Dual Span Clips:
Dimension A: spring force is not a significant source of wear. Dimensions B and C: spring force is a significant source of wear. The 10249111 springs cause significantly more wear than the other springs tested.
Triple Span Clips:
Dimension A and C: spring force is not a significant source of wear. Dimension B: spring force is a significant source of wear. The 10249111 spring performs better overall than the 10249241 spring currently in production.
The heavier 10249111 spring improves performance of both dual and triple span clips compared to the lighter springs, though the improvement is more significant for dual span clips. Wear decreases clip performance
ICT role in 21st century education and its challenges
Led radial insertion machine chain clip test report
1. Chain Clip Wear Test Report
Introduction
The purpose of this experiment was to determine the wear on three critical to function chain clip
dimensions due to three springs of equal free length and different spring constants, and also to analyze the
wear effects on functionality. Both dual span and small triple span configurations were included in the test.
Thirty dispense heads on the Radial 6380A sustaining machine were modified and used for the test. Each
clip was run for 50,000 cycles. Due to the variation in clamping force of the five different configurations
tested, some test heads had components replaced more frequently than others, resulting in some test clips
seeing more new components than others. The ANOVA analysis (Appendix 2, page 7) shows however that
the number of new components presented to the test clips was not statistically significant and therefore not
a significant contributor to wear.
Below is an outline of the five configurations tested:
!
Two chain clip issues drove this experiment: components migrating up and/or down in the clip and concern
that heavier springs will accelerate wear.
Upon completion of the test, force and distance measurements were taken using a test fixture and a 2.5mm
setup tool.
Setup and Data Collection
Wear Data: See Appendix 1
Dimensions A,B and C were identified as critical to function (see Appendix 3 for detail). 2.5mm,
steel, .021 in. square, .030 diagonal leaded LED’s were used for the test. These LED’s have an average
distance between leads of .0743 in. (See illustration on page 2)
Dual Span Clips:
The clip housing “tooth”, dimension C, is .074 +/-.002 in. Therefore, wear was not observed on the sides of
the tooth, but was observed on the corner radii. On the dual clip, a 2.5mm component is engaged by two
clamps: the left lead by the full clamp on the left and the right lead by the half clamp on the right.
Triple Span Clips:
Due to the dimensioning scheme of the triple span clip, dimension C is not tooth width, but distance to the
side of the tooth as shown, .038 +/-. 003 in. As in the case of the dual span clip, wear was observed on the
corner radii. This is a reasonable result since the tooth width is .062 +. 000/-. 005 in. and the average
distance between component leads was .0743 in. On the triple clip, a 2.5mm component is engaged only by
the left clamp: the left lead by the full clamp and the right lead by the half clamp.
Force and Distance Measurements: See Appendix 2
Appendix 2 shows comparison graphs of unused (unworn) clips versus tested (worn) clips and the
effect of wear on performance. The clip measurements were taken using a 2.5mm setup tool since 2.5mm
components were used for the wear test.
Chain Clip Type
Spring #1
10249225
Spring #2
10249241
Spring #3
10249111
2.5mm
Comp
Dual:42804703 x LED
Dual:42804703 x LED
Dual:42804703 x LED
Triple:90055421 N/A x LED
Triple:90055421 N/A x LED
Chain Clip Test Report.doc 06/19/01 !1
2. Summary
Assumption: 2.5mm component used for test is a suitable representative to determine chain clip wear.
Dual Span Clips:
Dimension A: spring force is not a significant source of wear.
Dim B and C: spring force is a significant source of wear.
(See Appendix 1 for supporting ANOVA analysis)
Backward ‘force to release’ performance degrades significantly for the dual span test clips with the
10249111 springs. The 10249241 spring performs more consistently between the unworn and worn chain
clips.
Distance to release was the same for unworn and test (worn) clips.
Radial 6380A dual span chain clips use the 10249225 spring.
Radial 6380B “XT” dual span chain clips use the 10249241 spring.
Triple Span Clips:
Dimension A and C: spring force is not a significant source of wear.
Dimension B: spring force is a significant source of wear.
(See Appendix 1 for supporting ANOVA analysis)
Forward ‘force to release’ and forward’.050” lean force’ performance is poor for both worn and unworn
clips, although the clips with the 10249111 spring performe slightly better in these two categories than the
10249241 spring.
The heavier 10249111 spring performs better overall than the current production 10249241 spring.
Distance to release was the same for unworn and test (worn) clips.
Radial 6380A triple span chain clips use the 10249241 spring.
Radial 6380B “XT” triple span chain clips use the 10249111 spring.
.030 in
.021 in.
.0743 in. avg
Chain Clip Test Report.doc 06/19/01 !2
3. The illustration below shows the setup for a .050” forward lean. The backward .050” lean measurements
were set up with the same gap between the test fixture attachment, mounted behind the tool, and the 2.5mm
setup tool. The force measurement was taken at the point where the 2.5mm tool touched the test fixture
attachment, which was approximately the same height as the tool in the clip.
050 in. forward lean
The ‘force to release’ force measurements were taken at the point where the 2.5mm setup tool disengaged
from the chain clip clamps with at least one lead.
Conclusion
The data presented here leads to the following conclusions:
1. Overall, a higher spring constant results in improved holding ability in both the worn and unworn
clips. However, it is nit clear whether wear at 50,000 cycles significantly decreases clip performance.
Further testing would be required to determine at what point performance begins to decline.
Chain Clip Test Report.doc 06/19/01 !3
2.5mm setup
tool
Test fixture
attachment
2.5mm setup
tool
Chain clip fastened
to test fixture
4. 2. The performance of the triple span clip improves with the heavier 10249111 spring, although it is not
as dramatic an improvement as the dual span clip with the heavier spring.
Appendix 1
MINITAB ANALYSIS OF WORN CLIP DATA
Descriptive Statistics: DIM A, DIM B, DIM C
Variable N Mean Median TrMean StDev SE Mean
DIM A 30 2.323 1.900 2.200 1.600 0.292
DIM B 30 2.413 2.300 2.335 1.456 0.266
DIM C 30 0.583 0.200 0.504 1.431 0.261
Variable Minimum Maximum Q1 Q3
DIM A 0.000 7.000 1.375 3.300
DIM B 0.000 6.100 1.400 3.250
DIM C -1.700 4.400 -0.425 1.325
The means above reflect 1000 times the change in dimension value.
*Note: Dimension C should increase with wear, not decrease (see clip housing
prints at end of report). Data may be suspect due to the measurement equipment
and/or the operator of the equipment.
Chain Clip Test Report.doc 06/19/01 !4
Average Dimension Changes: Worn Clips
%ChangeinDimension
-4.0
0.0
4.0
8.0
12.0
16.0
Clip Configuration
D
ual#1
D
ual#2
D
ual#3
Triple
#2
Triple
#3
Dimension A
Dimension B
Dimension C
5. One-way ANOVA: DIM A versus NUM COMPONENTS
Analysis of Variance for DIM A
Source DF SS MS F P
NUM COMP 2 2.73 1.36 0.52 0.603
Error 27 71.47 2.65
Total 29 74.19
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev -------+---------+---------+---------
5 20 2.420 1.876 (-----*-----)
10 4 2.700 1.140 (-------------*------------)
15 6 1.750 0.373 (-----------*----------)
-------+---------+---------+---------
Pooled StDev = 1.627 1.2 2.4 3.6
>> P-value greater than .05: Number of new components presented to clip is not significant
One-way ANOVA: DIM B versus NUM COMPONENTS
Analysis of Variance for DIM B
Source DF SS MS F P
NUM COMP 2 7.95 3.97 2.00 0.155
Error 27 53.57 1.98
Total 29 61.51
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev -------+---------+---------+---------
5 20 2.220 1.539 (-----*----)
10 4 1.875 0.826 (-----------*-----------)
15 6 3.417 1.141 (--------*---------)
-------+---------+---------+---------
Pooled StDev = 1.409 1.2 2.4 3.6
>> P-value greater than .05: Number of new components presented to clip is not significant
One-way ANOVA: DIM C versus NUM COMPONENTS
Analysis of Variance for DIM C
Source DF SS MS F P
NUM COMP 2 0.56 0.28 0.13 0.880
Error 27 58.86 2.18
Total 29 59.42
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev ----------+---------+---------+------
5 20 0.635 1.592 (-----*------)
10 4 0.725 1.825 (--------------*--------------)
15 6 0.317 0.382 (-----------*------------)
----------+---------+---------+------
Pooled StDev = 1.476 0.0 1.0 2.0
>> P-value greater than .05: Number of new components presented to clip is not significant
Descriptive Statistics: COMP SPAN
Variable N Mean Median TrMean StDev SE Mean
COMP SPA 21 74.290 74.400 74.237 1.025 0.224
Variable Minimum Maximum Q1 Q3
COMP SPA 72.300 77.300 73.750 74.700
Chain Clip Test Report.doc 06/19/01 !5
6. One-way ANOVA: DIM A: Dual Span Clip vs. Spring
Analysis of Variance for DIM A_1
Source DF SS MS F P
SPRING_1 2 0.01 0.00 0.00 0.997
Error 15 18.40 1.23
Total 17 18.41
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev --------+---------+---------+--------
1 6 1.717 1.025 (---------------*---------------)
2 6 1.700 1.579 (---------------*---------------)
3 6 1.750 0.373 (---------------*---------------)
--------+---------+---------+--------
Pooled StDev = 1.108 1.20 1.80 2.40
>> P-value greater than .05: Spring type is not significant to change in Dim A
One-way ANOVA: DIM B: Dual Span Clip vs. Spring
Analysis of Variance for DIM B_1
Source DF SS MS F P
SPRING_1 2 12.91 6.45 4.98 0.022
Error 15 19.42 1.29
Total 17 32.33
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev ------+---------+---------+---------+
1 6 1.550 1.111 (-------*-------)
2 6 1.700 1.161 (-------*-------)
3 6 3.417 1.141 (-------*--------)
------+---------+---------+---------+
Pooled StDev = 1.138 1.2 2.4 3.6 4.8
>> P-value less than .05: Spring type is significant to change in Dim B
One-way ANOVA: DIM C: Dual Span Clip vs. Spring
Analysis of Variance for DIM C_1
Source DF SS MS F P
SPRING_1 2 3.274 1.637 4.57 0.028
Error 15 5.368 0.358
Total 17 8.643
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev -+---------+---------+---------+-----
1 6 -0.7000 0.5329 (-------*--------)
2 6 -0.4000 0.8025 (-------*--------)
3 6 0.3167 0.3817 (-------*--------)
-+---------+---------+---------+-----
Pooled StDev = 0.5982 -1.20 -0.60 0.00 0.60
>> P-value less than .05: Spring type is significant to change in Dim C
One-way ANOVA: DIM A: Triple Span Clip vs. Spring
Analysis of Variance for DIM A_2
Source DF SS MS F P
SPRING_2 1 6.90 6.90 2.12 0.176
Error 10 32.62 3.26
Total 11 39.52
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev -----+---------+---------+---------+-
2.5-2 6 2.467 1.338 (----------*----------)
2.5-3 6 3.983 2.176 (----------*----------)
-----+---------+---------+---------+-
Pooled StDev = 1.806 1.5 3.0 4.5 6.0
>> P-value greater than .05: Spring type is not significant to change in Dim A
One-way ANOVA: DIM B: Triple Span vs. Spring
Analysis of Variance for DIM B_2
Chain Clip Test Report.doc 06/19/01 !6
7. Source DF SS MS F P
SPRING_2 1 10.08 10.08 5.78 0.037
Error 10 17.46 1.75
Total 11 27.54
Individual 95% CIs For Mean
Based on Pooled StDev
Level N Mean StDev ------+---------+---------+---------+
2.5-2 6 3.617 1.680 (---------*---------)
2.5-3 6 1.783 0.818 (---------*---------)
------+---------+---------+---------+
Pooled StDev = 1.321 1.2 2.4 3.6 4.8
>> P-value less than .05: Spring type is significant to change in Dim B
One-way ANOVA: DIM C:Triple Span vs. Spring
Analysis of Variance for DIM C_2
Source DF SS MS F P
SPRING_2 1 0.85 0.85 0.48 0.505
Error 10 17.84 1.78
Total 11 18.69
Individual 95% Cis For Mean
Based on Pooled StDev
Level N Mean StDev -------+---------+---------+---------
2.5-2 6 1.583 1.150 (-----------*-----------)
2.5-3 6 2.117 1.499 (-----------*-----------)
-------+---------+---------+---------
Pooled StDev = 1.336 1.0 2.0 3.0
>> P-value greater than .05: Spring type is not significant to change in Dim C
Appendix 2
Chain Clip Test Report.doc 06/19/01 !7
8. Chain Clip Test Report.doc 06/19/01 !8
Force to Release: Back
0
5
10
15
20
25
30
35
40
45
10249225 10249241 10249111
Spring
Force(gms)
0 K Dual Span
0 K Triple Span
50 K Dual Span
50 K Triple Span
Force to Release: Forward
0
5
10
15
20
25
30
35
40
45
10249225 10249241 10249111
Spring
Force(gms)
0 K Dual Span
0 K Triple Span
50 K Dual Span
50 K Triple Span
9. Appendix
Chain Clip Test Report.doc 06/19/01 !9
.050" Lean Force: Back
Force(gms)
0
11
23
34
45
Spring
1.02492e+07 1.02492e+07 1.02491e+07
0 K Dual Span
0 K Triple Span
50 K Dual Span
50 K Triple Span
.050" Lean Force: Forward
Force(gms)
0
11
23
34
45
Spring
1.02492e+07 1.02492e+07 1.02491e+07
0 K Dual Span
0 K Triple Span
50 K Dual Span
50 K Triple Span
10. Dual Span Chain Clip Housing: P/N 42717602 of Assembly 42804703
Triple Span Clip Housing: P/N 90055417 of Assembly 90055421
Chain Clip Test Report.doc 06/19/01 !10
Dim A
Dim B
Dim C
Dim C