2. Introduction
A Turbine is a device which converts the heat energy / Kinetic energy / Pressure Energy into
the Kinetic Energy & then to Rotational energy or directly to rotational Energy
• First century AD - Heron of Alexandria, first recognized thermal engineer
AeolipileHero of Alexandria
Reaction engine
First recorded steam engine
Source: www.wikipedia.com
15/09/16 Dr. Rohit Singh Lather
3. http://www.italoamericano.org and www.google.com
Branca's Stamping Mill
In 1629 an Italian engineer, Giovanni Branca, was
probably the first to invent an actual impulse
turbine
John Barber Gas Turbine
In 1791 John Barber, an Englishman. was
the first to patent a design that used the
thermodynamic cycle of the modem gas
turbine
15/09/16 Dr. Rohit Singh Lather
4. Types of Turbines
Turbine Family
Gas TurbineSteamTurbineHydraulic Turbine
Water exerts pressure
on blades of a turbine
Steam exerts
pressure on blades
of a turbine
Hot gases
exerts pressure
on blades of a
turbine
15/09/16 Dr. Rohit Singh Lather
8. • Steam turbine with three rotors discs (dark) and two
stator disc (white)
• Turbine Shaft is connected to the electric generator
Angle of the steam turbine blade to
increase the impact of steam
Steam Exit
15/09/16 Dr. Rohit Singh Lather
11. Introduction to Hydraulic Turbines
Water Wheel Water Turbine/Hydraulic TurbineTurbine
Generator
15/09/16 Dr. Rohit Singh Lather
12. Schematic of a Hydro Power Plant for Electricity Generation
15/09/16 Dr. Rohit Singh Lather
13. Understanding the Fluid Energy
Bernoulli Equation
Potential + Pressure + Kinetic = Constant
H = z +
𝒑
𝝆𝒈
+
𝒗 𝟐
𝟐𝒈
A cubic meter of water can give about 9800 Joules of mechanical energy for every meter it
descends and a flow of a cubic meter per second in a fall of 1 meter can provide 9800 W of power
𝑷 = 𝜼. 𝝆. 𝒈. 𝒉. 𝒒
Pressure Head
Velocity HeadTotal Head
Static Head
15/09/16 Dr. Rohit Singh Lather
14. According to the action of water on moving blades turbines can be
classified as Impulse and Reaction
Impulse Reaction
15/09/16 Dr. Rohit Singh Lather
16. • Tangential flow turbines: In this type of turbines, the water strikes the runner in the direction
of tangent to the wheel. Example: Pelton wheel turbine
• Radial flow turbines: In this type of turbines, the water strikes in the radial direction
accordingly, it is further classified as,
- Inward flow turbine: The flow is inward from periphery to the centre. Eg.: old Francis turbine.
- Outward flow turbine: The flow is outward from the centre to periphery. Eg.: Fourneyron
turbine
• Axial flow turbine: The flow of water is in the direction parallel to the axis of the shaft.
Example: Kaplan turbine and propeller turbine
• Mixed flow turbine: The water enters the runner in the radial direction and leaves in axial
direction. Example: Modern Francis turbine.
According to the Direction of Flow Through Runner
15/09/16 Dr. Rohit Singh Lather
17. • High head turbine: In this type of turbines, the net head varies from 150m to 2000m or even
more, and these turbines require a small quantity of water. Example: Pelton wheel turbine
• Medium head turbine: The net head varies from 30m to 150m, and also these turbines require
moderate quantity of water. Example: Francis turbine
• Low head turbine: The net head is less than 30m and also these turbines require large
quantity of water. Example: Kaplan turbine
According to the Head at Inlet of Turbine
According to Head and Quantity of Water Available
• Low head and high rate of flow
• High head and low rate of flow
• Medium head and Medium rate of flow
15/09/16 Dr. Rohit Singh Lather
18. • The specific speed of a turbine is defined as, the speed of a geometrically similar turbine that
would develop unit power when working under a unit head (1m head)
• Low specific speed turbine: The specific speed is less than 50. (varying from 10 to 35 for single
jet and up to 50 for double jet ) Example: Pelton wheel turbine
• Medium specific turbine: The specific speed is varies from 50 to 250. Example: Francis turbine
• High specific turbine: the specific speed is more than 250. Example: Kaplan turbine
According to the Specific Speed of the Turbine
According to the Disposition of Shaft
• Horizontal turbine
• Vertical turbine
15/09/16 Dr. Rohit Singh Lather
19. • In the impulse turbine, the total head of the incoming fluid is converted in to a large velocity
head at the exit of the supply nozzle
• That is the entire available energy of the water is converted in to kinetic energy
• Although there are various types of impulse turbine designs, perhaps the easiest to understand is
the Pelton wheel turbine
• It is most efficient when operated with a large head and lower flow rate
Impulse Turbine
15/09/16 Dr. Rohit Singh Lather
20. • The only hydraulic turbine of the impulse type in common use, is named after an American
engineer Laster A Pelton, who contributed much to its development in about 1880
• Known as Pelton Turbine or Pelton Wheel
• Oldest form of water turbine is Pelton Turbine
• A natural head of a stream of water is utilized to drive it
• It is an efficient machine particularly suited to high heads, in excess of 450 m
• The rotor consists of a large circular disc or wheel on which a number (seldom less than 15) of
spoon shaped buckets are spaced uniformly round is periphery
• The wheel is driven by jets of water being discharged at atmospheric pressure from pressure
nozzles
• The nozzles are mounted so that each directs a jet along a tangent to the circle through the
centres of the buckets
Pelton Turbines
15/09/16 Dr. Rohit Singh Lather
21. • Down the centre of each bucket, there is a splitter ridge which divides the jet into two equal
streams which flow round the smooth inner surface of the bucket and leaves the bucket with a
relative velocity almost opposite in direction to the original jet
Depending on water flow and
design, Pelton wheels can operate
with heads as small as 15 meters
and as high as 1800 meters
The Pelton wheel is
most efficient in high
head applications
15/09/16 Dr. Rohit Singh Lather
22. • For maximum change in momentum of the fluid and hence for the maximum driving force on the
wheel, the deflection of the water jet should be 180 degree
• In practice, however, the deflection is limited to about 165 degree, so that the water leaving a
bucket may not hit the back of the following bucket
• Therefore, the camber angle of the buckets is made as 165 degree
15/09/16 Dr. Rohit Singh Lather
24. • Best suited -for higher flow rate and lower head situations.
• The rotation of runner or rotor is partly due to impulse action and partly due to change in
pressure over the runner blades; therefore, it is called as reaction turbine
• The penstock pipe feeds water to a row of fixed blades through casing
• These fixed blades convert a part of the pressure energy into kinetic energy before water enters
the runner
• The water entering the runner of a reaction turbine has both pressure energy and kinetic energy
• Water leaving the turbine is still left with some energy (pressure energy and kinetic energy)
Since, the flow from the inlet to tail race is under pressure, casing is absolutely necessary to
enclose the turbine.
• In general, Reaction turbines are medium to low-head, and high-flow rate devices. The reaction
turbines in use are Francis and Kaplan
Reaction Turbines
15/09/16 Dr. Rohit Singh Lather
25. Francis Turbine
• Francis Turbine is an inward flow reaction turbine
• Designed and developed by the American Engineer James B. Francis
• It is a mixed flow turbine in which the water enters the runner radially at its outer periphery and
leaves axially at its center
• This arrangement provides a large discharge area with the prescribed diameter of the runner
• Suitable for large quantity of water and low and medium heads
15/09/16 Dr. Rohit Singh Lather
26. Power plants with net heads ranging from 20 to 750 m
15/09/16 Dr. Rohit Singh Lather
27. The main parts of a radial flow reaction turbine are:
• Casing: - The water from penstocks enters the casing which is of spiral shape in which area of
cross section of casing goes on decreasing gradually. The casing completely surrounds the runner
of the turbine.
• Guide mechanism: - It consists of stationary circular wheel all round the runner of the turbine.
The stationary guide vanes are fixed on guide mechanism. The guide vanes allow the water to
strike the vanes fixed on the runner without shock at inlet.
• Runner: - It is a circular wheel on which a series of radial curved vanes are fixed. The surfaces of
the vanes are made very smooth. The radial curved are so shaped that the water enters and
leaves without shock.
• Draft tube: - The pressure at the exit of the runner of reaction turbine is generally less than
atmospheric pressure. The water exit cannot be directly discharged to the tail race. A tube or
pipe of gradually increasing area is used for discharging water from the exit of turbine to the
tailrace. This tube of increasing area is called draft tube.
15/09/16 Dr. Rohit Singh Lather
34. • If the water flows parallel to the axis of the rotation of the shaft, the turbine is known as axial
flow turbine
• If the head at the inlet of the turbine is the sum of pressure energy and kinetic energy and
during the flow of water through runner a part of pressure energy is converted into kinetic
energy, the turbine is known as reaction turbine
• For the axial flow reaction turbines, the shaft of the turbine is vertical. The lower end of the
shaft is made larger which is known as hub. The vanes are fixed on the hub and hence hub acts as
runner for axial flow reaction turbine
• The following are the important type of axial flow turbines: Propeller turbine and Kaplan turbine
• When the vanes are fixed to the hub and they are not adjustable, the turbine is known as
propeller turbine
• If vanes on hub are adjustable the turbine is known as a Kaplan turbine. This turbine is suitable
where a large quantity of water at low heads is available
Axial flow turbines
15/09/16 Dr. Rohit Singh Lather
35. Kaplan Turbine
• Kaplan turbine is a
- Axial flow turbine (high flow)
- Low Head
- High Specific speed
- Reaction Turbine
• The runner blades are adjustable and can be rotated about the pivots fixed to the boss of the
runner
• The blades are adjusted automatically by servomechanism so that at all loads water enters them
without shock
High efficiency is maintained at part loads
15/09/16 Dr. Rohit Singh Lather
39. Power plants with net heads ranging from 10 to 70 m15/09/16 Dr. Rohit Singh Lather
40. • Designed by Austrian engineer Viktor Kaplan in Brno in 1913. Kaplan turbine is the only type of
water turbine with adjustable blades
• Adjustable blades allow work with low performance. For example in small hydro power plants
• Water under pressure flush draft tube through the wicket gate and falls on the adjustable
blades, which enables adjust the flow
• After crossing propeller is the kinetic energy of water converted into rotational motion shaft
• The shaft powered generator producing electric power
• The draft tube should be full of water, because the suction causes pressure drop which results in
Cavitation
15/09/16 Dr. Rohit Singh Lather