The document provides an overview of several non-traditional machining processes including Electrical Discharge Machining (EDM), Electrochemical Machining (ECM), Ultrasonic Machining (USM), Laser Beam Machining (LBM), Water Jet Cutting, and Abrasive Water Jet Cutting. For each process, the document discusses the basic technique, key advantages such as ability to machine hard materials and produce complex shapes, and limitations such as low material removal rates or inability to machine non-conductive materials. The document serves to educate readers on alternative manufacturing methods beyond traditional cutting tools and their various applications and constraints.
2. NON – TRADITIONAL MACHINING
PROCESS
Non-traditional manufacturing processes is defined as a group
of processes that remove excess material by various techniques
involving mechanical, thermal, electrical or chemical energy or
combinations of these energies but do not use a sharp cutting
tools as it needs to be used for traditional manufacturing
processes.
Non traditional machining processes, also called advanced
manufacturing processes, are employed where traditional
machining processes are not feasible, satisfactory or economical
due to special reasons as outlined below.
Very hard fragile materials difficult to clamp for traditional
machining
When the work piece is too flexible or slender
When the shape of the part is too complex
3. Electrical Discharge Machining (EDM)
This technique utilises thermoelectric process to erode undesired
materials from the work piece by a series of discrete
electrical sparks between the work piece and the electrode. EDM
uses electrical spark or thermal energy to erode unwanted
material in order to create desired shape.
4. ADVANTAGES:
By this process, materials of any hardness can be machined;
No burrs are left in machined surface.
One of the main advantages of this process is that thin and
fragile/brittle components can be machined without distortion.
Complex internal shapes can be machined.
LIMITATIONS:
This process can only be employed in electrically conductive
materials.
Material removal rate is low and the process overall is slow
compared to conventional machining processes.
Unwanted erosion and over cutting of material can occur.
Rough surface finish when at high rates of material removal.
5. Electrochemical Machining (ECM)
Electrochemical machining (ECM) is based on the principle of
reverse electroplating. In this process, particles travel from the
anodic material (workpiece) toward the cathodic material
(machining tool). A current of electrolyte fluid carries away the
deplated material before it has a chance to reach the
machining tool. The cavity produced is the female mating
image of the tool shape.
6. ADVANTAGES:
The components are not subject to either thermal or mechanical
stress.
No tool wear during ECM process.
Fragile parts can be machined easily as there is no stress
involved.
ECM deburring can debur difficult to access areas of parts.
High surface finish (up to 25 μm in) can be achieved by ECM
process.
Complex geometrical shapes in high-strength materials
particularly in the aerospace industry for the mass production of
turbine blades, jet-engine parts and nozzles can be machined
repeatedly and accurately.
Deep holes can be made by this process.
LIMITATIONS:
ECM is not suitable to produce sharp square corners or flat
bottoms because of the tendency for the electrolyte to erode
away sharp profiles.
ECM can be applied to most metals but, due to the high
equipment costs, is usually used primarily for highly specialised
applications.
7. Ultrasonic Machining (USM)
USM is mechanical material removal process or an abrasive process
used to erode holes or cavities on hard or brittle workpiece by using
shaped tools, high frequency mechanical motion and an abrasive
slurry. The hard particles in slurry are accelerated toward the surface
of the workpiece by a tool oscillating at a frequency up to 100 KHz -
through repeated abrasions, the tool machines a cavity of a cross
section identical to its own.
8. ADVANTAGES:
It is a non-thermal, non-chemical, creates no changes in the
microstructures, chemical or physical properties of the
workpiece and offers virtually stress free machined surfaces.
Any materials can be machined regardless of their electrical
conductivity
Especially suitable for machining of brittle materials
Machined parts by USM possess better surface finish and higher
structural integrity.
USM does not produce thermal, electrical and chemical
abnormal surface.
DISADVANTAGES:
USM has higher power consumption and lower material-removal
rates than traditional fabrication processes.
Tool wears fast in USM.
Machining area and depth is restraint in USM.
9. Laser Beam Machining (LBM)
Laser-beam machining is a thermal material-removal process that
utilizes a high-energy, coherent light beam to melt and vaporize
particles on the surface of metallic and non-metallic workpieces.
Lasers can be used to cut, drill, weld and mark. LBM is particularly
suitable for making accurately placed holes.
10. ADVANTAGES:
No limit to cutting path as the laser point can move any path.
The process is stress less allowing very fragile materials to be laser
cut without any support.
Very hard and abrasive material can be cut.
Sticky materials are also can be cut by this process.
High accuracy parts can be machined.
No cutting lubricants required
No tool wear
Narrow heat effected zone
LIMITATIONS:
Uneconomic on high volumes compared to stamping
Limitations on thickness due to taper
High capital cost
High maintenance cost
Assist or cover gas required
11. Water Jet Cutting
Water jet technology uses the principle of pressurising water to
extremely high pressures, and allowing the water to escape through a
very small opening called “orifice” or “jewel”. Water jet cutting uses
the beam of water exiting the orifice to cut soft materials. This
method is not suitable for cutting hard materials. The inlet water is
typically pressurised between 1300 – 4000 bars. This high pressure is
forced through a tiny hole in the jewel, which is typically 0.18 to 0.4
mm in diameter.
12. ADVANTAGES:
There is no heat generated in water jet cutting; which is especially.
useful for cutting tool steel and other metals where excessive heat
may change the properties of the material.
Unlike machining or grinding, water jet cutting does not produce any
dust or particles that are harmful if inhaled.
It reduce the costs.
Since no heat is applied on the materials, cut edges are clean with
minimal burr.
LIMITATIONS:
A limited number of materials can be cut economically.
Thick parts cannot be cut by this process economically and
accurately.
Taper is also a problem with water jet cutting in very thick materials.
Taper is when the jet exits the part at different angle than it enters
the part, and cause dimensional inaccuracy.
13. Abrasive Water Jet Cutting
The water jet contains abrasive particles
such as silicon carbide or aluminium oxide
in order to increase the material removal
rate above that of water jet machining.
Almost any type of material ranging from
hard brittle materials such as ceramics,
metals and glass to extremely soft materials
such as foam and rubbers can be cut by
abrasive water jet cutting. This process is
particularly suitable for heat sensitive
materials that cannot be machined by
processes that produce heat while
machining. This is similar to water jet
cutting apart from some more features
underneath the jewel. In this process, high
velocity water exiting the jewel creates a
vacuum which sucks abrasive from the
abrasive line, which mixes with the water in
the mixing tube to form a high velocity
beam of abrasives.
14. ADVANTAGES:
In most of the cases, no secondary finishing required. Typical finish
achieved is125-250 microns.
No cutter induced distortion.
Low cutting forces on workpieces.
Limited tooling requirements.
Little to no cutting burr.
No heat affected zone. Therefore, eliminates thermal distortion
Localises structural changes.
Smaller kerf size reduces material wastages.
No cutter induced metal contamination.
No slag or cutting dross.
Precise, multi plane cutting of contours, shapes, and bevels of any
angle.
LIMITATIONS:
Cannot drill flat bottom.
Cannot cut materials that degrades quickly with moisture
Surface finish degrades at higher cut speeds which are frequently
used for rough cutting.
High capital cost and high noise levels during operation.