be to the left of the top block for lifting tackle, i.e. the three-sheave block for the 3/2
tackles. The first man should reeve the standing end of the rope through the lowest sheave of
the top block, then pass it to the second man who will reeve it through the lowest sheave of
the second block.
The rope should be passed successively through the sheaves of both blocks from left to right
and finally made fast to the becket of the second block by two half hitches. The running end
should be secured to prevent it from slipping.
Lifting RopeTackle
When calculating the capabilities of a lifting tackle it must first be realised that only the
returns between the blocks are assisting to lift the weight and that the running end is not
helping in the lifting. The power is exerted directly on it and in the opposite direction to that
in which the weight is moving. Factors to be taken into consideration in calculating the
strength of a lifting tackle are:
(a) The SWL of a rope Dia x Dia / 100 = kN. Or Dia x Dia = SWL
(b) The number of returns at the moving block (including the running end if it is made fast to
the moving block).
(c) The loss of efficiency of the tackle owing to friction. One-third reduction allowed.
Example using a 3 and a 2 tackle reeved with a 24 mm rope. (SWL of rope) x (Returns at
moving block) x 2/3 or .666 (friction loss); which is 24 x 24 / 100 x 5 x .666 = 19.2 kn =
1920 kg SWL or 24 x 24 x 5 x .666 = 1918 kg SWL
33
34. Hauling Tackle
When calculating the strength of a hauling tackle it must be remembered that the hauling
part of the fall is pulled in the same direction as the weight to be moved and assists the
returns to move the weight. The hauling part must therefore be included in the calculation
assessing the number of returns at the moving block.
All other considerations in assessing the strength of a hauling tackle are exactly the same as
for a lifting tackle.
Example using a 3 and a 2 tackle reeved with a 24 mm fibre rope.
(SWL of rope) x (Returns at moving block plus hauling part) x .666 or 2/3
Which is 24 x 24 / 100 x 6 x .666 = 23.02 kn = 2302 kg haul Or 24 x 24 x 6 x .666 = 2301
kg
The short, cut, and eye splices can be used for suspending loads or people, but cannot pass
through the sheave cheek plates. They should have at least three full tucks against the lay.
After the three full tucks the ends of the strands can be reduced and tapered and the splice
served.
However when a load is applied to the rope and the splice stretches, the serving will become
loose. It is better, stronger, and safer to dog knot half the strands with a neat seizing after
completing the splice.
Thimbles
A thimble should be spliced into the eye of the standing or becket eye of a tackle. Thimbles
are solid round, split round or pear shaped split. They are split to enable them to be opened
and fitted to the anchorage and then closed before splicing.
There should be no points on the throat of the thimble that could bite into the rope. Thimbles
should be large enough to allow the rope to seat well into the score with the rope supported
for half of its circumference without the groove edges biting into the rope. A small thimble
can cut the rope and do more damage than ordinary wear and abrasion.
Fibre rope slings
34
35. Blocks and tackles
A tackle is the term used when fibre rope is reeved around sheaves to gain a mechanical
advantage. Caution: Fibre rope tackle blocks must not be used for FSWR purchases.
Blocks
Blocks are made of wood (clump), wood and steel (internal iron bound 1IB), and steel. The
wooden clump blocks are fitted with a FSWR or fibre rope strop fitting in a score at right
angles to the sheave and steel pin. The sheaves are usually bronze or gunmetal. Some older
sheaves were made from the very hard wood, called lignum vitae.
Double sheave block
The wooden llB block has beech cheeks and partitions, with a forged eyebolt and forked
steel plates morticed into the cheeks and drilled to take a steel pin. The sheaves are usually
bronze or gunmetal and the pin is secured by a steel keeper plate over a square head.
Steel blocks are made of mild steel cheek plates secured to a yoke drilled for an eyebolt or a
forged hook. Reinforcing plates often run down outside the cheek plates to the bottom,
where they are drilled to take becket, spreader bolts and ferrules.
The sheave pin fits into holes drilled through straps, cheeks and partitions and is usually of
mild steel with a flanged end and a spigot with a cotter retainer at the other end. Lifting
hooks or eyes are the swivel type (not upset or riveted type).
Care must be taken when maintaining and inspecting to look for worn pins, sheave bushes,
insecure fastening of the hook yoke to cheeks and yoke crosshead, securing of sheave pin,
becket and pin and general soundness of the whole frame.
Types of tackles:
Gantline - A single fixed block.
Single whip - Two single blocks.
Whip upon whip - Two moveable and one fixed single block.
Luff tackle - Single and double block.
Gun tackle - Two double blocks.
Light gin tackle - or Handy billy - Double and treble blocks.
Heavy gin tackle - Two treble blocks.
45
35
36. Note:
The above masses must not exceed those marked on the blocks as being the safe mass that
may be lifted. Most blocks are limited by the size of hooks and other components and not the
number of fails of rope. A factor for friction has been added.
(1) The safe masses shown in this table are for natural fibre rope - 3 strand hawser laid.
(2) The working load limit together with any conditions of loading deemed necessary for
safe use is to be stamped or otherwise marked on each block.
(3) Sheave diameters measured at the bottom of the groove may be as follows (temporary
use only):
(a) For power operated blocks: 10 x rope diameter
(b) For hand operated blocks: 5 x rope diameter
(4) The beckets of blocks should be steel, preferably of drop forged or wrought construction.
If welded they should be to an engineered design and strongly made.
(5) The locking pins of hook nuts, where used, should be closely adjacent to the nut top
surface.
(6) Hook shank collars should not be welded without an engineered design.
(7) Snatch blocks should incorporate a locking pin of positive type not requiring the use of
any tool for its effective positioning. A drop nose pin used as a hinge pin is recommended
and the locking device must be strongly made and suitable for the intended use of the block.
(8) Fibre rope should not be less than 16 mm diameter when held under load by hand.
46
REEVING CRANES
Large capacity cranes have several parts to the main hoist fall making the main hook very
slow.
When reducing the number of parts to give a faster hook ensure that the falls are not reduced
from one side of the boom head sheaves and the main hoist block.
36
37. Otherwise rotational torque can develop on the boom head exerting side pull on the main
hoist block. When reducing parts the rope must be reeved again to ensure that there are an
equal number of parts either side of the boom head and the main hoist block.
The number of parts must be capable of supporting the load to be lifted. A fast hook must
still be a safe hook.
The greatest load on any rope in a purchase is the load in the lead rope to the winch. This is
due to the friction between the rope in the groove of the sheave and the sheave pin. Friction
is estimated at between 3% and 5% per sheave (i.e. up to one twentieth of the rope load that
would occur if there was no friction).
When a load is at rest, suspended from the lower block, the becket load (the load in each part
of the rope purchase) is found as follows:
Becket load = Total load on lower block + Number of parts of rope supporting load.
37
38. Note: The total load on the lower block includes the load to be lifted plus packing, slings,
shackles, blocks.
For example -(including frictional effects)
Total load on the lower block = 3.5 tonne gear
Number of parts of rope = 5 supporting the moving block Becket load (BL) = 3.5 / 5 = 0.7
tonne
38
39. However as lifting commences friction causes the load in the rope falls to increase by up to
10 % for each sheave the rope passes over, including lead sheaves (if any).
SHEAVE BLOCK SYSTEMS
Becket Load is equal to the static load in each part of rope supporting the lower or moving
block.
THERE FOR BECKET LOAD = TOTAL LOAD ON LOWER BLOCK
NO. OF ROPES SUPPORTING LOWER BLOCK
39
40. Total Load includes the weight of the lower block, the suspended load, slings or any other
lifting attachment.
Load in Lead Line to the winch is equal to the becket load plus the progressive load increase
in the rope due to friction. This is calculated by allowing a percentage increase in load for
each sheave in the system.
Allow 3% for each sheave fitted with bailor roller bearings. 3 devided into 1 hundred = 33
Allow 5% for each sheave fitted with bronze bearings. 5 devided into 1 hundred = 20
Allow 10% when the sheaves are worn. 10 divided into 1 hundred = 10
Note: 5% of a hundred is 20
Load in Lead Line = Becket Load + (Becket Load x 5% or 20 x Total No. sheaves)
Load on Head Fitting or Head Sling
= Total Load on Lower Block + Load in Lead Line + Lifting tackle weight
EXAMPLE:
A three and two sheave block is attached to an overhead beam by a wire rope sling to raise a
total load of 3.5 tonne. Allow for one lead sheave to the winch. All sheaves are fitted with
bronze bearings. The lifting tackle weights 70 kilograms.
(a) Calculate the load in the lead line and select the size of winch.
(b) Calculate the load in the head sling.
Becket Load = Total Load on Lower block
Number of supporting ropes
= 3500 = 700 kgs
5
Load in lead line = BL + (BL x Total No. of sheaves)
20
40
41. = 700 + (700 x 6) = 910 kgs
20
Load in head sling = Total load + Load in lead line + Tackle weight
= 3500 + 910 + 70 = 4480 kgs
PULLEY SYSTEMS
A 2 x 2 sheave system with one lead sheave is available to lift a load of 12 tonne. The lifting
slings and shackels for the load weighs .3 tonne. The Reeved Tackle Weighs 0.2 Tonne
CALCULATE:
The becket load
Load in the lead rope
What is the size of the winch required carrying out the lift.
The load in the head block sling.
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
-----------------------------------------------
PULLEY SYSTEMS
A 3 x 2 purchase with three lead sheaves is to be used to lift a load of 15 tonne. The tackle
required to lift and sling the load weighs .35 tonne.
CALCULATE:
The load on the lower block
The becket load
The load in the lead to the winch
The load in the head block sling
41
43. DRUMS
Drums are the pulling mechanism, which rotates, hauls in and stores surplus wire. The
braking mechanism is connected to either the drum or the gearing, which is joined to the
drive mechanism.
Drums are measured from the centre to the Inside of the flange. A drum, which measures 1
m from flange to flange, is therefore a 0.5 m drum.
43
44. The rope should lie neatly on the drum and not be bunched up. There should be a minimum
of two full turns on the drum at all times.
The rope must be anchored to the drum with a fixed mechanical anchorage. Be aware of the
danger of not properly tightening an anchorage. Do not rely on the frictional grip relayed by
the two turns on the drum.
Comply with the crane manufacturer's recommendation about whether drums are overwound
or under wound. If a drum is wound up incorrectly it can affect the anchorage, brake and
drive mechanism to the drum, resulting in mechanical failure.
The lay of the rope and whether the drum is overwind or under wind determine where the
rope is to be anchored.
Be especially careful when raising very heavy loads to a great height such as with long boom
mobile cranes. The amount of turns on the drum determines the drum diameter. As the
diameter increases the torque to the drive mechanism and brake increases. As a result the
higher the load is raised the faster it is raised, and the more difficult the load is to control.
Operators should ensure that the hoist brake is adjusted to take the extra torque when the
load is raised to its maximum height. A brake, which holds the load near the ground, may
fail when the load is high.
The top layer on a multi-layered drum must not be closer than two rope diameters to the top
of the flange when the drum is full.
44
45. FLEET ANGLES
The maximum fleet angle is measured from the centre of the drum to the centre of the first
diverting sheave then back to the inside flange at the middle of the drum,
The maximum fleet angle for a grooved drum is 5° and for an un-grooved drum is 3°; to
achieve these angles the distance from the drum to the first diverting sheave must be a
minimum of:
.19 times half the width of the drum for an un-grooved drum, .12 times half the width of the
drum for a grooved drum,
Example 1:
Width of the grooved drum = 1 metre 12 x 1 x 0.5 = 6
Therefore the sheave must be 6 metres from the drum.
Example 2:
Width of the ungrooved drum = 1 metre 19 x 1 x 0.5 = 9.5
Therefore the sheave must be 9.5 metres from the drum.
The width of the winch drum is 3.2 m. The winch drum is grooved.
Using the width and type of drum given, calculate the minimum distance between the lead
block and the winch drum.
---------------------------------------------------------------------------------------------------------------
----
Width of an ungrooved drum = 1 .8 Width of a grooved drum = .8
Therefore the sheave be ____ m from the drum Therefore the sheave be ____ m from
the drum
If the fleet angle is too large or the distance between the drum and the first lead or diverting
sheave is too short, the rope will not lie neatly on the drum and will create severe wear on
the rope and the sheave flange.
45
46. WINCH OPERATION
Before operating a winch at any time, the main features that should be checked?
Winch holding down bolts and anchorage generally. (Rule of thumb for counterweight is 4
times SWL)
Sliding gears, if any, and dog-clutches to be in full engagement.
See that there are no broken gear teeth, or cracked bearing caps, gears loose on shafts, and
similar defects.
The yearly service date has been stamped on service plate.
at commencement of operation the operator should observed the following.
(a) See that the rope-path is clear.
(b) See that no person may be in a position to be struck by a load, particularly if logrolling or
similar snigging is taking place where the load may over-carry.
(c) See that the rope has a fair lead on to the drum, at an angle of not more than 3° (or I in
19) for un-grooved drums or 5° (or I in 12) for grooved drums.
(d) Make shore that the FSWR is spooling on neatly, particularly on un-grooved drums. No
matter which drum, when under strain, crossed turns will damage bottom layers of rope, and
pull it between the turns of bottom layers, where the bottom layer is not spooled neatly, with
consequent damage to the rope.
(e) Whilst the rope is moving you should make shore it's path of travel is watched, to make
sure that the rope is not pulling into a crack in flooring or decking, under rails, or between
piles of logs, steel or other obstructions.
This will help to guard against sudden stalling which would damage rope, winch, or
anchorage and cause a hazard to the operator or other persons.
(f) You must at all times make shore at least 2 full turns of rope remain on the winch drum,
this is to relieve strain on the anchorage of the rope to the drum and also helps stop back
46
47. winding, which puts stress on the anchorage of the rope on the drum and causes rope and
brake failure
(g) When spooling a rope onto a drum make shore there is not too much rope for the spool as
the rope may overflow the drum, with the possibility of jamming between drum and bearing,
or be thrown into gear teeth, etc. The same could happen if the rope is spooled badly on the
drum. For this reason, and for reasons of general safety on the winch See that guards
covering gears, couplings, belts and other moving parts are always maintained in good order,
and replaced after being removed for any reason.
(h) Back hooking of the winch rope is rot recommended as a general practice. The part of the
rope used for back- hooking naturally receives most wear, and therefore should be inspected
frequently, This may be due to bad nips, either around the hook or sharp parts of the load
causing local wear or internal wear on the rope. The hook and other type of termination,
together with any thimbles, swivels, or other devices in use should be frequently checked
(i) No brakes should ever be interfered with at any time. The attachment of the
counterweighted brakes should also be frequently checked and never tied back to render it in
effective.
A friction driven winch should not be used for hoisting loads a positive drive is required for
prevention of slip-back, etc., in the event of brake failure. A winch by such means as
spragging gear teeth, etc. (Objects placed between teeth or spokes).
Where a winch is fitted with a warping drum (nigger-head) this may be used for hoisting
loads, with approved operator only. When using a nigger head do not use synthetic fibre
rope, such as nylon as the friction causes heat, which melts the rope fibres. They also have
great elasticity and stretch which is an advantage for shock load absorption, but which may
cause dangerous recoil if the rope breaks.
The requirement for a winch used to hoist or lower personnel, is an automatically applied, or
fail-safe brake system. Use particular care to ensure that the load does not gain speed, which
would make it difficult to stop, or which may damage the winch due to over speeding. This
can lead to bursting of parts such as rotor armatures, couplings and gears
BREAKING SPEED
47
48. (j) If winching over long distances out of sight such as on bridge works or the like it is
important that an efficient system of communication be available, this may be by visual
signals, telephone, loud speaker system, radio or by whistle or loud hailer between winch
driver and load area.
Warning signs or barricades or both to keep persons out of the rope path or path of the load,
and in some cases an audible warning device, such as a whistle, bell or horn. Again the
operator's view may be obstructed, so that due warning may be given to worn the public.
(k) What is the purpose of a fairlead and why is it so named?
The name aptly describes the function, which is to give a rope a fair lead on to a winding
drum, for correct spooling. Usually consists of one or more rollers, sometimes on a swivel, a
fixed guide is sometimes used.
A snatch block or other leading block may be fixed to a suitable anchorage to guide the rope
but remember snatch blocks should not be used for lifting purposes. They are designed for
easy Insertion of the rope, when hauling loads mainly in a horizontal plane, and for the sole
purpose of guiding the rope. Particular attention should be paid to their means of anchoring.
(l) On tractor or other vehicles with mounted winches, care should be taken to ensure that
the vehicle is in a stable position before hauling commences, so as not to be tipped, or
dragged sideways or on sloping ground, or unstable ground such as river banks, earth
embankments and similar hazardous locations.
When leaving a winch un-attended you should move to prevent un-authorized use,
particularly at the close of work?
(m) Where suitable, the controls should always be locked. If it is a hand winch it may be
possible to remove the handles. With an electric winch the isolating switch should be locked
in the "Off" position. With an air, hydraulic or other type, including internal or external
combustion, means should also be provided for locking off the source of power.
48
49. Can FSWR be safely used in a fibre rope tackle block?
------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
What is the minimum included angle of flare between the two sides of the groove of a
sheave in a wire rope purchase block?
------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
What type of damage is caused by sheaves where the groove is too small for the rope?
------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
What is the minimum depth of groove for a grooved winch drum?
------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
What is the minimum distance, which the flanges of a winch drum should extend above the
surface of the outer layer of rope?
------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
What is the minimum number of full turns, which must remain on a winch drum when the
load on the rope is fully lowered?
49
50. ------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
Is a person with a Basic Rigging Certificate allowed to supervise dual lifts?
---------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------
------------
Is a person with a Basic Rigging Certificate allowed to erect a swing stage or boatswain's
chair?
------------------------------------------------------------------------------------------------------------
--------- ---------------------------------------------------------------------------------------------------
------------------
Is a person with a Basic Rigging Certificate allowed to supervise demolition rigging?
------------------------------------------------------------------------------------------------------------
---------
------------------------------------------------------------------------------------------------------------
---------
-------------------------------------------- ----------------------------------------------
-------------------------------------------- ----------------------------------------------
-------------------------------------------- ----------------------------------------------
Work out the following
A 16 Tonne load is to be hauled up a ramp 12 metres long and 3 metres high. The force
required to move the load on the flat is 50 Kgs/Tonne. A 3 x 3 sheave system with one lead
sheave is to be to
assist winching.
Calculate:
(a) The slope length.
(b) The total effort required moving the load up the ramp.
The minimum winch capacity.
50
52. Size of FSWR on winch = Size of FSWR on winch =
Lead rope to winch = Lead rope to winch =
Head sling load = Head sling load =
BOLTED CONNECTIONS IN ENGINEERING STRUCTURES DESIGN OF A BOLTED
CONNECTION
The type of bolt, size and number of bolts in the joint must be chosen so that it is possible to
have sufficient total preload to withstand the external load. High strength structural bolts are
used rather than commercial bolts where higher induced tension in the joint is the main
design consideration. The Design Engineer is responsible for all connections being in
accordance with the relevant Codes and Specifications of the Engineer
The rigger. Boilermaker. Fitter or other allied tradesman on the job is responsible for the
assembly and correct tightening of the bolted connection. The Supervising Engineer or his
representative is responsible for procedure and inspection.
HIGH STRENGTH STRUCTURAL BOLTS
High strength structural bolts are manufactured to Australian Standard 1252. The three radial
lines on the top of the bolt head indicating quality and type of thread -Metric easily identify
these high strength structural bolts. The nut is heavier than a standard nut and is identified by
three lines arranged circumferentially on the face.
HOW THE BOLTED CONNECTIONS CARRY LOAD
2
53. The load that a bolted joint can carry before the mating faces of the bolted members move is
determined by the amount of preload on all bolts comprising the joint.
Induced tension in the joint is controlled by nut rotation. Regardless of the nature of the load
or type of bolts used, the bolts should be tightened correctly that is to there recommend
preload. There are no exceptions.
The Joins depends on the clamping force developed by the bolts and the transmission of load
by friction between the mating surfaces of the bolted members. It Is Important to properly
control the tightening of the nuts and the preparation of the contact surfaces.
Therefore the assembly surfaces in contact must be free of oil, dirt, loose rust, loose scale,
burrs and other defects, which would prevent solid seating of the parts or would interfere
with the development of friction between them. The surfaces are often abrasive blasted and
coated with an inorganic zinc silicate paint that has the same resistance to slipping as blast
cleaned metal. Site personnel must avoid damage to the treated surfaces during erection, i.e.
load indicator washers used the wrong way.
Each bolt shall be assembled with at least one high strength washer and where only one
washer is used it shall be placed under the rotating component (nut or bolt).
When the bolt is snug all components must be drawn into close contact and at least one full
thread should protrude through the nut. Increased bolt length is required when using load
indicator washers.
The tightening of nuts with a calibrated power or hand torque wrench is difficult to ensure
the minimum bolt tension has been achieved without constant checking and inspection.
Therefore this method is not recommended. It is important to note that the Code specifies
bolt tension not torque.
3
54. This can be achieved by tighten the nut and bolt to what they call snug tight (a person with a
podger pulling to hand tight which is about a 120 kg force). Always tighten the bolt from the
stiffest part of the joint and move towards the free edge.
When the snug tight condition has been reached, location marks are established on the bolt
and nut (usually by using a centre punch or texta). The bolts are finally tightened by a half or
three quarter turn of the nut.
INSPECTION
When drifting cannot align the bolted members or components, it will be necessary to ream
the holes. If bolts are driven into the holes they will prevent the joint compacting and restrict
the bolt preload. Always check that the joint is fully compacted. Check the match marks and
the degree of turn from the snug tight position. And when using Direct Tension Indicator
Washers check the indicator washer has been closed to the correct gap. Normally a 0.4 mm
gap except on galvanised bolts, which will be 0.25 mm gap.
STEEL ERECTION
Plan job thoroughly.
Engineer’s erection procedure must be in place (job safety analysis) JSA
Steel supplied to correspond with plan.
All Columns and trusses to be plumbed and braced.
Guys are not to pass over thoroughfares.
Packs of purlins to be spaced so overloading of trusses does not occur.
Fully bolt and tighten purlins as they are placed.
When bolting up bolts to be placed diagonally to prevent roll.
Drifts, podger and bolts to be secure in riggers belt before going aloft.
Never leave tools where they can be knocked off beams.
Safe access to be provided to and from the work face.
Do not work on wet steelwork.
Do not work of ladders they are access only.
Complete fall protection must be in place.
4
55. How are the first-placed structural members levelled and plumbed?
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
_______________
At what angle would you fix an access ladder?
__________________________________________________________________________
__________________________________________________________________________
__________
Would you sling a roof truss away from the panel points or at the panel points?
__________________________________________________________________________
__________________________________________________________________________
__________
Would you work on the open framework of a structure without fall protection?
__________________________________________________________________________
__________________________________________________________________________
__________
How are high strength washers identified?
__________________________________________________________________________
__________________________________________________________________________
__________
Why are hardened washers necessary?
__________________________________________________________________________
__________________________________________________________________________
__________
Where should the load indicator washer be placed on the bolt?
5
56. __________________________________________________________________________
__________________________________________________________________________
__________
How is bolt tension measured with direct load indicator washers?
__________________________________________________________________________
__________________________________________________________________________
__________
Are high strength structural bolts reusable?
__________________________________________________________________________
__________________________________________________________________________
__________
Can the bolthole be aligned by flame cutting? Explain your answer.
__________________________________________________________________________
__________________________________________________________________________
__________
When the bolts are being tensioned should the thread protrude through the nut?
__________________________________________________________________________
__________________________________________________________________________
__________
When assembling a steel framed building, what is the order of erection of components?
__________________________________________________________________________
__________________________________________________________________________
__________
Before attempting to lift a roof truss into position what two checks are vital?
__________________________________________________________________________
__________________________________________________________________________
__________
6
57. During erection of steel framed building what should be continually installed in case of high
winds?
__________________________________________________________________________
__________________________________________________________________________
__________
Explain your answer fully.
__________________________________________________________________________
__________________________________________________________________________
__________
What purpose do GIRTS serve?
__________________________________________________________________________
__________________________________________________________________________
__________
What are the signs of overloading on?
A chain block
__________________________________________________________________________
__________________________________________________________________________
__________
Chain puller
__________________________________________________________________________
__________________________________________________________________________
__________
Wire puller (tirfor)
__________________________________________________________________________
__________________________________________________________________________
__________
A GUIDE TO RIGGING Chapter 11 Page 113 Natural fibre ropes rely on the friction of
twisting to stop them from pulling apart. Synthetic ropes can be much thinner and yet have a
7
58. greater WLL than natural fibre rope because they do not have overlapping fibres and
because some filaments are stronger than natural fibres of the same thickness.
Each type of synthetic fibre rope is subject to different deteriorating and condemning factors.
Acids affect some while others are affected by alkalis and most are difficult to tell apart after
some use. All types have different strengths and so the WLL is not constant.
Synthetic fibre ropes have a smooth slippery surface, which can cause slip, and failure of
most bends and hitches and is not suitable for hand haulage. Prevent this with additional half
hitches or seize the tail with yarn, twine or marline.
Where splices are made, two additional (five) tucks with all of the strands are made and the
protruding strands halved and fused together to prevent the splice from drawing or pulling
out. All plain ends of rope should be whipped, to hold the strands together until the rope is
fused.
Under some conditions synthetic fibre rope can conduct electricity and therefore should not
be used as taglines near powerlines.
Nylon (Polyamide filament)
Nylon has a breaking strength 2.25 times the breaking strength of natural fibre rope. It is not
resistant to all chemicals and can be affected by linseed oil and mineral acids such as
sulphuric and muriatic acid. Alkalis have little effect.
Heat resistance is higher (250°C) than natural fibre rope, which begins to char at 150°C.
Although nylon melts or fuses with excessive heat it stops smouldering when the heat source
is removed. It can melt with the heat build up when turns are surged around warping drums.
Nylon has about four times more stretch than natural fibre ropes, which is good for shock
loads but has little value for lifting gear. It is resistant to rot and mildew.
Dacron -terylene (Polyester filament)
Dacron-terylene has twice the breaking strength of natural fibre rope and is not as elastic as
nylon. Resistance to mild acid conditions, rot, mildew, heat or flame are the same as nylon.
Exposure to alkaline conditions (eg. caustic soda) should be avoided.
Polypropylene (Laid shattered film type)
Polypropylene has about 1.6 times the breaking strength of natural fibre rope. It is unaffected
by water and will float. It is also unaffected by acids or alkalis except in a very concentrated
form. Its strength is reduced by heat (15 to 30 per cent loss of strength at 65°C).
8
59. SYNTHETIC FIBRE ROPES HAVE MANY ADVANTAGES OVER NATURAL FIBRE
ROPES INCLUDING:
Greater strength size for size.
Lighter weight size for size.
Greater elasticity or stretch
Greater shock absorption because of greater elasticity.
Greater resistance to rot and mildew.
Better resistance to abrasion
Some are resistant to acids, others to alkalis.
Greater flexibility, ease of handling
Less water absorption.
CONDITIONS AND TOOLS FOR INSPECTING ROPE PROPERLY:
The whole length of synthetic fibre ropes should be inspected for signs of defects that may
make the rope fail and therefore condemn the rope. Manufacturers' information and advice
on inspection should be followed.
A 300 mm length of rope for comparison that was cut from the end of the line at the time of
purchase. Enough room to handle the whole length of the line systematically. A good light.
A magnifying glass may be of assistance.
The entire length of the rope must be inspected at intervals of not more than 300 mm. The
rope strands should be unlaid slightly to inspect the inside. Care should be taken to return
them to their normal position after inspection.
WHAT TO LOOK FOR:
External wear due to dragging over rough surfaces, which causes a general reduction of the
cross-section of the strands.
Local abrasion as distinct from general wears. It may be caused by the passage of the rope
over sharp edges while under tension and may cause serious loss of strength and damage.
Local rupturing or loosening of the yarns or strands may indicate them.
Internal wear caused by repeated flexing of the rope particularly when wet, and by particles
of grit picked up. It is indicated by excessive looseness in the strands and yarns.
Heavy loading may result in permanent stretching so that the extension available in an
emergency is reduced. If the original length of the line is known. Measurement of the
9
