How to set up TCP/IP LAN Communication between fingerprint reader and software
1. SECUBIO TECHNOLOGY(CHINA) HOLDINGS CO.,LTD
اﻟﺒﺼ ﻤﺎت ﻣﺎﺳ ﺤﺔ, اﻟﺤﻀ ﻮر وﻗ ﺖ ﺑﺼ ﻤﺔ, اﻟ ﺪﺧﻮل ﻟﻤﺮاﻗﺒ ﺔ اﻷﺻ ﺎﺑﻊ ﺑﺼ ﻤﺎت
How to connect device with
PC computer by TCP/IP:
1. When Power is on, Please make Fingerprint reader connect with
Router by Network cable
(During its connection, Please double care that it may arise unsuccessful
connection for the reason of the port disconnected between Network cable
and Fingerprint-reader and meanwhile Failure Ping for Fingerprint reader
communication,
2. Before operating the Attendance software, Please set up the special
parameters exclusively for Fingerprint reader communication as
follows:
Menu----.Setting-----.CommSet-----OK-----TCPIP-----IP Address
(Note: When you set up the IP address for Fingerprint reader, Please double care
about the bellowed information in advance,
For instance, the IP address information of PC that we used now is listed below:
The IP address between fingerprint reader and PC must be in the same Network
section, but it prohibited to absolutely same together, otherwise it will arise
conflict for IP address,
Please see above photo, that’s the LAN communication screenshot, you can find
if your PC’ s IP is 192.168.0.144, and accordingly you can freely make the IP
address of your Fingerprint reader by following address whatever you like,
192.168.0.224,
192.168.0.223,
192.168.0.222
192.168.0.212
Fingerprint time attendance, Fingerprint access control, card system;
www.secubio.com
2. SECUBIO TECHNOLOGY(CHINA) HOLDINGS CO.,LTD
اﻟﺒﺼ ﻤﺎت ﻣﺎﺳ ﺤﺔ, اﻟﺤﻀ ﻮر وﻗ ﺖ ﺑﺼ ﻤﺔ, اﻟ ﺪﺧﻮل ﻟﻤﺮاﻗﺒ ﺔ اﻷﺻ ﺎﺑﻊ ﺑﺼ ﻤﺎت
But please make sure the last three parameter just like 224,223,222,212 must
be no more than 224, it’s very important,
225 will be prohibited according to regulation of IP address, Meanwhile the IP
address of your fingerprint reader can not be same as other PC’s IP address in
local area network(LAN),
In other means, there is strictly prohibited that two same IP address in the same
LAN with same Router, No matter what IP address is for PC or fingerprint reader,
Otherwise it will be the conflict IP in network,
Additionally the device IP in software must be absolutely same with fingerprint
reader hardware
( For example , The IP of your PC is
192.168.0.144, The Fingerprint reader hardware is 192.168.0.212,and
then the device IP in software must be 192.168.0.212)
The detail setting-up of fingerprint reader hardware, Please check photo as
follows just as an example to show ,you how to set up IP address,sunet
mast,gateway,port for LAN communication,
2) The port of software and fingerprint reader hardware should be the
same one, if port of fingerprint reader is 5005, and accordingly the port
of software is 5005,
3) The DefGateway must be in the same network section with PC’s IP
address,
For example, the IP of PC is 192.168.0.144, and then the DefGateway should be
set up as 192.168.0.1 (“0” stands for same network section, For “1”,you can’t
change it in any time),
4)You can check the video for get more details about how to make
TCP/IP setting-up between software and hardware,,
Fingerprint time attendance, Fingerprint access control, card system;
www.secubio.com