CoolJunk is India's fastest growing DIY (do-it-yourself) kits company focused on project-based learning in science, engineering and technology. Having 20,000 users in India, US, Singapore, Middle East and New Zealand, the CoolJunk kits are known for quality, innovation and high production value. CoolJunk has been featured in national and international journals including Wallstreet, Yourstory, Hindu Business Line, NextBigWhat and was tagged as the coolest Indian start-up in IAN Bootcamp-2011.
11. - 8 Pins, DIP
- Each pin has a different function
- Voltage range is 4.5-15V
- To power it, pin 8 is given Vcc
and pin 1 is grounded
- Pin 2 is Input
- Pin 3 is Output
- 200mA of current from output pin
555 Specifications
16. Experiment 1
• Rotate 4K7 potentiometer to the maximum value.
• Take Voltage reading at Pin 2 (Red probe at pin 2
and black probe to –ve terminal of battery). It shall
be close to 9V.
• Press S1 (continuously) and rotate 5K. Check the
voltage reading at pin 2 until it reaches between 3-
4 volts.
• Rotate the potentiometer further and see if your
voltage reading at pin 2 is less than 3V
17. Experiment 1
• If you press S1, LED will glow for a fixed time, t.
• After LED glows, press S1. Nothing will happen.
Measure the total time for which LED glows.
• While LED is glowing, press S2 (pin 4).
Immediately, LED will be off. This is a Reset Button
18. • If you press S1, LED will glow for a fixed time, t.
• After LED glows, press S1. Nothing will happen.
Measure the total time for which LED glows.
• While LED is glowing, press S2 (pin 4).
Immediately, LED will be off. This is a Reset Button
• Replace R78 with a 1M ohm preset. At different
positions of the preset, you will notice different
timing durations (measure time with watch).
19. Pin 3 receives high when Pin 2 is low
Voltage at Pin 2 should be less than 1/3rd of Vcc
Pin 3 produces positive pulse (voltage) for time T
22. Let us create Tone
F, frequency = 1440/(R78+2R67)*C6
• Identify R78, R67 and C6 in your circuit sheet,
experiment-2
• Calculate f
• Then, implement the following circuit diagram
25. Circuit Modifications
Activity 2.1: Replace R67 with a 100K preset. Rotate it
and see what happens?---------DIFFERENT TONES
Activity 2.2: Connect two LEDs at pin 3.
One LED with its positive leg at pin 3 and the other leg grounded through a
330 ohm resistor. Second LED with its negative leg at pin 3 and the other leg
connected to Vcc through a 330 ohm resistor
Activity 2.3: Replace C6 in the circuit with 10 mfd or
100 mfd or 1000 mfd and see the difference.
26. Circuit Modifications (Home Assignment)
Activity 2.4: You can also control the volume of the
tone by using Pin 5. Replace capacitor (0.1 mfd) with
the following circuit:
27. Let us create Bistable
You create an indefinite pulse
• Then, implement the following circuit diagram
• When you press S2, LED glows. If you press S2
again, nothing will happen.
• Press S4, LED is off. Press S4 again, nothing
happens. Press S1 and LED glows again.
29. Combining two ICs
• Output of Pin 3 is used to power pin 8 of another
IC (3 1). Vmin = 60-70% of Vcc
• Output of Pin 3 is used to control pin 5 of
another IC (3 5). When 3 is high, pitch
increases. When 3 is low, pitch decreases.
• Output of Pin 3 is used to trigger another IC
(3 2). When pin 3 is low, it can trigger another
555 since its output is close to 0.5V.
33. 20 MN Gates in Pentium IV
FAST COMPUTATION
THINKING MACHINES
34. Digital IC Types
• Made from Complimentary Metal Oxide
transistors,
• 74 Series
• Consumer less power
• More sensitive to static charge
• Part Number contains alphabet “C”
• Voltage Range: 3-18 V
• Made from Bipolar Junction transistors
(Transistor- Transistor Logic)
• 4000 Series
• Consume more power
• More Sensitive to static charge
• Part Number contains alphabet
S, LS, ALS
CMOS TTL
35. 1. Give regulated 5V DC Supply
using a Voltage Regulator-7805
2. Low input (0) means (< 1V)
3. High input(1) means (> 3.5 V)
RULE1
36.
37.
38.
39. Don’t mix TTL and CMOS Chips in the same circuit
No input pin of a digital IC should be left floating or
unattended
# If it is a CMOS IC, ground the unused input pins
# If it is a TTL IC, give Vcc to the unused input pins
RULE2
45. Circuit Requirements
1. Press button first- Winner
2. Output signal latched
3. Output signal is one of the feedback
4. All buttons blocked
5. Host resets the system
46.
47. - All player buttons should be blocked once the
output signal latches from the winning team
- So, at least one player’s output is enough to
block all the buttons. Thus, all outputs can be
combined into a OR Gate.
48.
49. Two 555 timers in bistable as Latch
SPDT Switch for play and reset
In play mode, user switches receive –ve
In reset mode, reset pins of 2 timers receive –ve
Push button switches as trigger
(One side –ve and other side OR Gate )
50. Output of push buttons into 2 OR Gates
Winning user presses push button first---
Negative at Pin 2 of 555---LED glows
Output of both timers into a 3rd OR Gate
Output of 3rd gate as one of the
inputs to 2 OR gates
51.
52. When host starts the system, either of the two
LED glows. And none of the teams actually
pressed the button.
“SWITCH BOUNCING”
57. 74LS92
Counter IC, TTL family
14 pin IC, Two inputs (pin 1 and pin 14)
Four Output pins-12,11,9,8
To power it, give Vcc to pin 5 and ground to pin 10
To use it as digital counter, give input to pin 14 and connect pin 1 to pin 12
58. Binary Counter
First Run a 555 in astable mode
At Four Output pins-12,11,9,8::: Connect a (LED + R) and ground Resistors
See pin diagram and do other connections of 74LS92
Connect output (pin 3) of 555 to input A (pin 14) of 74LS92
Record the observations in the following table
See your Circuit Sheets
59. LED D LED C LED B LED A Binary
Code
Number
Glows Glows Doesn’t
Glow
Doesn’t
Glow
1100 12
Say, if Binary Number = 011
Then, Decimal Number = 2^0 * 1 + 2^1*1 + 2^2 * 0
= 1*1 + 2*1 + 0 = 1+2 = 3
60. CD 4017
Decade Counter (counts 0-9)
Output Pins- 1-7, 9-11
Pin8- Ground, Pin 16-Vcc
15, Reset Pin- Low for normal operation
Pin 14- Input Pin (Clock Input)
Pin 13- Low to enable display, high to freeze display
Pin12- Divide by 12 Output- Provides high for counts 0-4 and low for 5-9