Тестер оптических и проводных транспортных сетей Anritsu Mt1000a

Network Master™ Series
MT1000A
Network Master Pro
ниверс льный измерительный тестер тр нспортных сетей
MU100010A
естовый модуль 10G
Техническое описание
Государственный реестр средств измерений
» www.radar1.ru«

2 Product Brochure l MT1000A
MT1000A Network Master Pro представляет собой первый компактный
универсальный анализатор для тестирования OTN, позволяющий
пользователю тестировать сеть с помощью клиентских сигналов
Ethernet и SDH/SONET. Эта функция станет все более востребованной с
расширением OTN и распространением коммутации OTN.
Используя MT1000A, сочетающий тестирование OTN с тестированием
Ethernet, SDH/SONET и PDH/DSn в одном автономном приборе,
полевой технический специалист будет лучше, чем когда-либо прежде,
оснащен для того, чтобы самостоятельно разрешить проблемы,
возникающие в транспортной сети, без обращения к удаленному
центру управления сетью.
«Объем трафика, передающийся по линиям OTN, постоянно растет;
в системе OTN трафик передается в виде сигналов Ethernet или
SDH/SONET. В некоторых случаях используется даже Fibre
Channel», — говорит Джонатан Боррилл (Jonathan Borrill), директор
по маркетингу компании Anritsu (EMEA). «Поэтому полевым
техническим специалистам, развертывающим и сопровождающим
транспортные сети, важно иметь универсальный инструмент
наподобие MT1000A Network Master Pro, чтобы тестировать все
технологии, поддерживаемые в сетях, с которыми они работают».

Другие ключевые функции MT1000A Network Master Pro:
• Простой и интуитивно понятный пользовательский
интерфейс
• Поддержка подключения WLAN/Bluetooth/LAN
• Создание отчетов в формате PDF и XML для
документирования результатов тестирования
• Дистанционная работа
• Дистанционное управление (с помощью сценариев)
• Компактная и легкая конструкция для обеспечения
портативности в полевых условиях
• Работа от аккумуляторов

Redefining Transport Testing
Today’s communication networks are becoming more and
more sophisticated as leading network operators install new
technologies like OTN, MPLS-TP and Ethernet in their
metro and backhaul networks. In some cases, operators
must also support Fibre Channel links, while still keeping
legacy technologies like PDH/DSn, and SDH/SONET
operational. The Network Master Pro MT1000A redefines
the direction of future test platforms by bringing these
network test requirements to a portable device, making it
the ideal tool for field testing.

• All-in-one transport tester
– supports 1.5 Mbps to 10 Gbps
• Easy and intuitive GUI
• Dual port at all rates
•WLAN*1/Bluetooth/LAN connectivity
• PDF and XML report generation for
documenting test results
• Remote operation
• Remote control (scripting)
• Compact, lightweight design
for maximum field portability
• High performance in small form factor
• Modular platform ensuring maximum
return on investment
Metro and Core Network
Installation and Maintenance
• OTN up to OTU2 including mapping of Ethernet, Fibre
Channel*2, SDH/SONET client signals, multistage
mapping and FEC (ForwardErrorCorrection)
•Testing and verification of new OTN functions: ODU0
and ODUflex
Carrier Class Ethernet Installation
andTroubleshooting
• Ethernet testing up to 10 GigE including RFC 2544
andY.1564
• Ethernet OAM up to 10 GigE
• MPLS-TP and PBB/PBB-TE up to 10 Gbps
• IP Channel Statistics*2 up to 10 GigE
• Frame capture*2 for advanced troubleshooting
Mobile Backhaul Installation andVerification
• Synchronous Ethernet testing up to 10 GigE (G.826x
and IEEE 1588 v2)
Powerful Storage Area Networking (SAN)
Testing*2
• Fibre Channel up to 10 Gbps
Quick and EasyTesting of SDH/SONET
/PDH/DSn Networks
• SDH/SONET up to STM-64/OC-192
• PDH/DSn (E1, E3, E4, DS1, DS3)
Key Applications
All
-in-one
Easy
-to-use
OTN
full
mapping
Product Brochure l MT1000A 5
∗1: Available for certified countries and regions
including USA, Canada, Japan and all EU countries.
Please contact Anritsu for updated information.
∗2: Coming soon

The compact, battery-powered and easy-to-use Anritsu MT1000A with 10G Multirate Module MU100010A has everything in a
single, handy tester needed to install and maintain communication networks from 1.5 Mbps to 10 Gbps.
This portable, compact, lightweight instrument makes network field testing easy. Service engineers can read and interpret data
from the tested network directly on the 9-inch color display with easy-to-understand indications and graphical symbols. And the
GUI makes it simple to configure and operate the instrument at its full potential. The MT1000A has been designed for easy
expandability, reducing initial costs, and facilitating step-by-step customized investment.
All-in-One
The MT1000A has everything you need to install and maintain
communications networks from 1.5 Mbps to 10 Gbps in a single,
handy unit. It supports new technologies like OTN, Ethernet,
MPLS-TP and Fibre Channel, together with legacy SDH/SONET
and PDH/DSn technologies.
OTN Testing with Client Signals
With the MT1000A you get a powerful and complete tool set for
testing OTN signals. You can test all the way to the mapped
Ethernet, Fibre Channel and SDH/SONET client signals for quick
troubleshooting and testing of in-service OTN systems.
Easy-to-Use GUI
The user interface is optimized for troubleshooting by field
technicians and to reduce training time. It has a logical structure and
self-explanatory graphical symbols. Tests are started by launching
an intuitive application, and main results are displayed as GO/NO-GO
indications. User-programmed application favorites including all
required test parameters make operation fast and easy.
Simultaneous Testing and In-band Monitoring with Dual Port
Configuring the MT1000A with two ports at all supported rates
reduces test times by completing independent tests simultaneously
on two lines using a single tester. Or separate measurement test
applications can be run independently at the same time.
Support for dual ports is also important at analysis of in-service lines
when analyzing the performance of both directions of a line
simultaneously.
9-inch Touch Screen for Easy Viewing and Operation
The large 9-inch, high-resolution, full color, touch screen is perfect
for viewing results. And the touch screen makes instrument
operations easy.
Fast Measurement Overview
The Measurement Summary function allows a rapid overview of
measurements using GO/NO GO indications with user-defined
thresholds. Statistical histograms facilitate error tracking over time.
Flexible Connectivity
WLAN, Bluetooth and LAN connectivity ensure quick and simple
tester access in any situation. While remote operation allows an
experienced engineer to assist colleagues in the field.
Report Generation
The powerful and flexible report generator creates PDF or XML
files for selected measurements to output results in a professional
format.
Remote Operation and Control
Remote operation from a distance is simple using the Remote
Operation function, allowing operation as if on-site. The remote
scripting function cuts the manual operation time, eliminating
human testing errors.
Portable
The high portability and robustness of the MT1000A ensure quick
location of faults wherever you are. This light, small instrument is
just a fraction larger than its 9-inch screen, offering easy access in
the tightest locations. The small size coupled with large GUI makes
it easy to quickly configure, locate, solve, and report on network
issues.
Long Battery Life
Since AC power is not always available when needed, the
MT1000A tester runs for up to 3 hours on a single charge,
depending on configuration and setup. Coupled with an optional car
cigarette lighter cord, the instrument is always ready whenever and
wherever you are.

Connector Panel Overview
1 Port 1, Tx Bantam (DS1)
2 Port 1, Tx BNC (E1, E3, E4, DS3, STM-1e, STS-3)
3 Port 1, Rx Bantam (DS1)
4 Port 1, Rx BNC (E1, E3, E4, DS3, STM-1e, STS-3)
5 Port 2, Tx Bantam (DS1)
6 Port 2, Tx BNC (E1, E3, E4, DS3, STM-1e, STS-3)
7 Port 2, Rx Bantam (DS1)
8 Port 2, Rx BNC (E1, E3, E4, DS3, STM-1e, STS-3)
9 Port 1, Tx/Rx RJ48 (E1 balanced)
10 Port 2, Tx/Rx RJ48 (E1 balanced)
11 Port 1, Tx/Rx SFP+ (OTN, Ethernet, Fibre Channel, SDH/SONET optical)
12 Port 2, Tx/Rx SFP+ (OTN, Ethernet, Fibre Channel, SDH/SONET optical)
13 Port 1, Tx/Rx RJ45 (Ethernet electrical)
14 Port 2, Tx/Rx RJ45 (Ethernet electrical)
15 Audio
16 AUX
17 Clock Input
18 USB Mini-B
19 USB A
20 USB A
21 Ethernet Service Interface
22 DC Input (18 Vdc)
MT1000A has a rechargeable and replaceable
Li-ion battery.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
15 16 17 18 19 20 21 22
MT1000A is just a fraction larger than its 9-inch screen.
9-inch active TFT display and touch screen
Power switch
Speaker

Comprehensive OTN Testing for Metro and Core Network Installation and
Maintenance
OTN carries client signals, but current OTN field testers only support OTN testing at the OTN line rate with bulk test signals. This means that
problems in the carried client signals are invisible when testing an in-service OTN system.
Using the MT1000A, OTN lines can be tested at the client signal level with signals like Ethernet, Fibre Channel and SDH/SONET, because the
OTN mapping function is mandatory for modern OTN transponders. The MT1000A can also test OTN lines at the line rate with bulk signals.
The user can identify problems at all levels in the OTN signal, solving OTN issues efficiently, reducing system downtime, and reducing
operating expenses for network operators.
Testing Ethernet, Fibre Channel, or SDH/SONET Client
Signals Mapped onto OTN Signal
(Part of ODU Multiplexing Option)
The MT1000A tests OTN links carrying Ethernet or SDH/SONET
client signals, allowing the operator to test embedded client signals.
For example, an RFC 2544 or Y.1564 test can be performed with
an Ethernet signal carried over the OTN signal, allowing the service
engineer to run tests emulating the real-world requirements of end
users.
Out-of-service OTN Error and Alarm Statistics
The MT1000A supports powerful statistical measurements for BER
tests as well as OTN level alarms and errors for installing/
commissioning and troubleshooting out-of-service OTN lines.
G.8201 or M.2401 error-performance parameters are calculated
during measurement. Stress testing of network elements is
supported by inserting errors and alarms, and adjusting overhead
bytes in the signal transmitted by the instrument.
Looping-back test signal from MT1000A at far end supports easy OTN line quality tests
OTN Testing with Client Signals
The MT1000A is a powerful and full toolset for testing OTN signals. It supports complete Bit Error Rate (BER) tests with bulk signals at the
OTN level as well as tests all the way to the Ethernet, Fibre Channel and SDH/SONET client signals mapped onto the OTN signal.
OTN tests features include:
• OTU1, OTU2, OTU1e, OTU2e, OTU1f, OTU2f tests
• ODU0, ODUflex, ODU1 and ODU2 including ODU0 to ODU2 multistage mapping
• OTN tests with bulk signals at OTN level
• Comprehensive OTN error and alarm statistics
• OTN error performance measurement in accordance with G.8201 or M.2401
• ITU-T O.182-compliant FEC test
• Test of Ethernet, Fibre Channel or SDH/SONET client signals mapped onto OTN signal
• Delay measurement
• OTN header edit and capture
• OTN TCM monitoring and generation
• Service disruption analysis using APS application
• OTN tributary scan
• Full flexibility to monitor insert/overwrite client overhead and payload within OTN signal

ODUflex Test (with ODU Flex Option)
ODUflex is a new feature of OTN supporting flexible allocation of
client-signal bandwidth to make best use of OTN capacity.
The MT1000A with ODU Flex option supports ODUflex tests,
allowing operators to verify this new technology on their networks.
ITU-T O.182-compliant FEC Test
Anritsu proposed the FEC error performance tests using Poisson-
distributed random errors adopted by ITU-T Recommendation
O.182.
This method supports reproducible and accurate FEC error
correction tests by generating truly random signal errors.
High-speed networks cannot be tested accurately without using the
ITU-T O.182 Poisson error distribution.
ODU Flex Option divides capacity of ODU2 into 8 1.25G
ODUflex time slots.
In the above example, an FC-400 (4GFC) Fibre Channel signal
occupies 4 ODUflex time slots.
OTN Tributary Scan
The tributary scan feature supports quick inspection of the OTN
signal by examining it for major problems and highlighting them in
an easy-to-understand manner.
FC-400
(4GFC)
OTN Statistics Summary
OTU Alarms and Errors View
OTU Level Statistics
OTU Header Capture

Carrier Ethernet Installation and Troubleshooting
Ethernet technology is used by many applications today, including Carrier Class Ethernet, VLAN, Q-in-Q, Ethernet OAM and MPLS and,
recently, PBB-TE and MPLS-TP. Network operators must handle all these technologies, leading to long and complex test procedures.
The MT1000A with Ethernet option is a comprehensive solution for easy testing, installing, and troubleshooting Ethernet lines up to 10 Gbps
using functions for verifying bandwidth, and testing connectivity, Quality of Service (QoS), and service availability, cutting additional truck rolls,
tech support calls, and customer churn to improve operating expenses.
Ethernet test features include:
• Ethernet tests at 10 Gbps, 1 Gbps, 100 Mbps and 10 Mbps
• Traffic generation up to full line rate
• Support for IPv4 and IPv6
• Ethernet Service Activation Test (Y.1564)
• Automated RFC 2544 tests of Throughput, Frame Loss, Latency or Packet Jitter, Burstability
• BER tests – include Frame Loss and Sequence Error tests
• Service disruption measurements
• Comprehensive statistics
• Filters – to extract relevant parts of traffic
• Thresholds – to highlight abnormalities
• Simultaneous monitoring in both line directions
• IP Channel Statistics* to identify error streams, top talkers, network attacks
• Ethernet OAM tests
• 10G WAN PHY tests*
• Synchronous Ethernet test (G.826x and IEEE 1588 v2)
• Ethernet Multistream
• Stacked VLAN (Q-in-Q)
• MPLS tests
• MPLS-TP and PBB/PBB-TE tests
• Ping
• Traceroute
• Frame capture for protocol analysis with Wireshark*
• Electrical cable tests and optical signal level displays
*: Coming soon
Single-end test using MT1000A as Ethernet reflector
Ethernet Statistics
Ethernet BER Tests Statistics Summary Ethernet BER Tests Results
Wireshark®
is registered trademarks of the Wireshark Foundation.

Ethernet Service Activation Test (Y.1564)
With the ability to simultaneously test multiple traffic streams, ITU-T
Y.1564 is a new test methodology when deploying Ethernet
networks. Today's common RFC 2544 standard completes tests
one at the time and does not run all traffic streams simultaneously.
ITU-T Y.1564 has the following two test phases.
• Service Configuration Test:
This section is completed quickly, within seconds per stream.
It confirms the end-to-end configuration while quickly checking the
Information Rate (IR), Frame Transfer Delay (FTD), Frame Delay
Variation (FDV), Frame Loss Ratio (FLR), Committed Burst Size
(CBS) and Excess Burst Size (EBS) sequentially for all configured
traffic streams.
• Service Performance Test:
This section is completed based on the M.2110 standard for 15
minutes, 2 hours, 24 hours, or a user-selectable period.
It transmits all configured traffic streams simultaneously at the
CIR, confirming that all traffic can traverse the network under full
load while checking IR, FTD, FDV, FLR and Availability (AVAIL).
Simultaneous testing in the Service Performance Test section
greatly reduces the total test time compared to RFC 2544.
The MT1000A Ethernet Service Activation Test application
supports user tests in accordance with Y.1564 for up to 8 services.
Testing is typically performed with two testers running the Service
Activation Test in a local–remote setup. However, it can be run
using one tester and a far-end loopback device.
Running the Service Activation Test in a local–remote configuration
with two MT1000A testers supports control from the local
instrument. Relevant data is transferred to the remote and results
from both testers are displayed on the local instrument after the test
is completed. Easy-to-understand graphics show passed and failed
tests. When further analysis is required, the display can be
expanded to show all test details. For measurements of Frame
Transfer Delay (FTD) between two MT1000A testers, the GPS
option provides synchronization for true one-way FTD
measurement.
Running Service Activation Test in local
– remote configuration using two MT1000A testers
Y.1564 Service Configuration Test
Y.1564 Service Performance Test

RFC 2544 Test
RFC 2544 testing of Throughput, Frame Loss, Latency, Packet
Jitter and Burstability is straightforward with the MT1000A.
It automates the procedure while still allowing thorough test
configuration. For full information on performance at both line sides,
the end-to-end test mode allows two MT1000A testers to work
together in a local–remote configuration where the user controls
both testers and reads results from both locally.
IP Channel Statistics – Multiflow Counters
Up to 230 flows can be selected and filtered by MAC and IP
Source/Destination addresses, VLAN and MPLS to monitor
selected streams and display detailed information. This allows the
user to identify error streams, top talkers, and network attacks, as
well as troubleshoot network issues more deeply.
Pass-through Mode
Configuring the MT1000A to Pass-through mode supports detailed
troubleshooting, especially in bi-directional networks requiring
traffic monitoring from both ends.
Pass-through monitoring by inserting MT1000A in network
Ethernet OAM
To improve the performance of Ethernet-based networks and
provide Carrier Class service, many network providers have
enhanced their systems with Ethernet OAM (Operation,
Administration and Maintenance), supporting the ability to detect
network faults and measure performance. Ethernet OAM is defined
by three standards covering different network sections.
The ITU-T Y.1731 and IEEE 802.1ag standards are similar and
support end-to-end network functionality, while the IEEE 802.3
(previously IEEE 802.3ah) standard supports first (or last) mile
functionality.
The MT1000A tests the network using all supported OAM functions.
Ethernet Multistream
The MT1000A Ethernet Multistream function allows simulation and
testing of a congested network's ability to prioritize high-priority
traffic over low-priority traffic. The user can set different priorities for
up to 16 streams per port to measure how frame loss affects
network performance.
The Multistream function displays clear information on Packet Jitter
and Latency per stream, helping troubleshoot problematic issues
for VoIP services, etc.

Stacked VLAN
Stacked VLAN (Q-in-Q) is used increasingly by several types of
Ethernet-based networks, allowing operators to split traffic from
different customers on one line or to shape traffic by priority.
The MT1000A supports up to 8 levels of VLAN tags, offering a
powerful network test tool.
MPLS
MPLS (Multi-Protocol Label Switching) supports efficient traffic
routing on packet-based networks. Inserting up to 8 levels of MPLS
labels using the MT1000A offers a powerful tool for testing MPLS
traffic. The tester also supports EoMPLS (Ethernet over MPLS) – or
PWE3 (Pseudo Wire Emulation Edge-to-Edge) – defining the layer-
2 transport protocol across an MPLS network.
MPLS-TP and PBB/PBB-TE
The MPLS-TP (Multi-Protocol Label Switching – Transport Profile)
technology is based on standard MPLS and aims to give service
providers reliable connection-oriented packet-based transport over
the network. It supports various protocols, including Ethernet. Using
MPLS-TP offers service providers QoS, end-to-end Carrier Class
OAM, and protection switching.
The Provider Backbone Bridge Traffic Engineering (PBB-TE)
technology is designed to provide Carrier Class Ethernet-based
transport networks. It is connection oriented and includes an OAM
function offering similar functions to SDH/SONET networks.
The MT1000A is a powerful tool for testing MPLS-TP and PBB-TE
networks including OAM functions.
Protocol Analysis*
For advanced Ethernet troubleshooting the MT1000A supports a
frame capture function for capturing frames of live traffic on the
monitored line. Captured frames are analyzed using the Wireshark®
protocol analysis software.
Mobile Backhaul Installation and
Verification
Synchronous Ethernet is an essential technology in mobile
backhaul networks and faults in Synchronous Ethernet seriously
jeopardize the performance of mobile networks and can cause
system downtime. Consequently, mobile operators need a test tool
to verify the correct functioning of Synchronous Ethernet.
The Synchronous Ethernet test function of the MT1000A supports
comprehensive testing and analysis of both Synchronous Ethernet
technologies: SyncE (ITU-T G.826x), and PTP (IEEE 1588 v2).
The user can quickly identify problems at all levels in Synchronous
Ethernet, solving issues quickly, reducing system downtime and
customer churn, and improving operating expenses for mobile
operators.
Powerful Storage Area Networking
(SAN) Testing*
Many operators need to support Fibre Channel links in Storage Area
Networks (SAN) together with other transport technologies like OTN,
Ethernet, and SDH/SONET. Having one tool for all technologies is
important for efficient testing. The multi-protocol MT1000A with Fibre
Channel option is the perfect tool for deploying Fibre Channel with
support for testing links at rates up to 10 Gbps, and it also supports
other technologies like OTN, Ethernet and SDH/SONET/PDH/DSn.
The all-in-one MT1000A gives the user less equipment to maintain
and learn, helping reduce operating expenses.
Fibre Channel test features include:
• 1GFC, 2GFC, 4GFC, 8GFC, and 10GFC tests
• Optional mapping to OTN
• Latency measurement
• BER tests including service disruption measurement
• Line alarm and error monitor
Latency
High latency is a problem for many applications, including SAN,
and network operators and service providers urgently need a tool
like the MT1000A with Fibre Channel option to test latency on Fibre
Channel lines and equipment.
Fibre Channel BER Tests
The MT1000A with Fibre Channel option supports BER tests to
measure the performance of Fibre Channel lines and equipment.
Service disruption measurement is also supported.
*: Coming soon

Quick and Easy Tests of SDH/SONET/PDH/DSn Networks
Legacy technologies in transport networks can't just be eliminated because of the huge capital investment, but keeping legacy technologies
operational can require several testers.
With its SDH/SONET/PDH/DSn test options, the MT1000A is a powerful and easy-to-use tool for testing SDH/SONET up to STM-64/OC-192.
PDH/DSn systems (E1, E3, E4, DS1 and DS3) can be tested directly or embedded into SDH/SONET. The MT1000A can support new and
legacy technologies, leaving the user less equipment to maintain and learn, and reducing operating expenses.
SDH/SONET/PDH/DSn test features include:
• Powerful testing of SDH (STM-64, STM-16, STM-4, STM-1), SONET (OC-192, OC-48, OC-12, OC-3, STS-3) systems and embedded
PDH (E1, E3, E4) and DSn (DS1, DS3) systems
• Powerful testing of PDH (E1, E3, E4) and DSn (DS1, DS3) systems
• Simultaneous bi-directional monitoring of SDH/SONET/PDH/DSn lines
• SDH/SONET mapping and de-mapping of PDH/DSn signals
• Comprehensive error and alarm statistics
• SDH/SONET overhead byte testing and monitoring
• SDH/SONET tributary scan
• SDH/SONET pointer event generation and monitoring
• SDH/SONET/PDH/DSn delay measurements
• Analysis of service disruption with APS application
SDH/SONET Installing and Commissioning Testing
The MT1000A has powerful statistical measurements for BER
testing at installing/commissioning and troubleshooting out-of-
service SDH/SONET lines. Statistics are also collected for
in-service analysis of line transmission-error performance together
with information on pointer operations. G.826, G.828, G.829, or
M.2100 error-performance parameters are calculated and the
measurement result is highlighted by easy-to-understand color coding.
Errors, alarms, pointer operations and overhead byte changes can
be inserted into the transmitted signal for stress testing.
Looping-back test signal from MT1000A at far end supports SDH/SONET line quality tests
MT1000A supports bi-directional in-service monitoring of
SDH/SONET lines
MT1000A gives quick overview of errors and alarms for
both sides of SDH/SONET line
Speeds-up SDH/SONET Troubleshooting
The MT1000A monitor function speeds-up troubleshooting by
providing key information on the monitored system, including line
alarms and errors, input frequency and deviation, optical input level
and overhead bytes. Information is also available on embedded
PDH/DSn signals.
PDH (E1, E3, E4) and DSn (DS1, DS3) Testing
The MT1000A has powerful statistical measurements for BER
testing at installing/commissioning and troubleshooting out-of-
service PDH/DSn lines. Statistics are also collected for in-service
analysis of line transmission-error performance of PDH/DSn lines,
and G.826 or M.2100 error-performance parameters are calculated.
Furthermore, PDH/DSn signals can be mapped to the SDH/SONET
signal.

Specifications
MT1000A Network Master Pro Mainframe
User Interface
Display 9-inch active TFT display (800 × 480 pixels) and touch screen
Service Interfaces
USB Data Interfaces
MT1000A operates as host: USB 2.0 type A (2 ports)
MT1000A operates as device: USB 2.0 type Mini-B (1 port)
Ethernet Interface Ethernet 10M/100M/1000M, Connector: RJ45
WLAN Interface∗ IEEE 802.11 b/g/n
Bluetooth Interface Bluetooth 2.1 +EDR
∗: Available for certified countries and regions including USA, Canada, Japan and all EU countries. Please contact Anritsu for updated information.
Other Interfaces
Audio Interface
For connection of optional head set
Connector: 3.5-mm diameter jack
AUX Connector For connection of optional G0325A GPS receiver
Built-in Loudspeaker Not used
Ext. Clock
For connection of external clock signals:
SETS (E1: 2.048 Mbps), BITS (DS1: 1.544 Mbps) or 2.048 MHz TTL signal in accordance with ITU-T G.703
Connector: BNC
Miscellaneous
Battery
10.8 V rechargeable and replaceable intelligent Li-ion battery
Operating time: 4 hours (typ.)
Charging time: 3 to 6 hours (typ.)
Remaining capacity indication: %
Mains Adapter
Input: 100 V(ac) to 240 V(ac), 50 Hz/60 Hz
Output: 18 V(dc), 3.62 A (Max.)
Dimensions and Mass
257 (W) × 164 (H) × 77 (D) mm
≤2.7 kg (including MT1000A, MU100010A and battery)
Environmental
Temperature
Operating : 0° to +50°C (non-condensing)
Charging: 0° to +40°C (non-condensing)
Storage: –30° to +60°C (without Battery, AC adapter)
–20° to +50°C (with Battery, AC adapter)
Humidity
Operating: 85% RH (Max.)
Storage and Transportation: 90% RH (Max.)
EMC EN61326-1, EN61000-3-2
LVD EN61010-1
Laser Safety∗2 IEC 60825-1: 2007 CLASS 1, 21CFR1040.10 and 1040.11∗1: MU100010A with optical modules
∗1: Excludes deviations caused by conformance to Laser Notice No. 50 dated June 24, 2007
∗2: Safety measures for laser products
This product complies with optical safety standards in 21CFR1040.10, 1040.11 and IEC 60825-1; the following descriptive labels are affixed to the product.

Ordering Information
Please specify the model/order number, name and quantity when ordering.
The names listed in the table below are Order Names. The actual name of the item may differ from the Order Name.
1. Mainframe
Model/Order No. Name
MT1000A Network Master Pro
One of the following power line cords is supplied with the MT1000A
J1565A Line Cord USA
J1594A Line Cord Japan
J1566A Line Cord Europe
J1567A Line Cord UK
J1568A Line Cord Australia
J1596A Line Cord Korea
The following items are supplied with the MT1000A
Z1746A Stylus
G0309A AC Adapter
Z1817A Utilities ROM
G0310A Li-ion Battery
W3681AE MT1000A/MU100010A Quick Reference Guide
B0690A Softbag
Z1747A Carrying Strap
Z1748A Handle
B0692A ESD Box (for optical modules)
2. Module
MU100010A 10G Multirate Module
3. Options*1
MU100010A-001*2
Up to 2.7G Dual Channel
MU100010A-011*3 Ethernet 10G Single Channel
MU100010A-012*3 Ethernet 10G Dual Channel
MU100010A-051*4
OTN 10G Single Channel
MU100010A-052*4 OTN 10G Dual Channel
MU100010A-061*5 ODU Multiplexing
MU100010A-062*6
ODU Flex
MU100010A-081*7 STM-64 OC-192 Single Channel
MU100010A-082*7 STM-64 OC-192 Dual Channel
MU100010A-002 FC 1G 2G 4G Dual Channel*
MU100010A-091*8 FC 8G 10G Single Channel*
MU100010A-092*8 FC 8G 10G Dual Channel*
MT1000A-003*9 Connectivity for WLAN/Bluetooth
*: Coming soon
*1: This option can be retrofitted.
The Model/Order No. of retrofit options is “-3**”.
Example
As a retrofit, MU100010A-001 Up to 2.7G Dual Channel becomes
MU100010A-301 Up to 2.7G Dual Channel Retrofit.
In addition, specify one of the following media along with the required
option.
Z1849A: Retrofit Options in DVD-ROM
Z1850A: Retrofit Options in USB Stick
Z1851A: Retrofit Options via E-mail
*2: Includes SDH up to STM-16, SONET up to OC-48, PDH (E1, E3, E4), DSn
(DS1, DS3), OTN (OTU1) and Ethernet (10 Mbps, 100 Mbps, 1 Gbps)
*3: MU100010A-011, MU100010A-012: Only one of these options can be installed.
*5: MU100010A-061: Requires that at least one of the following options is
installed: MU100010A-001, MU100010A-051, MU100010A-052
*6: MU100010A-062: Requires that at least one of the following options is
installed: MU100010A-001, MU100010A-051, MU100010A-052
*9: Available for certified countries and regions including USA, Canada,
Japan and all EU countries.
Please contact Anritsu for updated information.
Standard Softbag
The standard accessory softbag accommodates the MT1000A with
MU100010A and accessories.
4. Optional Accessories
G0311A 1G 850 nm SX SFP
G0312A 1G 1310 nm LX SFP
G0313A 1G 1550 nm ZX SFP
G0332A 100M FX 1310 nm MM SFP
G0333A 10G SR/SW 850 nm SFP+
G0315A 10G LR/LW 1310 nm SFP+
G0316A 10G ER/EW 1550 nm 40 km SFP+
G0318A 10G ZR/ZW 1550 nm 80 km SFP+
G0319A Up to 2.7G 1310 nm 15 km SFP
G0328A 1G/2G/4G FC 850 nm SFP*
G0322A 1G/2G/4G FC 1310 nm SFP*
G0323A 1G/2G/4G FC 1550 nm SFP*
G0329A 10G LR 1310 nm SFP+
B0691A Hard Case
G0324A Battery Charger
J1569A Car 12 Vdc Adapter
J1570A Head Set
G0325A GPS Receiver
W3682AE MT1000A/MU100010A Operation Manual
Z1821A Utilities in USB Stick
J1571A Optical Cable SM LC/PC to SC/PC 3 m
J1575A Optical Cable SM LC/PC to FC/PC 3 m
J1579A Optical Cable SM LC/PC to LC/PC 3 m
J1581A Optical Cable MM LC/PC to LC/PC 3 m
J1583A Optical Attenuator 10 dB LC/PC to LC/PC
J1584A RJ45 Cable 3 m
J1585A RJ48 to Crocodile Clips Cable 3 m
J1586A RJ48 to Crocodile Clips Cable 20 dB ATT 3 m
J1588A BNC Cable 2.5 m
J1589A BNC to 1.6/5.6 Cable 2.5 m
J1591A RJ48 to Two 3-pin Banana Plug Cable 2.5 m
J1597A RJ48 Balanced PDH Cable Crossed 3 m
J1598A Bantam Cable 3 m
*: Coming soon
5. Maintenance Service
MT1000A-ES210 2 Years Extended Warranty Service
MT1000A-ES310 3 Years Extended Warranty Service
MU100010A-ES210 2 Years Extended Warranty Service
MU100010A-ES310 3 Years Extended Warranty Service

MT9090A Series
MU909011A3
MU909014/15
MT9083 Series
ACCESS Master Mini-OTDR
All-in-one test tool for fiber
construction and maintenance.
CMA5 Series
For Optical Fiber Installation
and Maintenance.
MU909020A
MU909011A3 Drop Cable Fault Locator Module
Compact fault locator instrument for an easy and accurate verification of
drop cable installation.
MU909014/15 µOTDR Module
Compact OTDR for full automatic verification of optical networks, FTTH-
PON, Metro and Core.
MU909020A Optical Channel Analyzer Module
Compact CWDM channel analyzer to verify power levels, drift and channel
presence of CWDM networks.
MU909060A Gigabit Ethernet Module
Dedicated field test solution for installation and troubleshooting Ethernet
links in the access network.
MU909060A

16 Техническое описание ▌ MS9740A
Пожалуйста, обращайтесь:
Технические характеристики могут изменяться без дополнительного уведомления
папрffsrgsrgsrgs
, 198152, нкт- етербург
р снопутиловск я ул., д.25
ел./ф кс +7 (812) 600-48-89
ел.: +7 (812) 375-32-44
www.radar1.ru
info@radar1.ru

фици льный предст витель и
вторизов нный сервис-центр
Anritsu Corporation

Тестер оптических и проводных транспортных сетей Anritsu Mt1000a

Recommandé

Recommandé

Contenu connexe

Tendances

Tendances (20)

En vedette

En vedette (20)

Similaire à Тестер оптических и проводных транспортных сетей Anritsu Mt1000a

Similaire à Тестер оптических и проводных транспортных сетей Anritsu Mt1000a (20)

Plus de onlinestuden

Plus de onlinestuden (20)

Dernier

Dernier (20)

Тестер оптических и проводных транспортных сетей Anritsu Mt1000a