2 data preparation process

Day 2
Data Preparation Process

Session Speaker
Ajaya Kumar.s

1

PEMP VSD531

Session objectives

After completing this session, students will be able

• To understand the physical design flow

• To understand the need for physical design

• To know about the tools used for physical design

©M.S.Ramaiah School Of Advanced Studies 2

PEMP VSD531

Session Topics

• Detailed Physical Design Flow

• Foundry Files, Parameters, Rules and Guidelines

• Processing the Cells


PEMP VSD531

Physical Design Input Data

Types of data that are required to start a physical design are

• Technology and library files

• Circuit description of the design in the form of netlist representation

• Timing requirements or design constraints

• Floorplan or the physical layout structure


PEMP VSD531

Technology and library files

• Technology File (tf)

• Library Exchange Format (LEF)

• Design Exchange Format (DEF)

• Physical library (PLIB)

• Physical Design Exchange Format (PDEF)


PEMP VSD531

Technology and library files Cont…

• Cell Library Format File (CLF)

• Advanced Library Format (ALF)

• Top Design Format File (TDF)

• Table Look up (TLU)

• Interconnect Technology Files (ITF)


PEMP VSD531

Technology rule basics

• Manufacturing grid
• Routing grid
• Standard cell placement tile
• Routing layer definition
• Placement and routing blockage layer definition
• Via definition
• Conducting layer density rule
• Metal layer slotting rule
• Routing layer physical profile
• Antenna definition
• Fringe Cap Section
• Place and Route Rule Section


PEMP VSD531

Technology rule basics Cont..

Manufacturing grid :
Manufacturing grid is determined by the smallest geometry that a semiconductor
foundry can process. All drawn geometries during physical design must snap to
this manufacturing grid.

Routing grid

Routing grids or tracks are used by physical synthesis and place-and-route tools
during detail routing. The routing tracks can be grid-based, gridless based, or
subgrid-based.

Standard cell placement tile
Standard cell placement tile is used during the placement phase. The placement
tile is defined by one vertical routing track and the standard cell height.


PEMP VSD531


Routing layer definition

Routing layer definition is used to define the layers that are used to route the
design. These definitions include wire width, routing pitch, and preferred routing
direction such as vertical, horizontal, or diagonal.

Placement and routing blockage

Placement and routing blockage layer definitions are internal to physical design
tools and are used to define “keep-out” regions for standard cell placement and
routing.

Via definition

Via definition defines the layer, size, and type for connection between overlapping
geometries of conductor for different conductive layers. This cut layer, or via, can
be a single via, stacked via, or array of via.


PEMP VSD531


Conducting layer density
Conducting layer density rule defines the percentage of area of the chip that
is required for processes that are using Chemical Mechanical Polishing (CMP)
for each physical layer in the design.

Metal layers slotting
Configuration of metal layers slotting rule defines the minimum layer width that
may need to have slotting features (i.e. a cut inside a wide routing layer). This rule
varies between foundries and is used to limit mechanical stress for a given
conducting layer
Physical profile

Physical profile for each layer is used to define and include conductor thickness,
height, and interlayer dielectric thickness. Definition of the electrical interconnect
profile includes resistance and dielectric constants.

PEMP VSD531


Antenna definition

Antenna definition for each layer configures the physical design tools for automatic
antenna repair. Antenna phenomena occur during the metallization process when
some wires connected to the polysilicon gates of transistors are left unconnected
until the upper conducting layers are deposited.

A long wire connected to the gate of MOSFT can act as a capacitor or antenna that
collects charges during the plasma-etching step. If this energy build-up on the
floating transistor gate is suddenly discharged, the transistor could suffer
permanent damage due to gate oxide breakdown.


PEMP VSD531


FringeCap Section

A FringeCap section specifies capacitance information for interconnect layers when
they are overlapping or parallel to each other.

• Capacitance per unit area when objects on different layers overlap (interfringe)

• Capacitance per unit length when objects on the same layer are separated by the
minimum spacing specified in the technology file Layer section (intrafringe)


PEMP VSD531


FringeCap Section (Interfringe)
Interfringe and Intrafringe FringeCap 4 {
number = 4
layer1 = "M2“
layer2 = "M3"
minFringeCap = 0.00022
nomFringeCap = 0.00022
maxFringeCap = 0.00022

FringeCap Section (Intrafringe)
FringeCap 4 {
number = 4
layer1 = "M2"
layer2 = "M2"
minFringeCap = 0.00017
nomFringeCap = 0.00017
maxFringeCap = 0.00017
}


PEMP VSD531


Place and Route Rule Section
PRRule Section
The PRRule section of a technology file defines cell row spacing.

Cell Row Spacing

When using double-back cell rows in your floorplan, you specify the following
row spacing rules:
• Between top edge and top edge
• Between bottom edge and bottom edge


PEMP VSD531


Row Spacing Rule for Double-Back Cells

Row Spacing Rule for Non-Double-Back Cells


PEMP VSD531


Pitch
Defines the predominant separation distance between the centers of objects on the layer. Place
and route tool uses the pitch you specify to generate wire tracks in the unit tile.


PEMP VSD531


Library Exchange Format (LEF)

The Library Exchange Format (LEF) is a method of providing library information
from a third-party database to milkyway.

LEF defines the elements of an IC process technology and associated library of
cell models and contains library information for a class of designs.

It includes:
• Layer definition
• Via
• Placement
• Site type, and macro cell definitions


PEMP VSD531


Tech Library Exchange Format (LEF) Example

TYPE ROUTING ;
DIRECTION HORIZONTAL ;
PITCH 0.200 ;
OFFSET 0.000 ;
HEIGHT 0.5900 ;
THICKNESS 0.1800 ;
FILLACTIVESPACING 0.300 ;
WIDTH 0.09 ;
MAXWIDTH 12.0 ;
AREA 0.042
RESISTANCE RPERSQ 0.1600000000 ;
CAPACITANCE CPERSQDIST 0.0001711111
ACCURRENTDENSITY AVERAGE
FREQUENCY 500
WIDTH 0.090 1.000 12.000 ;

PEMP VSD531


Cell Library Exchange Format (LEF) Example
PIN VSS
MACRO BUFTHVTD20 DIRECTION INOUT ;
CLASS CORE ; USE ground ;
FOREIGN BUFTHVTD20 0.000 0.000 ; SHAPE ABUTMENT ;
ORIGIN 0.000 0.000 ; PORT
SIZE 16.560 BY 3.690 ; LAYER METAL1 ;
SYMMETRY x y ; RECT 6.840 -0.310 16.560 0.310 ;
SITE core ; RECT 6.580 -0.310 6.840 0.500 ;
PIN Z PIN VDD
DIRECTION INOUT ;
PIN OE USE power ;
ANTENNAGATEAREA 1.071 ; SHAPE ABUTMENT ;
DIRECTION INPUT ; PORT
PORT LAYER METAL1 ;
LAYER METAL1 ; RECT 2.490 3.380 16.560 4.000 ;
RECT 5.980 1.085 6.180 1.640 ; RECT 2.230 3.190 2.490 4.000 ;
RECT 4.935 1.085 5.980 1.245 ; RECT 0.000 3.380 2.230 4.000 ;
RECT 4.475 1.085 4.935 1.375 END
END VDD

PEMP VSD531


contact_layer ( "CONT" );
routing_layer ( "METAL1" ) {
default_routing_width : 0.16;
spacing : 0.18;
pitch : 0.41;
routing_direction : horizontal;
res_per_sq : 7.7e-05;
coupling_cap : 9.13e-05;
cap_per_sq : 0.0001163;
fringe_cap : 6.9e-05;
height : 0.89;
thickness : 0.3;
max_current_density : 14.3;
min_area : 0.122;
min_enclosed_area : 0.2;
min_width : 0.16;
spacing_check_style : diagonal;
spacing_table ( "fat_spacing" ) {
index_1 ( "0, 0.3, 10.001" );
index_2 ( "0, 0.3, 10.001" );
index_3 ( "0, 1" );
values ( "0.18, 0.18", "0.18, 0.22", "0.6, 0.6", "0.18,
0.22","0.18, 0.22","0.6, 0.6", "0.6, 0.6", "0.6,
0.6", "0.6, 0.6" );
} /* end spacing_table */

PEMP VSD531


Physical Design Exchange Format (PDEF)

Physical Design Exchange Format (PDEF) information defines the elements of an
IC design relevant to physical layout, including the netlist and design constraints.


PEMP VSD531


Advanced Library Format (ALF) define the Signal Electromigration on Interconnects
analysis
LAYER METAL1 {
PURPOSE = routing ;
LIMIT {
CURRENT ave_limit {
MEASUREMENT = average ;
MAX { HEADER {
TEMPERATURE { TABLE { 85 100 105 110 120 125 } }
WIDTH { TABLE { 0.16 1 12 } }
} TABLE { 0.533 0.316 0.268 0.229 0.168 0.145
3.332 1.973 1.673 1.430 1.051 0.905
39.983 23.681 20.077 17.160 12.613 10.862 } }
}
CURRENT rms_limit {
MEASUREMENT = rms ;
MAX { HEADER {
TEMPERATURE { TABLE { 105 110 115 } }
WIDTH { TABLE { 0.16 0.32 0.64 1 5 12 } }
} TABLE { 3.537 3.537 3.537
5.639 5.639 5.639
9.523 9.523 9.523
13.760 13.760 13.760
59.939 59.939 59.939
140.486 140.486 140.486 } }
}
CURRENT peak_limit {
MEASUREMENT = peak ;
MAX { HEADER {
TEMPERATURE { TABLE { 105 110 115 } }
WIDTH { TABLE { 0.16 1 12 } }
} TABLE { 5.883 5.883 5.883
36.770 36.770 36.770
441.235 441.235 441.235 } }

PEMP VSD531


Table Look up (TLU)

TLUPlus models are a set of CapTable and ResModel generated by grdgenxo (Start-
RCXT) from ITF or provided by the foundry. It contains unit wire caps at different
spacing and widths and unit layer resistance to allow extraction engine look up
appropriate values during the extraction.

The output of TLUPlus file will be a binary file.
• Units of pf and micron (for both ITF and technology files)
• Nominal operating condition (for CapTable names only)
• Table dimension 5x16 (width vs. spacing)
• Grid points are multiples of minimum width and spacing values


PEMP VSD531


Benefits
• Single process description can be used at design and verification stages

• Advanced process effects such as metal fill and conformal dielectrics, are
directly taken into account in the CapTable generation of TLUPlus

• TLUPlus uses more accurate engine to create the cap table than capGen which was
used in TLU

• Quicker timing closure and quicker time to market

PEMP VSD531


Interconnect Technology Files (ITF)

ITF stands for interconnect technology format. It models advanced processing
information like width-and-spacing dependent RPSQ/Etch, temperature
coefficients of the second order, which the traditional technology file does not
have. comboITF, which is the combination of min/nom/max ITF, cap unit of the
CapTable, res unit of the ResModel and mapping file, will provide a means for
extraction to calculate RC according to the same ResModel presented in
the ITF


PEMP VSD531


Cell Library Format File (CLF)

CLF file function descriptions for cell definition functions used by place and route
tool.

Cell Definition Functions:
The purpose of a CLF file is to provide timing information for timing driven place
and route. The CLF file provides Astro with information about cells in the library.
The Synopsys application uses this information during
• Pin and blockage extraction
• Pad placement
• Clock tree synthesis


PEMP VSD531

Digital Standard Cell Library Deliverables

N Type Description
.doc, .txt Databook / User guide, Layer usage file
.sdb, .slib Symbols
.db, .lib Synthesis
.v Verilog simulation models
.vhd VHDL / Vital simulation models
.sp HSPICE netlists
.rcx Extracted RC netlists for different corners
.gds GDSII layout views
.drc, .lvs, .erc Report files
.lef LEF files
.fram, .cel Fram views, layout views and runset files
.plib Physical compiler views


PEMP VSD531

Physical structure of digital cell

VDD
The selection of physical structure of digital cell
is aimed at providing maximum cell density in
W1 digital designs. It is more important to provide
minimal area for the most frequently used cells.
In general, these are usually NAND cells with
two inputs, and D flip-flops
W4

Minimum center-to-center distance
W3
W2 H dtrack

W1

VSS
d1 d2

Minimum spacing Minimum width


PEMP VSD531

Physical structure of double height digital cell

VDD
H
W1
Symbol
VDD W5 Parameter Value
L

W4 H
W3 Cell height 2.88 um
W2 H

Power rail width W1 0.16 um

Vertical grid W2 0.32 um
W1
Horizontal grid W3 0.32 um
VS
S
NWell height W4 1.68 um
W2 W3
H
W5
W4 VDDH to VDDL height (Fig. 8.3) 0.72 um

W1

VDD
H 29
©M.S.Ramaiah School Of Advanced Studies

PEMP VSD531

Processing Cells

Activity Flow


PEMP VSD531

Data Preparation Using Milkyway

The Milkyway Environment


PEMP VSD531

Data Preparation Using Milkyway Cont…

The Milkyway and the data preparation functions can perform several tasks
essential for cell library and data preparation, including the following:

• Creating cell libraries
• Importing cell data
• Specifying technology information
• Writing technology information to a file
• Removing cell hierarchy
• Specifying power and ground port types
• Optimizing the standard cell layout
• Extracting pin and blockage information
• Setting place and route boundaries
• Defining wire tracks


PEMP VSD531


Flow for Creating a Milkyway Library From LEF


PEMP VSD531


Standard Cells wire tracks


PEMP VSD531


Place and Route Boundary


PEMP VSD531


Flow for Importing and Exporting a DEF File


PEMP VSD531

Design Constraints

Design constraints are ASIC design specifications that are applied during logic and
physical synthesis. Each tool attempts to meet two general design constraints
• Timing constraints
• Design rule constraints

Timing constraints are user-specified and are related to speed, area, and the power
consumption of the ASIC design.
Timing constraints utilized by physical design tools are performance related.The most
basic timing constraints are as follows
• System clock definition and clock delays
• Multiple cycle paths
• Input and output delays
• Minimum and maximum path delays
• Input transition and output load capacitance
• False paths

PEMP VSD531

Timing Constraints Cont..

Multiple cycle paths
Multiple cycle paths are for ASIC designs that have a non-single cycle clock timing
requirement. This directs the physical design tools to avoid optimization of data paths
that have non-single clock behavior.
Input and output delays

Input and output delays are used to constrain the boundary of external paths in an
ASIC design. These constraints specify point-to-point delays from external inputs to
the first registers and from registers to the outputs of an ASIC design.
Minimum and maximum path delays

Minimum and maximum path delays provide greater flexibility for physical synthesis
tools that have a point-to-point optimization capability. This means that one can
specify timing constraints from one specific point (e.g. pin or port) in the ASIC
design to another, provided such a path exists between the two specified points


PEMP VSD531

Timing Constraints Cont..

Input transition and output load capacitance

Input transition and output capacitance loads are used to constrain the input slew
rate and output capacitance of an ASIC device input and output pins. These
constraints have a direct effect on the final ASIC design timing.

False paths

False paths are used to specify point-to-point non-critical timing either internal or
external to an ASIC design. Properly identifying these non critical timing paths
has a great impact on physical design tools’ performance.


PEMP VSD531

Design Rule Constraints

Design rule constraints are imposed upon ASIC designs by requirements specified in
a given standard cell library or within physical design tools.

Design rule constraints have precedence over timing constraints because they have
to be met in order to realize a functional ASIC design. There are four types of major
design rule constraints

• Maximum number of fan-outs

• Maximum transitions

• Maximum capacitance

• Maximum wire length


PEMP VSD531

Design Rule Constraints Cont..

Maximum number of fan-outs

Maximum number of fan-outs specify the number of destinations that one cell can
connect to for each standard cell in the library. This constraint can also be applied at
the ASIC design level during the physical synthesis to control the number of
connections one cell can make.
Maximum transition constraint

Maximum transition constraint is the maximum allowable input transitions for each
individual cell in the standard cell library. Apart from each element in the standard
cell library, this constraint can be applied to a specific net or to an entire ASIC
design.


PEMP VSD531

Design Rule Constraints Cont..

Maximum capacitance constraint

Maximum capacitance constraint behaves similarly to maximum transition
constraint, but the cost is based on the total capacitance that a particular standard
cell can drive any interconnection in the ASIC design. It should be noted that this
constraint is fully independent of maximum transition, and therefore, it can be
used in conjunction with maximum transition.

Maximum wire length constraint

Maximum wire length constraint is useful for controlling the length of wire
to reduce the possibility of two parallel long wires of the same type. Parallel
long wires of the same type may have a negative impact on the noise
injection and may cause crosstalk.


PEMP VSD531

Detailed Physical Design Flow
Design Specs Fnl. Design • Architectural optimization (timing)
• Inter-group buses, bandwidth
• Clock, SI, test; validation
Synthesis Constraints
Lib.+CWLM

Floor-plan & PG • Floorplanning and custom WLM
Lib.+CWLM
• Power distribution (Internal, I/O)
Placement • I/O driver, padring design
• Board-level timing, SI

Physical re-synth
• Row definitions
• Placement of cells
Clock distribution
• Congestion analysis

Route, scan re-order
• Placement-based re-synthesis
• Noise minimization, isolation
Timing analysis, IPO • Clock distribution

Fnl., pwr., SI ECO
• Full routing
• Scan stitching, re-ordering
Reqmts. ERC, DRC, LVS

• Full RC back-annotation
• Hierarchical timing, electrical and SI analysis and
Tape-out ©M.S.Ramaiah School Of Advanced Studies
IPO/ECO 43

PEMP VSD531

Session Summary

• Technology, ckt description, timing and design constraint file are the basic input
for the physical design

• The format in which the digital libraries are supplied as a design kit in the suitable
format wrt EDA tools are studied

• Besides being the name for the data preparation tool, Milkyway is the name for
the unified database the tool interacts with.

• Libraries contain information about design cells, standard cells, macro cells, and
so on. They contain physical descriptions, such as metal, diffusion, and polygon
geometries. Libraries also contain logical information (functionality and timing
characteristics) for every cell in the library.


2 data preparation process

Recommandé

Recommandé

Contenu connexe

Tendances

Tendances (20)

En vedette

En vedette (7)

Similaire à 2 data preparation process

Similaire à 2 data preparation process (20)

Dernier

Dernier (20)

2 data preparation process