1. An airfoil produces both lift and drag when placed in an airstream. Lift is many times greater than drag and is produced partly due to lower pressure over the upper surface of the wing according to Bernoulli's theorem.
2. The pressure distribution around an airfoil changes with angle of attack. At low angles, minimum pressure is further aft while at high angles it moves forward, increasing the adverse pressure gradient. Beyond a critical angle, the airflow separates, reducing lift.
3. Stall occurs when the adverse pressure gradient becomes too great for the airflow to overcome, causing it to separate from most of the wing surface. This reduces lift and increases drag sharply. Stall can be alleviated by
A Good Effect of Airfoil Design While Keeping Angle of Attack by 6 Degreepaperpublications3
Abstract: Airfoil is a shape of wing or blade of (a propeller, rotor or turbine) by which a fluid generates an aerodynamic force. The component of this force perpendicular to the direction of its speed is called lift force and the component parallel to its speed is called drag forces. Here we see that if we set the angle of attack by 6 degree in fluid NACA0012 we found the aerodynamic forces with suitable positive result our research is totally based on iterations method and based on the help of cfd software.
A Good Effect of Airfoil Design While Keeping Angle of Attack by 6 Degreepaperpublications3
Abstract: Airfoil is a shape of wing or blade of (a propeller, rotor or turbine) by which a fluid generates an aerodynamic force. The component of this force perpendicular to the direction of its speed is called lift force and the component parallel to its speed is called drag forces. Here we see that if we set the angle of attack by 6 degree in fluid NACA0012 we found the aerodynamic forces with suitable positive result our research is totally based on iterations method and based on the help of cfd software.
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
Banked turn and its effects on Stall speed of an AirplaneJagrataBanerjee
This presentation is totally meant to show that -- Why an airplane needs to roll to the side of the turn? And, what are the effects of such banked turns on Stall Speed (minimum airspeed required to stay airborne) of an airplane.
Not only that, this slide also covers that why and how Stall speed will change with respect to the bank angle. Also, it shows the derivation of the formula to calculate the stall speed in a banked turn.
Hope, you will enjoy it and understand & learn a lot.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
The flow velocity over airfoils increases over the convex surface resulting in lower average pressure on the 'suction' side of the airfoil compared with the concave or 'pressure' side of the airfoil.
Meanwhile, viscous friction between the air and the airfoil surface slows the airflow to some extent next to the surface.
Airflow over an airfoil produces a distribution of forces over the airfoil surface.
Banked turn and its effects on Stall speed of an AirplaneJagrataBanerjee
This presentation is totally meant to show that -- Why an airplane needs to roll to the side of the turn? And, what are the effects of such banked turns on Stall Speed (minimum airspeed required to stay airborne) of an airplane.
Not only that, this slide also covers that why and how Stall speed will change with respect to the bank angle. Also, it shows the derivation of the formula to calculate the stall speed in a banked turn.
Hope, you will enjoy it and understand & learn a lot.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
This document is by explosives industry in which document discussed manufacturing process and flow charts details by nitric acid and sulfuric acid and tetra benzene and step by step details of explosive industry explosives industry is produced raw materials and manufacture it by manufacturing process
Toll tax management system project report..pdfKamal Acharya
Toll Tax Management System is a web based application that can provide all the information related to toll plazas and the passenger checks in and pays the amount, then he/she will be provided by a receipt. With this receipt he/she can leave the toll booth without waiting for any verification call.
The information would also cover registration of staff, toll plaza collection, toll plaza collection entry for vehicles, date wise report entry, Vehicle passes and passes reports b/w dates.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Top 13 Famous Civil Engineering Scientistgettygaming1
List of Best Scientist Who Gives Big Contribution in Civil Engineering Filed, in this we provide how they Contribute in Civil Engineering filed, For Data Collection civilthings.com helps us a lot.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
2. Introduction
It has been shown that if streamlined body is placed in a moving
airstream it produces drag, a force in the direction of the airflow it
should be note that the streamlined body we were examining was
symmetrical in shape.
This drag force was the total force produced by the streamlined
body.
Figure 2.31 - Resultant of
Lift and Drag
3. Introduction
• An aerofoil section in fact, produces lift many times greater than the
value of drag it also produces.
• Bernoulli's theorem indicated that there will be a reduction in
pressure over the upper surface of the wing; this reduction provides
approximately two thirds of the lift produced by a wing. The general
pressure distribution over the surfaces of a wing at a small angle of
attack is illustrated in Figure 2.32.
Figure 2.32 (a) - Pressure distribution around an
aerofoil at a low angle of attack
5. The upper surface of the wing produces a considerable
reduction in pressure but the lower surfaces produce a
mixture of increase and decrease in pressure as well.
At the leading edge of the wing, point A, the full pressure is
felt, this being the stagnation point
As the air moves over the upper surface of the wing,
towards station B, it is approaching an area of lower
pressure and at station B the pressure is just atmospheric or
static.
Past station B the pressure steadily reduces until it reaches
its minimum value at C as indicated by the longest vector,
and after C as the air moves towards the trailing edge of the
wing the pressure, although below static pressure, is now
gradually increasing.
PRESSURE DISTRIBUTION AROUND AIRFOIL
Figure 2.32 (a) - Pressure distribution around an
aerofoil at a low angle of attack
6. The fact that the air travelling from C towards D at the
trailing edge is now moving against an adverse
pressure gradient is of considerable importance when
we come to discuss stalling.
On the under-surface of the wing at point A the
pressure was above static, in fact the full dynamic
pressure was felt there and to some extent an
increase in pressure is felt on the under-surface of tie
wing up to about point E.
There after the wing under-surface produces a small
venturi of its own which gives a reduction in pressure,
and in order to limit this reduction the under-surface
of the wing is given considerably less curvature than
the upper.
The pressure distribution as shown in Figure 2.32 (a),
is for a comparatively small angle of attack, say about
4°C. Changes in the angle of attack of the aerofoil
produce very considerable changes in the pressure
distribution and Figure 2.32 (b) illustrates the pressure
pattern at a high angle of attack, say about 12°.
Figure 2.32 (a) - Pressure distribution around an
aerofoil at a low angle of attack
PRESSURE DISTRIBUTION AROUND AIRFOIL
7. PRESSURE DISTRIBUTION AROUND AIRFOIL
Figure 2.32 (b) - Pressure distribution around
an aerofoil at a high angle of attack
8. The most obvious difference between Figure 2.32 (b) and (a) is the change of
shape of the below static pressure on top of the wing.
The main feature of this new shape is that the point of minimum pressure is very
much nearer the leading edge of the wing than it was before.
This means that the air traveling from C to the trailing edge of the wing has to
deal with a very much longer and larger adverse pressure gradient.
The only means available to the air to travel against this adverse pressure
gradient is its own kinetic energy - its energy of motion, and if that adverse
pressure gradient proves to be too great for the kinetic energy of the air, the
flow will in fact break away from the wing.
On the undersurface of the wing the effect of the increase in pressure is
enhanced, thus providing more lift and the small amount of negative pressure
towards the trailing edge has been reduced
PRESSURE GRADIENTS
9. • overall effect of the increase in the angle of attack is to increase lift
but this process can only be carried out to a certain point and when
this point is reached, the wing stalls.
• The relationship between the angle of attack and lift is illustrated
below. It can be seen that there is a steady increase in lift as the angle
of attack increases and then a sudden decrease at the stalling angle
which occurs at about 16°.
PRESSURE GRADIENTS
10.
11. Lift can be increased by increasing the :
• Angle of attack
• Wing Area
• Velocity
• Density of air
• Changing the shape of the airfoil
• Then Lift :
• When the force of lift (L) = force of gravity (G), the aircraft maintain
level flight
Lift Equation
For Training Purpose Only
2
1
2 L
V C S
14. Lift/Drag Ratio
• Lift and drag vary with the angle of attack and the variations of these
two are shown in Figure 2.35 and 2.36.
Figure 2.35 - CL
relationship
with Angle of
Attack
Figure 2.36 - CD
relationship with
Angle of Attack
16. Movement of the Centre of Pressure
• Previously the centre of pressure was defined as that point on the
chord line through which the lift can be considered to act. The vector
representing lift through the centre of pressure passes through the
point of minimum pressure on the upper surface of the aerofoil.
17. For Training Purpose Only
• As air flows along the surface of a wing at different
angles of attack will resulting pressure distribution
[Center of Pressure]
• At high angles of attack the center of pressure moves
forward.
• At low angles of attack the center of pressure moves
aft.
• If the angle of attack becomes too great, the airflow
can separate from the wing and the lift will be
destroyed (Stall).
Movement of the Centre of Pressure
19. Aerofoil Terminology
For Training Purpose Only
Center of Pressure
Important concepts used to describe the airfoil’s
behavior when moving through a fluid are:
The aerodynamic center, which is the chord-wise
length about which the pitching moment is
independent of the lift coefficient and the angle of
attack.
The center of pressure, which is the chord-wise
location about which the pitching moment is zero.
20. Spanwise Distribution of Pressure
• The amount of lift produced by the upper
surface of the wing will gradually decrease
from root to tip. This means that although
the pressure on top of the wing is all
below static pressure, it is much lower
near the root than it is near the tip.
• On the underside of the wing the reverse
applies and the pressure near the root is
much higher than it is near the tip. Looked
at in plan view, this will cause the air
flowing over the upper surface of the wing
to be deflected inwards and the air flowing
over the underside of the wing to be
deflected outwards.
Wing tip and
trailing edge
vortices
21. Stall
Introduction
• It has already been shown that the lift produced by a wing steadily
increases as the angle of attack is increased, but only up to a certain
point. Past this angle of attack the lift decreases rapidly and the angle
at which this occurs is known as the stalling angle.
The Determining Factor
• A stall is produced when the airflow has broken away from most of
the upper surface of the wing. The determining factor in this is the
angle of attack: the wing always stalls at a fixed angle, usually in the
region of 15°.
22.
23. The Cause
• The cause of the stall is the inability of the air
to travel over the surface of the wing against
the adverse pressure gradient behind the
point of minimum pressure.
• Figure 2.40 illustrates the pressure
distribution over the upper surface of the
wing at a small angle of attack, say about 4°.
The minimum pressure point is at B, and the
air travels from A to B without difficulty as it is
moving from high to low pressure.
• However, from B to C it is being forced to
travel from low to high pressure, that is,
against an adverse pressure gradient. This
poses no problems at low angles of attack
because the kinetic energy of the air is
adequate to take it to the trailing edge
Stall
Figure 2.40 - Point
of minimum
pressure
24. • As angle of attack is increased
however, the minimum pressure
point moves forward and the
distance B to C increases until at
the stalling angle, it covers most
of the wing.
• This is illustrated in Figure 2.41.
When the angle of attack reaches
a certain value the air runs out of
kinetic energy and breaks away
from the surface of the wing in a
random manner. Lift decreases
sharply and drag increases
considerably.
Figure 2.41 - Pressure
reduction at a high
angle of attack
Stall
25. Alleviation
Various design features can be incorporated in the
wing which will assist in ensuring that the root of the
wing stalls before the tip. These are:
The wing may be twisted so that the tip is at a
smaller angle of incidence than the root, which will
ensure that the root reaches its stalling angle before
the tip. This is known as 'Wash-out'.
The cross-section of the wing tip may be given a
higher camber than the root, which will give it a
higher coefficient of lift.
A stall-inducer may be fitted to the wing root as
illustrated in Figure 2.42. These strips reduce the
effective camber of the root. This reduces its
coefficient of lift and will cause it to stall before the
tip.
Figure 2.42 - Sall inducer (or "stall strip")
26. Engine Power Effect
If engine power is on there will be a reduction of stalling speed
compared with the power-off stalling aircraft With propeller-driven
this is due to:
Vertical component thrust
The propeller slipstream over the wings speed.
27.
28. Altitude Effect
• In straight and level flight at the stall, for a given wing area, cross-
section and weight, the lift is L of fixed value. This is a most fortunate
occurrence when one considers the lift equation:
• As lift at the stall is a fixed value and angle of attack, wing area and
coefficient of lift are also constant, the total value of must also
be constant.
• is dynamic pressure shown on the airspeed indicator and it is
for this reason that for a given weight an aircraft will always stall at
the same indicated airspeed regardless of height.
2
1
2 L
Lift V C S Angleof attack
2
1
2
V
2
1
2
V
29. Weight Effect
Any change of weight will require a different value of lift for straight
and level flight, an increase in weight requiring an increase in lift.
At the stalling angle in level flight, the greater the weight the more
the lift required and, therefore, the higher the stalling speed. A
useful rule of thumb in this context is that the percentage increase in
stalling speed is half the percentage increase in weight, Thus:
Weight 2000 Ib, normal stalling speed 100 kt.
Weight 2200 Ib, percentage increase 10%, stalling speed increases
5%, i.e. to 105 kt.
30. Loading in Turns
The same effect is produced during manoeuvres, which produce a G loading, for instance, turns.
During a turn the lift not only has to balance the weight but also the centrifugal force resulting
from the aircraft moving in a curved path.
Because of his the lift has to be greater than in level flight and, provided the speed is kept
constant, the only way that this extra lift can be derived is by an increase in angle of attack.
This increase in angle of attack puts the aircraft wing nearer to the stalling angle. The result of
having to produce effectively more lift from the wings is that the aircraft's weight appears to be
increased, hence the expression G loading. The increase in stalling speed is calculated by taking
the normal stalling speed in level flight for the aircraft's weight and multiplying it by the square
root of the G loading.
• For example:
• Normal stalling speed 100 kt,
• Stalling speed in a 2G turn
Further details of calculating staling speeds are given later in this chapter.
100 2
100 1,4
140kt
x
x
31. Effect of Shape
• A wing does not normally stall over its entire length simultaneously.
The stall begins at one part of the wing and then spreads.
• The main factor governing where the stall begins is the shape of the
wing, and will be dealt with in a later section.
• It is plainly undesirable that a wing stalls from its tip first as this can
lead to control difficulties.Any tendency to drop a wing at the stall
may well lead to spinning.
• Further advantages of having a wing stall from its root rather than tip
first are that aileron control can be maintained up to the point of full
stall and the separated airflow from the wing root will cause buffet
over tie tail which serves to act as a stall warning
32. • When the angle of attack increases to high values the upward
inclination of the thrust line provides a vertical component which acts
in concert with the lift to support the aircraft's weight.
• The slipstream from the propeller increases the speed of the air
flowing over the wing, thus delaying the stall. Caution should be
exercised in power-on stalls as their effect may result in a tip stall on a
wing which normally stalls from the root.
Effect of Shape
33. Centre of Gravity Position Effect
• The stalling speed will be affected by the position of the centre of
gravity. If the centre of gravity is forward of the centre of pressure a
down-load is required from the horizontal stabilizer.
• The effect of this is that the lift is supporting not only the weight
through the centre of gravity but also the down-load on the tail,
therefore the lift will have to be higher and in turn the stalling speed
will be higher.
• The nearer that the centre of gravity approaches to the centre of
pressure, the less will be the down-load and the stalling speed will
consequently be reduced.
34. Centre of Gravity Position Effect
Figure 2.43 - Change in the position of
Centre of Gravity - Effect on stall
35. Icing Effect
• The effect of ice formation on a wing is
to corrupt the camber of the wing and
so considerably to reduce the coefficient
of lift.
• This can be brought about by extremely
thin layers of ice - even hoar frost - and
the utmost care must be taken to de-ice
the wings of an aircraft prior to takeoff if
there is any suggestion that ice may be
present on the wings.
• The drastic effect of ice in reducing the
coefficient of lift and, as a result, causing
the stalling speed to be much higher
than normal is illustrated in Figure 2.44.
Figure 2.44 - Stall angle with and
without icing
36. Stall Warning Devices
• It is not normal to have an angle of attack indicator on the flight deck;
it is usual instead to have some form of stall warning alarm operated
by a switch which is sensitive to angle of attack. The warning may take
the following forms:
• A visual warning, example a flashing light.
• Audible warnings, example a horn.
• A stick shaker.
37. Spinning
• Following a stall involving a wing drop, a spin may develop. Referring to Figure
2.45, the wing which drops increases its effective angle of attack due to having
acquired a downward velocity.
• This increase in angle of attack causes a further decrease in lift and an increase in
drag. The up-going wing, however, experiences a decrease in angle of attack and
an increase in lift.
• The lift has been reduced on the downgoing wing it will continue to drop and any
attempt to raise it by the use of ailerons merely aggravates the situation because
it will increase the angle of attack still further. At the same time the increase in
drag on the downgoing wing, coupled with a decrease in drag on the up-going
wing, will produce a yawing moment towards the dropped wing.
• From this it can be seen that the aircraft will roll and yaw towards the dropped
wing, and this motion may be self-sustaining. If it is self-sustaining, the motion is
described as a spin.
39. The Deep Stall
• Conventional recovery from a stall is by easing the stick forward to lower
the nose and then applying power.
• However, some aircraft of current design will enter into what is known as a
deep stall, or a super-stall, from which normal recovery is not possible.
Broadly speaking, these aircraft have swept back wings, high speed wing
sections and a high T-tail.
• The airflow following a stall in a conventional aircraft is illustrated in Figure
2.46. It can be seen that although the air has broken away in a random
manner from the upper surface of the wing, the horizontal stabilizer and
the elevators are still in undisturbed air. The result of this is that the
horizontal stabilizer will produce a sharp nose down pitch which may be
assisted by application of elevator.
40. Figure 2.46 -- Effect of aircraft tail
configuration on Deep Stall
The Deep Stall
41. • This can be contrasted with the state of affairs when an aircraft with a high T-tail is stalled. This
time the separated air from the wings, following the stall, entirely covers the horizontal stabilizer
and elevators, virtually reducing their effectiveness to nil. In the case of aircraft with sweep back
on the wings, the wing itself may develop a nose up pitching moment after the stall.
• This is due to the tendency of a swept wing to stall at the tip and so cause the centre of pressure
to move forwards. The situation is often aggravated because the aircraft has now acquired a
vertical downward velocity which will progressively increase the angle of attack way beyond the
stalling angle.
• Finally, this type of aircraft is often equipped with rear-mounted engines and the effect of
turbulent air entering the engine intakes may be to cause them to flame out, causing a complete
loss of power.
• Obviously an aircraft with these characteristics cannot be permitted to stall. When such an
aircraft is first built, it is equipped with a tail-mounted parachute for use in test flying to thing the
nose down in the event of it entering a super-stall.
• For general airline operation, aircraft of this type are fitted with equipment called a stick pusher.
This is actuated by an angle of attack sensor on the fuselage (usually de-iced) which senses that
the angle of attack is approaching the stall. Signals are then sent to an electro-hydraulic system,
the rams of which physically push the control stick forward, thus preventing the aircraft from
entering the stall.
The Deep Stall
42. Stall Speed and Stall Angle
Calculation of the stalling speed.
During level flight, lift is exactly equal and opposite to the weight.
• Therefore: (i) Lift = Weight
• The lift formula is: (ii) Lift =
• It stands to reason that when the CL is maximum, V must be a
minimum value (low speed, high angle of attack). This minimum value
of velocity is, therefore, the stalling speed (VS), when the CL is at
maximum value.
2
1
2 L
L V C S
43. Therefore: (iii) Lift = Weight =
So, rearranging the formula, it becomes:
(iv) Weight =
Thus, to obtain the V. (stalling speed), the formula is so rearranged:
Therefore (v)
Normal Stall Speed
(vi)
2
1 max
2 L
L V C S
2
1 max
2 L
L V C S
Stall Speed and Stall Angle
2 2
max
L
W
V
C S
2
max
S
L
W
V
C S
44. Factors affecting the stalling speed of an aircraft :
1. Weight
2. Load Factor
3. Wing Area
4. Change in CL(max)
5. Power and Slipstream
Stall Speed and Stall Angle
45. 1. Weight
Any change in the weight of an aircraft will affect the stalling speed. It
will be noted from the formula:
that if the weight increases, the division thereof by CL(max) S results in an
increased stalling speed (Vs)
2
max
S
L
W
V
C S
Stall Speed and Stall Angle
46. 2. Load Factor
Any manoeuvre that requires an increase in total lift without a
corresponding increase in wing area, must increase the effective total weight
acting on the aerofoils.
This apparent weight increase is known as a load factor, which is defined as
the ratio of the load acting on the aircraft during the manoeuvre to the
loading acting on the aircraft in straight and level flight.
As demonstrated in the previous paragraph, any increase in weight results in
a higher stalling speed. This new stalling speed may be calculated from the
following formula:
Stall Speed and Stall Angle
Total Lift TotalWeight
Load Factor
TotalWeight ActualWeight
s
NewV OldVs x Load Factors
47. 3.Wing Area (S)
Where increased wing area is obtained by the use of Fowler flaps, the
division of a given weight by an increased value of (S) results in a lower
value of V.
Stall Speed and Stall Angle
48. 4.Change in CL(max)
• The use of flaps increases the CL of that wing. Once again, the division
of a given weight by a larger value of CL results in a lower stalling
speed.
• This is the advantage of the use of flap during the landing manoeuvre
because it permits the original value of lift to be retained at a lower
speed. It is particularly useful in the lowering of the approach speed.
Stall Speed and Stall Angle
49. 5. Power and Slipstream
• When power is applied at the stall, the already nose-high attitude
produces a vertical component of thrust as shown in Figure 2.47.
• This consequently reduces the work load (i.e. weight) of the wings
and allows a much lower stalling speed to be attained.
• The slipstream at high power settings provides an extra boost to the
stagnating airflow over the aerofoil and thus controls the boundary
layer.
Stall Speed and Stall Angle
50. Figure 2.47 - Vertical
component of thrust
Stall Speed and Stall Angle
51. Wing Tip Stalling
An aircraft wing is designed to stall progressively from the root section
to the tips.
The reasons for this are as follows:
An early buffeting is induced over the tail sections.
Aileron effectiveness is maintained up to the stalling angle of attack.
Large rolling moments of the aircraft are prevented in the event of
one wing tip stalling before the other.
52. Methods used in the prevention of tip stalling:
• Washout:
This is a progressive reduction of wing incidence from the root to the tip. This results in
the wing root reaching the critical angle of attack before the tip.
• Root spoilers:
This method employs a triangular-section strip fixed to the leading edge of the wing near
the root. At high angles of attack, the airflow is obstructed in following the contour of the
leading edge and this results in a breakdown of the airflow whereby an early stall is
induced at the wing root.
• Change of aerofoil section:
The aerofoil section may be gradually changed by decreasing the camber slightly at or
near the tips, or by sweepback. This results in a slight decrease in lift at the tips thus
giving an aerofoil with more gradual stalling characteristics from the root to the tip. The
effect of sweepback is to increase the stalling angle.
Wing Tip Stalling
53. • Slats and Slots
By employing slats and slots on the outboard
sections of the wing, the effective angle of
attack at that part of the wing is decreased.
Thus, when the root section reaches the critical
angle of attack, the tip sections remain un-
stalled.
Note: Tapering the aerofoil from root to tip
gradually reduces the CL towards the tips; this
in itself reduces the high rolling moment which
would occur if one tip stalled before the other.
Wing Tip Stalling
54. Figure 2.48 - Effect of flaps, slats
and slots on stall angle
Wing Tip Stalling
56. • Aspect Ratio Effect
Note: When referring to stalling angle, it is that angle with
the horizon as viewed abeam by the pilot from the flight
deck.
As discussed under wing tip vortices, the net direction of
the airflow is altered.
Aircraft having high aspect ratios (long span and short
chord) have very little induced downwash and, therefore,
the net direction of the airflow remains largely unaltered.
Conversely, aircraft with low aspect ratio wings (broad tips)
induce a large amount of downwash which alters the net
direction of the airflow significantly. These effects are
illustrated in Figure 2.50.
Because of this altered airflow, low aspect ratio wings have
significantly higher stalling angles than do wings of high
aspect ratio.
Wing Tip Stalling
Figure 2.49 - Effect of Aspect Ratio
on lift and stall agle
57. Wing Tip Stalling
Figure 2.50 - Effect of induced downwash on angle of
attack
Figure 2.51 - Effect of induced downwash at wingtip,
compared to wing root
58. • Sweepback Effect
• In itself, a swept wing has a low aspect ratio and thus the presence of
wing tip vortices are marked and give rise to a downwash that alters
the net direction of the relative airflow.
• Since an aerofoil stalls when the critical angle between the chord line
and the relative airflow is exceeded, the presence of the downwash
alters this relative airflow and, having a downward component,
results in the stalling angle being higher when the critical angle of
attack is reached.
• Swept wings therefore, have higher stalling angles than those of
unswept wings.
Wing Tip Stalling
59. Figure 2.52 - Effect of wing planform on stall
propagation
Sweepback Effect
60. • Flap Effect
With each successive increase of flap, the
characteristics of the aerofoil are changed, i.e. the
chord line assumes a steeper inclination, being the
straight line from leading edge to trailing edge.
The critical stalling angle (about 15 degrees) is
therefore reached with little or no inclination of the
longitudinal axis of the aircraft (i.e. aircraft in
straight and level attitude).
Any further increase in flap setting in this attitude
would result in the critical stalling angle of attack
being exceeded. To prevent this, the aircraft would
have to be placed in a nose down attitude, thereby
reducing the critical angle of attack to within limits
(about 15 degrees).
Figure 2.53 - The effect on chord line and
hence angle of attack of flap deployment
Wing Tip Stalling
61. The effect on chord line and hence angle of attack
of flap deployment
Figure 2.53 - The
effect on chord line
and hence angle of
attack of flap
deployment
62. • Thus, the effect of flap reduces the stalling angle although the critical
angle of attack remains about 15 degrees.
• Note: The stalling angle, or level flight stalling angle, is increased
when leading edge flaps are employed. Further reference to wing
planforms and their stall characteristics are discussed in Chapter 8.3.
Wing Tip Stalling